Data Sheet. 71x. MGA Low Noise Amplifier with Mitigated Bypass Switch. Description. Features. Applications

MGA-7154 Low Noise Amplifier with Mitigated Bypass Switch Data Sheet Description Avago s MGA-7154 is an economical, easy-to-use GaAs MMIC Low Noise Amplifier (LNA), which is designed for adaptive CDMA and W-CDMA receiver systems. The MGA- 7154 is part of the Avago Technologies complete CD- MAdvantage RF chipset. The MGA-7154 features a minimum noise figure of.8 db and 16 db available gain from a single stage, feedback FET amplifier. The input and output are partially matched, and only a simple series/shunt inductor match is required to achieve low noise figure and VSWR into 5Ω. When set into the bypass mode, both input and output are internally matched through a mitigative circuit. This circuit draws no current, yet duplicates the in and out impedance of the LNA. This allows the system user to have minimum mismatch change from LNA to bypass mode, which is very important when the MGA-7154 is used between duplexers and/or filters. The MGA-7154 offers an integrated solution of LNA with adjustable IIP. The IIP can be fixed to a desired current level for the receiver s linearity requirements. The LNA has a bypass switch function, which provides low insertion loss at zero current. The bypass mode also boosts dynamic range when high level signal is being received. The MGA-7154 is designed for CDMA and W-CDMA receiver systems. The IP, Gain, and mitigative network are tailored to these applications where filters are used. Many CDMA systems operate 2% LNA mode, 8% bypass. With the bypass current draw of zero and LNA of 1 ma, the MGA-7154 allows an average 2 ma current. The MGA-7154 is a GaAs MMIC, processed on Avago s cost effective PHEMT (Pseudomorphic High Electron Mobility Transistor Technology). It is housed in the SOT4 (SC7 4-lead) package. Features Lead-free Option Available Operating frequency:.1 GHz ~ 6. GHz Noise figure:.8 db (NFmin) Gain: 16 db Average Idd = 2mA in CDMA handset Bypass switch on chip Loss = -5.6 db (Id < 5 μa) IIP = +5 dbm Adjustable input IP: to +9 dbm 2.7 V to 4.2V operation Applications CDMA (IS-95, J-STD-8) Receiver LNA Transmit Driver Amp W-CDMA Receiver LNA TDMA (IS-16) handsets Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model (Class A) ESD Human Body Model (Class ) Refer to Avago Application Note A4R: Electrostatic Discharge Damage and Control. Surface Mount Package SOT-4 /4-lead SC7 Pin Connections and Package Marking INPUT & V ref RF Gnd & V s 4 71x 1 2 RF Gnd & V s OUTPUT & V d 71= Unit marking x = Date Code marking

Functional Block Diagram Simplified Schematic + + Input Evaluation Test Circuit (single positive bias) 1.5 nh RF IN RF OUT Input & V ref Control Output & V d 2.7 nh 71 Output Switch & Bias RF Gnd Gain FET RF Gnd & Vs R bias control V d MGA-7154 Absolute Maximum Ratings [1] Symbol Parameter Units Absolute Operation Maximum Maximum V d Maximum Input to Output Voltage [4] V 5.5 4.2 V c Maximum Input to Ground DC Voltage [4] V +. +.1-5.5-4.2 I d Supply Current ma 6 5 P d Power Dissipation [2] mw 24 2 P in CW RF Input Power dbm +15 +1 T j Junction Temperature C 17 15 T STG Storage Temperature C -65 to +15-4 to +85 [2, ] Thermal Resistance: θ jc = 24 C/W Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage. 2. Ground lead temperature at 25 C.. Thermal resistance measured by 15 C Liquid Crystal Measurement method. 4. Maximum rating assumes other parameters are at DC quiescent conditions. Product Consistency Distribution Charts [5,6] 15 12 Cpk = 2. Std =.24 15 12 Cpk = 1.16 Std =.96 15 12 Cpk = 2. Std =.2 FREQUENCY 9 6 - Std + Std FREQUENCY 9 6 - Std + Std FREQUENCY 9 6 - Std + Std 14.4 15.4 16.4 17.4 GAIN (db) Figure 1. Gain @ 2 GHz, V, 1 ma. LSL = 14.4, Nominal = 15.9, USL = 17.4 1 2 4 5 6 7 8 IIP (dbm) Figure 2. IIP @ 2 GHz, V, 1 ma. LSL = 1., Nominal =., USL = 8..85.95 1.5 1.15 1.25 1.5 1.45 NF (db) Figure. NF @ 2 GHz, V, 1 ma. LSL =.85, Nominal = 1.8, USL = 1.45 Notes: 5. Distribution data sample size is 45 samples taken from 9 different wafers. Future wafers allocated to this product may have nominal values anywhere within the upper and lower specification limits. 6. Measurements made on production test board, Figure 4. This circuit represents a trade-off between an optimal noise match and a realizable match based on production test requirements at 1 ma bias current. Excess circuit losses have been de-embedded from actual measurements. Performance may be optimized for different bias conditions and applications. Consult Application Note for details. 2

MGA-7154 Electrical Specifications T c = +25 C, Z o = 5Ω, I d = 1 ma, V d = V, unless noted Symbol Parameter and Test Condition Units Min. Typ. Max. σ [1] Vref test Vds = 2.4V I d = 1 ma V -.86 -.65 -.4.41 NF test f = 2.1 GHz V d =.V (= Vds - Vref) I d = 1 ma db 1.1 1.45.2 Gain test f = 2.1 GHz V d =.V (= Vds - Vref) I d = 1 ma db 14.4 15.9 17.4.24 IIP test f = 2.1 GHz V d =.V (= Vds - Vref) I d = 1 ma dbm 1..96 Gain, Bypass f = 2.1 GHz Vds = V, Vref = - V I d = ma db -6.4-5.6.12 Bypass Mode [6] Ig test Bypass Mode Vds = V, Vref = - V [6] I d = ma µa 2. 1.5 NFmin [] Minimum Noise Figure f =.9 GHz db.7 As measured in Figure 5 Test Circuit f = 1.5 GHz.7 (Γopt computed from s-parameter and f = 1.9 GHz.8 noise parameter performance as measured f = 2.1 GHz.8 in a 5Ω impedance fixture) f = 2.5 GHz.8 f = 6. GHz 1.1 Ga [] Associated Gain at Nfo f =.9 GHz db 17.1 As measured in Figure 5 Test Circuit f = 1.5 GHz 16.4 (Gopt computed from s-parameter and f = 1.9 GHz 15.8 noise parameter performance as measured f = 2.1 GHz 15.4 in a 5Ω impedance fixture) f = 2.5 GHz 14.9 f = 6. GHz 1. P1dB Output Power at 1 db Gain Compression I d = 6 ma dbm +. As measured in Evaluation Test Circuit with I d = 1 ma +7.4 source resistor biasing [4,5] I d = 2 ma +1.1 Frequency = 2.1 GHz I d = 4 ma +15.5 IIP Input Third Order Intercept Point I d = 6 ma dbm -.5 As measured in Figure 4 Test Circuit [5] I d = 1 ma +. Frequencies = 2.1 GHz, 2.2 GHz I d = 2 ma +7.4 I d = 4 ma +8.7 Switch Bypass Switch Rise/Fall Time (1% - 9%) Intrinsic 1 As measured in Evaluation Test Circuit Eval Circuit ns 1 RLin Input Return Loss as measured in Fig. 4 f = 2.1 GHz db 6..1 RLout Output Return Loss as measured in Fig. 4 f = 2.1 GHz db 1.9.65 ISOL Isolation s12 2 as measured in Fig. 5 f = 2.1 GHz db -22.5 Notes: 1. Standard Deviation and Typical Data based at least 45 part sample size from 9 wafers. Future wafers allocated to this product may have nominal values anywhere within the upper and lower spec limits. 2. Measurements made on a fixed tuned production test circuit (Figure 4) that represents a trade-off between optimal noise match, maximum gain match, and a realizable match based on production test board requirements at 1 ma bias current. Excess circuit losses have been de-embedded from actual measurements. Vd=Vds-Vref where Vds is adjusted to maintain a constant Vd bias equivalent to a single supply V bias application. Consult Applications Note for circuit biasing options.. Minimum Noise Figure and Associated Gain data computed from s-parameter and noise parameter data measured in a 5Ω system using ATN NP5 test system. Data based on 1 typical parts from 9 wafers. Associated Gain is the gain when the product input is matched for minimum Noise Figure. 4. P1dB measurements were performed in the evaluation circuit with source resistance biasing. As P1dB is approached, the drain current is maintained near the quiescent value by the feedback effect of the source resistor in the evaluation circuit. Consult Applications Note for circuit biasing options. 5. Measurements made on a fixed tuned production test circuit that represents a trade-off between optimal noise match, maximum gain match, and a realizable match based on production test board requirements at 1 ma bias current. Performance may be optimized for different bias conditions and applications. Consult Applications Note. 6. The Bypass Mode test conditions are required only for the production test circuit (Figure 4) using the gate bias method. In the preferred source resistor bias configuration, the Bypass Mode is engaged by presenting a DC open circuit instead of the bias resistor on Pin 4.

MGA-7154 Typical Performance T c = 25 C, Z o = 5, V d = V, I d = 1 ma unless stated otherwise. Data vs. frequency was measured in Figure 5 test system and was optimized for each frequency with external tuners. 96 pf RF Input 56 pf 1.5 nh 1 2.7 nh.9 nh V ref 71 56 pf V ds RF Output RF Input Vref Bias Tee Test Fixture 71 Bias Tee Vds RF Output 4 Figure 4. MGA-7154 Production Test Circuit. 2 56 pf Figure 5. MGA-7154 Test Circuit for S, Noise, and Power Parameters over Frequency. 1.5 2 18 NOISE FIGURE (db) 1. 1.1.9.7 2.7V.V.V.5 1 2 4 5 6 FREQUENCY (GHz) Figure 6. Minimum Noise Figure vs. Frequency and Voltage. ASSOCIATED GAIN (db) 17 14 11 8 2.7V.V.V 5 1 2 4 5 6 FREQUENCY (GHz) Figure 7. Associated Gain with Fmin vs. Frequency and Voltage. INPUT IP (dbm) 15 12 9 6-1 2 4 5 6 FREQUENCY (GHz) 2.7V.V.V Figure 8. Input Third Order Intercept Point vs. Frequency and Voltage. ASSOCIATED GAIN (db) 2 17 14 11 8-4 C +25 C +85 C INPUT IP (dbm) 18 15 12 9 6-4 C +25 C +85 C m2 m1 m 5 1 2 4 5 6 FREQUENCY (GHz) Figure 9. Associated Gain with Fmin vs. Frequency. - 1 2 4 5 6 FREQUENCY (GHz) Figure 1. Input Third Order Intercept Point vs. Frequency and Temperature. 5 MHz to 6 GHz Figure 11. S11 Impedance vs. Frequency. (m1 = Sw, m2 = 6 ma, m = 1 ma) 18 4 m 5 MHz to 6 GHz m2 m1 Figure 12. S22 Impedance vs. Frequency. (m1 = Sw, m2 = 6 ma, m = 1 ma) INSERTION LOSS (db) -2-4 -6-8 2.7V G ass w/fmin.v Minimum.V -1-1 2 4 5 6 1 2 4 5 6 FREQUENCY (GHz) FREQUENCY (GHz) Figure 1. Bypass Mode Associated Insertion Loss with Fmin Match and Minimum Loss vs. Frequency. OP1dB (dbm) 15 12 9 6 Figure 14. Output Power at 1 db Compression vs. Frequency and Voltage. [4]

MGA-7154 Typical Performance, continued T c = 25 C, Z o = 5, V d = V, I d = 1 ma unless stated otherwise. Data vs. frequency was measured in Figure 5 test system and was optimized for each frequency with external tuners. 18 18 18 15 15 15 INPUT IP (dbm) 12 9 6 OP1dB (dbm) 12 9-6 OP1dB (dbm) 12 9 6 6 ma 1 ma 2 ma -4 C +25 C +85 C -4 C +25 C +85 C NF (db) - 1 2 4 5 6 FREQUENCY (GHz) Figure 15. Input Third Order Intercept Point vs. Frequency and Current. 2.2 2. 1.8 1.6 1.4 1.2 1..8.6.4.2 1 2 4 Id CURRENT (ma) Figure 18. Minimum Noise Figure vs. Current (2 GHz). - 1 2 4 I dsq CURRENT (ma) Figure 16. Output Power at 1 db Compression vs. I dsq Current and Temperature (Passive Bias, V ref Fixed) [4]. GAIN (db) 2 17 14 11 8 5-4 C +25 C +85 C 2 1 2 4 Id CURRENT (ma) Figure 19. Gain vs. Current and Temperature (2 GHz). - 1 2 4 I d CURRENT (ma) Figure 17. Output Power at 1 db Compression vs. Current and Temperature (Source Resistor Bias in Evaluation Circuit) [5]. INPUT IP (dbm) 12 9 6-1 2 4 Id CURRENT (ma) -4 C +25 C +85 C Figure 2. Input Third Intercept Point vs. Current and Temperature (2 GHz). 1..8 Vs (V).6.4.2 1 2 4 Id CURRENT (ma) Figure 21. Control Voltage vs. Current. 5 Notes: 4. P1dB measurements were performed with passive biasing in Production Test Circuit (Figure 4.). Quiescent drain current, Idsq, is set by a fixed Vref with no RF drive applied. As P1dB is approached, the drain current may increase or decrease depending on frequency and DC bias point which typically results in higher P1dB than if the drain current is maintained constant by active biasing. 5. P1dB measurements were performed in Evaluation Test Circuit with source resistor biasing which maintains the drain current near the quiescent value under large signal conditions.

MGA-7154 Typical Scattering Parameters T C = 25 C, V ds = V, V ref = -.V, I d = ma (bypass mode), Z O = 5Ω Freq S 11 S 11 S 21 S 21 S 12 S 12 S 22 S 22 S 21 G max RL in RL out Isolation (GHz) Mag. Ang. Mag. Ang. Mag. Ang. Mag. Ang. (db) (db) (db) (db) (db).1.968-4.5.21 41.1.21 41..96-5.9 -.6-12.5 -. -.6 -.6.2.961-8.4.9 7.5.9 7.8.916-9.5-28.2-9.1 -. -.8-28.2..951-11.4.65 7.7.64 7.9.91-1.1-2.7-6. -.4 -.9-2.9.4.947-14.8.9 7.9.9 71.89-16.5-2.9-4.2 -.5-1. -2.9.5.97-18.1.114 65.7.114 65.9.871-2.2-18.9 -.6 -.6-1.2-18.9.6.929-21..16 61.4.16 61.5.861-2.7-17. -2.8 -.6-1. -17..7.921-24.5.157 57.157 57.1.846-27.1-16.1-2.4 -.7-1.5-16.1.8.91-27.7.176 52.7.176 52.8.8 -. -15.1-2.2 -.8-1.6-15.1.9.95 -.8.194 48.6.194 48.7.82 -. -14.2-2. -.9-1.7-14.2 1.895 -.7.211 44.5.211 44.6.86-6. -1.5-1.9-1. -1.9-1.5 1.1.887-6.6.226 4.6.226 4.6.791-9.2-12.9-1.9-1. -2. -12.9 1.2.878-9.4.29 6.8.29 6.9.776-41.9-12.4-2. -1.1-2.2-12.4 1..869-42.1.252.2.252..762-44.4-12. -2.1-1.2-2.4-12. 1.4.862-44.7.264 29.7.26 29.8.748-46.9-11.6-2.1-1. -2.5-11.6 1.5.854-47..274 26..274 26.4.72-49.2-11.2-2.2-1.4-2.7-11.2 1.6.847-49.8.28 2.1.28 2.2.719-51.4-11. -2. -1.4-2.9-11. 1.7.89-52.4.29 19.9.292 2.75-5.5-1.7-2.4-1.5 -. -1.7 1.8.82-54.8. 16.8. 16.9.692-55.5-1.5-2.5-1.6 -.2-1.5 1.9.825-57.1.8 1.8.7 14.679-57.6-1.2-2.6-1.7 -.4-1. 2.819-59.5.14 11.14 11.1.665-59.4-1.1-2.7-1.7 -.5-1.1 2.1.812-61.7.21 8.1.2 8.2.65-61.2-9.9-2.8-1.8 -.7-9.9 2.2.86-6.9.26 5..26 5.4.69-6 -9.7-2.9-1.9 -.9-9.7 2..8-66..1 2.6.1 2.7.627-64.6-9.6 -. -1.9-4.1-9.6 2.4.792-68.5.6.6.1.616-66. -9.5 -.1-2. -4.2-9.5 2.5.787-7.9.41-2.7.4-2.5.6-67.8-9. -.2-2.1-4.4-9.4.76-81.8.59-15.1.58-15.548-75.5-8.9 -.6-2.4-5.2-8.9.5.74-9.4.71-27.1.7-27.497-8.4-8.6 -.9-2.6-6.1-8.6 4.721-16.77-9.1.77-9.452-91.6-8.5-4. -2.8-6.9-8.5 4.5.78-119.8.79-51.78-5.9.418-1.7-8.4-4.6 -. -7.6-8.5 5.7-14.7.74-6.2.74-6.9-11.7-8.5-4.9 -.1-8.1-8.5 5.5.7-15.2.62-75.2.62-75.1.76-121.1-8.8-5.2 -.1-8.5-8.8 6.699-165.1.47-86.7.47-86.5.61-1.9-9.2-5.7 -.1-8.8-9.2 6.5.75 179.7.28-98.1.28-98.5-141.7-9.7-6.1 -. -9.1-9.7 7.78 165..7-19.4.7-19.4.6-152 -1. -6.7 -. -9.5-1. 8.75 16..262-1.2.262-1.1.292-17.9-11.6-8. -. -1.7-11.6 9.728 16.4.22-157..21-157.2.242 156. -1.9-1.4-2.8-12. -1.9 1.781 75.141 179.6.141 179.8.247 114.9-17. -12.7-2.1-12.1-17. 11.815 48.9.8 156.7.8 156.8.6 8. -21.6-16.5-1.8-1. -21.6 12.88 28.2.4 14.9.4 15.6.67 54.2-29.4-2.5-1.5-8.7-29.4 1.847 8.5.5-22.1.5-19.9.414 29.4-46. -9.7-1.4-7.7-46. 14.85-1.6.7-7.5.6-7.5.478 4.7-28.6-21.9-1.4-6.4-28.9 15.856-28.5.58-94.57-94.1.555-15.7-24.7-17.4-1.4-5.1-24.9 16.848-4.4.72-112..72-112.2.626 -.1-22.9-15.2-1.4-4.1-22.9 17.844-5.9.8-127.4.8-127..669-44 -21.6-1.6-1.5 -.5-21.6 18.87-65.2.88-145.2.88-144.4.76-58.7-21.1-11.9-1.2 -. -21.1 6

MGA-7154 Typical Scattering Parameters and Noise Parameters T C = 25 C, V ds = 2.25 V, V ref = -.77 V, I d = ma, Z O = 5Ω Freq S 11 S 11 S 21 S 21 S 12 S 12 S 22 S 22 S 21 G max RL in RL out Isolation (GHz) Mag. Ang. Mag. Ang. Mag. Ang. Mag. Ang. (db) (db) (db) (db) (db)..927-1.1 2.945 17.7.28 2.9.754-7.9 9.4 21.6 -.7-2.5-1.1.5.921-16.4 2.99 164.1.2 2.9.744-12.6 9.4 21.1 -.7-2.6-29.9.7.915-22.7 2.97 158..9 8.7.742-17.5 9. 2.6 -.8-2.6-28.2.9.99-28.8 2.871 152.6.47 41..74-22.1 9.2 2.2 -.8-2.6-26.6 1.1.899-4.8 2.826 147.54 41.5.76-26.7 9. 19.6 -.9-2.7-25.4 1..891-4.5 2.78 141.5.62 4.5.72 -.9 8.9 19.1-1. -2.7-24.2 1.5.88-46.2 2.728 16..69 8.8.727-4.9 8.7 18.6-1.1-2.8-2.2 1.7.87-51.7 2.69 11.1.76 6.7.721-8.7 8.6 18. -1.2-2.8-22.4 1.9.86-57 2.652 126.1.82 4..716-42.5 8.5 17.5-1. -2.9-21.7 2.858-59.7 2.6 12.7.86.711-44.2 8.4 17.2-1. -. -21. 2.1.852-62. 2.69 121.2.89 1.7.77-46 8. 17. -1.4 -. -21. 2.2.846-64.8 2.59 118.7.92.4.7-47.9 8. 16.7-1.5 -.1-2.7 2..841-67.5 2.579 116..95 28.9.698-49.5 8.2 16.5-1.5 -.1-2.4 2.4.8-7 2.554 11.9.98 27.5.695-51. 8.1 16.2-1.6 -.2-2.2 2.5.828-72.8 2.544 111.5.1 26.1.689-52.9 8.1 15.9-1.6 -.2-2..794-85.6 2.479 99.7.114 18.5.66-61.6 7.9 14.7-2. -.6-18.9.5.758-99.1 2.4 87.7.125 1.7.626-7.5 7.7 1.6-2.4-4.1-18.1 4.717-11.5 2.7 75.6.14 2.1.587-8 7.5 12.5-2.9-4.6-17.5 4.5.679-129 2.2 6.1.141-6.4.549-9. 7. 11.6 -.4-5.2-17. 5.644-145.1 2.252 5.5.144-15.4.511-1.9 7.1 1.7 -.8-5.8-16.8 6.594-176.1 2.7 26.9.14-1.454-12.8 6. 9.2-4.5-6.9-16.9 7.565 155 1.885 4.6.18-45..48-14.1 5.5 8. -5. -7.8-17.2 8.56 127 1.715-16.6.126-58.8.44-157. 4.7 6.7-5.4-9. -18. 9.545 99.4 1.611-7.117-6.7.281-177.8 4.1 6. -5. -11. -18.6 1.68 7.4 1.5-59.7.12-71.8.254 145.5.5 5.8-4. -11.9-18.4 11.665 46.2 1.2-82.12-81.5.274 16.1 2.5 5.4 -.5-11.2-18.4 12.77 27.2 1.167-11.9.119-9.17 75.4 1. 4.8 -. -1. -18.5 1.75 8.7 1. -121.7.12-99.8.56 47.9. 4.2-2.7-9. -18.4 14.76-9.7.94-142.2.122-11.9.421 2.1 -.9.7-2.4-7.5-18. 15.788-27.4.757-162.1.118-122.8.511-4.1-2.4.1-2.1-5.8-18.6 16.82-42.4.69 18.115-14.2.6-21.1-4. 2.1-1.9-4.4-18.8 17.88-5.1.5 165.7.11-144..65-6.7-6. 1. -1.9 -.7-18.9 18.845-64.7.429 15.7.11-157.8.699-52.6-7.4 1. -1.5 -.1-19.2 Freq Fmin GAMMA OPT Rn/5 Ga (GHz) (db) Mag Ang (db).7.88.61 16..45 14.8.9.87.64 22.4.4 14.8 1.1.9.65 28.4.44 14.7 1..92.6.5.4 14.2 1.5.95.64 7.2.42 14.2 1.7.95.6 4.2.41 14 1.9.99.62 45.4.4 1.7 2 1.62 47.6.4 1.6 2.1 1.2.61 49.2.4 1.4 2.2 1..6 5.9.9 1.4 2. 1..62 5.9.8 1.2 2.4 1.4.6 55.4.7 12.9 2.5 1.4.61 57.6.7 12.9 1.8.58 67.9. 12.1 5 1.21.49 12.14 9.6 6 1.6.46 151.2.8 8.4 7

MGA-7154 Typical Scattering Parameters and Noise Parameters T C = 25 C, V ds = 2. V, V ref = -.7 V, I d = 6 ma, Z O = 5Ω Freq S 11 S 11 S 21 S 21 S 12 S 12 S 22 S 22 S 21 G max RL in RL out Isolation (GHz) Mag. Ang. Mag. Ang. Mag. Ang. Mag. Ang. (db) (db) (db) (db) (db)..911-11 4.164 17.2.26 2.5.667-8.4 12.4 22.6 -.8 -.5-1.7.5.94-17.7 4.148 16.. 2.6.658-1.4 12.4 22.2 -.9 -.6 -.5.7.896-24.5 4.94 157.1.6 8.5.656-18.5 12.2 21.7-1. -.7-28.9.9.887-1.2 4.29 151.1.4 41.654-2.5 12.1 21.2-1. -.7-27. 1.1.875-7.5.95 145.2.5 41..648-28.2 11.9 2.6-1.2 -.8-26. 1..864-4.7.877 19.5.57 4.4.64-2.6 11.8 2. -1. -.8-24.9 1.5.85-49.7.791 14.6 8.8.68-6.8 11.6 19.5-1.4 -.9-24. 1.7.84-55.6.72 128.7.69 6.7.61-4.7 11.4 18.9-1.5-4. -2.2 1.9.826-61.2.649 12.4.75 4.5.624-44.6 11.2 18.4-1.7-4.1-22.5 2.82-64.611 121.78..619-46.4 11.2 18.1-1.7-4.2-22.2 2.1.812-66.7.576 118.4.81 2.1.615-48.2 11.1 17.8-1.8-4.2-21.8 2.2.86-69.4.55 115.7.84.7.69-5.1 11. 17.6-1.9-4. -21.5 2..797-72..511 11..86 29.4.64-51.7 1.9 17. -2. -4.4-21. 2.4.787-74.9.474 11.9.89 28.1.6-5.5 1.8 16.9-2.1-4.4-21. 2.5.78-77.8.446 18..91 26.7.59-55.1 1.7 16.7-2.2-4.5-2.8.78-91.2.9 96..12 19.7.561-6.7 1.4 15.5-2.6-5. -19.8.5.695-15.2.19 84.2.112 12.6.52-72.6 1.1 14. -.2-5.6-19. 4.649-12.2.72 72.2.119 4.9.482-82 9.7 1. -.8-6. -18.5 4.5.69-16.2 2.962 59.9.125-2.6.44-92. 9.4 12.4-4. -7.1-18.1 5.57-152.7 2.8 47.8.128-1.4.46-1 9. 11.5-4.8-7.8-17.9 6.529 175.9 2.555 25.1-2.6.52-12 8.1 1.1-5.5-9.1-17.7 7.57 147.2 2.295.6.129-6.8-142.4 7.2 8.9-5.9-1.2-17.8 8.485 119.4 2.72-16.8.12-47.7.247-159.2 6. 7.8-6. -12.1-18.2 9.52 92.5 1.922-6.5.12-52.7.189 178.9 5.7 7.1-6. -14.5-18.2 1.574 65 1.78-58..12-6.1.174 12.2 5. 6.9-4.8-15.2-17.6 11.69 42.1 1.576-79.6.14-75.218 88.5 4. 6.4 -.9-1.2-17.5 12.686 2.9 1.88-98.8.16-85.8.272 59.8 2.8 5.9 -. -11. -17. 1.715 5.8 1.26-118.1.17-97.7.18 4.5 1.8 5.4-2.9-1. -17. 14.741-12 1.94-18.4.17-11.5.88 9..8 4.9-2.6-8.2-17. 15.774-29.2.926-158.11-12..482-11.4 -.7 4.4-2.2-6. -17.7 16.789-4.9.761-175.8.125-15.2.57-26. -2.4.6-2.1-4.9-18.1 17.797-54..64 169.4.121-145.5.622-4.6-4. 2.5-2. -4.1-18. 18.8-65.8.549 15.8.117-159.67-55.4-5.2 2.5-1.6 -.5-18.6 Freq Fmin GAMMA OPT Rn/5 Ga (GHz) (db) Mag Ang (db).7.71.56 15.7.2 16..9.74.58 21.8. 16. 1.1.76.56 28..1 15.9 1..79.54.8. 15.6 1.5.81.58 6.5.29 15.6 1.7.8.57 4.29 15. 1.9.82.57 45.2.28 15.1 2.8.56 47.8.28 14.9 2.1.85.55 49..28 14.7 2.2.85.58 5.7.27 14.8 2..87.56 5.9.26 14.5 2.4.87.54 55..26 14. 2.5.88.55 57.7.26 14.2.9.5 67.7.2 1.5 5 1..42 12.7.11 1.7 6 1.14.8 152.7.7 9.4 8

MGA-7154 Typical Scattering Parameters and Noise Parameters T C = 25 C, V ds = 2.4 V, V ref = -.6 V, I d = 1 ma, Z O = 5Ω Freq S 11 S 11 S 21 S 21 S 12 S 12 S 22 S 22 S 21 G max RL in RL out Isolation (GHz) Mag. Ang. Mag. Ang. Mag. Ang. Mag. Ang. (db) (db) (db) (db) (db)..9-11.5 5.2 169.8.24 2..68-8.7 14. 2.2 -.9-4. -2.4.5.892-18.6 4.99 162.7.29 2.4.599-1.8 14. 22.8-1. -4.5 -.8.7.884-25.7 4.919 156..4 8..597-19.1 1.8 22.4-1.1-4.5-29.4.9.87-2.7 4.8 15.41 4.9.595-24.2 1.7 21.8-1.2-4.5-27.7 1.1.859-9.4 4.728 14.9.47 41..589-29.1 1.5 21.2-1. -4.6-26.6 1..845-45.8 4.62 18.5 4.5.584 -.6 1. 2.5-1.5-4.7-25.5 1.5.82-52 4.59 12.4.59 9.1.578-7.8 1.1 2. -1.6-4.8-24.6 1.7.816-58.1 4.412 126.9.65 7.2.571-41.8 12.9 19.4-1.8-4.9-2.7 1.9.81-6.9 4.12 121.5.7 5.56-45.7 12.7 18.8-1.9-5. -2.1 2.79-66.8 4.259 119.7.9.558-47.4 12.6 18.5-2. -5.1-22.7 2.1.784-69.6 4.211 116.4.75 2.7.55-49.2 12.5 18.2-2.1-5.1-22.5 2.2.776-72.4 4.171 11.7.78 1.6.549-51 12.4 18. -2.2-5.2-22.2 2..767-75. 4.117 111.2.8..54-52.7 12. 17.7-2. -5. -21.9 2.4.757-78 4.7 18.7.8 29.58-54.5 12.2 17.4-2.4-5.4-21.6 2.5.749-8.9 4.29 16.2.85 27.7.51-56 12.1 17.1-2.5-5.5-21.4.71-94.7.829 94.95 21.2.499-64.4 11.7 15.8 -.1-6. -2.4.5.655-18.9.659 81.9.1 14.7.461-7.1 11. 14.7 -.7-6.7-19.7 4.67-124.2.49 7.11 7.6.42-82.2 1.9 1.7-4. -7.5-19.2 4.5.567-14.4.5 58.116.8.82-92.6 1.5 12.8-4.9-8.4-18.7 5.5-157.2.16 46.1.12-6..46-1. 1. 12. -5.5-9.2-18.4 6.49 171. 2.828 2.9.124-18..296-12.4 9. 1.6-6.1-1.6-18.1 7.476 142.7 2.526 2.9.126 -.1.255-14.1 8. 9.5-6.4-11.9-18. 8.458 115.1 2.271-17.124-41.4.195-159.7 7.1 8. -6.8-14.2-18.1 9.48 88.8 2.94-6..128-47..141 176.8 6.4 7.6-6.4-17. -17.9 1.558 62.2 1.95-57.6.19-58.9.14 12.6 5.7 7.4-5.1-17.1-17.1 11.627 9.9 1.712-78..142-71.7.2 76.5 4.7 7. -4.1-14. -17. 12.675 22.1 1.512-97.2.145-8.5.26 5.1.6 6.5 -.4-11.7-16.8 1.76 4.4 1.51-116.2.145-96..8 26.4 2.6 6. -. -1.2-16.8 14.72-1. 1.2-16.2.145-19.7.79.1 1.6 5.6-2.7-8.4-16.8 15.767 -.2 1.22-155.6.17-12.1.47-15.8.2 5.1-2. -6.5-17. 16.78-44.7.849-17..11-15.2.558-29.5-1.4 4. -2.1-5.1-17.7 17.792-55.1.71 171.8.126-145.7.69-4 -2.9.4-2. -4. -18. 18.828-66.5.622 156.122-159.2.656-57. -4.1. -1.6 -.7-18. Freq Fmin GAMMA OPT Rn/5 Ga (GHz) (db) Mag Ang (db).7.6.5 15..27 17.2.9.66.54 21.4.26 17.1 1.1.68.55 28.5.26 16.9 1..7.52.8.25 16.5 1.5.72.55 7.25 16.4 1.7.72.56 9.9.25 16.2 1.9.7.5 45.5.24 15.8 2.74.5 48..2 15.6 2.1.76.52 49.6.2 15.4 2.2.78.54 5.7.2 15.4 2..78.5 54.22 15.2 2.4.79.51 55.6.22 15 2.5.8.52 57.6.22 14.9.82.5 67.5.2 14.2 5.94.8 121..1 11.2 6 1.5.4 155.7 1 9

MGA-7154 Typical Scattering Parameters and Noise Parameters T C = 25 C, V ds = 2.5 V, V ref = -.5 V, I d = 2 ma, Z O = 5Ω Freq S 11 S 11 S 21 S 21 S 12 S 12 S 22 S 22 S 21 G max RL in RL out Isolation (GHz) Mag. Ang. Mag. Ang. Mag. Ang. Mag. Ang. (db) (db) (db) (db) (db)..889-12.1 5.952 169..2 22.8.541-9 15.5 2.8-1. -5. -2.8.5.88-19.5 5.91 162.27 2.52-14.1 15.4 2. -1.1-5.5-1.4.7.87-27 5.8 155..2 8.2.51-19.6 15. 22.9-1.2-5.5-29.9.9.858-4. 5.684 148.8.7 4.9.528-24.7 15.1 22. -1. -5.5-28.6 1.1.842-41.2 5.548 142.5.4 41.5.52-29.7 14.9 21.6-1.5-5.6-27. 1..826-47.9 5.47 16.5.49 4.9.518-4.2 14.7 21. -1.7-5.7-26.2 1.5.81-54. 5.26 1.6.55 9.6.511-8.4 14.4 2.4-1.8-5.8-25.2 1.7.792-6.7 5.126 125.6 8.55-42.4 14.2 19.8-2. -5.9-24.4 1.9.774-66.6 4.99 119.5.65 6.1.497-46.2 14. 19.2-2.2-6.1-2.7 2.765-69.6 4.922 116.9.67 5.49-47.9 1.8 18.9-2. -6.1-2.5 2.1.755-72.5 4.857 114..69 4.488-49.6 1.7 18.6-2.4-6.2-2.2 2.2.746-75.4 4.797 111.5.72 2.9.48-51.5 1.6 18. -2.5-6. -22.9 2..76-78. 4.729 19.74 1.8.477-5 1.5 18. -2.7-6.4-22.6 2.4.724-81 4.668 16.5.76.6.47-54.7 1.4 17.7-2.8-6.5-22.4 2.5.716-84 4.612 1.9.78 29.4.467-56.2 1. 17.5-2.9-6.6-22.2.664-98 4.4 91.7.87 2.6.45-64.1 12.7 16.2 -.6-7.2-21.2.5.616-112.4 4.17 79.7.95 17.8.99-72.4 12. 15.1-4.2-8. -2.4 4.566-128.886 67.9.12 11..6-81.1 11.8 14.1-4.9-8.9-19.8 4.5.528-144.5.686 56.1.18 5.1.24-91.4 11. 1.2-5.5-9.8-19. 5.495-161.5.47 44.5.11-1..291-12.1 1.8 12.4-6.1-1.7-18.9 6.46 166.9.78 22.8.119-12.5.245-122. 9.8 11.1-6.7-12.2-18.5 7.448 18.5 2.77 2.4.124-24.1.28-142.5 8.7 9.9-7. -1.6-18.1 8.46 111.1 2.452-17.1.125-5..15-158.6 7.8 8.8-7.2-16.5-18.1 9.462 85.4 2.252-6.1-42.2.99 175.9 7.1 8.1-6.7-2.1-17.5 1.544 59.7 2.75-56.8.146-54.9.114 16.8 6. 7.9-5. -18.9-16.7 11.617 8.1 1.86-77.2.15-68.5.191 65. 5. 7.5-4.2-14.4-16.5 12.668 2.6 1.626-95.6.15-81.256 41.5 4.2 7.1 -.5-11.8-16. 1.7.1 1.457-114.4.15-94.4.5 19.4. 6.6 -.1-1. -16. 14.728-14.4 1.299-14.1.15-18.4.77-2.4 2. 6.2-2.8-8.5-16. 15.76-1.2 1.111-15..144-122.2.469-19.6.9 5.8-2. -6.6-16.8 16.78-45.5.9-17.8.17-14.6.552-2.5 -.6 5. -2.2-5.2-17. 17.789-55.8.788 174.2.12-145..599-45.4-2.1 4.1-2.1-4.5-17.6 18.825-67.1.691 158..126-159.645-59 -.2 4.1-1.7 -.8-18. Freq Fmin GAMMA OPT Rn/5 Ga (GHz) (db) Mag Ang (db).7.59.52 15.7.25 18.1.9.64.5 21.7.24 17.9 1.1.66.5 28.9.24 17.7 1..68.51 4.2.2 17. 1.5.68.54 8.5.2 17.2 1.7.69.54 4.8.2 17 1.9.72.51 46.4.22 16.5 2.7.51 48.8.22 16.4 2.1.74.5 5.5.21 16.2 2.2.75.51 52.4.21 16.1 2..76.51 55.4.2 15.9 2.4.77.48 56..2 15.6 2.5.79.5 59.2 15.6.82.47 68.6.18 14.7 5.9.4 125.1.9 11.7 6 1.6.1 16.6.7 1.5 1

MGA-7154 Typical Scattering Parameters and Noise Parameters T C = 25 C, V ds = 2.7 V, V ref = -. V, I d = 4 ma, Z O = 5Ω Freq S 11 S 11 S 21 S 21 S 12 S 12 S 22 S 22 S 21 G max RL in RL out Isolation (GHz) Mag. Ang. Mag. Ang. Mag. Ang. Mag. Ang. (db) (db) (db) (db) (db)..889-12. 6.174 169.2.22 22..58-8.9 15.8 2.9-1. -5.9 -.2.5.88-19.8 6.117 161.8.25 1.6.51-1.7 15.7 2.5-1.1-6. -2..7.87-27.4 6.12 155.1.29 7.9.499-19.1 15.6 2. -1.2-6. -.8.9.857-4.9 5.885 148.5.5 4.9.497-24.2 15.4 22.4-1. -6.1-29.1 1.1.841-41.9 5.74 142.1.4 41.7.49-29 15.2 21.7-1.5-6.1-28. 1..82-48.7 5.589 16.46 41.4.488 -.4 14.9 21. -1.7-6.2-26.7 1.5.87-55.2 5.45 1.2.51 4.2.48-7.5 14.7 2.4-1.9-6. -25.8 1.7.788-61.6 5.289 124.5.55 8.7.477-41. 14.5 19.8-2.1-6.4-25.2 1.9.769-67.6 5.145 119.6 7.47-45 14.2 19.2-2. -6.6-24.4 2.76-7.6 5.72 116..62 6.1.466-46.5 14.1 18.9-2.4-6.6-24.2 2.1.75-7.5 5. 11.7.64 5.1.462-48.2 14. 18.6-2.5-6.7-2.9 2.2.79-76. 4.9 111.66 4.2.458-5 1.9 18. -2.6-6.8-2.6 2..7-79.4 4.865 18.4.68.1.452-51.4 1.7 18. -2.7-6.9-2. 2.4.718-82.2 4.81 15.9.7 2.448-5 1.6 17.7-2.9-7. -2.1 2.5.79-85.2 4.79 1..72.9.442-54.5 1.5 17.5 -. -7.1-22.9.656-99. 4.447 91.81 25.5.41-61.9 1. 16.2 -.7-7.7-21.8.5.68-11.8 4.197 79.89 2.8-69.7 12.5 15.1-4. -8.4-21. 4.559-129.5.96 67..95 14.44-77.9 12. 14.1-5.1-9. -2.4 4.5.521-146.751 55.6.11 8.2.1-87.7 11.5 1. -5.7-1.2-19.9 5.49-16.5 44.1.16 2.278-98 11. 12.5-6.2-11.1-19.5 6.457 165.4.124 22.5.114-8.6.26-117.5 9.9 11.2-6.8-12.5-18.9 7.447 17.1 2.776 2.2.12-19.8.21-17.1 8.9 1. -7. -1.9-18.4 8.46 19.8 2.484-17.2.122 -.9.146-151.4 7.9 8.9-7.2-16.7-18. 9.462 84.5 2.28-6.12-7.8.96-17.8 7.2 8.2-6.7-2.4-17.6 1.546 59.1 2.12-56.7.146-5.8.11 112 6.5 8. -5. -19.9-16.7 11.621 7.8 1.861-77.152-64.7.177 66.8 5.4 7.6-4.1-15. -16.4 12.672 2. 1.649-95.4.155-77.6.244 42. 4. 7.2 -.5-12. -16.2 1.75 2.9 1.478-114.1.157-91..29 19.8.4 6.8 -. -1.7-16.1 14.7-14.6 1.2-1.9.157-15.8.66-2.2 2.4 6.4-2.7-8.7-16.1 15.768-1. 1.129-15.1.149-119.7.461-19.1 1.1 6. -2. -6.7-16.5 16.786-45.7.946-17.6.141-12.5.545-2.1 -.5 5.2-2.1-5. -17. 17.794-56.1.81 174.5.16-14.6.595-45.1-1.9 4. -2. -4.5-17. 18.8-67.4.7 158.5.11-157.4.641-58.8 -.1 4. -1.6 -.9-17.7 Freq Fmin GAMMA OPT Rn/5 Ga (GHz) (db) Mag Ang (db).7.69.56 17..2 18.5.9.7.57 2.9. 18. 1.1.7.56.8.1 18 1..77.54 6.5. 17.6 1.5.77.58 4.7.29 17.6 1.7.8.57 4.9.29 17. 1.9.8.55 49.7.28 16.9 2.85.54 52.1.27 16.7 2.1.86.54 54..27 16.5 2.2.9.54 55.5.26 16.4 2..91.54 59..26 16.2 2.4.91.52 61.25 16 2.5.9.52 6.2.25 15.8.98.49 74.7.22 15 5 1.19.7 16.1 11.9 6 1.5.5 172.8.8 1.7 11

Part Number Ordering Information Part Number No. of Devices Container MGA-7154-TR1G 7" Reel MGA-7154-TR2G 1 1" Reel MGA-7154-BLKG 1 Antistatic bag Package Dimensions Outline 4 SOT-4 (SC7 4-lead) 1. (.51) BSC Recommended PCB Pad Layout for Avago s SC7 4L/SOT-4 Products 1. (.51) 1. (.9) HE E.6 (.24) 2. (.79) 1.15 (.45) BSC D b1 1.15 (.45).9 (.5) A A2 Dimensions in mm (inches) b A1 L C DIMENSIONS (mm) SYMBOL E D HE A A2 A1 b b1 c L MIN. 1.15 1.85 1.8.8.8..15.55.1.1 MAX. 1.5 2.25 2.4 1.1 1..1.4.7.2.46 NOTES: 1. All dimensions are in mm. 2. Dimensions are inclusive of plating.. Dimensions are exclusive of mold flash & metal burr. 4. All specifications comply to EIAJ SC7. 5. Die is facing up for mold and facing down for trim/form, ie: reverse trim/form. 6. Package surface to be mirror finish. 12

Device Orientation REEL 4 mm CARRIER TAPE 8 mm 71x 71x 71x 71x USER FEED DIRECTION TOP VIEW END VIEW COVER TAPE Tape Dimensions For Outline 4T P Po D P2 E C F W t1 (CARRIER TAPE THICKNESS) D1 Tt (COVER TAPE THICKNESS) 1 MAX. Ko 1 MAX. Ao Bo CAVITY PERFORATION CARRIER TAPE COVER TAPE DISTANCE DESCRIPTION SYMBOL SIZE (mm) SIZE (INCHES) LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER DIAMETER PITCH POSITION WIDTH THICKNESS WIDTH TAPE THICKNESS CAVITY TO PERFORATION (WIDTH DIRECTION) CAVITY TO PERFORATION (LENGTH DIRECTION) Ao Bo Ko P D1 D Po E W t1 C Tt F P2 2.4 ±.1 2.4 ±.1 1.2 ±.1 4. ±.1 1. +.25 1.55 ±.1 4. ±.1 1.75 ±.1 8. +. -.1.254.2 5.4 ±.1.62 ±.1.5 ±.5 2. ±.5.94 ±.4.94 ±.4.47 ±.4.157 ±.4.9 +.1.61 +.2.157 ±.4.69 ±.4.15 +.12.1 ±.8.25 +.4.25 ±.4.18 ±.2.79 ±.2 1

Designing with MGA-7154, a Low Noise Amplifier with Built-in Mitigated Bypass Switches Introduction The MGA-7154 is a single stage GaAs RFIC low noise amplifier with an integrated bypass switch (Figure 1). RF IN Switch & Bias RF OUT Figure 1. MGA-7154 Functional Diagram. This application note describes a low noise amplifier design using Avago Technologies MGA-7154. The MGA-7154 is designed for receivers and transmitters operating from 1 MHz to 6 GHz, mainly for CDMA applications i.e. IS-95 CDMA19, CDMA8 and W-CDMA. It can be used as a first stage (Q1) in a CDMA PCS 19 MHz application currently filled by a single transistor. Its bypass capability adds features over the single transistor solution with no performance loss. The device can also be used as a driver amplifier for CDMA8. The purpose of the switch feature is to prevent distortion of high signal levels in receiver applications by bypassing the amplifier. Furthermore, zero current draw, when in bypass mode, saves current thus improving battery life. The internally matched switching circuit provides a 2 db gain step and also reduces gain ripple and mismatch in system usage. The MGA-7154 is a small LNA/ Bypass Switch MMIC that provides a low noise figure, a high gain and high third order input intercept point (IIP) ideal for the first stage LNA of PCS CDMA and W-CDMA. Device Description The MGA-7154 is a single stage GaAs IC with a built-in bypass switch housed in a SOT-4 package. The device diagram is shown in Figures 1 and 2. RF in Bypass Mode RF out Amplifier Mode Figure 2. Simplified Schematic. Input & DC ref GND + + Control Gain FET Output & V d GND & Vc Figure. Bypass State Duplicates the In and Out Impedance. The MGA-7154 features a minimum noise figure of.8 db and 16 db available gain. The input and output are partially matched, and only a simple series/shunt inductor match is required to achieve low noise figure and VSWR into 5Ω. When set into the bypass mode, both input and output are internally matched through a mitigative circuit. This circuit draws no current (less than 2 µa), yet duplicates the in and out impedance of the LNA (Figure ). This allows the system user to have minimum mismatch change from LNA to Bypass mode, thus allowing the same matching network at both states (LNA State and Bypass State). This makes the MGA-7154 ideal for use between duplexers and image reject filters. The MGA-7154 offers an integrated solution of LNA with adjustable IIP. The IIP can be fixed to a desired current level for the receiver s linearity requirements. The LNA has a bypass switch function, which sets the current to zero (2 µa) and provides low insertion loss when in bypass mode. The bypass mode also boosts dynamic range when high level signal is being received. Many CDMA systems operate 2% LNA and 8% bypass mode. For example, with the bypass draw of zero and LNA of 1 ma, the MGA-7154 allows an average of only 2 ma current. The MGA-7154 is a GaAs MMIC, processed on Avago s cost effective PHEMT (Pseudomorphic High Electron Mobility Transistor Technology). It is housed in the SOT4 (SC7 4-lead) package. Biasing This IC can be biased like a depletion mode discrete GaAsFET. Two kinds of passive biasing can be used: gate bias (Figure 4) and source resistor bias method (Figure 6). Gate Bias Pins 1 and 4 (Figure 4) are DC grounded and a negative bias voltage is applied to Pin in addition to the power supply (2.7 or V) applied to Pin 2. This method of biasing has the advantage of minimizing parasitic source inductance because the device is directly DC and RF grounded. 14

Input V ref 4 71 Figure 4. Gate Bias Method. 1 2 Output & Vd The DC supply at the input terminal (V ref ) can be applied through a RF choke (inductor). The voltage at V ref (Pin ) with respect to ground determines the device current, I d. A plot of typical I d vs. V ref is shown in Figure 5. Maximum device current (approximately 6 ma) occurs at V ref = (i.e. V gs = ). When using the gate biasing method, the bypass mode is activated when V ds = V and V ref < -2V. I d (ma) 7 6 5 4 2 1-1 -.8 -.6 -.4 -.2 V ref (V) Figure 5. Device Current vs. V ref. This kind of biasing would not usually be used unless a negative supply voltage was readily available. Source Resistor Bias This is the recommended method because it only requires one (positive) power supply. As shown in Figure 6, Pin is DC grounded and pins 1 and 4 are RF bypassed. The current of the amplifier (I d ) is set by the value of the resistor R bias. This resistor (R bias ) is connected at Pin 4 as shown in Figure 6 and RF bypassed. At least two capacitors in parallel are recommended for RF bypassing. One capacitor (1 pf) for high frequency bypassing and a second, large value capacitor for better low frequency bypassing. The large value capacitor is added in parallel to improve the IP because they help ground the low frequency mixing terms that are generated during a two tones test (i.e. f 1 f 2 term which is the separation of the two tones usually 1 to a few MHz) and thus improve the IIP. Input 4 Rbias 71 1 2 Output & Vd Figure 6. Source Resistor Bias Method. Maximum current (about 6 ma) occurs when R bias =. A plot of typical I d vs. R bias is shown in Figure 7. Id (ma) 6 5 4 2 1 2 4 6 8 1 12 14 R bias (Ω) Figure 7. Device Current vs. R bias. The approximate value of the external resistor, R bias, may also be calculated from: R bias = 964 (1.112 I d ) I d where R bias is in ohms and I d is the desired device current in ma. A simple method for DC grounding the input terminal (Pin ) is to use a shunt inductor that is also part of the noise-matching network. Adaptive Biasing For applications in which input power levels vary over a wide range, it may be useful to dynamically adapt the bias of the MGA-7154 to match the signal level. A sensor senses the signal level at some point in the system (usually in the baseband circuitry) and automatically adjusts the bias current of the amplifier accordingly. The main advantage of adaptive biasing is conservation of supply current (longer battery life) by using only the amount of current necessary to handle the input signal without distortion. Adaptive biasing of the MGA-7154 can be accomplished by simple digital means (Figure 8). For instance simple electronic switches can be used to control the value of the source resistor in discrete increment. DC Return Path 1 4 2 Digital Control 15 Figure 8. Adaptive Bias Control using Digital Method.

Applying the Device Voltage Common to all methods of biasing, voltage V d is applied to the MGA-7154 through the RF output connection (Pin 2). The bias line is capacitively bypassed to keep RF from the DC supply lines and prevent resonant dips or peaks in the response of the amplifier. Where practical, it may be cost effective to use a length of high impedance transmission line (usually λ/ 4 line) in place of the RFC. When using the gate bias method, the applied device voltage, V ds, is equal to voltage V d (at pin 2) since V s is zero. RF Input 1 71 Vref = -.5 V 2 4 Figure 9. DC Schematic for Gate Bias. V d ~ +2.5 V RF Output For source resistor biasing method, the applied device voltage, V ds, is V d V s. The bias control voltage is V s (Pin 4) which is set by the external bias resistor. A source resistor bias circuit is shown in Figure 1. RF Input 1 71 4 2 R bias V d = + V RF Output Figure 1. DC Schematic for Source Bias. Controlling the Switch The device current controls the state of the MGA-7154 (amplifier or bypass mode). For device currents greater than ma, it functions as an amplifier. If a lower current is drawn, the gain of the amplifier is significantly reduced and the performance will degrade. If the device current is set to zero, the MGA-7154 is switched into a bypass mode in which the signal is routed around the amplifier with a loss of about 5.6 db. The simplest way of switching the MGA-7154 to the bypass mode is to open-circuit the terminals at Pins 1 and 4. The bypass mode is also set by increasing the source resistance R bias to greater than 1MΩ. With the DC ground connection open, the internal control circuit of the MGA-7154 autoswitches from amplifier mode into a bypass mode and the device current drops to near zero. Typical bypass mode current is 2 µa. 2 1 4 R bias Bypass Switch Enable Figure 11. MGA-7154 Amplifier/Bypass State Switching. A digital switch can be used to control the amplifier and Bypass State as shown in Figure 11. Switching Speed The speed at which the MGA-7154 switches between states is extremely fast. The intrinsic switching speed is typically around 1 ns. However in practical circuits, the switching speed is limited by the time constants of the external bias circuit components (current setting resistor and bypass capacitors). These external components increase the switching time to around 1ns. Furthermore, the switching ON time is slightly lower (faster) than the switching OFF time (i.e. It switches on faster). Thermal issues The Mean Time To Failure (MTTF) of semiconductors is inversely proportional to the operating temperature. When biased at V and 1 ma for LNA applications, the power dissipation is V x 1 ma = mw. The temperature increment from the RFIC channel to its case is then mw x θ jc =. watt x 24 C/watt = 7.2 C. Subtracting the channel-to-case temperature rise from the suggested maximum junction temperature of 15 C, the resulting maximum allowable case temperature is 14 C. The worst case thermal situation occurs when the MGA-7154 is operated at its maximum operating conditions in an effort to maximize output power or achieve minimum distortion. A similar calculation for the maximum operating bias of 4.2 volts and 5 ma yields a maximum allowable case temperature of 1 C. (i.e. 21 mw x θ jc =.21 watt x 24 C/watt = 5.4 C 15 C 5.4 C = 1 C.) This calculation assumes the worst case of no RF power being extracted from the device. When operated in a saturated mode, both power-added efficiency and the maximum allowable case temperature will increase. Note: Case temperature for surface mount packages such as the SOT-4 refers to the interface between the package pins and the 16

mounting surface, i.e., the temperature at the PCB mounting pads. The primary heat path from the RFIC chip to the system heatsink is by means of conduction through the package leads and ground vias to the ground plane of the PCB. Grounding Consideration in PCB Layout The MGA-7154 requires careful attention during grounding. Any device with gain can be made to oscillate if feedback is added. Since poor grounding adds series feedback, it can cause the device to oscillate. Poor grounding is one of the most common causes of oscillation in RF components. Careful attention should be used when RF bypassing the ground terminals when the device is biased using the source resistor method. Package Footprint The PCB pad print for the miniature, 4-lead SOT-4 (SC7) package is shown in Figure 12. 1..9.6.24 1..51 1.15.45 Dimensions in 2..79.9.5 mm inches Figure 12. Recommended PCB Pad Layout for Avago s SC7 4L/SOT-4 Products. The layout is shown with a footprint of the MGA-7154 superimposed on the PCB pads for reference. RF bypass For layouts using the source resistor method of biasing, both of the ground terminals of the MGA-7154 must be well bypassed to maintain device stability. Beginning with the package pad print in Figure 12, and RF layout similar to the one shown in Figure 1 is a good starting point for using the MGA-7154 with capacitor-bypassed ground terminals. It is a best practice to use multiple vias to minimize overall ground path inductance. Size 42 recommended for the bypass capacitors 71 Figure 1. Layout for RF Bypass. PCB Materials.1 inches thick of FR-4 or G-1 type dielectric materials are typical choices for most low cost wireless applications using single layer printed boards. As an alternative, a Getek material with a multilayer printed circuit board can be used for a smaller size board, where: 1 st layer: RF routing layer 2 nd layer: Ground layer rd layer: Power (DC) routing layer 4 th layer: Other RF routing layer The spacing between the layers is as follows: Between the 1 st and 2 nd :.5" Between the 2 nd and rd :.2" Between the rd and 4 th :.5" LNA Application In the following sections the LNA design is described in a more general way. Sample evaluation boards for 19 MHz and 8 MHz are shown in a table (Table 1) and the appropriate board diagram is shown (Figures 22 and 2). A second smaller size board is also shown (Figures 25 and 26) with the corresponding table (Table 2). The smaller board is an example of reducing the size of the layout, more suitable for handset manufacturers. For low noise amplifier application, the LNA is typically biased 6 to 2 ma. The MGA-7154 is a conditionally stable device, therefore, the proper input and output loads must be presented in addition to properly RF grounding the device. Please refer to the stability section for tips on preventing oscillation. The LNA can be switched ON or OFF by a simply varying the resistor to its ground leads as described in previous sections. Matching Networks for the LNA 5Ω Input Match Γ in Γ s or Γ opt LNA Γ L Γ opt Output Match Figure 14. Input and Output Matching Terminology. 5Ω The input matching network determines the noise figure and return loss (S11) of our amplifier. The output-matching network determines the IP and output return loss (S22). Furthermore, both input and output matching networks influence the gain. The best gain (Maximum Available Gain-MAG) and lowest input return loss is obtained when both the input and output are conju- 17

gately matched to 5Ω. For instance at the input, when Γ s = Γ in * the highest gain with the best power transfer is obtained where Γ s is the source reflection coefficient presented to the input pin. For best noise, Γ s = Γ OPT, where Γ OPT is the source reflection coefficient for optimum NF match and is determined empirically (experimentally). However, an input match where Γ s = Γ OPT does not necessarily yield the best return loss nor the best gain. Input Match To allow flexibility for the designer, the LNA is intended to be used with external matching network at the input. The noise performance of a two port can be determined if the values of the noise parameters F min, r n = R n /5 and Γ OPT are known (shown in the datasheet), where these parameters are given by: F 5 = F min + 4r n Γ s Γ OPT 2 (1 Γ s 2 ) 1 + Γ OPT 2 r n = (F 5 F 1 + Γ min) OPT 2 4 Γ OPT 2 Γ OPT = Z OPT Z O Z OPT + Z O Where F min is the minimum noise figure that is obtained when Γ s = Γ OPT. R n is the noise resistance that indicates the sensitivity of the noise performance. Γ s is the source reflection coefficient presented to the input pin. Γ OPT is the source reflection coefficient for optimum NF match. Any change in Γ s affects the noise figure of our amplifier. To obtain the best noise figure, the following relation: Γ s = Γ OPT must be satisfied. However, this might affect our return loss at the input because it creates more mismatch (at the input) and there is less power transfer to the LNA. Therefore the best solution should be the one that gives a reasonable input return loss with the best noise figure associated to it. The noise figure F of an amplifier is determined by the input matching circuit. The output matching does not affect the noise (has a significantly minimal effect on noise figure). To obtain the best noise match a simple two elements match is used at the input of the device. Using the Γ OPT magnitude and phase at the frequency of interest, the noise match is done. The topology that has a capacitor to ground is ignored because it does not allow the input to be DC grounded as is required by the source bias method. Therefore the series-l-shunt-l topology is used. The final values of the noise matching circuit (input match) was a result of some more empirical tuning in the lab that was a compromise between the various important parameters. Typical Gain, noise and stability circles are shown in Figures 17 2. Most simulations were done using Avago-EEsof s Advanced Design System (ADS). Stability A stable circuit is a circuit that does not oscillate. Oscillation can take the form of spurious signal and noise generation. This usually results in changes in DC operating point (bias level fluctuates). The oscillations can be triggered by changes in the source (input match), load (output match), bias level and last but not least: improper grounding. Design for Stability The main potential for oscillation with the MGA-7154 is improper grounding and/or improper RF bypass capacitors. Any device with gain can be made to oscillate if feedback is added. Proper grounding may be achieved by minimizing inductance paths to the ground plane. Passive components should be chosen for high frequency operation. Bias circuit self resonance due to inadequate bypass capacitors or inadequate grounding may cause high frequency, out of band, instability. Smaller 42 size bypass capacitors are recommended to minimize parasitic inductance and resonance of the bias circuit. Statistical Parameters Several categories of parameters appear within the electrical specification portion of the MGA-7154 datasheet. Parameters may be described with values that are either minimum or maximum, typical or standard deviations. The values for parameters are based on comprehensive product characterization data, in which automated measurements are made on a statistically significant number of parts taken from nonconsecutive process lots of semiconductor wafers. The data derived from product characterization tends to be normally distributed, e.g. fits the standard bell curve. 68% 95% -σ -2σ 99% -1σ Mean (µ) +1σ +2σ +σ (typical) Parameter Value Figure 15. Normal Distribution Curve. 18

Parameters considered to be the most important to system performance are bounded by minimum or maximum values. For the MGA-7154, these parameters are: V ref test, NF test, G atest, IIP test, and IL test. Each of the guaranteed parameters is 1% tested as part of the normal manufacturing and test process. Values for most of the parameters in the table of Electrical Specifications that are described by typical data are the mathematical mean (µ), of the normal distribution taken from the characterization data. For parameters where measurements or mathematical averaging may not be practical, such as S-parameters or Noise parameters and the performance curves, the data represents a nominal part taken from the center of the characterization distribution. Typical values are intended to be used as a basis for electrical design. To assist designers in optimizing not only the immediate amplifier circuit using the MGA-7154, but to also evaluate and optimize tradeoffs that affect a complete wireless system, the standard deviation (σ) is provided for many of the Electrical Specification parameters (at 25 C). The standard deviation is a measure of the variability about the mean. It will be recalled that a normal distribution is completely described by the mean and standard deviation. Standard statistics tables or calculations provide the probability of a parameter falling between any two values, usually symmetrically located about the mean. Referring to Figure 15 for example, the probability of a parameter being between ±1σ is 68.%; between ±2σ is 95.4%; and between ±σ is 99.7%. Phase Reference Planes The positions of the reference plane used to specify S-parameters and Noise Parameters for the MGA-7154 are shown in Figure 16. As seen in the illustration, the reference planes are located at the point where the package leads contact the test circuit. Reference Planes Test Circuit Figure 16. Phase Reference Planes. 19

Demonstration Board Load unstable region G = 17.8 db G = 16.8 db Load stable region G = 15.8 db G = 14.8 db Source unstable G = 18.8 db NF =.95 db NF = 1.15 db NF = 1.5 db NF = 1.55 db Source stability circle Source stable Load stability circle NF =.75 db Gain Circles Noise Circles Figure 18. Gain, Noise and Stability Circles. Figure 19. Noise Circles F = 19 MHz, Step Size:.2 db. Figure 2. Gain Circle F = 19 MHz, Step Size: 1. db. Figure 21. Load and Source Stability Circles. V d +.V C11 C1 C4 C5 R4 L C9 RF Output RF Input C1 L1 1 71 C6 2 4 C7 C8 L2 C2 SW1 R R1 SW2 R2 Figure 22. Schematic Diagram of Evaluation Board Amplifier. 2

Agilent MGA-7154 Eval Circuit GND Vd C11 C4 C5 R4 C1 L OUT IN C1 L1 C6 C9 L2 C2 C7 R C8 R2 R1 Vc EB 7/ REV 2 Figure 2. Amplifier Evaluation Circuit with Component Designators. Actual board size is 1.1 x 1. inches,.1 inches thick. Board Designation Description Part Number Package PCS-19 8 MHz 71 DUT [1] DUT [1] MGA-7154 SOT-4 (4 lead SC-7 package) C1 1 pf 8.2 pf Size 42 C2, C5, C6, C7, C1 1 pf 1 pf Size 42 C9 47 pf 2.7 pf Size 42 C4, C8, C11.1 µf.1 µf Size 6 or 42 L1 1.5 nh 18 nh TOKO LL15 Size 42 L2 2.7 nh nh TOKO LL15 Size 42 L.9 nh nh TOKO LL15 Size 42 R1 51Ω 51Ω Size 42 R2 115Ω 115Ω Size 85 (for 6mA Bias) R4 / L4 Ω (19) 18 nh /LL168-FH or 15-FH Size 85 (Jumper)/ Size 6 (inductor) R 6Ω 6Ω Size 85 (for 1mA Bias) Note 1: Device under Test Table 1. Component Values for 19 MHz and 8 MHz. 21

MGA-7154 Demodulator Analog Front-end Digital Base-band Processor ADC ADC Dual Synthesizer Dual VCO DAC DAC RF Control Signal (PDM ) Figure 24. System Level Overview of MGA-7154 for Handset Designers. These are the actual necessary components. The other connectors and board space are only for production. RF1 PCS_IN C8 C9 L6 blue2_lna rev2.1 C6 Cell_LNA L25 U2 R7 L7 C44 R8 C7 R25 C8 R21 R2 U4 L5 PCS_LNA PCS_OUT C12 R24 C47 PCS_LNA RF.1 mm 1. in PCS_IN C9 L6 C6 C8 L7 R8 C8 U2 L25 R7 C44 C7 R21 L5 R25 C12 C47 R24 J1 J9 J8 J7 GND Vcc R2 Vcc GND AGILENT TECHNOLOGIES 2.1 mm.791 in GND U4 R28 R18 Cell_LNA R17 PCS_LNA R16 PCS_LNA Software controlling the switch Manual switch control Figure 25. Small Size Amplifier Board with Components for Handset Focussed Designers. 22