General Specifications

General Specifications YTA60 Temperature Transmitter The YTA60 is the highly accurate temperature transmitter that accepts Thermocouple, RTD, ohms or DC millivolts inputs and converts it to a to 0 ma DC or Fieldbus signal for transmission. The YTA60 supports HART and FOUNDATION fieldbus TM communication protocols. HART types are certified as complying with SIL for safety requirement. FEATURES High reliability Dual-compartment housing realizes high resistance capability to harsh environments. Variety of sensor inputs The type of sensor input is user-selectable from thermocouples (T/C), RTDs, ohms, or DC millivolts. Digital communication HART protocol revision is 7 and FOUNDATION fieldbus TM ITK vesion is 6.. The instrument configuration can be changed by the user with using the Fieldmate or Handheld terminal. Local Parameter Setting Parameter configuration by the push button offers easy and quick setup for parameters. Self-diagnostics function Continuous self-diagnostics capability ensures longterm performance and lower cost of ownership. Dual universal inputs Dual input can accept two thermocouple, RTD, ohm or DC millivolt inputs. Differential or average temperature measurement is selectable. The sensor backup function for automatically switches-over from the primary to the backup upon sensor failure. STANDARD SPECIFICATIONS PERFORMANCE SPECIFICATIONS Accuracy HART communication type: A/D accuracy/span + D/A accuracy (See Table on page.) Fieldbus communication type: A/D accuracy (See Table on page.) Cold Junction Compensation Accuracy ± 0. C (± 0.9 F) for T/C only Ambient Temperature Effect (per 0 C change) ±0.% or ±(Temperature coefficient/span), whichever is greater. (See Table on page.) Stability RTD: ±0.% of reading or ±0. C per years, whichever is greater at ± C. T/C: ±0.% of reading or ±0. C per year, whichever is greater at ± C. Year Stability RTD: ±0.% of reading or ±0. C, whichever is greater at ± C. T/C: ±0.% of reading or ±0. C, whichever is greater at ± C. Vibration Effect The YTA60 is tested to the following specifications with no effect on performance per IEC 60770-0 to 60 Hz 0. mm peak displacement 60 to 000 Hz g Power Supply Effect ±0.00% of calibrated span per volt Yokogawa Electric Corporation -9-, Nakacho, Musashino-shi, Tokyo, 80-870 Japan Tel.: 8---690 Fax.: 8---08 Copyright Sep. 06 th Edition Mar. 07

FUNCTIONAL SPECIFICATIONS Input Signals Input number: single and dual input Input type is selectable: Thermocouples, -, -, and -wire RTDs, ohms and DC millivolts. See Table. on page. Input Signal Source Resistance (for T/C, mv) kω or lower Input Lead Wire Resistance (for RTD, ohm) 0 Ω per wire or lower Span & Range Limits See Table. on page. Output Signals Two wire to 0 ma DC type Output range:.68 to 0.8 ma HART protocol is superimposed on the to 0 ma signal. Any single value among followings can be selected as the analog output signal. Sensor, Terminal Temperature. Dual input type, same as above plus; Sensor, Average, and Differential Temperature. Also, up to three of the above values can be displayed on LCD display or read via communication. Fieldbus communication type Output signal based on FOUNDATION fieldbus TM communication protocol. Isolation Input/Output/GND isolated to 00V DC Except lightning protector option. Manual Test Output Function The output value can be set manually. Sensor Burnout (HART type) High (.6 ma DC) or Low (.6 ma DC), user selectable. Output in Transmitter Failure (HART type) Down-scale: %,. ma DC or less, sensor burnout.%,.6 ma (Optional code C) Down-scale: %,. ma DC or less (Optional code C) Up-scale: 0%,.6 ma DC or more (Standard or Optional code C) Update Time (HART type) Approximately 0. seconds for a single sensor (0.8 second for dual sensors) at damping time 0 Turn-on Time (HART type) Approximately 6 seconds for a single sensor (7 seconds for dual sensors) Damping Time Constant Selectable from 0 to 00 seconds Self-Diagnostics Self-diagnostic function based on the NAMUR NE07 standard detects failures in the hardware, configuration and communications. Sensor-Diagnostics Sensor failure: Detect the disconnection of sensor. Sensor line information: Measure the line resistance. Sensor drift: Detect the difference between sensor and sensor. Fieldbus Functions (Fieldbus type) Functional specifications for Fieldbus communication conform to the standard specifications (H) of FOUNDATION Fieldbus. Function Block (Fieldbus type) Resource block The resource block contains physical transmitter information. Transducer block The transducer block contains the actual measurement data and information about sensor type and configuration and diagnostics. LCD display block The LCD display block is used to configure the local display, if an LCD display is being used. Analog input (AI) Four independent AI blocks can be selected. Digital input (DI) Four DI function blocks can be used as a limit switch for those temperature. Other function block As other Function blocks, Arithmetic (AR), Signal Characterizer (SC), Input Selector (IS), and two PID function blocks are available. Function block Execution time (ms) AI 0 DI 0 SC 0 IS 0 AR 0 PID Link master function This function enables backup of network manager and local control only by field devices. Alarm function Fieldbus models securely support various alarm functions, such as High/Low alarm, notice of block error, etc. based on FOUNDATION fieldbus specifications. Software download function This function permits to update YTA software via a FOUNDATION fieldbus. Based on Foundation fieldbus specifications (FF88) Download class: Class EMC Conformity Standards EN66- Class A, Table EN66-- EN66-- (for fieldbus) SIL Certification Hart communication type certified in compliance with IEC 608: 00. Functional Safety of Electrical/electronic/ Programmable electronic related systems; SIL capability for single transmitter use SIL capability for dual transmitter use Mar. 07, 07-00

Safety Requirement Standards EN600-, C. No.600- Altitude of installation site: Max.,000 m above sea level Installation category: I (Anticipated transient overvoltage 0 V) Pollution degree: Indoor/Outdoor use EN600--00, C. No.600--00 Measurement category: O (Other) (Measurement Input voltage: 0mVdc max) NORMAL OPERATING CONDITION (Optional features or approval codes may affect limits.) Ambient Temperature Limits 0 to 8 C ( 0 to 8 F) 0 to 80 C ( to 76 F) (with indicator model) Ambient Humidity Limits 0 to 00% RH at 0 C (0 F) Supply Voltage Requirements HART type 0. to V DC for general use and flameproof type 0. to V DC for lightning protector (option code /A) 0. to 0 V DC for intrinsically safe and non-incendive type Minimum voltage limited at 6.6 V DC for digital communications HART With V DC supply, up to a 0Ω load can be used. See graph below. 600 External load resistance 0 R= E-0. 0.0 Digital Communication range HART PHYSICAL SPECIFICATIONS Enclosure Material & coating Low copper cast aluminum alloy with polyurethane, mint-green paint. (Munsell.6BG./.9 or its equivalent), or ASTM CF-8M Stainless Steel Degrees of protection IP66/IP67, TYPE X Name plate and tag 6 SST Mounting Optional mounting brackets can be used either for two-inch pipe or flat panel mounting. Terminal screws M screws Integral Indicator (with indicator model) -digit numerical display, 6-digit unit display and bar graph. Local Parameter Setting (with indicator model) Parameter configuration by the push button offers easy and quick setup for parameters. Accessible parameters are different with each output cord. Weight Aluminum housing:. kg (.9 lb) without integral indicator and mounting Integral indicator: 0. kg (0. lb) Bracket for horizontal pipe: 0. kg Bracket for vertical pipe:.0 kg Stainless housing:. kg (6.8 lb) without integral indicator and mounting Integral indicator: 0. kg (0.7 lb) Connections Refer to MODEL AND SUFFIX CODE. R(Ω) 0. 6.6. Power supply voltage E (V) Figure. Relationship Between Power Supply Voltage and External Load Resistance F0E.ai Fieldbus type 9 to V DC for general use, flameproof type, and non-incendive type 9 to 0 V DC for intrinsically safe type 9 to 7. V DC for FISCO field device Communication Requirements Supply Voltage: 9 to V DC Current Draw: Steady state: ma (max) Software download state: ma (max) Load Requirements (HART type) 0 to 90Ω for operation 0 to 600Ω for digital communication Mar. 07, 07-00

Table. Sensor type, measurement range, and accuracy T/C RTD Sensor Type B E J K N R S T C W Standard IEC608 ASTM E988 Measurement Range Minimum A/D Accuracy C F Span C F 00 to 00 00 to 80-00 to -0-0 to 000-00 to -0-0 to 00-00 to -0-0 to 7-00 to -0-0 to 00-0 to 0 0 to 600 600 to 768-0 to 0 0 to 768-00 to -0-0 to 00 0 to 000 000 to 00 0 to 00 00 to 00 00 to 000 000 to 00-00 to -0-0 to 900 to 7 7 to 08-8 to -8-8 to 8-8 to -8-8 to 9-8 to -8-8 to 0-8 to -8-8 to 7-8 to to to -8 to to -8 to -8-8 to 7 to 6 6 to 7 to 7 7 to to 6 6 to 7-8 to -8-8 to 6 C ( F) ±.0 ± 0.77 ± 0. ± 0. ± 0. ± 0. ± 0. ± 0. ± 0. ± 0. ±.0 ± 0.7 ± 0. ±.0 ± 0.6 ± 0. ± 0. ± 0.7 ±.0 ± 0.9 ± 0.6 ± 0.7 ±.0 ± 0. ± 0. ±. ±.9 ± 0.7 ± 0.6 ± 0.6 ± 0. ± 0.9 ± 0. ± 0.9 ± 0.7 ±.8 ±.6 ± 0.9 ±.8 ±.08 ± 0.6 ± 0.6 ±.6 ±.8 ±.6 ±.08 ±.6 ±.8 ± 0.6 ± 0. L DIN70 U -00 to 600-8 to ± 0. ± 0.6 Pt00-00 to 80-8 to 6 ± 0. ± 0. Pt00-00 to 80-8 to 6 ± 0. ± 0. IEC607 Pt00-00 to 80-8 to 6 ± 0.8 ± 0. Pt000-00 to 00-8 to 7 0 C ± 0.8 ± 0. JPt00-00 to 00-8 to 9 (8 F) ± 0.6 ± 0.9 Cu0 SAMA RC- -70 to 0-9 to 0 ±. ±. Ni0-70 to 0-9 to 608 ± 0. ± 0. mv -0 to 0 [mv] mv ±0.0 [mv] ohm 0 to 000 [Ω] 0 Ω ±0. [Ω] Note : Total Accuracy = (A/D Accuracy / Span + D/A Accuracy) or (± 0.% of calibrated span), whichever is greater. Accuracy of Fieldbus type: A/D Accuracy. For T/C input, add Cold Junction Compensation Error (± 0. C) to the total accuracy. Example: when selecting Pt00 with measurement range of 0 to 00 C 0. C / 00 C 00% of span +0.0% of span = 0.06% of span Since the value is smaller than ±0.% of span, the total accuracy is ±0.%. Note : T/C C type is same as W (ASTM E988). D/A Accuracy ±0.0% of span Mar. 07, 07-00

Table. Temperature coefficient Sensor Type Thermocouples E, J, K, N, T, L, U Thermocouples R, S, W, C Temperature Coefficient 0.08 C + 0.0% of abs.reading 0. C + 0.0% of abs.reading Thermocouple B 00 C Reading < 00 C C + 0.0% of abs.reading RTD mv ohm 00 C Reading 0. C + 0.0% of abs.reading 0.08 C + 0.0% of abs.reading 0.00 mv + 0.0% of abs.reading 0. Ω + 0.0% of reading Note: The abs.reading for thermocouples and RTD means the absolute value of the reading in C. Example of abs.reading When the temperature value is 0 Kelvin, abs.reading is.. 0 7. =. Note: Ambient Temperature Effect per 0 C change is ±0.% or ±(temperature coefficient/span), whichever is greater. Example of Ambient Temperature Effect Conditions: ) Input Sensor: Pt00 ) Calibration Range: 00 to 00 C ) Reading value: 0 C Ambient Temperature Effect per 0 C Temperature Coefficient/Span=(0.08 C+0.0/00 0 C )/{00 C ( 00 C)}= 0.000 0.0% Therefore, Ambient Temperature Effect is ±0.%/0 C Sep. 0, 06-00

6 MODEL AND SUFFIX CODES Model Suffix Codes Description YTA60................................ Temperature Transmitter Output signal -J.......................... -F.......................... A....................... Always A Sensor input...................................... Housing code A............... C............... Electrical connection 0....................................... Integral indicator D......... N......... Mounting bracket B...... D...... J...... K...... N...... Option codes to 0 ma DC with digital communication HART 7protocol Digital communication (FOUNDATION Fieldbus protocol) Single Double Aluminum Stainless G/ female / NPT female M0 female Digital indicator with Local Operating Switch None SUS0 stainless steel -inch horizontal pipe mounting bracket * SUS0 stainless steel -inch vertical pipe mounting bracket SUS6 stainless steel -inch horizontal pipe mounting bracket * SUS6 stainless steel -inch vertical pipe mounting bracket None / Optional specification *: For flat-panel mounting, please prepare bolts and nuts. OPTIONAL SPECIFICATION Item Description Code Lightning protector Allowable current: Max. 6000A(8 0µs), repeating 000A(8 0µs), 00 times A Painting * Color change Munsell code: N. Black P Amplifier cover only Munsell code: 7.BG/., Jade green P Metallic silver P7 Color change Munsell code: 7. R/ Red Amplifier and terminal Covers PR Coating change * High anti-corrosion coating X Output signal low-side in transmitter failure * NAMUR NE compliant * Output signal Low-side: %,. ma DC or less. Sensor burnout is also set to 'Low':.%,.6 ma DC. Output signal limits:.8 ma to 0. ma Failure alarm down-scale: output status at CPU failure and hardware error is %,. ma or less. Sensor burnout is also set to Low:.%,.6 ma DC. Failure alarm up-scale: output status at CPU failure and hardware error is 0%,.6 ma or more. In this case Sensor burnout is High: 0%,.6 ma DC. Data configuration * Description into Descriptor parameter of HART protocol (max. 6 characters) CA Wired tag plate SUS6 stainless steel tag plate wired onto transmitter N Sensor matching RTD sensor matching function CM *: Not applicable for Stainless housing. *: Not applicable for Fieldbus type. *: Not applicable for color change. C C C Sep. 0, 06-00

7 OPTIONAL SPECIFICATION (For Explosion Protected type) ATEX Item Description Code -0mA: [Intrinsically safe approval ] Applicable Standard: EN 60079-0: 0+A:0, EN 60079-: 0 Certificate No. FM6ATEX009X II G Ex ia IIC T T Ga Ambient Temperature: 0 to 70 C for T, 0 to 0 C for T Enclosure: IP66/IP67 in accordance with only IEC 609 Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.0W, Ci=nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -, C,,,,, ] to Earth terminal [+, -, C] to [,,,, ] [Flameproof and Dust Ignition Proof Approval] Applicable Standard: EN 60079-0:0+A:0, EN 60079-:0, EN 60079-:0 Certificate: KEMA 07ATEX00 II G Ex db IIC T6/T Gb, II D Ex tb IIIC T70 C/T90 C Db Ambient Temperature for Gas Atmospheres: 0 to 7 C for T6, 0 to 80 C for T Ambient Temperature for Dust Atmospheres: 0 to 6 C for T70 C, 0 to 80 C for T90 C Enclosure: IP66/IP67 Electrical Connection: / NPT female and M0 female * Fieldbus: [Intrinsically safe approval ] Applicable Standard: EN 60079-0: 0+A:0, EN 60079-: 0 Certificate No. FM6ATEX009X II G Ex ia IIC T Ga Ambient Temperature: to 60 C Enclosure: IP66/IP67 in accordance with only IEC 609 FISCO field device Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.W, Ci=.nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -,,,,, ] to Earth terminal [+, -] to [,,,, ] [Flameproof and Dust Ignition Proof Approval] Same as KU KU KU Dec., 06-00

8 IECEx Item Description Code -0mA: [Intrinsically safe approval] Applicable Standard: IEC 60079-0: 0, IEC 60079-: 0 Certificate No. IECEx FMG 6.00X Ex ia IIC T T Ga Ambient Temperature: 0 to 70 C for T, 0 to 0 C for T Enclosure: IP66/IP67 Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.0W, Ci=nF, Li=0mH Sensor circuit: Uo=6V, Io=90mA, Po=mW, Co=0μF, Lo=.9mH Dielectric strength: 00 V a.c.r.m.s., min [+, -, C,,,,, ] to Earth terminal [+, -, C] to [,,,, ] [Flameproof and Dust Ignition Proof Approval] Applicable standard: IEC 60079-0:0, IEC 60079-:0-06, IEC 60079-:0 Certificate: IECEx KEM 07.00 Ex db IIC T6/T Gb, Ex tb IIIC T70 C/T90 C Db Ambient Temperature for Gas Atmospheres: 0 to 7 C ( 0 to 67 F) for T6, 0 to 80 C ( 0 to 76 F) for T Ambient Temperature for Dust Atmospheres: 0 to 6 C ( to 9 F) for T70 C, 0 to 80 C ( to 76 F) for T90 C Enclosure: IP66/IP67 Electrical Connection: / NPT female and M0 female * Fieldbus: [Intrinsically safe approval] Applicable Standard: IEC 60079-0: 0, IEC 60079-: 0, Certificate No. IECEx FMG 6.00X Ex ia IIC T Ga, Ambient Temperature (Ex ia): to 60 C Ex ic IIC T Gc, Ambient Temperature (Ex ic): 0 to 70 C Enclosure: IP66/IP67 Overvoltage category: I Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.W, Ci=.nF, Li=0mH FISCO field device Sensor circuit: Uo=6V, Io=90mA, Po=mW, Co=0μF, Lo=.9mH Supply/Output circuit: Ui=V, Ci=.nF, Li=0mH FISCO field device Sensor circuit: Uo=6V, Io=90mA, Po=mW, Co=0μF, Lo=.9mH Dielectric strength: 00 V a.c.r.m.s., min [+, -,,,,, ] to Earth terminal [+, -] to [,,,, ] [Flameproof and Dust Ignition Proof Approval] Same as SU SU SU Feb. 8, 07-00

9 FM (US) Item Description Code -0mA: [Intrinsically safe approval/non-incendive approval] Applicable standard: Class 600:0, Class 60:0, Class 6:00, Class 80:00, ANSI/ISA-60079-0:0,ANSI/ISA-60079-:0, NEMA 0:00, ANSI/IEC 609:00 (R0) Class I, II, III Division, Groups A, B, C, D, E, F, G, T T Class I Zone 0 AEx ia IIC T T Class I, II, Division, Groups A, B, C, D, F, G, T T Class III, Division T T Class I Zone Group IIC T T Ambient Temperature: 0 to 70 C for T, 0 to 0 C for T Enclosure Type X, IP66/IP67 in accordance with only IEC 609 Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.0W, Ci=nF, Li=0mH Supply/Output circuit: Ui=0V, Ci=nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -, C,,,,, ] to Earth terminal [+, -, C] to [,,,, ] [Explosionproof approval] Applicable standard: Class 600, Class 6, Class 80, ANSI/NEMA0 Class I, Division, Groups A, B, C and D.; Class II/III, Division, Groups E, F and G. "FACTORY SEALD, CONDUIT SEAL NOT REQUIRED." Enclosure Ratings: TYPE X Temperature Class: T6 Ambient Temperature: 0 to 60 C ( 0 to 0 F) Electrical Connection: /NPT female * Fieldbus: [Intrinsically safe approval/non-incendive approval] Applicable standard: Class 600:0, Class 60:0, Class 6:00, Class 80:00, ANSI/ISA-60079-0:0,ANSI/ISA-60079-:0, NEMA 0:00, ANSI/IEC 609:00 (R0) Class I, II, III Division, Groups A, B, C, D, E, F, G T Class I Zone 0 AEx ia IIC T Class I, II, Division, Groups A, B, C, D, F, G T Class III, Division T Class I Zone Group IIC T Ambient Temperature: to 60 C Enclosure Type X, IP66/IP67 in accordance with only IEC 609 FISCO field device Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.W, Ci=.nF, Li=0mH Supply/Output circuit: Ui=V, Ci=.nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -,,,,, ] to Earth terminal [+, -] to [,,,, ] [Explosionproof approval] Same as FU FU FU Dec., 06-00

0 CSA * Item Description Code FM (Canada) * -0mA: [Intrinsically safe approval/non-incendive approval] Applicable standard: CAN/CSA-C. No. 0:00 (R0), CAN/CSA-C. No. 9.:007 (R0), CAN/CSA-C. No. 9.:007 (R0), C. No.:987 (R0), CAN /CSA-C. No. 60079-0:0, CAN/CSA-C. No. 60079-:0, CAN/CSA-C. No. 609:00 (R00), CAN/CSA-C. No. 600-:0, CAN/CSA-C. No. 600--00:0 Class I, II, III, Division, Groups A, B, C, D, E, F, G, T T Ex ia IIC T T Ga Class I, II, Division, Groups A, B, C, D, F, G T T Class III Division T T Ambient Temperature: 0 to 70 C for T, 0 to 0 C for T Enclosure Type: X, IP66/IP67 in accordance with only IEC 609 Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.0W, Ci=nF, Li=0mH Supply/Output circuit: Ui=0V, Ci=nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -, C,,,,, ] to Earth terminal [+, -, C] to [,,,, ] [Explosionproof approval] Applicable standard: C. No.0, C. No.0., C. No., C. No.0, C. No.9, C. No., C. No.7, C. No., C. No.600- C. No.600--00 Class I, Groups B, C and D, Class II, Groups E, F and G, Class III. For Class I, Division Groups ABCD Locations FACTORY SEALED, CONDUIT SEAL NOT REQUIRED Enclosure TYPE X Temperature Class: T6 Ambient Temperature: 0 to 60 C Electrical Connection: / NPT female * Fieldbus: [Intrinsically safe approval/non-incendive approval] Applicable standard: CAN/CSA-C. No. 0:00 (R0), CAN/CSA-C. No. 9.:007 (R0), CAN/CSA-C. No. 9.:007 (R0), C. No.:987 (R0), CAN /CSA-C. No. 60079-0:0, CAN/CSA-C. No. 60079-:0, CAN/CSA-C. No. 609:00 (R00), CAN/CSA-C. No. 600-:0, CAN/CSA-C. No. 600--00:0 Class I, II, III, Division, Groups A, B, C, D, E, F, G T Ex ia IIC T Ga Class I, II, Division, Groups A, B, C, D, F, G T Class III Division T Ambient Temperature : to 60 C Enclosure Type: X, IP66/IP67 in accordance with only IEC 609 FISCO field device Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.W, Ci=.nF, Li=0mH Supply/Output circuit: Ui=V, Ci=.nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -,,,,, ] to Earth terminal [+, -] to [,,,, ] [Explosionproof approval] Same as CU CU CU Dec., 06-00

NEPSI Item Description Code -0mA and Fieldbus: [Flameproof and Dust Ignition Proof Approval] Applicable Standard: GB86.-00, GB86.-00, GB76.-0, GB76.-0 Certificate No. GYJ6.96X Ex d IIC T6/T Gb, Ex td A IP66/IP67 T70 C/T90 C Ambient Temperature for Gas Atmospheres: 0 to 7 C for T6, 0 to 80 C for T Ambient Temperature for Dust Atmospheres: 0 to 6 C for T70 C, 0 to 80 C for T90 C Enclosure: IP66/IP67 Electrical Connection: / NPT female and M0 female * -0mA: [Intrinsically safe approval ] Applicable Standard: GB 86.-00, GB 86.-00 GB 86.0-00 Certificate No. GYJ6.X Ex ia IIC T/T Ga Ambient Temperature: 0 to 70 C for T, 0 to 0 C for T Enclosure: IP66/IP67 in accordance with only IEC 609 Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.0W, Ci=nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -, C,,,,, ] to Earth terminal [+, -, C] to [,,,, ] Fieldbus: [Intrinsically safe approval] Applicable Standard: GB 86.-00, GB 86.-00, GB86.0-00 Certificate No. GYJ6.X Ex ia IIC T Ga Ambient Temperature: to 60 C for T Enclosure: IP66/IP67 in accordance with only IEC 609 FISCO field device Supply/Output circuit: Ui=0V, Ii=00mA, Pi=.W, Ci=.nF, Li=0mH Dielectric strength: 00 V a.c.r.m.s., min [+, -,,,,, ] to Earth terminal [+, -] to [,,,, ] *: Applicable for Electrical Connection Code and. *: Applicable for Electrical Connection Code. *: For Explosionproof approval. *: For Intrinsically safe approval/non-incendive approval. NF NS NS Dec., 06-00

DIMENSIONS -inch horizontal pipe mounting Unit: mm (Approx. inch) Electrical Connection (Output signal) (.7) Electrical Connection (Input signal) With Indicator (Optional) 6.(.7) 7. (.8) 66.(.60) 8. (0.7) Terminal Cover 6(6.6) 0(.0) Shrouding Bolt (For Explosionproof type) 0 (.7) ø9(.66) Ground Terminal Tag Plate (0.98) Horizontal Pipe Mounting Bracket (Optional) 6(.) -inch pipe ø60.(ø.8) -inch vertical pipe mounting Electrical Connection (Output signal) (.7) Electrical Connection (Input signal) With Indicator (Optional) 6.(.7) 7. (.8) 66.(.60) 8. (0.7) Terminal Cover Shrouding Bolt (For Explosionproof type) ø9(.66) 9.(7.) 09.(8.) 6 (.8) Ground Terminal Tag Plate Vertical Pipe Mounting Bracket (Optional) -inch pipe ø60.(ø.8) 0(.98) 70(.76) 6(.) 98(.86) F0E.ai Dec., 06-00

Terminals Communication Terminals Connection hook CHECK METER Connection hook * Input Wiring M0. -deep female for mounting bracket Terminal Configuration Power supply and output terminal External indicator (ammeter) termial * Ground terminal * : When using an external indicator or a check meter, the internal resistance must be 0Ω or less. The hook is not available for Fieldbus communication type. F0E.ai (+) ( ) Thermocouple and DC voltage (A) (B) (B) RTD and resistance (-wire) Single input (A) (B) RTD and resistance (-wire) (A) (A) (B) (B) RTD and resistance (-wire) ( ) (+) (+) Thermocouple and DC voltage (+) ( ) (B) (B) (A) Thermocouple + RTD and resistance (-wire) (A) (B) (B) ( ) (+) Dual input (A) (B) (B) (B) (B) (A) RTD and resistance (-wire) (A) (B) (B) (A) RTD and resistance (-wire) RTD and resistance (-wire) + Thermocouple F0E.ai Dec., 06-00

< Ordering Information > Specify the following when ordering Model, suffix codes, and optional codes. If not specified, the instrument is shipped with the settings shown in Table A and B. Specify the following when necessary. -0mA Type (HART Type). Sensor type. For RTD and resistance input, specify the number of wire as well. (Example: Pt00 -wire system) For sensor input code-, specify the type for two inputs. In this case, two engineering values are alternately displayed on the integral indicator with sensor back up DISABLE.. Calibration range and unit ) Calibration range can be specified within the measurement range shown in Table. Also, set the upper limit is larger than the lower limit. ) Specify one range from C, K, F or R for temperature input. It is not necessary to specify the unit of mv and ohm inputs, for these units automatically will be mv or Ω.. Tag Number (if required) Specify Tag number (up to 6 Characters) to be engraved on the tag plate. The specified letters are written on TAG_Name (6 Characters) in the amplifier memory.. Software tag Specified characters (up to characters) are set as Tag (the first 8 characters) and Long tag ( characters) in the amplifier memory. Use alphanumeric capital letters. When the SOFTWARE TAG is not specified, TAG NO is set as Tag (the first 8 characters) and Long tag ( characters) in the amplifier memory.. Other factory configurations Specifying option code CA will allow further configuration at factory. Descriptor (up to 6 characters) 6. Sensor back up Select DISABLE or ENABLE. Fieldbus Type. Sensor type. For RTD and resistance input, specify the number of wire as well. For sensor input code-, specify the type for two inputs. (Example: Pt00 -wire system) In this case, two engineering values are alternately displayed on the integral indicator with sensor back up DISABLE.. Calibration range (XD_SCALE) For sensor input code-, specify the range for two inputs.. Units of calibration range: Specify only one unit from the table, Settings when shipped. For sensor input code-, specify the unit for two inputs.. Output mode (L_TYPE) Select Direct or Indirect.. Output scale (OUT_SCALE) For sensor input code-, specify the scale for two inputs. 6. Output scale unit Specify only one unit from the table, Settings when shipped. For sensor input code-, specify the unit for two inputs. 7. Tag Number Specify Tag number (up to 6 Characters) to be engraved on the tag plate. 8. Software Tag (PD_TAG) Specify software tag (up to Characters) to be written on the amplifier memory. 9. Node Address 0. Operation Functional Class Select BASIC or LINK MASTER.. Sensor back up Select DISABLE or ENABLE. < Factory Setting > Table A. -0mA Type Input sensor type * Wire connection (For RTD) * Calibration range Calibration unit Sensor burnout * Output in Transmitter failure * Sensor backup Tag No. Pt00 or as specified in order -wire system or as specified in order 0 to 00 or as specified in order C or as specified in order High (0%,.6 ma DC) High (0%,.6 ma DC or more) DISABLE or as specified Blank or as specified in order *: For sensor input code-, sensor is set in nonconnection. *: Except when Optional code C or C is specified. Table B. Fieldbus Type Input sensor type * Wire connection (For RTD) * Calibration range * Calibration unit Output Scale * 0 to 00% Output mode Direct Node Address (in hexadecimal) Operation functional Class Sensor backup * Tag Number (Tag plate) Software Tag (PD_TAG) Pt00 or as specified in order -wire system or as specified in order 0 to 00 or as specified in order C or as specified in order 0xF unless otherwise specified in order BASIC, or as specified in order DISABLE or as specified in order Blank or as specified in order TT00 unless otherwise specified in order. *: For sensor input code-, sensor is set in nonconnection. *: Channel settings of AI function blocks depend on sensor backup setting. Disable: AI=Sensor, AI=Terminal temperature Enable: AI=Backup temperature, AI=Terminal temperature Subject to change without notice. Jan. 6, 07-00