8.3Vdc 14Vdc input; 0.75Vdc to 5.5Vdc output; 3A Output Current RoHS Compliant Applications Distributed power architectures Intermediate bus voltage applications Telecommunications equipment Servers and storage applications Networking equipment Enterprise Networks Latest generation IC s (DSP, FPGA, ASIC) and Microprocessor powered applications Description Features Compliant to RoHS EU Directive 2011/65/EU (-Z versions) Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this product will no longer be RoHS compliant (non-z versions) Delivers up to 3A output current High efficiency 91% at 3.3V full load (VIN = 12.0V) Small size and low profile: 20.3 mm x 11.4 mm x 7.27 mm (0.80 in x 0.45 in x 0.286 in) Low output ripple and noise Constant switching frequency (300 khz) Output voltage programmable from 0.75 Vdc to 5.5 Vdc via external resistor Line Regulation: 0.3% (typical) Load Regulation: 0.4% (typical) Temperature Regulation: 0.4 % (typical) Remote On/Off Output overcurrent protection (non-latching) Wide operating temperature range (-40 C to 85 C) UL* 60950-1Recognized, CSA C22.2 No. 60950-1- 03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Austin MiniLynx TM 12V SMT (surface mount technology) power modules are non-isolated dc-dc converters that can deliver up to 3A of output current with full load efficiency of 91% at 3.3V output. These modules provide precisely regulated output voltage programmable via external resistor from 0.75Vdc to 5.5Vdc over a wide range of input voltage (VIN = 8.3-14V). Their open-frame construction and small footprint enable designers to develop cost- and space-efficient solutions. In addition to sequencing, standard features include remote On/Off, programmable output voltage and over current protection. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.v. ** ISO is a registered trademark of the International Organization of Standards September 25, 2015 2015 General Electric Company. All rights reserved.
Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage All VIN -0.3 15 Vdc Continuous Operating Ambient Temperature All TA -40 85 C (see Thermal Considerations section) Storage Temperature All Tstg -55 125 C Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage Vo,set 3.63 VIN 8.3 12 14 Vdc Vo,set > 3.63 VIN 8.3 12 13.2 Vdc Maximum Input Current All IIN,max 2.2 Adc (VIN= VIN, min to VIN, max, IO=IO, max VO,set = 3.3Vdc) Input No Load Current VO,set = 0.75Vdc IIN,No load 45 ma (VIN = VIN, nom Vdc, IO = 0, module enabled) VO,set = 5.5Vdc IIN,No load 150 ma Input Stand-by Current All IIN,stand-by 1.2 ma (VIN = 5.5Vdc, module disabled) Inrush Transient All I 2 t 0.4 A 2 s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All 30 map-p Input Ripple Rejection (120Hz) All 30 db CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer s data sheet for further information. September 25, 2015 2015 General Electric Company. All rights reserved. Page 2
Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit Output Voltage Set-point All VO, set -2.5 VO, set +2.5 % VO, set (VIN=IN, min, IO=IO, max, TA=25 C) Output Voltage All VO, set -3% +4% % VO, set (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range All VO 0.7525 5.5 Vdc Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All 0.3 % VO, set Load (IO=IO, min to IO, max) All 0.4 % VO, set Temperature (Tref=TA, min to TA, max) All 0.4 % VO, set Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Cout = 1μF ceramic//10μftantalum capacitors) RMS (5Hz to 20MHz bandwidth) All 10 15 mvrms Peak-to-Peak (5Hz to 20MHz bandwidth) All 30 50 mvpk-pk External Capacitance ESR 1 mω All CO, max 1000 μf ESR 10 mω All CO, max 3000 μf Output Current All Io 0 3 Adc Output Current Limit Inception (Hiccup Mode ) All IO, lim 200 % Io (VO= 90% of VO, set) Output Short-Circuit Current All IO, s/c 2 Adc (VO 250mV) ( Hiccup Mode ) Efficiency VO,set = 1.2Vdc η 81.5 % VIN= VIN, nom, TA=25 C VO, set = 1.5Vdc η 84.0 % IO=IO, max, VO= VO,set VO,set = 1.8Vdc η 86.0 % VO,set = 2.5Vdc η 89.0 % VO,set = 3.3Vdc η 91.0 % VO,set = 5.0Vdc η 93.0 % Switching Frequency All fsw 300 khz Dynamic Load Response (dio/dt=2.5a/µs; VIN = VIN, nom; TA=25 C) All Vpk 200 mv Load Change from Io= 50% to 100% of Io,max; 1μF ceramic// 10 μf tantalum Peak Deviation Settling Time (Vo<10% peak deviation) All ts 25 µs (dio/dt=2.5a/µs; VIN = VIN, nom; TA=25 C) All Vpk 200 mv Load Change from Io= 100% to 50%of Io,max: 1μF ceramic// 10 μf tantalum Peak Deviation Settling Time (Vo<10% peak deviation) All ts 25 µs September 25, 2015 2015 General Electric Company. All rights reserved. Page 3
Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit Dynamic Load Response (dio/dt=2.5a/µs; V VIN = VIN, nom; TA=25 C) All Vpk 75 mv Load Change from Io= 50% to 100% of Io,max; Co = 2x150 μf polymer capacitors Peak Deviation Settling Time (Vo<10% peak deviation) All ts 100 µs (dio/dt=2.5a/µs; VIN = VIN, nom; TA=25 C) All Vpk 75 mv Load Change from Io= 100% to 50%of Io,max: Co = 2x150 μf polymer capacitors Peak Deviation Settling Time (Vo<10% peak deviation) All ts 100 µs General Specifications Parameter Min Typ Max Unit Calculated MTBF (VIN= VIN, nom, IO= 0.8IO, max, TA=40 C) Telecordia SR 332 Issue 1: Method 1, case 3 10,865,800 Hours Weight 2.8 (0.1) g (oz.) September 25, 2015 2015 General Electric Company. All rights reserved. Page 4
Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit On/Off Signal interface Device code with Suffix 4 Positive logic (On/Off is open collector/drain logic input; Signal referenced to GND - See feature description section) Input High Voltage (Module ON) All VIH VIN, max V Input High Current All IIH 10 μa Input Low Voltage (Module OFF) All VIL -0.2 0.3 V Input Low Current All IIL 0.2 1 ma Device Code with no suffix Negative Logic (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) Input High Voltage (Module OFF) All VIH 2.5 VIN,max Vdc Input High Current All IIH 0.2 1 ma Input Low Voltage (Module ON) All VIL -0.2 0.3 Vdc Input low Current All IIL 10 μa Turn-On Delay and Rise Times (IO=IO, max, VIN = VIN, nom, TA = 25 o C, ) Case 1: On/Off input is set to Logic Low (Module ON) and then input power is applied (delay from instant at which VIN =VIN, min until Vo=10% of Vo,set) Case 2: Input power is applied for at least one second and then the On/Off input is set to logic Low (delay from instant at which Von/Off=0.3V until Vo=10% of Vo, set) Output voltage Rise time (time for Vo to rise from 10% of Vo,set to 90% of Vo, set) All Tdelay 3 msec All Tdelay 3 msec All Trise 4 6 msec Output voltage overshoot Startup 1 % VO, set IO= IO, max; VIN = 8.3 to 14Vdc, TA = 25 o C Overtemperature Protection All Tref 140 C (See Thermal Consideration section) Input Undervoltage Lockout Turn-on Threshold All 7.9 V Turn-off Threshold All 7.8 V September 25, 2015 2015 General Electric Company. All rights reserved. Page 5
Characteristic Curves The following figures provide typical characteristics for the Austin MiniLynx TM 12 V SMT modules at 25ºC. 88 86 84 92 90 88 EFFICIENCY, η (%) 82 80 78 76 VIN = 8.3V 74 VIN = 12.0V 72 VIN =14.0V 70 0 0.6 1.2 1.8 2.4 3 OUTPUT CURRENT, IO (A) Figure 1. Converter Efficiency versus Output Current (Vout = 1.2Vdc). EFFICIENCY, η (%) 86 84 82 80 VIN = 8.3V 78 VIN =12.0V 76 VIN = 14.0V 74 0 0.6 1.2 1.8 2.4 3 OUTPUT CURRENT, IO (A) Figure 4. Converter Efficiency versus Output Current (Vout = 2.5Vdc). 88 95 EFFICIENCY, η (%) 86 84 82 80 78 76 VIN = 8.3V 74 VIN = 12.0V 72 VIN = 14.0V 70 0 0.6 1.2 1.8 2.4 3 OUTPUT CURRENT, IO (A) Figure 2. Converter Efficiency versus Output Current (Vout = 1.5Vdc). EFFICIENCY, η (%) 92 89 86 83 80 77 74 VIN = 8.3V VIN = 12.0V VIN = 14.0V 71 0 0.6 1.2 1.8 2.4 3 OUTPUT CURRENT, IO (A) Figure 5. Converter Efficiency versus Output Current (Vout = 3.3Vdc). 90 88 86 99 96 93 EFFICIENCY, η (%) 84 82 80 78 VIN = 8.3V 76 VIN = 12.0V 74 VIN = 14.0V 72 0 0.6 1.2 1.8 2.4 3 EFFICIENCY, η (%) 90 87 84 81 VIN = 8.3V 78 VIN = 12.0V 75 VIN =14.0V 72 0 0.6 1.2 1.8 2.4 3 OUTPUT CURRENT, IO (A) Figure 3. Converter Efficiency versus Output Current (Vout = 1.8Vdc). OUTPUT CURRENT, IO (A) Figure 6. Converter Efficiency versus Output Current (Vout = 5.0Vdc). September 25, 2015 2015 General Electric Company. All rights reserved. Page 6
Characteristic Curves (continued) The following figures provide typical characteristics for the Austin MiniLynx TM 12V SMT modules at 25ºC. INPUT CURRENT, IIN (A) 1.6 Io=3A 1.4 Io=1.5A 1.2 Io=0A 1 0.8 0.6 0.4 0.2 0 7 8 9 10 11 12 13 14 INPUT VOLTAGE, VIN (V) Figure 7. Input voltage vs. Input Current (Vout =3.3Vdc). OUTPUT CURRENT, OUTPUT VOLTAGE IO (A) (1A/div) VO (V) (200mV/div) TIME, t (5 µs/div) Figure 10. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo = 3.3Vdc). OUTPUT VOLTAGE VO (V) (10mV/div) TIME, t (1µs/div) Figure 8. Typical Output Ripple and Noise (VIN = 12.0V dc, Vo = 0.75Vdc, Io=3A). OUTPUT CURRENT, OUTPUT VOLTAGE IO (A) (1A/div) VO (V) (200mV/div) TIME, t (5 µs/div) Figure 11. Transient Response to Dynamic Load Change from 100% to 50% of full load (Vo = 3.3 Vdc). OUTPUT VOLTAGE VO (V) (10mV/div) TIME, t (1µs/div) Figure 9. Typical Output Ripple and Noise (VIN = 12.0V dc, Vo = 3.3Vdc, Io=3A). OUTPUT CURRENT, OUTPUT VOLTAGE IO (A) (2A/div) VO (V) (50mV/div) TIME, t (50µs/div) Figure 12. Transient Response to Dynamic Load Change from 50% to 100% of full load (Vo = 3.3 Vdc, Cext = 2x150 μf Polymer Capacitors). September 25, 2015 2015 General Electric Company. All rights reserved. Page 7
Characteristic Curves (continued) The following figures provide typical characteristics for the Austin MiniLynx TM 12 V SMT modules at 25ºC. OUTPUT CURRENT, OUTPUTVOLTAGE IO (A) (1A/div) VO (V) (50mV/div) TIME, t (100µs/div) Figure 13. Transient Response to Dynamic Load Change from 100% of 50% full load (Vo = 3.3Vdc, Cext = 2x150 μf Polymer Capacitors). INPUT VOLTAGE OUTPUT VOLTAGE VIN (V) (10V/div) VO (V) (1V/div) TIME, t (2ms/div) Figure 16. Typical Start-Up with application of Vin (VIN = 12.0Vdc, Vo = 3.3Vdc, Io = 3A). ON/OFF VOLTAGE OUTPUT VOLTAGE VOn/off(V) (10V/div) VO (V) (1V/div) TIME, t (2ms/div) Figure 14. Typical Start-Up Using Remote On/Off (VIN = 12.0Vdc, Vo = 3.3Vdc, Io = 3A). ON/OFF VOLTAGE OUTPUT VOLTAGE VOn/off(V) (10V/div) VO (V) (0.5V/div) TIME, t (2ms/div) Figure 17 Typical Start-Up Using Remote On/Off with Prebias (VIN = 12.0Vdc, Vo = 1.8Vdc, Io = 1.0A, Vbias =1.0Vdc). ON/OFF VOLTAGE OUTPUT VOLTAGE VOn/off(V) (10V/div) VO (V) (1V/div) TIME, t (2ms/div) Figure 15. Typical Start-Up Using Remote On/Off with Low- ESR external capacitors (7x150uF Polymer) (VIN = 12.0Vdc, Vo = 3.3Vdc, Io = 3A, Co = 1050µF). OUTPUT CURRENT, IO (A) (5A/div) TIME, t (10ms/div) Figure 18. Output short circuit Current (VIN = 12.0Vdc, Vo = 0.75Vdc). September 25, 2015 2015 General Electric Company. All rights reserved. Page 8
Characteristic Curves (continued) The following figures provide thermal derating curves for the Austin MiniLynx TM 12 V SMT modules. 3.5 3 3.5 3.0 OUTPUT CURRENT, Io (A) 2.5 2 1.5 1 0.5 100 LFM 0 LFM 0 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA O C Figure 19. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 12.0 Vdc, Vo=0.75Vdc). OUTPUT CURRENT, Io (A) 2.5 2.0 1.5 1.0 0.5 100 LFM 0 LFM 0.0 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA O C Figure 22. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 12 Vdc, Vo=5.0 Vdc). 3.5 3.0 OUTPUT CURRENT, Io (A) 2.5 2.0 1.5 1.0 100 LFM 0.5 0 LFM 0.0 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA O C Figure 20. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 12.0Vdc, Vo=1.8 Vdc). 3.5 3.0 OUTPUT CURRENT, Io (A) 2.5 2.0 1.5 1.0 0.5 100 LFM 0 LFM 0.0 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE, TA O C Figure 21. Derating Output Current versus Local Ambient Temperature and Airflow (VIN = 12.0Vdc, Vo=3.3 Vdc). Test Configurations September 25, 2015 2015 General Electric Company. All rights reserved. Page 9
TO OSCILLOSCOPE BATTERY LTEST 1μH CS 1000μF Electrolytic E.S.R.<0.1Ω @ 20 C 100kHz 2x100μF Tantalum CURRENT PROBE VIN(+) COM NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1μH. Capacitor CS offsets possible battery impedance. Measure current as shown above. Figure 23. Input Reflected Ripple Current Test Setup. COPPER STRIP CIN Design Considerations Input Filtering The Austin MiniLynx TM 12V SMT module should be connected to a low-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability in the presence of inductive traces that supply input voltage to the module. In a typical application, a 22 µf low-esr ceramic capacitors will be sufficient to provide adequate ripple voltage at the input of the module. To further minimize ripple voltage at the input, additional ceramic capacitors are recommended at the input of the module. Figure 26 shows input ripple voltage (mvp-p) for various outputs with 10µF and with a 22µF ceramic capacitor at full load. V O (+) COM 1uF. 10uF SCOPE RESISTIVE LOAD 350 300 250 1 x 10uF 1 x 22uF GROUND PLANE NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 24. Output Ripple and Noise Test Setup. Rdistribution Rcontact VIN(+) VO Rcontact Rdistribution 200 150 100 50 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 Figure 26. Input ripple voltage for various outputs with a 10 µf or a 22 µf ceramic capacitor at the input (full-load). VIN VO RLOAD Rdistribution Rcontact Rcontact Rdistribution COM COM NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 25. Output Voltage and Efficiency Test Setup. Efficiency η = V O. I O V IN. I IN x 100 % September 25, 2015 2015 General Electric Company. All rights reserved. Page 10
Design Considerations (continued) Output Filtering The Austin MiniLynx TM 12 V SMT module is designed for low output ripple voltage and will meet the maximum output ripple specification with 1 µf ceramic and 10 µf tantalum capacitors at the output of the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. Safety Considerations For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE 0850:2001-12 (EN60950-1) Licensed. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR polymer and ceramic capacitors are recommended to improve the dynamic response of the module. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. The input to these units is to be provided with a fast-acting fuse with a maximum rating of 6A in the positive input lead. September 25, 2015 2015 General Electric Company. All rights reserved. Page 11
Feature Description Remote On/Off Austin MiniLynx TM 12V SMT power modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available in the Austin MiniLynx TM 12V series modules. Positive Logic On/Off signal, device code suffix 4, turns the module ON during a logic High on the On/Off pin and turns the module OFF during a logic Low. Negative logic On/Off signal, no device code suffix, turns the module OFF during logic High and turns the module ON during logic Low. For positive logic modules, the circuit configuration for using the On/Off pin is shown in Figure 27. The On/Off pin is an open collector/drain logic input signal (Von/Off) that is referenced to ground. During a logic-high (On/Off pin is pulled high internal to the module) when the transistor Q1 is in the Off state, the power module is ON. Maximum allowable leakage current of the transistor when Von/off = VIN,max is 10µA. Applying a logic-low when the transistor Q1 is turned-on, the power module is OFF. During this state VOn/Off must be less than 0.3V. When not using positive logic On/off pin, leave the pin unconnected or tie to VIN. VIN+ ON/OFF + V ON/OFF I ON/OFF GND Q1 _ R1 R2 R3 R4 Q2 MODULE PWM Enable Q3 CSS Figure 27. Circuit configuration for using positive logic On/OFF. VIN+ ON/OFF GND R pull-up I ON/OFF + V ON/OFF Q1 _ R1 R2 MODULE PWM Enable Q2 CSS Figure 28. Circuit configuration for using negative logic On/OFF. Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The typical average output current during hiccup is 3.5A. Input Undervoltage Lockout At input voltages below the input undervoltage lockout limit, module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. Overtemperature Protection To provide over temperature protection in a fault condition, the unit relies upon the thermal protection feature of the controller IC. The unit will shutdown if the thermal reference point Tref2, (see Figure 31) exceeds 140 o C (typical), but the thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. The module will automatically restarts after it cools down. For negative logic On/Off devices, the circuit configuration is shown is Figure 28. The On/Off pin is pulled high with an external pull-up resistor (typical Rpull-up = 68k, +/- 5%). When transistor Q1 is in the Off state, logic High is applied to the On/Off pin and the power module is Off. The minimum On/off voltage for logic High on the On/Off pin is 2.5 Vdc. To turn the module ON, logic Low is applied to the On/Off pin by turning ON Q1. When not using the negative logic On/Off, leave the pin unconnected or tie to GND. September 25, 2015 2015 General Electric Company. All rights reserved. Page 12
Feature Descriptions (continued) Output Voltage Programming The output voltage of the Austin MiniLynx TM 12V can be programmed to any voltage from 0.75Vdc to 5.5Vdc by connecting a resistor (shown as Rtrim in Figure 29) between Trim and GND pins of the module. Without an external resistor between Trim and GND pins, the output of the module will be 0.7525Vdc. To calculate the value of the trim resistor, Rtrim for a desired output voltage, use the following equation: 10500 Rtrim = 1000 Vo 0.7525 Ω Rtrim is the external resistor in Ω Vo is the desired output voltage For example, to program the output voltage of the Austin MiniLynx TM 12V module to 1.8V, Rtrim is calculated as follows: 10500 Rtrim = 1000 1.8 0.7525 Rtrim = 9. 024kΩ helps determine the required external trim resistor needed for a specific output voltage. Voltage Margining Output voltage margining can be implemented in the Austin MiniLynx TM modules by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to the Output pin for margining-down. Figure 30 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.gecriticalpower.com under the Design Tools section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local GE technical representative for additional details. Vo Austin Lynx or Lynx II Series Trim Q2 Rmargin-down Rmargin-up V IN (+) V O (+) Rtrim Q1 ON/OFF TRIM LOAD GND GND R trim Figure 30. Circuit Configuration for margining Output voltage. Figure 29. Circuit configuration to program output voltage using an external resistor. Table 1 provides Rtrim values required for some common output voltages. Table 1 VO, set (V) Rtrim (KΩ) 0.7525 Open 1.2 22.46 1.5 13.05 1.8 9.024 2.5 5.009 3.3 3.122 5.0 1.472 Using 1% tolerance trim resistor, set point tolerance of ±2% is achieved as specified in the electrical specification. The POL Programming Tool, available at www.gecriticalpower.com under the Design Tools section, September 25, 2015 2015 General Electric Company. All rights reserved. Page 13
Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 32. Note that the airflow is parallel to the long axis of the module as shown in figure 31. The derating data applies to airflow in either direction of the module s long axis. Wind Tunnel PWBs x 25.4_ (1.0) 76.2_ (3.0) Power Module 5.97_ (0.235) Air flow Probe Location for mea suring a irflow a nd ambient temperature Figure 32. Thermal Test Set-up. Heat Transfer via Convection Figure 31. Tref Temperature measurement location. Increased airflow over the module enhances the heat transfer via convection. Thermal derating curves showing the maximum output current that can be delivered by various module versus local ambient temperature (TA) for natural convection and up to 0.5m/s (100 ft./min) are shown in the Characteristics Curves section. The thermal reference point, Tref used in the specifications is shown in Figure 32. For reliable operation this temperature should not exceed 115 o C. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note Thermal Characterization Process For Open-Frame Board-Mounted Power Modules for a detailed discussion of thermal aspects including maximum device temperatures. September 25, 2015 2015 General Electric Company. All rights reserved. Page 14
Mechanical Outline Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) Bottom View Co-planarity (max): 0.102 [0.004] Side View PIN FUNCTION 1 On/Off 2 VIN 3 GND 4 Trim 5 VOUT September 25, 2015 2015 General Electric Company. All rights reserved. Page 15
Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) PIN FUNCTION 1 On/Off 2 VIN 3 GND 4 Trim 5 VOUT September 25, 2015 2015 General Electric Company. All rights reserved. Page 16
Packaging Details The Austin MiniLynx TM 12 V SMT version is supplied in tape & reel as standard. Modules are shipped in quantities of 400 modules per reel. All Dimensions are in millimeters and (in inches). Reel Dimensions Outside diameter: 330.2 mm (13.00) Inside diameter: 177.8 mm (7.00 ) Tape Width: 44.0 mm (1.73 ) September 25, 2015 2015 General Electric Company. All rights reserved. Page 17
Surface Mount Information Pick and Place The Austin MiniLynx TM 12 V SMT modules use an open frame construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and placing. The label meets all the requirements for surface mount processing, as well as safety standards and is able to withstand maximum reflow temperature. The label also carries product information such as product code, serial number and location of manufacture. soldering the solder reflow profile should be established by accurately measuring the modules CP connector temperatures. REFLOW TEMP ( C) REFLOW TIME (S) Figure 34. Reflow Profile for Tin/Lead (Sn/Pb) process. Figure 33. Pick and Place Location. Nozzle Recommendations The module weight has been kept to a minimum by using open frame construction. Even so, these modules have a relatively large mass when compared to conventional SMT components. Variables such as nozzle size, tip style, vacuum pressure and pick & placement speed should be considered to optimize this process. The minimum recommended nozzle diameter for reliable operation is 3mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 8 mm max. Tin Lead Soldering MAX TEMP SOLDER ( C) Figure 35. Time Limit Curve Above 205 o C Reflow for Tin Lead (Sn/Pb) process. The Austin MiniLynx TM 12V SMT power modules are lead free modules and can be soldered either in a lead-free solder process or in a conventional Tin/Lead (Sn/Pb) process. It is recommended that the customer review data sheets in order to customize the solder reflow profile for each application board assembly. The following instructions must be observed when soldering these units. Failure to observe these instructions may result in the failure of or cause damage to the modules, and can adversely affect long-term reliability. In a conventional Tin/Lead (Sn/Pb) solder process peak reflow temperatures are limited to less than 235 o C. Typically, the eutectic solder melts at 183 o C, wets the land, and subsequently wicks the device connection. Sufficient time must be allowed to fuse the plating on the connection to ensure a reliable solder joint. There are several types of SMT reflow technologies currently used in the industry. These surface mount power modules can be reliably soldered using natural forced convection, IR (radiant infrared), or a combination of convection/ir. For reliable September 25, 2015 2015 General Electric Company. All rights reserved. Page 18
Surface Mount Information (continued) Lead Free Soldering The Z version Austin MiniLynx 12V SMT modules are leadfree (Pb-free) and RoHS compliant and are both forward and backward compatible in a Pb-free and a SnPb soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. C (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Figure. 36. MSL Rating The Austin MiniLynx 12V SMT modules have a MSL rating of 2a. Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of <= 30 C and 60% relative humidity varies according to the MSL rating (see J-STD-033A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40 C, < 90% relative humidity. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power Modules: Soldering and Cleaning Application Note (AN04-001). Reflow Temp ( C) 300 Per J-STD-020 Rev. C Peak Temp 260 C 250 200 150 100 50 0 Heating Zone 1 C/Second * Min. Time Above 235 C 15 Seconds *Time Above 217 C 60 Seconds Reflow Time (Seconds) Cooling Zone Figure 36. Recommended linear reflow profile using Sn/Ag/Cu solder. September 25, 2015 2015 General Electric Company. All rights reserved. Page 19
Ordering Information Please contact your GE Sales Representative for pricing, availability and optional features. Table 3. Device Codes Device Code Input Voltage Output Voltage Output Current Efficiency 3.3V@ 3A On/Off Logic Connector Type Comcodes AXA003A0X-SR 8.3 14Vdc 0.75 5.5Vdc 3 A 89.0 % Negative SMT 108991213 AXA003A0X4-SR 8.3 14Vdc 0.75 5.5Vdc 3 A 89.0 % Positive SMT 108991221 AXA003A0X-SRZ 8.3 14Vdc 0.75 5.5Vdc 3 A 89.0 % Negative SMT CC109101276 AXA003A0X4-SRZ 8.3 14Vdc 0.75 5.5Vdc 3 A 89.0 % Positive SMT CC109102266 -Z refers to RoHS compliant Versions Contact Us For more information, call us at USA/Canada: +1 877 546 3243, or +1 972 244 9288 Asia-Pacific: +86.021.54279977*808 Europe, Middle-East and Africa: +49.89.878067-280 www.gecriticalpower.com GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. September 25, 2015 2015 General Electric Company. All International rights reserved. Version 1.4