OCTOBER, 2010 AA TM 3900 THERMAL SLIDING DOOR FEATURES 1 Features High performance ratings for structural, air infiltration, thermal efficiency and water resistance. Tested to applicable North American Standards: AAMA / NWDA / CSA 101 / I.S.2 / A440 Mitered panel and frame corners. Available as OX, XO, OXO and OXXO configurations. OOX and XOO configurations possible with optional vertical mullion. Accommodates 1" and 1-5/16" infills. Handle options in a variety of styles and finishes. Heavy duty stainless steel casters. Stainless steel track insert for sliding panels. Stainless steel 1-point and 2-point hookbolt locks and keepers. Optional applied interior insect screens. Polyamide thermal break allows two-color option. Permanodic anodized finishes in 7 choices. Painted finishes in standard and custom choices. Product Applications The AA TM 3900 is a high performance, thermal sliding door for use in condominiums, lofts, hotels and apartments. The AA TM 3900 is intended to be installed in "punched" openings or as a liner frame within other Kawneer framing or curtain wall systems. For specific product applications, Consult your Kawneer representative.
2 AA TM 3900 THERMAL SLIDING DOOR OCTOBER, 2010 BLANK PAGE
OCTOBER, 2010 AA TM 3900 THERMAL SLIDING DOOR INDEX 3 Architects Most extrusion and sliding door types illustrated in this catalog are standard products for Kawneer. These concepts have been expanded and modified to afford you design freedom. Some miscellaneous details are non-standard and are intended to demonstrate how the system can be modified to expand design flexibility. Please contact your Kawneer representative or Kawneer's Architectural Services Team for further assistance. TYPICAL ELEVATIONS... 4 STANDARD DETAILS... 5, 6 INTERIOR INSECT SCREEN... 7, 8 HARDWARE... 9 THERMAL CHARTS... 10-14 GUIDE SPECIFICATIONS... 1-6 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI) units are found in these details: m meter cm centimeter mm millimeter s second Pa pascal MPa megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement.
4 AA TM 3900 THERMAL SLIDING DOOR OCTOBER, 2010 TYPICAL ELEVATIONS Elevations are number keyed to details. 1 3 3 1 5 2 6 XO UNIT 3 4 1 7 7 6 5 Opp. Opp. Opp. 4 2 OX UNIT 3 1 3 7 10 6 5 7 6 9 7 Opp. Opp. Opp. Opp. OOX UNIT 4 2 3 1 7 6 8 6 Opp. Opp. 1 4 2 OXO UNIT 3 7 4 4 2 2 4 OXXO UNIT
OCTOBER, 2010 SCALE 3" = 1'-0" AA TM 3900 THERMAL SLIDING DOOR STANDARD DETAILS 5 OPENING DIM. 3/8" (9.5) FRAME HEIGHT 1-1/4" (31.7) 4-1/4" (107.9) 4-3/4" (120.6) 1 HEAD (SLIDING PANEL) 2-5/16" (58.7) OPENING DIM. 3/8" (9.5) FRAME HEIGHT 2-1/4" (57.2) 4-3/4" (120.6) 3 HEAD (FIXED PANEL) OPENING DIM. FRAME HEIGHT 3/8" (9.5) 4-1/4" (107.9) 1-1/4" (31.7) 2 SILL (SLIDING PANEL) 2-5/16" (58.7) OPENING DIM. FRAME HEIGHT 3/8" (9.5) 2-1/4" (57.2) 4 SILL (FIXED PANEL)
6 AA TM 3900 THERMAL SLIDING DOOR OCTOBER, 2010 STANDARD DETAILS SCALE 3" = 1'-0" 2-5/16" (58.7) 4-3/4" (120.6) 3/8" (9.5) 1-1/4" (31.7) 4-1/4" (107.9) FRAME WIDTH OPENING DIM. 5 JAMB (SLIDING PANEL) 4-1/2" (114.3) 6 INTERLOCKS FRAME WIDTH OPENING DIM. 2-1/4" (57.2) 7 JAMB (FIXED PANEL) 3/8" (9.5) 8-5/8" (219.1) 8 MEETING STILES 4-1/2" (114.3) 7-3/4" (196.9) 9 LOCK STILE 10 FIXED MULLION
OCTOBER, 2010 SCALE 3" = 1'-0" AA TM 3900 THERMAL SLIDING DOOR INTERIOR INSECT SCREENS 7 HEAD SILL INSECT SCREEN INSECT SCREEN INSECT SCREEN INTERLOCK INSECT SCREEN LOCK JAMB
8 AA TM 3900 THERMAL SLIDING DOOR OCTOBER, 2010 INTERIOR INSECT SCREENS SCALE 3" = 1'-0" INSECT SCREEN LOCK STILE MULLION INSECT SCREEN MEETING STILES
OCTOBER, 2010 AA TM 3900 THERMAL SLIDING DOOR HARDWARE 9 STANDARD EXTERIOR PULLS STANDARD INTERIOR PULLS FINGER PULL (BLANK) OPTIONAL EXTERIOR PULLS "D" PULL WITH LEVER "D" PULL (BLANK) OXXO INACTIVE PANEL OPTIONAL INTERIOR PULLS FINGER PULL WITH CYLINDER "D" PULL WITH CYLINDER INTERIOR PULL WITH THUMBTURN LOCKING OPTIONS "D" PULL (BLANK) HARDWARE FINISHES SATIN BLACK - Powder Coat Paint BONE WHITE - Powder Coat Paint SILVER GRAY - Powder Coat Paint 1 POINT LOCK 2 POINT LOCK STANDARD CASTER SATIN NICKEL - Plated BRIGHT BRASS - Plated, PVD Coated
10 AA TM 3900 THERMAL SLIDING DOOR OCTOBER, 2010 THERMAL CHARTS Project Specific U-Factor Example Calculation (Based on OXO Sliding Door Unit) 7' 4-1/2" 5-1/2" 6' 5-1/2" 5-1/2" 10' 4-3/4" 2-1/4" 3'-0" 4-1/2" 3'-0" 7-3/4" 3'-0" 2-1/4" 2-1/4" 7'-0" 2-1/4" Vision Area Example Glass U-Factor = 0.48 Btu/(ft 2 h F) Total Daylight (Vision) Area = 2(3' x 7') + 1(3' x 6.45') = 61.35 ft 2 Projected Total Area = 7.375' x 10.39' = 76.63 ft 2 Percent of Vision Glass = (Total Daylight Area Projected Total Area)100 = (61.35 76.63) 100 = 80%
OCTOBER, 2010 AA TM 3900 THERMAL SLIDING DOOR THERMAL CHARTS 11 System U-Factor vs Percent of Vision Area 0.90 COG U-factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) (1.14) EXAMPLE (NOT FOR DESIGN) 0.85 0.80 0.57 Btu h ft 2 F (5.00) (4.50) (4.00) (3.50) (3.00) (2.50) (2.00) (1.50) W ( m ) 2 C System U-factor 90 85 80% 75 70 65 Vision Area / Total Area (%) Based on a OXO Unit of 80% vision glass and center of glass U-Factor of 0.48, system U-Factor is equal to 0.57 Btu/(h ft 2 F)
12 AA TM 3900 THERMAL SLIDING DOOR OCTOBER, 2010 THERMAL CHARTS Note: Values in parentheses are metric. COG = Center Of Glass. Charts are generated per AAMA 507. System U-Factors for Vision Area COG U-Factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) (1.14) 0.90 0.85 0.80 Btu h ft 2 F (5.00) (4.50) (4.00) (3.50) (3.00) (2.50) (2.00) (1.50) W ( m ) 2 C System U-Factor 90 85 80 75 70 65 Vision Area / Total Area (%)
OCTOBER, 2010 AA TM 3900 THERMAL SLIDING DOOR THERMAL CHARTS 13 System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area 0.80 COG SHGC 0.15 0.10 0.05 90 85 80 75 Vision Area / Total Area (%) 70 0.15 0.10 0.05 0.00 65 System SHGC System Visible Transmittance (VT) vs Percent of Vision Area COG VT 0.15 0.10 0.80 0.15 0.10 System VT 0.05 0.05 0.00 90 85 80 75 Vision Area / Total Area (%) 70 65
14 AA TM 3900 THERMAL SLIDING DOOR OCTOBER, 2010 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr ft 2 F) Glass U-Factor 3 Overall U-Factor 4 0.48 0.59 0.46 0.58 0.44 0.56 0.42 0.54 0.38 0.52 0.36 0.51 0.34 0.32 0.48 0.47 0.28 0.26 0.44 0.24 0.43 0.22 0.41 SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.58 0.56 0.54 0.52 0.51 0.47 0.43 0.39 0.36 0.32 0.28 0.24 0.21 0.17 0.15 0.13 0.15 0.10 0.10 0.10 0.05 0.06 0.05 NOTE: For glass values that are not listed, linear interpolation is permitted. 0.49 0.41 0.37 0.34 0.26 0.22 0.19 0.15 0.11 0.07 0.04 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 2000mm wide by 2000mm high (78-3/4" by 78-3/4").