Combi sensor A B D C B B A: Wind wheel B... B: Brightness sensors west, east, south C: Dawn sensor D: Rain sensor Combi sensor WS 0 KS with DCF77 receiver WS 0 KSDCF The combi sensor serves for the measurement of the wind speed, brightness dawn and rain. The brightness can be measured for three directions, south, east and west, separately. The combi sensor will be connected directly to the weather station ( REG W) which evaluates the measured and transmits these as switching or value telegrams to the bus. The combi sensor WS 0 KSDCF includes an additional DCF77 receiver for the official German time signal. The combi sensor needs an external V AC supply, e.g. power supply WSSV 0. Supply: V AC ± 5 %, 50/60 Hz Max. current consumption: 600 ma Power consumption: max.. W (sensors and heating) Ambient temperature: 5 C... +5 C Connection cable: LiYCY, 6 x 0.5 mm, 0 m, max. 50 m Ambient temperature: 0 C... +60 C, ice free Storage/transport temperature: 0 C... +60 C Protection: IP 55, in standard purpose acc. to DIN EN 6059 Safety class: III Dimensions: 0 x 00 mm (without mounting bracket) Fastening: mounting bracket for wall or mast Sensor signals Wind speed: Accuracy: Rain: Sensitivity: Switch On delay: Switch Off delay: Brightness Spectral range: Resolution: Direction: Dawn Resolution:... 0 m/s 0.5 m/s, 0 C... +60 C Yes / No fine drizzle approx. rain particles approx. minutes 0... 0 KLux 700... 050 nm 0 bit east, south, west 0... 67 Lux 0 bit 6
Analog Sensors for Weather Station Wind sensor brown operating volt. + V white correspond. ground green output 0 V / 0 V yellow correspond. ground pink heating V grey heating V WS 0 W The wind sensor converts the wind speed into electrical signals. These signals are generated by a Reed contact which closes under the influence of magnets. The generated impulses are transformed into an output voltage proportional to the wind speed. A PTC-heating element takes care for a trouble free winter operation (only in combination with heating transformer WSSV 0). 0,7... 0 m/s 0... 0 V at 0 m/s Supply voltage: 8... V DC Current consumption: 6... ma Contact type: Reed contact Heating: PTC-element (800 C) Operating voltage heating: V AC/DC Lead wire: m (LIYY 6 x 0.5 mm ) 7
Analog Sensors for Weather Station Rain sensor brown operating volt. + V white correspond. ground green output 0 V / 0 V yellow heating V grey heating V WS 0 R The rain sensor is used for the measuring and evaluation of the rainfall. With a meander shaped sensor the conductance of the rain water is evaluated. A micro processor controls the heating (only in combination with heating transformer WSSV 0) and offers an output signal of 0 V or 0 V. Range of the electrical output: 0 V dry / 0 V rain (min. kω load) Lead wire: m (LIYY 5 x 0.5 mm ) with sealed electronics 8
Weather station WS 0.. Brightness sensor operating volt. + V correspond. ground output 0... 0 V WS 0 H The brightness sensor is used for the measuring and evaluation of the brightness. The brightness measured by a photodiode is transmitted to an analog output signal of 0 V 0 V by the electronics. 0... 60.000 Lux, linear 0 V... 0 V, short-circuit / proof with PG7 thread + screw and pressure respectively moisture compensation (recommended cable x 0.5 mm ) Dawn sensor operating volt. + V correspond. ground output 0... 0 V WS 0 D The dawn sensor is used for the measuring and evaluation of the brightness (dawn/dusk). The brightness measured by a photodiode is transmitted to an analog output signal of 0 V 0 V by the electronics. 0... 55 Lux, linear 0 V... 0 V, short-circuit / proof with PG7 thread + screw and pressure respectively moisture compensation (recommended cable x 0,5 mm ) 9
Weather station WS 0.. Temperature sensor operating volt. + V correspond. ground output 0... 0 V WS 0 T The temperature sensor is used for the measuring and evaluation of the temperature. The temperature measured by a temperature sensor is transmitted to an analog output signal of 0 V 0 V by the electronics. 0 C... +70 C, linear 0 V... 0 V, short-circuit / proof with PG7 thread + screw and pressure respectively moisture compensation (recommended cable x 0.5 mm ) 0