Installation Instructions for Wood Windows and Balcony Doors oto NT HOPPE North America, Inc. 05 E. Blackhawk Drive Fort Atkinson, WI 558-8 90-5- 90-5-4408 HOPPE North America, Inc. 45 Netherhart oad, Unit # Mississauga, ON 5T B8 CANADA 905-54-744 905-54-70 800-485-4885 info@us.hoppe.com www.us.hoppe.com Dated: November 004. We reserve the right to changes w ithout prior notice. Page ev 0-09/0 / AB 50- GB
Introduction locking-cam versions The oto NT hardware system offers different locking cam versions that differ in application and adjusting capabilities. For better orientation, the different versions in the part lists are highlighted in a red square. ocking cam E gasket compression adjustable cam ocking cam P gasket compression adjustable security cam ocking cam V height and gasket compression adjustable security cam For select products only The NT striker concept. All strikers in the oto NT hardware system have identical screwing-axes. This concept renders the prefitting of the sash with security cams possible, and a later frame retrofitting with security strikers (zinc or steel). All locking cam versions are combinable with all strikers. Cover caps. Upon request, all visible hinge components can be equipped with cover caps from the extensive oto range. Numerous colored versions are available. The surface finish. otosil the silver-colored surface finish. Optimal protection by means of galvanizing, chromating and additional sealing. Increased corrosion protection.
Basic Security Tilt&Turn /8-9 Hardware Overview 7 7 9 8 5 0 4 7 7 8 4 See HOPPE Window Handles at www.us.hoppe.com 5 7 NOTE: Mushroom cam required on this corner. 7 On S..H. < 500mm the tilt-range must be limited to 80mm!
Basic Security Tilt&Turn /8-9 Hardware Parts ist Application range Sash rebate width...90-00mm ) Sash rebate height...80-400mm Sash weight...max. 0kg (Up to 50kg with upgraded components at positions 8 and ) Centered/variable handle height T&T espagnolette, 5mm backset Sash rebate Handle height Espagnolette Material height length 0 450 ) 55 5 40 905 45 0 4 ) 5 0 400 800 400 580 E 80 00 40 00 980 E 0 00 0 800 80 E 0 000 80 000 780 E 00 400 00 00 80 4 E 9054 90559 9057 90575 9058 9059 Bullet catch cam (S..H. > 0mm) 098 Corner drive (not depicted) E 0087 Corner drive P 944 4 Special corner drive (not depicted) E (S..H. < 0mm) 944 (S..H. < 0mm) Special corner drive P 945 5 Sash stay guide Sash rebate Description / length Material width 90 40 50 / 00 9477 5 ) 4 00 50 / 490 9485 0 800 50 / 90 949 80 000 500 / 890 5078 00 00 500 / 090 500 0 400 500 / 90 E 95 Additional scissor stay (from S..W. 400mm) 040 ) ) 0 Stay corner drive P 949 Multipart center lock, horizontal and vertical Sash rebate Sash rebate Size Material width height 0 00 0 800 00 KUE 977 80 400 00 KU E 9789 00 KU E 977 ebate corner hinge E5 with integrated 50890 sash hardware groove packers 5090 Corner pivot rest E5 959 950 Corner pivot rest E5 with supporting pins 509 (not depicted) for sash weights up to 50kg 5099 4 ifting mishandling device, sash (S..H. > mm) 5 ifting mishandling device, frame (S..H. > mm) Horizontal Tilt&Turn striker 7 Striker 8 Bullet catch, frame component 97785 9779 08 090 877 98885 Cover Caps available for hinges! efer to page 7 for finish options and part s. 7 Sash stay arm E5 Sash rebate Size Material width 90 40 50* 5097 50945 4 00 50 5095 509 0 800 50 50970 50988 80 400 500 5099 5008 8 Sash stay bearing E5 05900 Sash stay bearing E5 with supporting pins 505 (not depicted) for sash weights from up to 50kg 9 Sash stay bearing pin 988 ) Use an additional scissor stay from S..W. 400mm ) Not possible in combination with lifting mishandling device. ) With special corner drive 4 4) With corner drive 5) On S..W. < 0mm assembly clip must be removed * Maximum tilt range 80mm 4
Basic Security French - Turn Only / Tilt&Turn Without Astragal /8-9 Hardware Overview & Parts ist 7 9 5 7 9 4 8 7 0 8 5 4 See HOPPE Window Handles at www.us.hoppe.com 9 0 NOTE: Mushroom cam (P) required on this corner. NOTE: Mushroom cam (P) required on this corner. 0 9 9 4 On SH < 500 mm, the tilt range must be limited to 80 mm! Application range Sash rebate width...90-00mm ) Sash rebate height...4-400mm Sash weight...max. 0kg (Up to 50kg with upgraded components at positions and ) Centered/variable handle height T&T espagnolette, 5mm backset Sash rebate Handle height Espagnolette Material height length 0 450 ) 55 0 40 905 45 0 4 ) 5 0 400 800 400 580 E 80 00 40 00 980 E 0 00 0 800 80 E 0 000 80 000 780 E 00 400 00 00 80 4 E 9054 90559 9057 90575 9058 9059 Corner drive (not depicted) E 0087 Corner drive P 944 Special corner drive E (S..H. < 0mm) 944 (S..H. < 0mm) Special corner drive P 945 ) ) 4 Sash stay guide Sash rebate Description / length Material width 90 40 50 / 00 9477 5 ) 4 00 50 / 490 9485 0 800 50 / 90 949 80 000 500 / 890 5078 00 00 500 / 090 500 0 400 500 / 90 E 95 5 Sash stay arm E5 Sash rebate Size Material width 90 40 ) 50 5097 50945 4 00 50 5095 509 0 800 50 50970 50988 80 400 500 5099 5008 5
Basic Security French - Turn Only / Tilt&Turn Without Astragal /8-9 Parts ist (Continued...) Application range Sash rebate width...90-00mm ) Sash rebate height...4-400mm Sash weight... max. 0kg (Up to 50kg with upgraded components at positions and ) Sash stay bearing E5 05900 Sash stay bearing E5 with supporting pins 505 (not depicted) for sash weights up to 50kg 7 Sash stay bearing pin 988 8 Stay corner drive P 949 9 Multipart center lock, horizontal and vertical Sash rebate Sash rebate Size Material width height 0 00 0 800 00 KU E 977 80 400 00 CON E 9789 00 KU E 977 0 ebate corner hinge E5 with integrated 50890 sash hardware groove packers 5090 9 Additional scissor stay (S..W. > 99mm) 040 0 Concealed center closer, sash component 0 Concealed center closer, frame component 7797 Striker 877 Horizontal Tilt&Turn striker 08 090 4 Security striker 79 747 Cover Caps available for hinges! efer to page 7 for finish options and part s. Corner pivot rest E5 959 950 Corner pivot rest E5 with supporting pins 509 (not depicted) for sash weights up to 50kg 5099 ifting mishandling device, sash (S..H. > mm) ifting mishandling device, frame (S..H. > mm) 97785 9779 4 Bullet catch cam (S..H. > 0mm) 098 5 Bullet catch, frame component (S..H. > 0mm) 98885 ebate hinge, sash component 77 7 ebate hinge arm E5 958 959 8 Centered/variable lever height lever operated espagnolette Sash rebate ever position Espagnolette Material height length 70 50 ) 5 50 400 978 ) 5 0 4 ) 5 50 400 978 ) 50 9 48 80 5 8004) 9 48 80 80 00 48 8 980 0 00 448 58 80 0 000 80 890 780 ) 7 ) 978 978 0 97840 97858 00 400 880 090 80 978 ) Use an additional scissor stay from S..W. 400mm 9 ) Not possible in combination with lifting mishandling device. ) With special corner drive 4) With corner drive 5) On S..W. < 0mm assembly clip must be removed ) Maximum tilt range 80mm 7) When using the lever operated espagnolette on the right hand side (viewed from inside), turn the eccentric cam 80 degrees We reserve the right to changes w ithout prior notice.
Tilt&Turn for High Wind oads /8-9 Hardware Overview 5 7 5 5 4 8 5 5 9 5 See HOPPE Window Handles at www.us.hoppe.com 9 5 5 NOTE: Mushroom cam required on this corner. 0 9 4 5 On S..H. < 500mm the tilt-range must be limited to 80mm! 7
Tilt&Turn for High Wind oads /8-9 Hardware Parts ist Application range Sash rebate width...490-400mm Sash rebate height...00-400mm Sash weight... max. 0kg (Up to 50kg with upgraded components at positions and ) Security centered/variable handle height T&T espagnolette, 5mm backset Sash rebate Handle height Espagnolette Material height length 800 580-400 V 909 80 00 980 40-00 V 9097 0 00 80 0-800 V 90989 0 000 780 80-000 V 90997 00 400 80 00-00 4 V 9009 Bullet catch cam (S..H. > 0mm) 098 Corner drive V 0775 4 Security sash stay guide Sash rebate Description/Size Material width 490 00 50 / 490 9485 0 800 50 / 90 949 80 000 500 / 890 V 7800 00 00 500 / 090 V 788 0 400 500 / 90 V 78 5 Sash stay arm E5 Sash rebate Size Material width 490 00 50 5095 509 0 800 50 50970 50988 80 400 500 5099 5008 Sash stay bearing E5 05900 Sash stay bearing E5 with supporting pins 505 (not depicted) for sash weights up to 50kg 9 Multipart center lock, horizontal and vertical Sash rebate Sash rebate Size Material width height 490 90 00 800 00 V 984 9 890 80 000 400 V 985 89 090 00 00 00 V 989 09 90 0 400 00 KU V 0588 00 V 984 9 400 40 00 00 KU V 0588 400 V 985 0 800 00 KU V 0588 00 V 989 80 000 00 KU V 0588 00 KU V 0588 00 V 984 00 00 00 KU V 0588 00 KU V 400 V 0588 985 0 400 00 KU V 0588 00 KU V 0588 00 V 989 0 ebate corner hinge E5 with integrated sash hardware groove packers 50890 5090 Corner pivot rest E5 959 950 Corner pivot rest E5 with supporting pins 509 (not depicted) for sash weights up to 50kg 5099 ifting mishandling device, sash (S..H. > mm) 97785 ifting mishandling device, frame (S..H. > mm) 4 Steel horizontal Tilt&Turn striker 9779 457 7 Sash stay bearing pin 988 5 Steel security striker 454 455 8 Stay corner drive V 0804 Bullet catch, frame component (S..H. > 0mm) 98885 Cover Caps available for hinges! efer to page 7 for finish options and part s. 8
Basic Security Turn-Only /8-9 Hardware Overview 7 9 8 8 8 5 4 8 9 5 See HOPPE Window Handles at www.us.hoppe.com 4 NOTE: Mushroom cam required on this corner. 0 5 7 8 We reserve the right to changes w ithout prior notice. 9
Basic Security Turn-Only /8-9 Hardware Parts ist Application range Sash rebate width...90-00mm Sash rebate height...80-400mm Sash weight...max. 0kg (Up to 50kg with upgraded components at positions 8 and ) Centered/variable handle height T&T espagnolette, 5mm backset Sash rebate Handle height Espagnolette Material height length 0 450 ) 55 5 40 905 ) 45 0 ) 5 0 400 9054 ) 800 400 580 E 90559 80 00 40 00 980 E 9057 0 00 0 800 80 E 90575 0 000 80 000 780 E 9058 00 400 00 00 80 4 E 9059 Bullet catch cam (S..H. > 0mm) 098 Corner drive (not depicted) E 0087 Corner drive P 944 4 Special corner drive (not depicted) E 944 (S..H. < 0mm) Special corner drive P 945 (S..H. < 0mm) 5 Multipart center lock, horizontal Sash rebate Size Material width 0 00 00 E 977 ifting mishandling device, sash (S..H. > mm) Travel-restrictor (90 ) 4 ifting mishandling device, frame (S..H. > mm) 5 Concealed center closer, sash component Concealed center closer, frame component 7 Security striker 8 Striker 9 Bullet catch, frame component (S..H. > 0mm) 97785 4709 9779 7797 0 79 747 877 98885 Cover Caps available for hinges! efer to page 7 for finish options and part s. Sash component for rebate hinge 77 7 ebate hinge arm E5 985 507 8 Sash stay bearing E5 05900 Sash stay bearing E5 with supporting pins 505 (not depicted) for sash weights up to 50kg 9 Sash stay bearing pin 988 0 ebate corner hinge E5 with integrated 50890 sash hardware groove packers 5090 Corner pivot rest E5 959 950 Corner pivot rest E5 with supporting pins 509 (not depicted) for sash weights up to 50kg 5099 ) Not possible in combination with lifting mishandling device. ) With special corner drive 4 ) With corner drive 0
Basic Security Tilt-Only (Hopper) /8-9 Hardware Overview 7 8 5 8 8 * See HOPPE Window Handles at www.us.hoppe.com 5 5 8 8 PEASE NOTE: Application of the tilt stay vertically is only possible without center locks! 4 4a 4a 4 * If the tilt stay is not mounted on top of the espagnolette gear box, the enclosed packer is to be installed under the tilt stay faceplate. We reserve the right to changes w ithout prior notice.
Basic Security Tilt-Only (Hopper) /8-9 Hardware Parts ist Application range (refer to application diagram) Sash rebate width...0-400mm Sash rebate height...90-00mm Sash weight...max. 80kg Centered/variable handle height T&T espagnolette, 5mm backset Sash rebate Size Material width 0 450 40 905 ) 45 0 400 9054 800 580 E 90559 80 00 980 E 9057 0 00 80 E 90575 0 000 780 E 9058 00 400 80 4 E 9059 Corner drive (not depicted) E 0087 Corner drive P 944 4a Sash stay bearing pin 988 5 Tilt stay* 040 Turn-Only/Tilt-Only rebate hinge E5 with integrated sash hardware groove packers Material with alignment 97 without alignment ) 980 7 Travel-restrictor (90 ) 4709 Multipart center lock, vertical Sash rebate Size Material height 80 00 400 E 97 4 Sash stay bearing E5 05900 8 Striker 877 Cover Caps available for hinges! efer to page 7 for finish options and part s. ) With special corner drive. ) When using two or more Turn-Only/Tilt-Only rebate hinges, one hinge without alignment must be used.
Basic Security Pitched Tilt&Turn /8-9 Hardware Overview 9 9 7 0 9 4 9 5 0 5 See HOPPE Window Handles at www.us.hoppe.com 7 NOTE: Mushroom cam required on this corner. 8 9 8 9 Dated: November 004. Page / AB 50- GB 4
Basic Security Pitched Tilt&Turn /8-9 Hardware Parts ist Application range Sash rebate width... 40 00mm Sash rebate height... 5 400mm Sash weight... max. 80kg Sash stay guide Sash rebate width Description / length Material eg length E 90 40 50 / 00 9477 4 00 50 / 490 9485 0 800 50 / 90 949 80 000 500 / 890 5078 00 00 500 / 090 500 0 400 500 / 90 E 95 Pitched sash stay arm E5 Sash rebate width Size Material eg length 90 40 50 98800 9888 4 00 50 988 9884 0 800 50 9884 9885 80 400 500 9889 98877 End piece Pitched stay guide 45 4 Centered/variable handle height T&T espagnolette, 5mm backset Sash rebate Handle height Espagnolette Material E height length (to start of pitch) 0 450 55 5 40 45 0 5 0 400 800 400 580 E 80 00 40 00 980 E 0 00 0 800 80 E 0 000 80 000 780 E 00 400 00 00 80 4 E 905 9054 90559 9057 90575 9058 9059 5 Center lock, vertical Sash rebate Size Material height 800 00 400 97 0 400 00 E 977 40 800 00 KU E 9789 80 000 400 E 97 00 KU E 9789 00 E 977 00 400 00 KU E 9789 00 KU E 9789 400 E 97 ) ) Arched component Sash rebate Size Material width 40 50 40 049 5 70 0 E 057 7 90 80 E 5 9 0 00 E 05 0 0 E 7 Espagnolette extension Sash rebate width Description / size Material eg length 40 00 00 E 50 0 800 400 E 9708 8 T&T corner drive P 944 9 Arched corner drive 08 0 Pitched corner drive E 089 Sash stay bearing E5 05900 Sash stay bearing pin 988 ebate corner hinge E5 height adjustable 4 Corner pivot rest E5 laterally adjustable 9574 958 959 950 5 Bullet catch cam (S..H. > 0mm) 098 ifting mishandling device, sash (S..H. > mm) 97785 7 ifting mishandling device, frame (S..H. > mm) 8 Horizontal Tilt&Turn striker 9 Striker 0 Bullet catch, frame component (S..H. > 0mm) 9779 08 090 877 98885 Cover Caps available for hinges! efer to page 7 for finish options and part s. ) Not possible in combination with lifting mishandling device. 4
Basic Security Arched Tilt&Turn /8-9 Hardware Overview 9 NOT Connectable 5 Connectable 9 9 Notch Cut off the additional scissor stay frame component at the notch 4 9 5 0 9 See HOPPE Window Handles at www.us.hoppe.com 7 7 Please note: The run-up block is to be adjusted in such a manner, that when the sash is pushed from the tilted into the locked position, the arched stay arm enters without brushing up against anything. 9 NOTE: Mushroom cam required on this corner. 8 0 8 9 4 5
Basic Security Arched Tilt&Turn /8-9 Hardware Parts ist Application range Sash rebate width...400-00mm Sash rebate height...500. - 900mm Sash weight...max.. 80kg Basic set System /8-9 Consisting of: arched stay arm E5 arched stay arm retainer run-up block for arched window 9554 Centered/variable handle height T&T espagnolette, 5mm backset Sash rebate height Handle height Espagnolette length Material (to start of arch) 0 450 55 5 40 905 45 0 5 0 400 9054 800 400 580 E 90559 80 00 40 00 980 E 9057 0 00 0 800 80 E 90575 0 000 80 000 780 E 9058 00 400 00 00 80 4 E 9059 Arched espagnolette connector Sash rebate Sash rebate Material width height 400 00 400 00 E 09 4 Additional scissor stay for arched window Sash rebate Sash rebate Material width height from 900 from 980 048 5 Arched center lock Sash rebate Size Material width 0 00 750 E E 077 Arched center lock - CONNECTABE Sash rebate Size Material width 0 00 590 E E 085 7 Arched center lock, vertical Sash rebate Size Material height 500 700 40 049 70 900 0 E 057 90 00 80 E 5 0 00 00 E 05 0 500 0 E 50 700 40 E 07 70 900 0 E 08 E ) ) 8 Arched center lock, horizontal Sash rebate Size Material width 400 500 80 09 without tilt travel 50 700 440 00 70 900 40 E 04 90 00 840 E 0 0 00 040 E 0 ) 9 T&T corner drive P 944 0 Arched corner drive 08 Sash stay bearing E5 adjustable 95 Sash stay bearing pin 988 ebate corner hinge E5 height adjustable 4 Corner pivot rest E5 laterally adjustable 9574 958 959 950 5 Bullet catch cam (S..H. > 0mm) 098 ifting mishandling device, sash (S..H. > mm) 97785 7 ifting mishandling device, frame (S..H. > mm) 8 Horizontal Tilt&Turn striker 9 Striker 0 Bullet catch, frame component (S..H. > 0mm) 9779 08 090 877 98885 Cover Caps available for hinges! efer to page 7 for finish options and part s. Not possible in combination with lifting mishandling device.
E5 Cover Caps Cover Cap Color ecommended HOPPE Handle Finish Pairing Cover Cap Stay - Arm Hinge E5 Cover Cap Stay Bearing E5 Cover Cap Stay Bearing E5 Adjustable Material No. Material No. Material No. Silver F Silver (aluminum handle styles only) F4- Brushed Chrome esista 580 575 48 Champagne F4- Satin Nickel esista 588 574 704 Matte Titanium F44- Antique Nickel esista 58 577 7 Polished Brass F77- esista Brass 5844 578 449 Grey - Brown F79 Oil ubbed Brass 750 78 7 Black - Brown F8709 ustic Umber F974 Matte Black 585 5799 490 Medium Bronze F7 Antique Brass 94 97 4 White F900 White 58 580 40 Cover Cap Color ecommended HOPPE Handle Finish Pairing Cover Cap ebate Corner Hinge E5 Cover Cap Pivot est E5 Material No. Material No. Silver F Silver (aluminum handle styles only) F4- Brushed Chrome esista 55 5 5 54 Champagne F4- Satin Nickel esista 5 540 550 58 Matte Titanium F44- Antique Nickel esista 558 5 57 584 Polished Brass F77- esista Brass 574 58 59 5705 Grey - Brown F79 Oil ubbed Brass 794 795 799 7977 Black - Brown F8709 ustic Umber F974 Matte Black 59 50 57 57 Medium Bronze F7 Antique Brass 90 95 99 977 White F900 White 50 58 570 5748 7
Sash Cross Section Window Handle Drilling / Installation. Sash cross section, dimensions for hardware 9.4 Hardware groove. Hardware axis.. 9 8. Window handle drilling Gear case sprocket and lugs drill holes for the window handle. 8 5 Backset Ø 5 4 with a mm overlap-height Handle height dimension G Ø0mm, mm deep Ø5 5 Backset Cad drawings for 5mm and deeper backsets available upon request.. Mounting the window handle Fix the window handle with Ø5mm countersunk screws DIN95 (M5 X...) in the espagnolette gear casing. Fixed threaded bevels Hardware groove Espagnolette gear casing 8
Frame Drilling Dimensions ebate systems Euro-rebate system Ø7mm drilling jig Material 5087 (778) 8/0 Ø40mm guide ring, Ø4mm milling cutter Hardware axis 8 Drilling plate stop on an assembled frame Drilling dimensions: Sash stay bearing / corner pivot rest on an assembled frame Ømm screw holes Sash stay bearing / corner pivot rest on an assembled frame Supporting-pin version Sash weight over 00kg screw in additional screws into the available screw holes (4) Ø4 (4) Ø4 Additional screw holes 44.5.5 Ø4.5 A A 44.5 B Drilled holes Ø7.0mm 7.5mm deep (8) 44 B 44 Ø4 (4) (4) A A B B 8/0 5 8/0 5 8 Ø 7 7.5 The dimensions in brackets apply to the /0-9 system! 9
Sash Cropper / Installation of Hardware Components. Cropping with the pneumatic cropping tool (punched hole). Strong interlocking hardware connection. Installation procedure (suggestion) 4 Corner drive T&T espagnolette Stay corner drive P 4 Sash stay guide 5 Vertical and horizontal, center lock Corner hinge E5 5 5 0
Sash Installation: Sash Stay Arm Tilt estrictor Anti-Slam Device Standard tilt range (40mm) educed tilt range (80mm) 80 Slider Hitching pin Slider Hitching pin Tilt range 40mm Tilt range 80mm * Slider's final position = Anti-slam device * Slider's final position = Anti-slam device * The slider's final position (anti-slam device) is reached automatically by means of tilting the sash.
Frame Installation: Basic Security Tilt&Turn Hardware Components Striker locations (mm) T&T espagnolette with centered/variable handle height 7 50 Handle/ Center E.M.D. B.C..M.D. B C D A Horizontal Tilt&Turn striker Centered/variable handle-height T&T espagnolette, BS5 Sash rebate height A B C D E.M.D. B.C. 450 0 800 5 7 80 00 5 7 0 00 5 40 7 0 000 58 09 00 400 58 758 740 09 4 8.5
Frame Installation: Basic Security Turn Only Hardware Components Striker locations (mm) T&T espagnolette with centered/variable handle height 7 50 Handle/ Center.M.D..M.D. E B C D B.C. A Centered/variable handle height T&T espagnolette, BS5 Sash rebate height A B C D E.M.D. B.C. 450 0 800 5 7 80 00 5 7 0 00 5 40 7 0 000 58 09 00 400 58 758 740 09 58
Installation Advice Hinging the sash Insert the sash stay bearing pin with the sash closed & the handle in the tilted position. Sash stay bearing pin Installation Closed position Unhinging the sash emove the sash stay bearing pin using the pin extractor handle while the sash is closed & the handle is in the tilted position. Pull out thepin in this position with the pin extractor handle mm Pin extractor handle Material 07. Slide in the sash stay. Push in the sash stay bearing bearing pin manually. pin with the pin extractor handle (for sash stay bearing pin). Frame clearances (incl. cover cap) etro adjustment (only if necessary) ± Adjustment tool: Allen-key screwdriver.5/4mm Material 708 + Corner pivot rest fixing: Screw protrusion as illustrated below Version with cover cap Painted version without cover cap 5 +.5.0 ±0.5 ± The indicated adjusting dimensions change upon use of cover caps (on sash stay bearing / corner pivot rest). 4
ocking Cam Adjustment Instructions ocking cam E E Adjustment Gasket compression range in degrees adjustment in mm Original position ocking cam P E Adjustment Gasket compression range in degrees adjustment in mm Original position 90 90 + /- 0.8 90 90 + /- 0.8 ocking cam V V Adjustment Gasket compression Height range in degrees adjustment adjustment in mm in mm 0 = Original position Original position + /- 0.8 + /- 0. 90 90 0.8mm max. adjustment 80 80 + /- 0.4 + 0.8mm max. adjustment 70 70 + /- 0.8 + /- 0. + /- 0.8 0 0 5
Maintenance ecommendations The windows you have produced have high quality oto hardware. This means: ease of operation, perfect function and high durability. The conditions for the function and smooth operation of the hardware are the compliance with our regulations concerning sash size and sash weight, as well as our product liability guidelines. Function and status of the hardware are to be checked in accordance with the following criteria: Smooth operation Hardware fixing Hardware wear and tear Hardware damage Hardware fixing The window s function and its security efficiency depend on the secure fixing of the hardware. Stability and location of the individual screws are to be tested. Should it be revealed that, for example, screws have loosened or that screw heads have broken off, tighten or replace these immediately. Hardware wear and tear All function-relevant hardware components are to be lubricated, respectively oiled according to our information, in order to avoid wear and tear. Smooth operation The hardware s smooth operation can be checked by means of moving the window handle. The locking and unlocking torque of the window handle is specified in accordance with DIN 8055 (German Industrial Norm) with a maximum value of 0 Newton meters. The inspection can be carried out with a torque wrench. The smooth operation can be improved by means of lubricating or by adjusting the hardware. oto Tilt&Turn hardware is designed with D/D adjusting possibilities. Incorrect and/or inappropriate retro-adjustments to the hardware can result in the windows not fulfilling their function anymore. Hardware damage Damaged hardware components are to be replaced especially if it concerns supporting hardware components. No legal claims can be derived from these recommendations; the application is to be conveyed for each individual case. oto Frank AG recommends window fabricators to make maintenance agreements with their end users.
Maintenance Instructions for Operation-elevant Components for Timber Windows and Balcony Doors Maintenance By means of regular greasing and oiling * (at least once a year) all operation-relevant components in the sash and frame, you maintain the smooth operation of your oto hardware and you protect against premature wear and tear. Security strikers made of steel require continuous greasing in order to avoid unnecessary abrasion. In addition, the individual screws are to be checked. Possible loose screws or broken off screw heads are to be replaced immediately by a trained professional. * Please use acid free and non-resinous grease and/or oil from a specialized dealer. 7
Operating and Safety Instructions for Timber Windows and Balcony Doors Operation Avoid mishandling In order to preserve the long operativeness of your window and to guarantee security, it is imperative to observe the directives listed below. The window sash may not be stressed with additional weight. Do not allow the sash to hit or press up against the window reveal. Do not place any objects between the sash and frame. Where small children or mentally handicapped persons have access to the window, the sash is to be safeguarded against turning, for example with a child-safety lock (inhibits turn-modes, permits tiltmodes) or key-lockable handle. Do not leave sashes open in the turn-modes during strong winds. Caution! A slamming sash can lead to injuries. While closing, do not grasp between the sash and frame. 8