Bauar t gepruft Sicherheit egelma ge od o s be wac g www. tuv.com ID 2000000000 120W Constant Voltage Constant Current LED Driver F 110 M M SELV IP65 IP67 Type HL S&E Features Constant Voltage Constant Current mode output Metal housing with class I design Builtin active PFC function IP67 / IP65 rating for indoor or outdoor installations Function options: output adjustable via potentiometer; 3 in 1 dimming; Timer dimming Typical lifetime > 62000 hours 7 years warranty Applications LED street lighting LED highbay lighting Parking space lighting LED fishing lamp LED greenhouse lighting Type HL for use in Class Ⅰ, Division 2 hazardous (Classified) location. Description is a 120W AC/DC LED driver featuring the dual mode constant voltage and constant current output. HLG120H operates from 90~305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to 93.5%, with the fanless design, the entire series is able to operate for 40 ~ case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HLG120H is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system. Model Encoding HLG 120H 48 A Function options Rated output voltage (12V/15V/20V/24V/30V/36V/42V/48V/54V) Rated wattage Series name Type IP Level Function Note Blank IP67 Io and Vo fixed In Stock A IP65 Io and Vo adjustable through builtin potentiometer In Stock B IP67 3 in 1 dimming function (1~10VDC, 10V PWM signal and resistance) In Stock D IP67 Timer dimming function, contact MEAN WELL for details(safety pending). By request
SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS NOTE DC VOLTAGE RATED CURRENT RATED POWER RIPPLE & NOISE (max.) Note.2 150mVpp VOLTAGE ADJ. RANGE CURRENT ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER CURRENT SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY WITHSTAND VOLTAGE ISOLATION RESISTANCE Note.6 1200ms,50ms/115VAC Note.5 TOTAL HARMONIC DISTORTION STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION HLG120H12 HLG120H15 HLG120H20 HLG120H24 HLG120H30 HLG120H36 HLG120H42 HLG120H48 12V 15V 20V 24V 30V 10A 8A 6A 5A 4A 120W 120W 120W 120W 120W 122.4W 10.8 ~ 13.5V 5 ~ 10A ±2.5% 47 ~ 63Hz 92% 92% 93% 93% 93% 93% 93% 93.5% 93.5% 1.4A / 115VAC 0.6A / 230VAC 0.55A / 277VAC <0.75mA / 277VAC 95 ~ 108% 150mVpp 13.5 ~ 17V 4 ~ 8A ±2.0% Constant current limiting, recovers automatically after fault condition is removed Constant current limiting, recovers automatically after fault condition is removed 14 ~ 17V 18 ~ 21V 23 ~ 27V 28 ~ 34V 34 ~ 38V 41 ~ 46V 47 ~ 53V 54 ~ 63V 59 ~ 65V Shut down o/p voltage, recovers automatically after temperature goes down 20 ~ 95% RH noncondensing 40 ~, 10 ~ 95% RH ±0.03%/ (0 ~ 60 ) 150mVpp 17 ~ 22V 3 ~ 6A 150mVpp 22 ~ 27V 2.5 ~ 5A 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC 200mVpp 27 ~ 33V I/PO/P, I/PFG, O/PFG:M Ohms / 500VDC / 25 / 70% RH Note.8 Compliance to EN55015, EN55032 Class B, EN6032 Class C (@ load 50%) ; EN6033,GB17743 and GB17625.1 EMC IMMUNITY Compliance to EN6042,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge immunity LineEarth 4KV, LineLine 2KV) MTBF 559.5K hrs min. Telcordia SR332 (Bellcore); 167.1Khrs min. MILHDBK217F (25 ) DIMENSION 220**38.8mm (L*W*H) PACKING 1.12Kg; 12pcs/14.4Kg/0.8CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pairwire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Please refer to "DRIVING METHODS OF LED MODULE". 5. Derating may be needed under low input voltages. Please refer to STATIC CHARACTERISTIC sections for details. 6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must requalify EMC Directive on the complete installation again. 8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains. 9. This series meets the typical life expectancy of >62,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75 or less. 10. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com 2 ~ 4A 200mVpp 33 ~ 40V 1.7 ~ 3.4A 1.4 ~ 2.9A 200mVpp 43 ~ 53V 1.2 ~ 2.5A ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±2.0% ±1.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% COLD START 60A(twidth=375 μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 Shut down o/p voltage with autorecovery or repower on to recovery 42V 3.4A 2.9A 2.5A 121.8W 200mVpp 38 ~ 46V HLG120H54 CONSTANT CURRENT REGION Note.4 6 ~12V 7.5 ~ 15V 10 ~ 20V 12 ~ 24V 15 ~ 30V 18 ~ 36V 21 ~ 42V 24 ~ 48V 27 ~ 54V MAX. No. of PSUs on 16A CIRCUIT BREAKER MAX. CASE TEMP. Adjustable for AType only (via builtin potentiometer) Adjustable for AType only (via builtin potentiometer) 12ms / 115VAC, 230VAC 500ms,50ms/230VAC 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) PF 0.98/115VAC, PF 0.95/230VAC, PF 0.93/277VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< 20% (@ load 50% / 115VAC,230VAC; @ load 75% / 277VAC) (Please refer to " TOTAL HARMONIC DISTORTION (THD)" section) 36V 5 units (circuit breaker of type B) / 9 units (circuit breaker of type C) at 230VAC Tcase= 40 ~ (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) Tcase= 48V 120W 54V 2.3A 124.2W 200mVpp 49 ~ 58V 1.1 ~ 2.3A UL8750 (type HL ), CSA C22.2 No. 250.008, ENEC, TUV EN613471, EN61347213 independent; GB19510.1,GB19510.14, SAFETY STANDARDS Note.8 IP65 or IP67, J613471, J61347213 approved ; design refer to UL609501, TUV EN609501 EMC EMISSION ±0.5% ±0.5%
BLOCK DIAGRAM Fosc : KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT PFC CONTROL O.L.P. O.T.P. POWER SWITCHING PWM CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT O.V.P. V V DIM DIM (B Type) DRIVING METHODS OF LED MODULE This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Vo(%) (A) Constant Voltage area (B) Constant Current region Should there be any compatibility issues, please contact MEAN WELL. 50 Io (%) Typical output current normalized by rated current (%)
DIMMING OPERATION HLG120H DIM(Gray) DIM(Black) V(Blue) V(Brown) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: μa (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) % 90% % 70% 60% 50% 40% 30% 20% 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage DIM Applying additive 10V PWM signal (frequency range Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Output current (%) % 90% % 70% 60% 50% 40% 30% 20% 10% 10% 20% 30% 40% 50% 60% 70% % 90% % Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: V V DIM DIM Additive Resistance Output current (%) % 90% % 70% 60% 50% 40% 30% DO NOT connect "DIM to V" 20% 10% 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N K/N 90K/N K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLG120H BType DIM DIM V() V() Gray Black Blue Brown LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture.
OUTPUT LOAD vs TEMPERATURE 60 60 LOAD (%) 40 20 LOAD (%) 40 20 40 25 10 0 15 30 50 60 70 (HORIZONTAL) 40 25 0 20 45 55 65 75 (HORIZONTAL) AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTICS POWER FACTOR(PF) CHARACTERISTIC Tcase at 70 Constant Current Mode LOAD (%) 90 70 60 50 40 90 125 135 145 155 165 175 1 200 230 305 INPUT VOLTAGE (V) 60Hz PF 1.00 0.98 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0. 0.78 50% 60% 70% % 90% % LOAD (120W) 277Vac 230Vac 115Vac Derating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) 48V Model, Tcase at 70 25 20 EFFICIENCY vs LOAD possess superior working efficiency that up to 93.5% can be reached in field applications. 48V Model, Tcase at 70 96 92 THD(%) 15 10 5 115VAC 230VAC 277VAC EFFICIENCY (%) 88 84 76 72 277Vac 230Vac 115Vac 0 50% 60% 70% % 90% % 10% 20% 30% 40% 50% 60% 70% % 90% % LOAD LOAD
LIFE TIME 120 LIFETIME(Kh) 60 40 20 0 20 30 40 50 60 70 Tcase ( )
MECHANICAL SPECIFICATION Blank/DType Case No.994A Unit:mm 12 9.6 220 196 SJOW 17AWG&H05RNF 1.0mm² 3C AType SJOW 17AWG&H05RNF 1.0mm² 3C 12 9.6 9.4 9.4 34.2 9.4 9.4 34.2 T case tc : Max. Case Temperature 34 tc 220 196 T case 34 tc 98 Vo ADJ. 98 Io ADJ. V(Blue) V(Brown) SJOW 17AWG&H05RNF 1.0mm² 2C ψ4.2 4PL ψ4.2 4PL SJOW 17AWG&H05RNF 1.0mm² 2C 38.8 V(Blue) V(Brown) tc : Max. Case Temperature 38.8 BType 220 12 196 SJOW 17AWG&H05RNF 1.0mm² 3C 9.6 T case tc tc : Max. Case Temperature 38.8 9.4 34.2 9.4 34 98 SJOW 17AWG&H05RNF 1.0mm² 2C SJOW 17AWG&H05RNF 1.0mm² 2C ψ4.2 4PL DIM(Gray) DIM(Black) V(Blue) V(Brown)
WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG120H to operate in dry/wet/damp or outdoor environment. AC source I/P HLG120H O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4PIN 5A/PIN M1204 10A max. 5PIN 5A/PIN M1205 10A max. M15 Order No. Suitable Current 2PIN 12A/PIN M1502 12A max. LED Lamp Cable Joiner 66 26 20 CJ041 suitable for 14AWG~16AWG CJ042 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG120H O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ042. Junction Box Option 196 358 76 10 5 SJTW 18AWG 3C 61 8.5 32 8.5 6 V(Blue) V(Brown) SJOW 17AWG& H05RNF 1.0mm² 2C 2ψ5 3 PF 1/2" 150±20 35 38.8 3 PF 1/2" 150±20 Junction box option is available for A / Blank Type. Please contact MEAW WELL for details. 86 INSTALLATION MANUAL Please refer to : http://www.meanwell.com/manual.html