TOULOUSE Dresser
Important Retain for future reference: Read carefully Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product. Your child s safety is your responsibility. If you have a query with this product or require replacement parts, please contact 01692 408802. Lay out the parts on a soft level surface and compare to the part/fixing checklist on pages 2 and 3. Do not discard any packaging until you are sure that you have all the parts. Keep children clear during assembly as pack contains small parts which may present a choking hazard. You will need the following tools to complete assembly: Flat-headed screwdriver and cross-point screwdriver. Hardware A x 16 B x 13 C x 48 D x 5 E x 5 F x 14 G x 27 (25mm) H x 28 (15mm) I x 12 J x 6 Hexagon Key x 1 2
Wooden Parts Changer Divider 2 Changer Side 1 Changer Divider 1 Changer Rear Changer Front Changer Side 2 Dresser Top Twin Drawer Front Side Panel x 2 (L & R) Single Drawer Front x 2 Upper Back Panel Upper Front Crossbar Front Crossbar Lower Back Panel Plain Crossbar x 4 Upper Rear Crossbar Drawer Side x 6 (L X R) Drawer Back x 3 Drawer Base x 3 Drawer Brace x 3 3
Assembly 1 Upper Front Crossbar Plain Crossbar x 4 Front Crossbar Upper Rear Crossbar C x 14 Take care to insert the dowels into the correct holes as indicated. Repeat for the opposite end of each crossbar. (Total 28 x part C) Assembly 2 Side Panel Upper Front Crossbar Plain Crossbar Upper Rear Crossbar Plain Crossbar Front Crossbar Plain Crossbar A F Secure all Crossbars using Parts A and F (1 each per Crossbar) as shown. Plain Crossbar 4
Assembly 3 Side Panel F A Secure Crossbars using Parts A and F (1 each per Crossbar) as shown. Assembly 4 Changer Front Changer Divider 1 Changer Side 2 D x 5 5
Assembly 5 Changer Divider 1 Changer Side 2 Changer Side 1 C x 8 Changer Divider 2 C x 8 Assembly 6 Changer Side 1 Changer Side 2 Dresser Top B x 2 Assembly 7 Changer Divider 2 Changer Divider 1 E x 2 6
Assembly 8 Changer Front E x 3 Assembly 9 Changer Rear B x 5 7
Assembly 10 C x 4 Assembly 11 Changer Front Ensure the Dresser Top is assembled as shown. Dresser Top B x 3 B x 3 A x 2 Front Crossbar 8
Assembly 12 Upper Back Panel (Slot at top) Lower Back Panel H x 14 H x 14 Assembly 13 Twin Drawer Front Drawer Side Drawer Side G x 2 Repeat for remaining drawers. G x 2 Assembly 14 Drawer Base Repeat for remaining drawers. 9
Assembly 15 Drawer Back Drawer Brace Repeat for remaining drawers. Assembly 16 J x 2 G x 3 G x 2 I x 4 Repeat for remaining drawers. Assembly 17 Twin Drawer Front Single Drawer Front Single Drawer Front 10
Assembly 18 The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping. WARNING : Installation only to be carried out by a competent person. Check the suitability of the wall before fitting. Washer x 2 Screw (15mm) Screw (25mm) Plastic wall plug (for brick and masonry wall use only) Fabric strap 1. Place the dresser against the wall where it is to be fitted. Remove the top drawer and mark the wall through the slot in the Upper Back Panel. 2. Move the dresser away and using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the marked position. 3. Replace the dresser and thread the fabric strap through the slot in the Upper Back Panel. 4. Attach the fabric strap to the Upper Rear Crossbar using the 15mm screw and the washer. 5. Replace the top drawer. Before use, ensure that the strap is securely fixed to both the wall and the dresser. 1 2 4 The type of wall fixing you will require depends on the construction of the wall. See below for details. If in doubt, seek professional advice. Wood: If fixing to wood make sure that it isn t chipboard as screws can easily pull away the core structure. Brick or masonry: Use the wall plug, provided you are sure that your wall is sound. Cavity wall: Special toggle wall plugs needed. Seek expert advice. 11
Care & Maintenance Your furniture may be cleaned by wiping with a damp cloth and drying with a soft clean cloth. Do not use abrasives, bleach, alcohol or ammonia-based household polishes. Take care when handling or moving the furniture. Careless handling may cause damage. Regularly check that all fixings are tightened and that there are no broken or damaged parts. In use Warning: Do not leave your child unattended. All assembly fixings should always be tightened properly. Care should be taken that no screws are loose because a child could trap parts of their body, or clothing (e.g. strings, necklaces, ribbons, dummies, etc.) which could pose a risk of strangulation. Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the dresser. Suitable for use with a flat changing mat 76 x 47 cm which does not compromise the effective height of the changer barriers. The changing area is suitable for use up to 12 months old or 11kg in weight. When changing your child ensure anything stored in the separate compartments on top of the dresser is kept out of reach of your child. Do not use the dresser if any of the parts are broken, torn or missing. Any additional or replacement parts can only be obtained from the manufacturer or the distributor. Customer Care line for this Product 01692 408802 East Coast Nursery Ltd. Robertson House, North Walsham, Norfolk, NR28 0BX www.eastcoastnursery.co.uk 7839-02