Service Instructions Syntron Electromagnetic Vibratory Feeder Model: BF-2-B/BF-2-BS BF-2-H/BF-2-HS
Syntron BF-2-B/BF-2-BS BF-2-H/BF-2-HS Electromagnetic Vibratory Feeder SPECIFICATIONS PARTS LIST Thank you for buying your equipment from Syntron Material Handling. This manual will help you to understand how your equipment operates and what is required to maintain peak performance. Please read it thoroughly and keep it on file for reference. Your satisfaction is important to us, so please direct any comments to our Marketing Communications Department. CHECKING THE CURRENT When using an analog clamp on meter to read the current of the feeder, the meter reading must always be multiplied by a value of.7 due to the wave characteristics of the feeder when operating. When using a true RMS meter, the current is as indicated. All current readings must be taken at the control. OPERATING SPECIFICATIONS BF-2-B/BF-2-BS BF-2-H/BF-2-HS Maximum Trough Weight: 20 lbs (9 kg) 20 lbs(9 kg) Minimum Trough Weight: 2 lbs (5.44 kg) 2 lbs (5.44 kg) Trough Stroke Range: 5 20 lb trough-.055 to.060 inches (.4 to.5 mm) 2 20 lb trough -.085 to.090 inches (2.6 to 2.29 mm) 2 4 lb trough-.070 inches (.78mm) * Natural Frequency: 3900 Vpm Minimum (60 Hz) 3580 Vpm Maximum (60 Hz) ** Maximum Current Rating: (Nameplate) 3250 Vpm Minimum (50 Hz) 4.5 Amps (5V/50/60 Hz) 2.25 Amps (230V/50/60 Hz).3 Amps (460V/50/60 Hz) 2980 Vpm Maximum (50 Hz) 4.5 Amps (5V/50/60 Hz) 2.25 Amps (230V/50/60 Hz).3 Amps (460V/50/60 Hz) *Natural frequency is adjusted by changint the quantity/thickness of leaf springs. The quantity/thickness of the springs required is determined by the trough weight (see Tables on pgs. 4 through 7). **Refer to the instructions above. TORQUE SPECIFICATIONS ITEM A,J,K,X BB LUBRICATED/PLATED 35 in-lb (35.6 Nm) 225 in-lb (25.4 Nm)
PARTS LIST BF-2-A & BF-2-AS ELECTROMAGNETIC FEEDERS ITEM DESCRIPTION A Back Plate...52538 Cap Screw, Hex Hd., Zn. Pl. (3/8-6 x )...H0344424 Cap Screw, Hex Hd., S.S. (3/8-6 x )...H030203 Magnet & Cable Assembly (5V/60 Hz)...6076-BG Magnet & Cable Assembly (230V/60 Hz)...6076-BH Magnet & Cable Assembly (460V/60 Hz)...6076-BJ Magnet & Cable Assembly (5V/50 Hz)...6076-BK Magnet & Cable Assembly (230V/50 Hz)...6076-BL Magnet & Cable Assembly (460V/50 Hz)...6076-BM Gasket...650-044-00 ** Nameplate...062245 Armature & Base Assembly...5905-A Belleville Spring Washer...003X25 B C D E F PART NO QTY 4 Only Only 3 PARTS LISTS (cont d) ITEM DESCRIPTION...PART NO Qty. G Trough Mounting Bracket...650-028-00 2
H Air Gap Adjustment Screw (Zinc Pl)...H040440 ] Air Gap Adjustment Screw (S.S.)...H043202 ] Only Plain Washer Zn.Pl. (/2 )...H0730 ] Plain Washer S.S. (/2 )...H07202 ] Only J,K Cap Screw, Hex Hd., Zn.Pl. (3/8-6 x /2 )... H0338824 * Cap Screw Hex Hd., S.S. (3/8-6 x /2 )... H0340926 * M Front Spring Clamp, Zn.Pl..... 5888 4 Front Spring Clamp, S.S.... 224637-00 Only N Front Spring... 3-ply 5884-C0 * Front Spring... -ply 5884-B0 * P Front Spring... 9-ply 5884-A0 * Front Spring Spacer... 5887 2 Q Foot Mounting Bracket... 5875-00 R ** Label (Adjustment)... 95774 S Rubber Foot... 0207X038 4 Rubber Foot (Double Stud)... 0207X035 Only Rubber Foot (Sandwich Type)... 0207X039 Acorn Nut Chr. Pl. (/4-20)... H00607 2 Acorn Nut S.S. (/4-20)... H00502 Only Lock Washer, Zn. Pl. (/4 )... H02809 2 Lock Washer, S.S. (/4 )... H02802 Only T Mach. Screw, Rd. Hd., Br. (#0-32 x 3/8 )... H020302 Lock Washer, Zn. Pl. (#0)... H02409 U Cable Grip... 002X00 V Cable Assembly... 60 Hz 650-027-E Cable Assembly... 50 Hz 650-027-F Only Butt Connector... 0202X002 2 W Rear Spring... -ply 6620-A0 * Rear Spring... 3-ply 6620-B0 * Rear Spring... 9-ply 6620-C0 * X Hex Nut, Zn. Pl. (3/8-6)... H00300 3 Hex Nut, S.S. (3/8-6)... H0580 Only Y Rear Spring Seat & Clamp Bar, Zn.Pl..... 5885 3 Rear Spring Seat & Clamp Bar, S.S.... 224636-00 Only Z Rear Spring Spacer... 5886 8 AA Stud, Zn. Pl.... 5938 3 Stud, S.S.... 224635-00 Only BB Cap Screw, Fl. Hd., Zn.Pl. (5/6-8 x 5/8 )... H04355 4 Cap Screw, Hex Hd., S.S. (5/6-8 x 5/8 )... H0433 Only Sealant... 085X053 As Req d. CC ** Label (Caution)... 25694 * See tables on following pages for quantity ** Do not remove or paint over safety labels or the nameplate. If safety labels need replaced, contact Syntron Material Handling for an additional supply free of charge. 3
FEEDER TUNING Each BF-2 drive is provided with a standard spring arrangment that will be a good starting point for a standard 6 lb pan. Due to minor variations in spring stiffness and trough weights, the quantity of springs may need to be decreased or increased to obtain the correct tuning. The thickness of each spring is determined by the number of plies. Each ply is approximately 0.00 thick. So a 3-ply spring is 0.30 thick. This information is provided as a guide for tuning purposes. Note: These quantities are adjustable and are merely estimates to obtain proper tuning. If the desired stroke is not reached with the given quantities then add or remove springs as needed. Model: BF-2-B (60 Hz) U.S./Canada BF-2-B (60 Hz) Front Spring Quantity Rear Spring Quantity Trough Wt. Front Bolt Rear Bolt (lbs.) 3-ply -ply 9-ply (4 pcs.) 3-ply -ply 9-ply (3pcs.) 2 8 - - 3/8"-6 x /2" - 3-3/8"-6 x /2" 2.5 8 - - 3/8"-6 x /2" 3/8"-6 x /2" 3 8 - - 3/8"-6 x /2" - 3 3/8"-6 x /2" 3.5 8 - - 3/8"-6 x /2" - 3 3/8"-6 x /2" 4 8 - - 3/8"-6 x /2" 2-3/8"-6 x /2" 4.5 8 - - 3/8"-6 x /2" 2 3/8"-6 x /2" * 5 8 - - 3/8"-6 x /2" 2-3/8"-6 x /2" 5.5 6 2-3/8"-6 x /2" 3-3/8"-6 x /2" 6 8 - - 3/8"-6 x /2" 2-2 3/8"-6 x /2" 6.5 8 - - 3/8"-6 x /2" 2 3/8"-6 x /2" 7 8 - - 3/8"-6 x /2" 3 - - 3/8"-6 x /2" 7.5 8 - - 3/8"-6 x /2" 2 2-3/8"-6 x /2" 8 8 - - 3/8"-6 x /2" 3-3/8"-6 x /2" 9 8-2 3/8"-6 x /2" 2 2-3/8"-6 x /2" 20 8 - - 3/8"-6 x /2" 3-3/8"-6 x /2" 2 8-2 3/8"-6 x /2" 3-3/8"-6 x /2" 22 8 - - 3/8"-6 x /2" 4 - - 3/8"-6 x /2" 23 8 - - 3/8"-6 x /2" 4 - - 3/8"-6 x /2" *Standard spring arrangment provided on drive. 4
Model: BF-2-B (50 Hz) U.K/Europe Trough Wt. (lbs.) Front Spring Quantity Rear Spring Quantity Front Bolt Rear Bolt 3-ply -ply 9-ply (4 pcs.) 3-ply -ply 9-ply (3 pcs.) 2 4 - - 3/8"-6 x /4" - 3 3/8"-6 x /2" 2.5 4 - - 3/8"-6 x /4" - 2 3/8"-6 x /2" 3 4 - - 3/8"-6 x /4" - 3-3/8"-6 x /2" 3.5 4 - - 3/8"-6 x /4" 3/8"-6 x /2" 4 4 - - 3/8"-6 x /4" - 3 3/8"-6 x /2" 4.5 4 - - 3/8"-6 x /4" - 3 3/8"-6 x /2" 5 4 - - 3/8"-6 x /4" 2 3/8"-6 x /2" 5.5 4 - - 3/8"-6 x /4" 2-3/8"-6 x /2" 6 4-2 3/8"-6 x /4" - 3 3/8"-6 x /2" 6.5 4 - - 3/8"-6 x /4" 2 3/8"-6 x /2" * 7 4 - - 3/8"-6 x /4" 2-3/8"-6 x /2" 8 4 - - 3/8"-6 x /4" 2-2 3/8"-6 x /2" 8.5 4 - - 3/8"-6 x /4" 3-3/8"-6 x /2" 9 4 - - 3/8"-6 x /4" 2 3/8"-6 x /2" 9.5 4 - - 3/8"-6 x /4" 3 - - 3/8"-6 x /2" 20 6 - - 3/8"-6 x /4" 2 3/8"-6 x /2" 2 4 - - 3/8"-6 x /4" 2 2-3/8"-6 x /2" 22 4 - - 3/8"-6 x /4" 2 2-3/8"-6 x /2" *Standard spring arrangment provided on drive. 5
Model: BF-2-H (60 Hz) U.S./Canada Trough Wt. (lbs.) Front Spring Assembly 3-ply -ply 9-ply Rear Spring Assembly Front Bolt (4 pcs.) 3-ply -ply 9-ply Rear Bolt (3 pcs.) 2 4-2 3/8"-6 x /4" 3/8"-6 x /2" 2.5 4-3/8"-6 x /4" 2-3/8"-6 x /2" 3 4-2 3/8"-6 x /4" 2-3/8"-6 x /2" 3.5 4-2 3/8"-6 x /4" 2 3/8"-6 x /2" 4 4 3/8"-6 x /4" 2-3/8"-6 x /2" 4.5 4 3/8"-6 x /4" 2-3/8"-6 x /2" 5 4 2-3/8"-6 x /4" 2-3/8"-6 x /2" 5.5 4 3/8"-6 x /4" 2-3/8"-6 x /2" * 6 4 2-3/8"-6 x /4" 2-3/8"-6 x /2" 6.5 4 2 3/8"-6 x /4" 2-3/8"-6 x /2" 7 4-3 3/8"-6 x /4" 2 3/8"-6 x /2" 7.5 4 2-3/8"-6 x /4" 2 3/8"-6 x /2" 8 4 2 3 3/8"-6 x /2" 2-3/8"-6 x /2" 9 4 2-3/8"-6 x /4" 2 2-3/8"-6 x /2" 20 4 2 2 3/8"-6 x /2" 3 - - 3/8"-6 x /2" 2 5-3/8"-6 x /4" 3-3/8"-6 x /2" 22 6 - - 3/8"-6 x /4" 3-3/8"-6 x /2" *Standard spring arrangment provided on drive. 6
Model: BF-2-H (50 Hz) U.K./Europe Trough Wt. (lbs.) Front Spring Assembly Rear Spring Assembly Front Bolt Rear Bolt 3-ply -ply 9-ply (4 pcs.) 3-ply -ply 9-ply (3 pcs.) 2-2 5 3/8"-6 x /4" - 2 3/8"-6 x /4" 2.5-4 2 3/8"-6 x /4" - 2 3/8-6 x /4" 3-2 4 3/8"-6 x /4" - 2 3/8"-6 x /2" 3.5-2 4 3/8"-6 x /4" - 3 3/8"-6 x /2" 4-2 4 3/8"-6 x /4" - 2 3/8"-6 x /2" 4.5-4 2 3/8"-6 x /4" - 2 3/8"-6 x /2" 5-2 4 3/8"-6 x /4" - 3-3/8"-6 x /2" 5.5-2 4 3/8"-6 x /4" - 2 2 3/8"-6 x /2" * 6-2 4 3/8"-6 x /4" 3/8"-6 x /2" 6.5-2 4 3/8"-6 x /4" - 3 3/8"-6 x /2" 7-4 2 3/8"-6 x /4" - 3-3/8"-6 x /2" 7.5-2 4 3/8"-6 x /4" - 3 3/8"-6 x /2" 8-4 2 3/8"-6 x /4" 3/8"-6 x /2" 8.5-2 4 3/8"-6 x /4" 2 3/8"-6 x /2" 9-2 4 3/8"-6 x /4" - 4 3/8"-6 x /2" 9.5-4 2 3/8"-6 x /4" 2-3/8"-6 x /2" 20-2 4 3/8"-6 x /4" 2 3/8"-6 x /2" 2-2 4 3/8"-6 x /4" 2 3/8"-6 x /2" *Standard spring arrangment provided on drive. 7
Important Syntron Material Handling reserves the right to alter at any time, without notice and without liability or other obligations on its part, materials, equipment specifications, and models. Syntron Material Handling also reserves the right to discontinue the manufacture of models, parts, and components thereof. Your satisfaction is very important to us. Please direct any comments, questions, or concerns to our Marketing Communications Department. 8
Corporate Office P.O. Box 370 Tupelo, Mississippi 38802 Phone: 662.869.57 Fax: 662.869.7449 Tupelo 2730 Hwy 45 South Saltillo, Mississippi 38866 Phone: 662.869.57 Fax: 662.869.7493 Toll Free: 800.356.4898 info@syntronmh.com Changshu #2 Road No. Changshu Export Processing Zone Changshu, Jiangsu, China 2553 Phone: +86 052.52299002 Fax: +86 052.52297228 info@syntronmh.com Form No. SM0530_2224 Printed in U.S.A