Wesite: www.sorellefurniture.om Berkley ri and hanger Assemly Instrution Important Information: Read all instrutions BEFORE assemling ri. KEEP INSTRUTIONS FOR FUTURE USE. Made in QHY, China
Cri Warnings: WARNING: SORELLE *Infants an suffoate on soft edding. Never add a pillow or omforter. Never plae additional padding under an infant. *Failure to follow these warnings and the assemly instrutions ould result in serious inury or death. DO NOT use this ri if you annot exatly follow the aompanying instrutions. *To redue the risk of SIDS, pediatriians reommend healthy infants e plaed on their aks to sleep, unless otherwise advised y your physiian. *Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not plae items with a string around a hild's nek, suh as hood strings or paifier ords. Do not suspend strings over a ri or attah strings to toys. *Strangulation Hazard: To help prevent strangulation tighten all fasteners. A hild an trap parts of the ody or lothing on loose fasteners. *Strangulation Hazard: Do not plae ri near window or patio door where ords from linds or drapes may strangle a hild. *Fall Hazard: When hild is ale to pull to a standing position, set mattress to lowest position and remove umper pads, large toys and other oets that ould serve as steps for liming out. This ri has an adustale mattress support. For the onveniene of the parent when the ay is very small, the mattress support may e used in the highest position. *Fall Hazard: Stop using ri when hild egins to lim out or reahes a height of 35in. (89m), whihever ours first. The hild should e plaed in a youth or regular ed. *Chek this produt for damaged hardware, loose oints, loose olts or other fasteners, missing parts, or sharp edges efore and after assemly and frequently during use. Seurely tighten loose olts and other fasteners.do not use ri if any parts are missing,damaged or roken.contat C&T International / Sorelle for replaement parts and instrutional literature if needed. Do not sustitute parts. *Follow warnings on all produts in a ri. *If refinishing, use a non-toxi finish speified for hildren's produts. *Never use plasti shipping ags or other plasti film as mattress overs eause they an ause suffoation. *Infants an suffoate in gaps etween ri sides and a mattress that is too small. *Ensure a safe environment for the hild y heking regularly, efore plaing the hild in the ri, that every omponent is properly and seurely in plae. *To avoid head inury, do not allow any hild to play underneath the ri. *Never add an aessory suh as a assinet or hanging tale that extends over the sleeping area. CAUTION : ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 271/4 (69CM) x 515/8 (131 CM) WITH A THICKNESS NOT EXCEEDING 6 (15CM). Page 2
Toddler Bed Warnings: WARNING INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT. Openings in and etween ed parts an entrap head and nek of a small hild. NEVER use ed with hildren younger than 15 months. ALWAYS follow assemly instrutions. The maximum user weight is 50ls (22.7kg) WARNING STRANGULATION HAZARD NEVER plae ed near windows where ords from linds or drapes may strangle a hild. NEVER suspend strings over a ed. NEVER plae items with a string, ord, or rion, suh as hood strings or paifier ords, around a hild's nek. These items may ath on ed parts. CAUTION ENTRAPMENT HAZARD To avoid dangerous gaps, any mattress used in this ed shall e a full-size ri mattress at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in thikness. The mattress thikness must not exeed 6 in (150mm). Changing Tale Warnings: WARNING FALL HAZARD - to prevent death or serious inury, always keep hild within arm s reah. Read all instrutions efore use of the hanging tale. KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE. Inspet the hanging tale periodially. Do not use the hanging tale if it is damaged or roken. Contat C&T International In. with any questions. Tighten all loose srews and olts efore eah use. The maximum reommended weight of the hild is 30ls for the hanging tale. Use only the pad provided y C&T International / Sorelle or Manufaturer s Always seure the pad to the hanging surfae y inserting the strap through the hole in the middle of the pad. See Instrutions. NEVER use ri without Changing Tale attahed Page 3
NOTES ON ASSEMBLY: -During the assemly proess whenever using srews or olts, hek eah y plaing the srew/olt on the diagram of the item whih is drawn atual size and design. Be sure to use the proper size and shape speified in the instrutions. -To assemle this unit you may e required to plae the unit on it s side and fae. It is strongly reommended that assemly is done on a soft, non-arasive surfae to avoid damaging the finish. NOTES ON USE: Keep hildren and others safe y following these simple rules: - Do not allow any hild to play on furniture - Do not allow liming on any piee of furniture. - Do not allow hanging from any piee of furniture. - Always monitor your hild s ativity when in the nursery. NOTES ON CARE AND MAINTENANCE: - Do not srath or hip the finish. - Inspet the produt periodially, ontat C&T International / Sorelle for replaement parts or questions. - Do not store the produt or any parts in extreme temperatures and onditions suh as a hot atti or a damp, old asement. These extremes an ause a loss of strutural integrity. -To preserve the luster of the high quality finish on your produt, it is reommended to plae a doily or AU BE A A THI felt pad under any items you plae on the finish. -Clean with a damp loth, then a dry loth to preserve the original luster and eauty of this fine finish. -Do not use arasive hemials. -Do not spray leaners diretly onto furniture. -Lift slightly when moving on arpeting to prevent leg reakage. -Use of a vaporizer near furniture will ause wood to swell and finish to peel. Cleaning and Storage SORELLE To lean, use only mild household soap and warm water. DO NOT use leah or detergent. DO NOT use arasive leaners whih an srath the finish. Use lean soft loths to wash, rinse and dry. With proper are, the quality finish will last a long time. Wood surfaes may e treated with a light appliation of a good grade of non-toxi furniture polish. Read ontents on ak of polish to make sure polish will not harm unit. Store all parts from Cri, whih are not used for Full Size Headoard, in original arton(s) (if availale) to prevent damage and allow reuse. Page 4
Assemly Parts SORELLE (A) Left End (x1) (A1) Middle Panel (x1) (A2) Right End (x1) (C) Footoard (x1) (B) Headoard (x1) (D) Left -Front Post (x1) (D1) Middle - Front Post (x1) (D2) Left - Bak Post (x1) (E) Middle - Rear Post (x1) (F) Rear - Top (x1) (G) Middle Bar (x3) (H) Middle-Up Bar (x1) (J) Front - Up Bar (x1) (K) Front- Middle Bar (x1) (L) Front- Bottom Bar (x1) ( M ) Middle-Bottom Support Bar (x1) ( N ) Changer Top Shelf with Support Bar (x1) (O) Bak Shelf (x1) ( P ) Bak-Bottom Shelf (x1) ( Q ) Changer Middle MDF Panel (x1) ( R ) Drawer Front (x2) (R1) Drawer Left (x2) (R2) Drawer Right (x2) (R3) Drawer Bak (x2) (R4) Drawer Bottom (x2) ( S ) Changing Pad (x1) ( T ) Middle Shelf Panel (x1) Page 5
Assemly Parts Hardware list (a) M6 x 85mm Allen olt (4 ps) (e) M6 x 35mm Allen olt (3 ps) () M6 x 60mm Allen olt (16 ps) (f) M6 x 17mm Allen olt (4 ps) () M6 x 50mm Allen olt (12 ps) ( g ) M4 x 26mm Allen olt (2 ps) (d) M6 x 45mm Allen olt (6 ps) (i) 8 x 30 mm Wood Dowels (3 ps) (k) Metal Shelf Support (4 ps) 25mm Wood Srew (16 ps) () 6 x 30 mm Wood Dowels (14 ps) (l) Srewdriver (1 p) ( m ) Kno (x2) (n) Allen Key (1 p) (p) Barrel Nut (4 ps) (o) Mattress Base (1 p) Page 6
Cri Assemly 1 Attah Left End (A) to left front and ak posts (D&D2) y using 6 Bolts ( ) as Figure 1. Attah Middle End (A1) to Middle front and ak postd (D1&E) y using 6 Bolts ( ) &1 olts( e ) and 1 wood dowels( i ) as Figure 1. e i A1 (i) 8 x 30 mm Wood Dowels X1 E D2 Fig.1 A D D1 (e) M6 x 35mm Allen olt X1 () M6 x 50mm Allen olt X12 2 Attah headoard (B) to Left-ak Post (D2) and Middle-ak Post (E) y using 4 Bolts( a )& 4 arrel nut( p ) and 2 wood dowels( i )as Figure 2. i a B p i p a p a E (i) 8 x 30 mm Wood Dowels X2 p (p) Barrel Nut X 4 n D2 Fig.2 (a) M6 x 85mm Allen olt X 4 Page 7
3 Attah the Front-Up Bar ( J ),Front- Bottom Bar (L), Front Middle Bar(K), and Middle Bar (G) to the Front Middle Post (D1) using 4 Bolts( ) and 3 Wood Dowels( ). Attah Middle - Bottom Bar(M) to the Middle Panel (A1) using 1 Bolt ( e ) and 1 wood dowel ( ) as seen elow in Figure 3. J e A1 M G K L () 6 x 30 mm Wood Dowels X 4 n D1 (e) M6 x 35mm Allen olt X 1 Fig.3 () M6 x 60mm Allen olt X 4 4 Attah the Rear Top (F) and 2 Middle Bar ( G) to Middle - Rear Post ( E ) using 4 Bolts( ) and 2 Wood Dowels( ). Attah Middle - up Bar (H) to the Middle Panel using 1 Wood Dowel( ) as seen elow in Figure 4. A1 F H G B () 6 x 30 mm Wood Dowels X 3 Fig.4 G E () M6 x 60mm Allen olt X 4 Page 8
5 Insert Changer Top Shelf with Support Bar (N) & Changer Middle MDF Panel (Q) & Bak - Bottom Shelf (P) & Middle shelf panel ( T ) to Grooves as seen elow in Figure 5. N T Q Fig.5 P 6 Attah the Right End ( A2) to the end of the ri using 8 Bolts ( ), 1 Bolt ( e ), and 7 Wood Dowels ( ) as seen elow in Figure 6. F () 6 x 30 mm Wood Dowels X 7 J N (e) M6 x 35mm Allen olt X 1 A2 Fig.6 () M6 x 60mm Allen olt X 8 L e Page 9
7 Attah Mattress Base ( o ) to ri y using 4 Bolts( f ) as Figure 7. NOTE: For infants, set mattress support assemly in an upper position for greater aessiility. As hild grows and an stand, mattress support assemly must e lowered. See Warning Statements. (f ) M6 x 17mm Allen olt (4 ps) (4x) o f o Fig.7 8 Attah FootBoard (C) to Left-Front Post(D) & Middle-Front Post (D1) y using 6 Bolts( d ) as Figure 8. d d d d d n D1 d C Fig.8 D (d) M6 x 45mm Allen olt (6 ps) Page 10
Drawer Assemly 1. Working on a padded flat surfae, attah Drawer Sides (R1&R2) to Drawer Bak (R3) with Philips Head Srew. Figure 1 1 (R1) (R3) Grooves (R2) 2. Slide Drawer Bottom (R4) into drawer assemly. Figure 2. 2 (R4) 3. Seure oth sides of Drawer Front (R) to drawer assemly with four (4) Srews. Figure 3. 3 (R) Chek all srews for tightness. 4. Using Drawer Kno Srew ( g ), install one (1) Kno ( m ) on Drawer. Figure 4. 4 ( g ) Repeat for all drawers. Set drawers aside for later use. ( m ) ( m ) Kno x 2 25mm Wood Srew x 16 ( g ) M4 x 26mm Allen olt x 2 (l) Srewdriver x 1 Page 11
9 Insert 4 Metal Shelf Support ( k ) into holes. Then put Bak Shelf (O) on 4 Metal Shelf Support ( k ) as Figure 10 O (4x) Fig.10 k 10 Insert two (2) drawers into hanger. Fig.11 Page 12
11 Add hanging pad to top of organizer. Fig.12 Changing Pad Assemly Important : If hanging pad and safety elt are assemled, make sure warnings are faing up and visile. If not, reassemle y following the steps elow. Important : Tighten all olts efore use your Cri. 1. Loate safety elt olted to dresser top. Insert safety elt through slit in hanging pad from ak of pad. Figure 1. 2. Pull through front of pad ompletely. Make sure pad is faing up and warnings are always visile. Figure 2. 3. Make sure that safety elt is fastened around hild, and adusted so safety elt is snug around hild s mid-setion. Make sure ukle is seurely lathed. Figure 3. 1 2 3 CLICK! Page 13
Disassemling Cri For Storage To disassemle ri for storage, follow assemly steps in reverse. Store all parts and hardware together in a safe plae. Store the instrution manual in the supplied envelope attahed to the mattress support assemly for future referene for re-assemly. Converting to a Toddler Bed (Optional) Follow all instrutions supplied with the 148# Toddler Rail System. NOTE:148# Toddler Rail System is not inluded. Please see your ri retailer, visit WWW.Sorellefurniture.om or ontat C&T International / Sorelle for more information. Additional Parts and Hardwares ( 148# Toddler Rail System Not inluded, sold separately) a M6*50mm Bolt (4ps) (A) 148 Toddler Rail (1 ps) TODDLER BED ASSEMBLY IMPORTANT: MATTRESS SUPPORT MUST BE IN THE LOWEST POSITION Page 14
Fullsize Bed and Changer Tale Conversion (Optional) Follow all instrutions supplied with the 224# Adult Rail System. NOTE: 224# Adult Rail System is not inluded. Please see your ri retailer, visit WWW.Sorellefurniture.om or ontat C&T International / Sorelle for more information.. Page 15