CREATE YOUR STYLE MINI PROJECTS St. Patrick s Day
Irish Flag Pendant Necklace Color Color Code Fern Green 291 White Alabaster 281 Sun 248 70 pcs. 30 pcs. 5 mm 2 Silver headpins (9) Silver Lobster clasp (1) 6 mm silver jump ring (2) 4 24 gauge silver wire Silver crimp covers (4) 2x2 crimp beads (4) 30 beading wire STEP 1: String 9 XILION Bicone article Fern Green from the SWAROVSKI ELEMENTS assortment onto one headpin. Turn a loop at the top of the headpin. Repeat two more times. STEP 2: Repeat step 1 using the Swarovski XILION Bead White Alabaster and then repeat again using the XILION Bead Sun. STEP 3: String 10 Swarovski XILION Bead onto the 24 gauge wire alternating each bead with one of the beaded headpins made in steps 1 and 2. Start with the Fern Green, then add the White Alabaster in the middle and the Sun at the other end. Link the headpins on the wire with the loop made at the top of each headpin. When the necklace is worn, the Fern Green needs to be to the right. Continuation on next page
Irish Flag Pendant Necklace, page 2 STEP 4: Make a loop on both ends of the beaded wire from step 3. STEP 5: Cut the beading wire in half. String one piece of wire through one loop formed in the wire in step 4. Add a crimp bead and string the beading wire over the loop and back through the crimp bead. Crimp the bead to secure. Attach a crimp cover over the crimped bead. STEP 6: String on 5 Swarovski XILION article and then add 3 XILION 5 mm. Repeat this step 4 times and add 5 more XILION. STEP 7: String beaded wire end through a crimp bead, then through the 6 mm jump ring and back through the crimp bead. Pull to take up slack in wire, but make sure the beads are not too tight the beaded wire should be flexible. Crimp the crimp bead to secure and cover with crimp cover. STEP 8: Repeat steps 6 and 7 for the other side of necklace. Open the jump ring and attach the lobster clasp. Close the jump ring to secure.
Irish Flag Bracelet 6 mm Fern Green 291 6 mm White Alabaster 281 6 mm Sun 248 1 pc. 2 Tierra Cast 3 to 1 Connector (94-3055) 2 headpin (1) 2x2 crimp beads (6) Magnetic Clasp (1) 30 beading wire 6 mm jump rings (2) STEP 1: Cut wire into 3 equal pieces. STEP 2: String one wire end through a crimp bead then through an end loop in the Tierra Cast 3 to 1 connector and back through the crimp bead. Crimp the crimp bead to secure wire. STEP 3: String on 9 XILION Bicone article 6 mm Sun from the SWAROVSKI ELEMENTS assortment. Next, string on 9 Swarovski XILION in White Alabaster. Finally string on 9 Swarovski XILION in Fern Green. Continuation on next page
Irish Flag Bracelet, page 2 STEP 4: Then attach the crimp to the corresponding loop on the opposite Tierra Cast 3-1 connector. Crimp the bead to secure the wire. STEP 5: Repeat steps 2 4 two more times to create all three strands of bracelet. STEP 6: Slide the Swarovski Clover Bead article to the headpin. Turn a loop on the headpin near the top of the Clover Bead. Attach to one wire end and make sure loop is securely closed. STEP 7: Attach magnetic clasps to both end of 3 to 1 connector with jump rings.
Celtic Clover Necklace 34 pcs. Fern Green 291 1 6 mm Fern Green 291 1 6 pcs. 1 Tierra Cast Celtic Square Bead (94-5524) 2x2 crimp beads (2) 6 mm jump rings (2) 4 Tierra Cast Celtic Diamond Bead (94-5526) Lobster Clasp (1) 30 beading wire STEP 1: String beading wire through a crimp bead, through a jump ring and back through the crimp bead. Crimp the bead to secure the wire. STEP 2: String on the following one Swarovski XILION Bicone Bead article Fern Green, one XILION Bead 6 mm Fern Green, one XILION Bead Fern Green, one Clover Bead article, one XILION Bead, one Clover Bead, one XILION Bead, one Clover Bead, one XILION Bead, one XILION Bead 6 mm, one XILION Bead and one Tierra Cast Celtic Diamond Bead. STEP 3: Repeat step 2 two more times, but the second time omit the last XILION Bead and add one Tierra Cast Celtic Square Bead instead of the Celtic Diamond Bead. STEP 4: Reverse pattern starting with the XILION Bead 6 mm to complete other side of necklace. STEP 5: Repeat step 1 to finish necklace. Open jump ring and add lobster clasp. Close jump ring securely.
Clover Cross Earrings 2 Tierra Cast Small Celtic Cross (94-2089) 24 gauge 2 headpins French Ear wires (2) STEP 1: Center the Clover Bead article from the SWAROVSKI ELEMENTS assortment on one headpin. Bend head pin on both sides to secure Bead in center. STEP 2: Attach one end of headpin to loop in bottom of ear wire, turn a loop and wrap wire around headpin. STEP 3: Repeat step 2 using the loop in the top of the Tierra Cast Small Celtic Cross. STEP 4: Repeat steps 1-3 to complete other earring.
Clover Drop Earrings Sun 248 Emerald or Fern Green 205 or 291 2 Tierra Cast Clover pendant (94-2219) 24 gauge 3 headpins (2) French Ear wires (2) STEP 1: Using one of the head pins, string on one Clover Bead article Emerald (or Fern Green) from the SWAROVSKI ELEMENTS assortment, one XILION Bead article Sun and one Clover Bead. STEP 2: Center Swarovski on headpin. Bend head pin on both sides to secure in center. STEP 3: Attach one end of head pin to loop in bottom of ear wire, turn a loop and wrap wire around head pin. STEP 4: Repeat step 3 using the loop in the top of the Tierra Cast Clover pendant. STEP 5: Repeat steps 1-4 to complete other earring.
Clover Drop Bracelet 4 pcs. Emerald or Fern Green 205 or 291 Sunflower 292 Emerald or Fern Green 205 or 291 Sunflower 292 2 Tierra Cast Clover small Celtic Cross (94-2089) 24 gauge 2 head pins (16) 6 mm jump rings (5) 1 Tierra Cast Medium Celtic Cross (94-2193) 7 Chain Silver lobster clasp (1) STEP 1: Attach all SWAROVSKI ELEMENTS to headpins. STEP 2: Turn a loop on all headpins near the top of all. STEP 3: Attach the three 6 mm jump rings to the three Tierra Cast Celtic Cross pendants. STEP 4: Attach all beaded headpins by wire wrapping in place and Celtic Cross pendants to the chain in random order skipping one to three links in between each depending type of chain. STEP 5: Open both jump rings. Attach to both ends of chain. Attach lobster clasp to one jump ring. Close both jump rings to secure.