Installation Instructions Monitor Roll Stand w w w. a m i c o. c o m
Preface Important, Please Read Carefully Thank you for your purchase with Amico. This unit is designed for long lasting performance, providing the end user complies with assembly and maintenance procedures. This Instruction Manual is your guide to ensure that you get the best performance out of the equipment. Amico Accessories Inc. is not responsible for any damage as a result of (but not limited to) abuse and other problems that may be a direct or indirect result of failure to comply with the instructions provided in this manual. Please note these key words and symbols: WARNING Steps where extra care should be taken to prevent injuries and damage NOTE Steps that point out helpful information Medical Facility Responsibilities Preventive maintenance checks must be performed regularly to maintain the quality and performance of this product. Any parts that may be broken, missing, worn, distorted or contaminated in any way should not be used and all affected parts should be replaced immediately. Should the necessity of any repair be suspected; please contact your local distributor. 1 Amico Accessories Inc.
Table of Contents Installation Preparation Installation Parts Requirements 3-4 Installation Tools Requirements 5 Installation of Rollstand Roll Stand Assembly (Roll Stand Base Assembly) 6 Roll Stand Installation (Monitor Head Installation) 7 Installation of Accessories Basket Installation 8 Handle Installation 9 Warranty Information 10 www.amico.com 2
Installation Parts Requirements The list below includes all parts required for installation. Please check the contents of your Roll Stand Package to ensure all parts are included. If any hardware or parts are missing, please contact Amico Accessories Inc. Roll Stand Base Basket Handle Package (Brown Box) Roll Stand Casters and Hardware Kit 1 Monitor Head (PM5 shelf shown) (Right), Hardware Kit 2 Roll Stand Post Hardware Kit 1 contents Hardware Kit 2 contents 3 Amico Accessories Inc.
Installation Parts Requirements The picture below shows what is included in the box. Picture is for reference only, you may receive different contents or the box layout could be different when received. Basket Head Assembly, Castors, and Hardware Packages Handle Package Roll Stand Post Roll Stand Base www.amico.com 4
Installation Tools Requirements The table below lists all the tools required for installation. NOTE: Please ensure that your contents match the list as outlined on the previous pages. If not, please contact Amico Accessories Inc. at 1-877-264-2697 1. HEX Key 3/16" (47.6 mm) NOT PROVIDED 2. Philips Screw Driver (Star head) NOT PROVIDED 3. Socket Wrench (1/2" [1.27 cm] Socket) NOT PROVIDED 4. 1/2" (1.27 cm) Wrench 1 A: Tools 2 3 4 5 Amico Accessories Inc.
Roll Stand Installation (Roll Stand Base Assembly) NOTE: Figure 2 is an exploded view of the Roll Stand base assembly. NOTE: DO NOT use a hammer on the casters or the Roll Stand post. 1. Hardware Kit 1 has the necessary hardware for the instructions in this section. (Figure 1) 2. Push locking casters into the base by hand until it clicks in place. Repeat for all 5 casters. 3. Insert the end of the Roll Stand post with the bushing into the Roll Stand base. Secure the post to the Roll Stand by inserting the long bolt, through the lock washer, and then the large washer through the base, into the Roll Stand post and tighten with ½" wrench. Ensure all connections are secured. (Figure 2) Long Bolt Large Washer (Silver) Casters Roll Stand Post Roll Stand Bushing Lock Washer Hardware Kit 1 Figure 1 Casters Large Washer Lock Washer Long Bolt Figure 2 www.amico.com 6
Roll Stand Installation (Monitor Head Installation) WARNING: The Roll Stand Monitor Head is rated for up to 20 lbs (9.07 kg). Ensure that the monitor being mounted does not exceed this weight. WARNING: Ensure that there is no gap between the large plastic bushing and the monitor head after assembly. 1. Hardware Package 2 (packaged with selected monitor head) has the hardware necessary for the instructions in this section. 2. Place the adapter on the top of the post, ensure the side with the lip is facing up 3. Place the large black plastic bushing on top of the adapter, fitting the lip of the adapter. 4. Place the small plastic bushing inside the bottom of the monitor head, and place the monitor head assembly into the adapter. 5. Insert the nylon washer and then the bronze washer into the recessed hole on the top of the head. Next, insert the head bolt through the two washers, into the hole in the head and tighten using the 1/2 (1.27 cm) wrench. Tighten the head bolt until there is no gap between the large black plastic bushing and the adapter. (Figure 3) 6. Place the doming label in the recessed slot on the head to cover the screw. Large plastic bushing Small plastic bushing Adapter Doming Label Head Bolt Bronze Washer Nylon Washer Head Bolt (bolt will have threadlock) Monitor Head (PM 5 shelf shown) Doming Label Bronze Washer Nylon Washer Hardware Package 2 Lip faces up Small Black Plastic Bushing Large Black Plastic Bushing Ensure there is no gap between here Adapter Figure 3 Roll Stand Post 7 Amico Accessories Inc.
Basket Installation WARNING: DO NOT tighten one screw all the way into the clamp assembly without tightening the other. Only tighten the first screw after the second screw is at least half way into the clamp assembly or the clamp may be damaged. (Figure 4) WARNING: DO NOT overtighten the screws as this may strip the thread. WARNING: The basket is rated for up to 10 lbs (4.547 kg). Ensure the load that is placed in the basket does not exceed this weight. 1. Remove the clamp devices from the basket assembly using the 3/16" (47.6 mm) HEX Key, and place the clamp assembly at the desired height on the Roll Stand post. 2. Line the holes of the top clamp assembly on the basket with the holes on the clamp device. Partially secure one of the two bolts BUT DO NOT TIGHTEN, then partially secure the second bolt. Once both bolts are started, partially secure the bolts in the bottom clamp assembly in the same way. Once all four bolts are partially secured, Tighten in a CROSS Pattern. (Figure 5 and 6) Clamp Device Roll Stand Post INCORRECT Clamp Assembly on Basket Figure 4 CORRECT Clamp Device Clamp Assembly 3/16 (47.6 mm) HEX Bolt Roll Stand Post Basket Double Clamp Basket Sample Figure 5 Tighten using Cross Pattern Figure 6 www.amico.com 8
Handle Installation WARNING: DO NOT tighten one screw all the way in the clamp device without the other. Only tighten the first screw after the second screw is at least half way into the clamp assembly or the clamp maybe damaged. (Figure 7) WARNING: Ensure the clamp device is the correct side up. The rounded edge of the clamp faces up while the more squared edge faces down. The finished side of the handle faces up. (Figure 8) 1. Place the clamp device at the desired height on the Roll Stand post. 2. Line up the holes up on the handle with the holes on the clamp device. Start one of the two HEX bolts BUT DO NOT TIGHTEN, then start the second bolt. Once both bolts are started, tighten the bolts. (Figure 9) Clamp Assembly Roll Stand Post UP (more rounded edges) INCORRECT Clamp Assembly on Clamp Figure 7 CORRECT DOWN (more squared edges) Figure 8 Clamp Device Roll Stand Handle 3/16 Hex Bolt Roll Stand Post Figure 9 9 Amico Accessories Inc.
Accessories Warranty Policy Amico Accessories warrants all mounting accessories to be free from defects in material and workmanship for a period of twelve (12) months from the date of shipment. Within this period Amico Accessories will repair or replace any part which is proven to be defective. We don t just send parts and pieces, we replace the product! Amico Accessories will warrant its material to be free from defect for an additional period of four (4) years, five (5) years from the date of shipment. Within this period, Amico Accessories will replace any part at no charge, which is proven to be defective. Shipping and Installation costs after the first twelve (12) months will be borne by the customer. This warranty is valid only when the product has been properly installed according to Amico Accessories specifications, used in a normal manner and serviced according to factory recommendations. It does not cover products that are not manufactured by Amico Accessories. It does not cover failures due to damage which occurs in shipments or failures which resulted from accidents, misuse, abuse, neglect, mishandling, alteration, misapplication or damage that may be attributable to acts of God. Amico Accessories shall not be liable for incidental or consequential damages resulting from use of equipment. All claims for warranty must first be approved by Amico Accessories. A valid Return Goods Authorization (RGA) number must be obtained from Amico Accessories prior to commencement of any service work. Warranty work, which has not been preauthorized by Amico Accessories, will not be reimbursed. AMICO ACCESSORIES DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY. The distributor and/or dealer are not sanctioned to create verbal warranties about the product described in this agreement. Any statements will not be honored or be made part of the agreement of sale. This document is the final complete and exclusive terms of the agreement. THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES. Amico Accessories shall not, under any circumstances be liable for incidental or consequential damages including, but not limited to, profit, loss of sales or injuries to person(s) or property. Correction of noncompliance as noted above will result in completion of all liabilities of Amico Accessories, whether based on agreement, neglect or changed materials, designs or specifications without notice. All claims for warranty must first be approved by Amico Accessories Service Department: accessories@amico.com or 1.877.264.2697). A valid Return Goods Authorization number must be obtained from Amico Accessories prior to commencement of any warranty claim.
www.amico.com Amico Accessories Inc. www.amico.com 85 Fulton Way, Richmond Hill Ontario, L4B 2N4, Canada 71 East Industry Court, Deer Park NY 11729, U.S.A Toll Free Tel: 1.877.264.2697 Toll Free Fax: 1.866.440.4986 Tel:905.763.7778 Fax:905.763.8587 Email: info@amico.com AA-IM-MNTR-RLSTD 10.21.2014