HLG1HC series Ⅰ IP65 IP67 ~ A File Name:HLG1HCSPEC 160613
HLG1HC series SPECIFICATION MODEL HLG1HC350 HLG1HC500 HLG1HC700 HLG1HC1050 HLG1HC1400 RATED CURRENT 350mA 500mA 700mA 1050mA 1400mA RATED POWER 150.5W 150W 150.5W 155.4W 151.2W CONSTANT CURRENT REGION Note.2 215 ~ 430V 150V ~ 300V 107V ~ 215V 74V ~ 148V 54V ~ 108V OUTPUT Adjustable for AType only (via builtin potentiometer) CURRENT ADJ. RANGE 175 ~ 350mA 250 ~ 500mA 350 ~ 700mA 525 ~ 1050mA 700 ~ 1400mA CURRENT RIPPLE 8.0% max. @rated current CURRENT TOLERANCE ±5% SET UP TIME Note.4 1000ms / 115VAC 500ms / 230VAC VOLTAGE RANGE Note.3 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF 0.9 8/ 115VAC, PF 0.96/230 VAC, PF 0.93/277VAC @ full load (Please refer to " POWER FACTOR (PF) CHARACTERISTIC" section) THD< % (@ load 50% /115VAC, 230VAC; @ load 75%/277VAC) TOTAL HARMONIC DISTORTION INPUT (Please refer to TOTAL HARMONIC DISTORTION (THD) section) EFFICIENCY (Typ.) AC CURRENT (Typ.) 94% 1.6A / 115VAC 94% 0.8 A / 230VAC 94% 0.7A / 277VAC 94% 93.5% INRUSH CURRENT(Typ.) MAX. No. of PSUs on 16A CIRCUIT BREAKER COLD START 50A(t width=600 μs measured at 50% I peak) at 230VAC; Per NEMA 410 4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE 475 ~ 495V 335 ~ 355V 240 ~ 260V 165 ~ 175V 1 ~ 130V Shut down o/p voltage with autorecovery or repower on to recovery OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. Tcase=40 ~ 90 (Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase=90 ENVIRONMENT WORKING HUMIDITY 10 ~ 95% RH noncondensing STORAGE TEMP., HUMIDITY 40 ~ 80, 10 ~ 95% RH TEMP. COEFFICIENT VIBRATION ± 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.6 UL8750, CSA C22.2 No. 250.1312, ENEC EN613471, EN61347213, EN62384 independent, IP65 or IP67, J613471, J61347213 approved WITHSTAND VOLTAGE I/PO/P:3.75KVAC I/PFG:2KVAC O/PFG:1.5KVAC SAFETY & ISOLATION RESISTANCE I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH EMC EMC EMISSION Note.6 Compliance to EN55015, EN6100032 Class C (@ load 50% ) ; EN6100033 OTHERS NOTE EMC IMMUNITY Compliance to EN6100042,3,4,5,6,8,11, EN61547, light industry level (surge immunity LineEarth 4KV, LineLine 2KV) MTBF 652.2K hrs min. Telcordia SR332 (Bellcore) ; 191.1K hrs min. MILHDBK217F (25 ) DIMENSION 2*68*38.8mm (L*W*H) PACKING 1.04Kg; 12pcs/13.5Kg/0.8CUFT File Name:HLG1HCSPEC 160613
HLG1HC series BLOCK DIAGRAM PFC fosc : 70KHz PWM fosc : 60KHz I/P FG EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS & FILTER O.L.P. DETECTION CIRCUIT V V DIM DIM (B Type) O.V.P. DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. 100 In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN WELL. Vo(%) Constant Current region 50 100 Io (%) Typical output current normalized by rated current (%) File Name:HLG1HCSPEC 160613
HLG1HC series DIMMING OPERATION FG (Green/Yellow) AC/L(Brown) AC/N(Blue) HLG1HC BType DIM(Blue) DIM(White) V(Black) V(Red) 3 in 1 dimming function (for BType) Output constant current level can be adjusted by applying one of the three methodologies between DIM and DIM: 1 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100μA (typ.) Applying additive 1 ~ 10VDC V V DIM DO NOT connect "DIM to V" Additive Voltage Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 10% % 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input DIM Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): V V DIM Additive PWM signal DIM DO NOT connect "DIM to V" Applying additive resistance: V V DIM Additive Resistance DIM DO NOT connect "DIM to V" Output current (%) 100% 90% 80% 70% 60% 50% 40% 30% % 10% 10K/N K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance File Name:HLG1HCSPEC 160613
HLG1HC series Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options. N FG L Relay Switch Adjuster 10K/N~100K/N Ohms resistance 1~10V DC Voltage 10V PWM Signal Green/ Yellow Brown Blue AC/L AC/N HLG1HC BType DIM DIM V() V() Blue White Black Red LED Lighting Fixture Using a switch and relay can turn ON/OFF the lighting fixture. File Name:HLG1HCSPEC 160613
HLG1HC series OUTPUT LOAD vs TEMPERATURE 100 100 80 Others C500,C700 80 Others C500,C700 60 60 LOAD (%) LOAD (%) 40 AMBIENT TEMPERATURE,Ta ( ) Tcase ( ) STATIC CHARACTERISTIC 100 90 80 70 60 50 40 40 10 0 15 30 50 60 70 (HORIZONTAL) PF LOAD (%) 1 0.98 0.96 0.94 0.92 0.9 0.88 0.86 40 40 0 25 35 45 60 75 90(HORIZONTAL) POWER FACTOR (PF) CHARACTERISTIC Tcase at 80 277V 230V 115V 90 100 125 135 145 155 165 175 180 0 230 305 INPUT VOLTAGE (V) 60Hz 0.84 50% 60% 70% 80% 90% 100% LOAD (150W) TOTAL HARMONIC DISTORTION (THD) 700mA Model, Tcase at 80 EFFICIENCY vs LOAD HLG1HC series possess superior working efficiency that up to 94% can be reached in field applications. 700mA Model, Tcase at 80 25 95 THD(%) 15 10 5 0 50% 60% 70% 80% 90% 100% 277VAC 230VAC 115VAC EFFICIENCY(%) 92 89 86 83 80 77 74 10% % 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V LOAD LOAD File Name:HLG1HCSPEC 160613
HLG1HC series LIFE TIME 1 100 LIFETIME(Kh) 80 60 40 0 30 40 50 60 70 80 90 Tc a s e ( ) File Name:HLG1HCSPEC 160613
HLG1HC series MECHANICAL SPECIFICATION AType Case No.994 Unit:mm 12 9.6 2 196 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) 3C 9.4 34.2 9.4 68 34 tc : Max. Case Temperature tc 98 Io ADJ. V(Black) V(Red) STW 16AWG 2C(for HLG1HC350) 2C(for others) ψ 4.2 4PL 38.8 BType 2 12 196 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) 3C 9.6 9.4 34.2 9.4 68 34 tc : Max. Case Temperature tc 98 2C DIM(Blue) DIM(White) V(Black) V(Red) STW 16AWG 2C(for HLG1HC350) 2C(for others) ψ 4.2 4PL 38.8 DType 2 12 196 9.6 FG (Green/Yellow) AC/L(Brown) AC/N(Blue) 3C 9.4 34.2 9.4 68 34 tc tc : Max. Case Temperature 98 V(Black) V(Red) STW 16AWG 2C(for HLG1HC350) 2C(for others) ψ 4.2 4PL 38.8 File Name:HLG1HCSPEC 160613
HLG1HC series WATERPROOF CONNECTION Waterproof connector Waterproof connector can be assembled on the output cable of HLG1HC to operate in dry/wet/damp or outdoor environment. AC source I/P HLG1HC O/P Size Pin Configuration (Female) Size Pin Configuration (Female) M12 Order No. Suitable Current 4PIN 5A/PIN M1204 10A max. 5PIN 5A/PIN M1205 10A max. M15 Order No. Suitable Current 2PIN 12A/PIN M1502 12A max. LED Lamp Cable Joiner 66 26 CJ041 suitable for 14AWG~16AWG CJ042 suitable for 18AWG~22AWG ψ25 Up to four wires can be connected through this cable joiner by soldering or clamping by tools. LED Lamp HLG1HC O/P Wires CJ04 cable joiner can be purchased independently for user's own assembly. MEAN WELL order No. : CJ041, CJ042. INSTALLATION MANUAL Please refer to : http://www.meanwell.com/webnet/search/installationsearch.html File Name:HLG1HCSPEC 160613
Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Mean Well: HLG1HC350B HLG1HC500A HLG1HC1400A HLG1HC1050A HLG1HC1050B HLG1H C700B HLG1HC350A HLG1HC500B HLG1HC1400B HLG1HC700A