Reversible nd Proportionl Electric s The MP s re used for two-position, floting, nd proportionl control of dmpers, vlves, nd progrm switches in heting, ventiltion, nd ir conditioning pplictions or similr pplictions. MP-xx eries, MP-xx eries, MP-xxx eries, nd MPxxx eries Fetures: Proportionl ctutors with built-in feedbck potentiometers. Spring return nd non-spring return models vilble. Vc, 10 Vc, nd 0 Vc models re vilble. Die cst housings with four 1/ in. conduit openings. Oil-immersed motor nd ger trin. Typicl Spring Return Typicl -6XX Suffix (CP-801-XXX Instlled, -XXX or CP-90-91X Instlled) Typicl Non-Spring Return Typicl -691 or -69 Suffix (-XXX or CP-90-91X Instlled) Model Chrt MP-xx. Model No. Appliction Solid Stte CP-801-xxx CP-90 Power Requirements Volts Hz Amps 60 lb.-in. (N-m) Timing Seconds (No Lod) Output Shft Degrees of Rottion Spring Return Aux. Switch MP-61 Avilble MP-61-600 c CP-801-0 Proportionl 180 (Adj. b ) CW MP-61-691 d MP-6 Sequencing SPST.5 50 MP-1 Avilble (5.6) 90 b c d MP-1-600 c MP-1-691 d Proportionl CP-801-0 180 (non Adj.) MP- Sequencing SPST MP-9 Five position None MP-81 10 Proportionl Avilble MP-8 10 to 100. 0 (Adj.) 180 (.9) (Adj. b No MP-8 Sequencing ) SPST 10 MP-89 Five position Avilble None MP5-81 Proportionl 50.5 156 Built-in Trnsformer Units with - suffix, e.g. MP-xxxx-xxx--x, include built-in trnsformer (used for Microtherm or with AE-50) with secondry lods wired externlly to terminls seven nd eight of the ctutor. Red ( Vc) to terminl eight nd Blue (1 Vc) to terminl seven. When these ctutors re used with controllers other thn Microtherm or AE-50, disconnect the Red nd Blue leds nd tpe off. Note: Models prior to - suffix hd trnsformer wired directly to potentiometer. To disconnect the trnsformer, remove the bck plte of the ctutor, disconnect, nd tpe the trnsformer leds. Rottion djustble 5 to 0. Cution: On ctutors with proportionl input signls chnging the rottion will ffect the control, since the internl feedbck potentiometer s trvel is fixed. Integrl solid stte drive CP-801 ccepts 6-9 Vdc voltge with 0 Vdc power supply included. Integrl solid stte drive ccepts 6-9 Vdc voltge. CCW 1
MP-xx Model No. Appliction Solid Stte CP-90 Power Requirements Volts Hz Amps 10 60 lb.-in. (N-m) Timing Seconds (No Lod) MP-1 5 5 to 50 MP- (Adj.) 60 (6.8) MP- 1 1 to 10 MP- (Adj.) Proportionl Avilble 0.65 MP-51 80 80 to 800 MP-5 0 (Adj.) MP-5 (.9) 0 MP-5 MP-61-600 refer to footnote c CP-801-10 MR-61-691 MP-65 Proportionl Avilble MP-0 MP-1-600 MP-1-691 Five position refer to footnote c CP-801-10 0 to 00 (Adj.) 50 (5.6) 90 Output Shft Degrees of Rottion 180 (Adj. b ) 90 (Adj. b ) 180 (Adj. b ) 90 (Adj. b ) Spring Return No 180 (Adj. b ) CW 180 (non-adj.) CCW Aux. Switch MP-5 Proportionl Avilble 0.5 MP-80 Five position None MP-81 Proportionl Avilble MP-81-600 MP-81-691 c MP-8 refer to footnote c CP-801-10 0 (.9) MP-85 10 MP-86 Proportionl Avilble MP-95 0.95 MP5-8 50 0.5 50 (50.9) 0 (.9) 10 180 (Adj. b ) 65 90 (Adj. b ) 10 to 100 (Adj.) 10 180 (Adj. b ) No None 8 90 (Adj. b ) No Built-in Trnsformer b c Units with - suffix, e.g. MP-xxxx-xxx--x, include built-in trnsformer (used for Microtherm or with AE-50) with secondry lods wired externlly to terminls seven nd eight of the ctutor. Red ( Vc) to terminl eight nd Blue (1 Vc) to terminl seven. When these ctutors re used with controllers other thn Microtherm or AE-50, disconnect the Red nd Blue leds nd tpe off. Note: Models prior to - suffix hd trnsformer wired directly to potentiometer. To disconnect the trnsformer, remove the bck plte of the ctutor, disconnect, nd tpe the trnsformer leds. Rottion djustble 5 to 0. Cution: On ctutors with proportionl input signls chnging the rottion will ffect the control, since the internl feedbck potentiometer s trvel is fixed. 6 to 9V proportionl. 18
MP-xxx. Model No. Appliction Solid Stte CP-90 Power Requirements Volts Hz Amps lb.-in. (N-m) Timing Seconds (No Lod) Output Shft Degrees of Rottion Spring Return Aux. Switch Built-in Trnsformer MP-11-500 MP-10-500 MP-150-500 Proportionl Avilble. 60 10 0.5 50 (5.6) MP-151-500 0 0. 0 5 180 (non- Adj.) 90 (non- Adj.) 180 (non- Adj.) No Units with - suffix, e.g. MP-xxxx-xxx--x, include built-in trnsformer (used for Microtherm or with AE-50) with secondry lods wired externlly to terminls seven nd eight of the ctutor. Red ( Vc) to terminl eight nd Blue (1 Vc) to terminl seven. When these ctutors re used with controllers other thn Microtherm or AE-50, disconnect the Red nd Blue leds nd tpe off. Note: Models prior to - suffix hd trnsformer wired directly to potentiometer. To disconnect the trnsformer, remove the bck plte of the ctutor, disconnect, nd tpe the trnsformer leds. MP-xxx. Model No. Appliction Solid Stte CP-90 MP5-651 Proportionl Avilble Power Requirements Volts Hz Amps 50 lb.-in. (N-m) Output Shft Timing Seconds (No Lod) Degrees of Rottion 108 180 (Adj. b ) Spring Return MP-01 Five position 60 50 (5.6) 90 180 (non- CCW MP5-51 0 50 0.5 108 Adj.) MP-851 Proportionl Avilble 60 0 10 180 (Adj. (.9) b ) No MP5-851 50 156 CW Aux. Switch None Built-in Trnsformer b Units with - suffix, e.g. MP-xxxx-xxx--x, include built-in trnsformer (used for Microtherm or with AE-50) with secondry lods wired externlly to terminls seven nd eight of the ctutor. Red ( Vc) to terminl eight nd Blue (1 Vc) to terminl seven. When these ctutors re used with controllers other thn Microtherm or AE-50, disconnect the Red nd Blue leds nd tpe off. Note: Models prior to - suffix hd trnsformer wired directly to potentiometer. To disconnect the trnsformer, remove the bck plte of the ctutor, disconnect, nd tpe the trnsformer leds. Rottion djustble 5 to 0. Cution: On ctutors with proportionl input signls chnging the rottion will ffect the control, since the internl feedbck potentiometer s trvel is fixed. Prt Numbers for Hzrdous Loctions Applictions. Hzrdous Loctions Hz MP6-xx 60 MP-xx, MP-xx 50 Listing UL Listed nd CSA Certified Clss 1, Groups C nd D, nd Clss, Groups E, F, nd G Hzrdous Loctions; Ref. EN-56-. 19
Specifictions Input Control signls Refer to the Model Chrts for input control signl cpbility versus specific ctutor models. Floting Requires one Single Pole Double Throw () switch with floting (center off) position rted t 0.9 mps t Vc or two Single Pole Single Throw (SPST) switches rted t 0.9 mps t Vc. : Requires snp cting switch rted t 0.9 mps t Vc. Two-position SPST: Cn be used with certin spring return ctutors. Switch must be rted to hndle ctutor power requirements. Proportionl electricl system with the following typicl controllers: PP-x, TP-1xx, TP-xx, TP-xx, TP-xx, TP-1xxx, nd TP-1xxxx. Microtherm Stndrd: Control of single ctutor. Sequencing: Control of two ctutors in sequence. Five-position: Used typiclly for djustble minimum position (five positions) of n economizer ctutor. Slidewire nd prlleling Requires AE-50 prlleling rely. AE-50 ccepts 100 to 1000 slidewires. Voltge Vdc (System 8000) Requires CP-801-xxx or -xxx of solid stte ctutor drives. Refer to the Model Chrts. Current madc Requires CP-90-xxx of solid stte ctutor drives. Refer to the Model Chrts. Connections MP-xx, xx, xxx, xxx Coded screw terminls. Models -600 Suffix Coded screw terminls except for input signl which re color coded pigtils. Power Requirements Refer to the Model Chrts to determine power requirements. Refer to the Model Chrts to determine the ctutor torque rting. Nominl dmper re sizing should be done in ccordnce with dmper mnufcturer s specifictions. Spring return Refer to the Model Chrts for models tht re spring return. Environment Ambient temperture limits Shipping nd storge: -0 to 160F (-0 to 1C). Operting: -0 to 16F (-0 to 58C). Humidity 5 to 95% RH, non-condensing. Loctions NEMA 1. NEMA for non-spring return ctutors with AM-6. Dimensions MP-xx, xx, xxx, xxx H x 5-/8 W x 6-5/16 D in. (18 x 16 x 160 mm) NSR. Models -600 Suffix H x 5-/8 W x 8-1/8 D in. (18 x 16 x 06 mm) SR plus ctutor drive housing. Agency Listings UL 8 File E99 Temperture Indicting nd Regulting Equipment. CUL Cndin Stndrd #LR 8. Europen Community Generl Instructions EMC Directive 89/6/EEC nd 9/1 EEC. Low voltge Directive /EEC. Units with "-xxx-x-" suffix identify models tht re in complince with CE. Exmple: MP-xxxx-xxx-x-. Refer to F-159. 10
Accessories Model No. Description Dmper linkge ccessories AM-111 Crnk rm for 5/16 in. (.9 mm) dimeter dmper shft. AM-11 Crnk rm for /8 in. (9.5 mm) dimeter dmper shft. AM-11 Crnk rm for 1/ in. (1. mm) dimeter dmper shft. AM-115 Crnk rm for /16 in. (11.1 mm) dimeter dmper shft. AM-116 Splined crnk rm for ctutor. AM-1 Linkge connector, stright type. AM-1 Dmper clip. AM-15 5/16 x 0 in. (.9 mm x 0.5 m) dmper rod. AM-15-08 5/16 x 8 in. (.9 mm x 1. m) dmper rod. AM-1 Bll joint connector. AM-161 Dmper linkge kit. AM-161-1 Dmper linkge kit. AM-01 90 degree mounting brcket. Miscellneous ctutor ccessories AM-1 Two step switch kit. AM- Potentiometer kit. AM-1 Four step switch kit. AM- Two step switch nd potentiometer kit. AM-6 NEMA gsket kit for non-spring return ctutors only. CP-801 Electronic drive, voltge input 1 to 0 Vdc. Electronic drive, voltge input 6 to 9 Vdc. CP-90 Electronic drive, voltge input to 0 madc. TOOL-01 Clibrtion kit for System 8000. TOOL-09 15 slidewire clibrtion kit. Vlve linkge for 50 lb.-in. minimum, 180 ctutor. AV-91 Vlve linkge for 1/ to in. VB-XXX nd 1/ to 1-1/ in. discontinued VB-9XXX. AV-9 Vlve linkge for 1-1/ nd in. discontinued VB-9XXX. AV-95 Vlve linkge for -1/ to in. VB-91 or VB-91. Vlve linkge for 10 lb.-in. minimum, 180 ctutor. AV-5 Vlve linkge for -1/ to 6 in VB-91 or VB-91, to 6 in. VB-9. AV-9 Vlve linkge for 1/ to in. VB-XXX nd 1/ to 1-1/ in. discontinued VB-9XXX. AV-9 Vlve linkge for 1-1/ nd in. discontinued VB-9XXX. AV-96 Vlve linkge for -1/ to in. VB-91 or VB-91. Typicl Applictions 1 Terminls 1,5, & 6 re used for built-in uxiliry switch. Rottes CW or Lowers Vlve Stem. Rottes CCW or Rises Vlve Stem. These terminl re mrked L1 & L on line voltge ctutors. 5 Remove green wire to unground ctutor. 6 Neutrl Off Switch my be used on mnul positioning pplictions. Switch control circuit is 0.5 mp t pprox. Vc on either low or line voltge ctutors. 8 Instll under cover of ctutor. CYZR-818 8 Arc Suppressor purchsed seprtely 6 Red Blue White Floting Control AC Supply 5 X Green MP-00 MP-00 MP-00-600 MP-000-500 MP-000 H G Figure 1 Typicl Reversible Floting Wiring. 11
Mx. Amp Rting 10V 0V Running 5.8.9 Locked Rotor.8 1. Non-inductive 1 6 1 6 Terminl Identifiction 5 CCW Cm Action Fctory Setting CW Figure Adjustble Auxiliry Switch. MP-00 MP-00 MP-000-500 MP-000 PP-0 1 1 Controller R B 6 Blue C 6 X Red 8 Green 5 H G 100 Ω 8 8 1 1-Feedbck. C-Common. R-Closes on pressure drop nd rottes ctutor CCW. B-Closes on pressure rise & rottes ctutor CW. 5 Terminls 1, 5, & 6 re used for builtin uxillry switch. 1-5NC, 1 -ENO 6 Built-in trnsformer leds on line voltge ctutor. Mke resistor nd jumper connections on V ctutors only. AC Supply 8 These terminls mrked L1 & L on line voltge ctutors. Line voltge ctutors require built-in trnsformer. Figure Typicl PP-xx Wiring. 1
AE-50 Prllel Rely Fctory Instlled to the Blck Brown Slidewire Input CCW CW MP-00 MP-00 MP-000-500 MP-000 1 Resistor & jumper present on V ctutors only. These terminls mrked L1 nd L on line voltge ctutors. Direction ctutor will drive. Cse ground screw. Brown/Yellow 680Ω Red/Blck 8 Blue/Blck Yellow/Blck X 680Ω 50Ω 1 H 1 Green G AC Supply Figure Typicl for Proportionl Slidewire. TP-8101 CP-810 1 CP-801-10 CP-801-0 CP-801-0 Solid Stte Fctory Instlled to the COM (Blue) OP (Yellow) +0 (Red) Red Yellow Blue Brown/Blck Brown/White Red/Blck Blue/Blck Yellow/Blck Brown X MP-00 MP-00 MP-00-600 MP-000-500 MP-000 8 L L1 1 Typicl controllers. rottes clockwise on increse in input signl. To rotte ctutor counterclockwise on n increse in input signl reverse Blue/Blck nd Red/Blck leds nd reverse Brown/Blck nd Brown/ White leds. Terminls 1, 5 & 6 re used for builtin uxilliry switch. 1-5NC, 1 -ENO Only Vc ctutors hve this ground. 5 Prt Number Vc Color CP-801-10 10 White CP-801-0 Blck/Blue CP-801-0 0 White/Blck 6 0 Vdc. 50 ma power supply in CP-801-xxx. 6 5 Blck 10 Vc AC Supply Figure 5 Typicl Proportionl Electronic Voltge. Wiring for MP-61-600, MP-1-600, MP-81-600. 1
or CP-90 Yellow Blue Violet/White Violet Brown/White Brown Brown/Blck Red/Blck Blue/Blck Yellow/Blck Green/Yellow 1 Cution: Before instlling the ctutor drive onto ctutors equipped with n internl trnsformer, the red nd blue leds must be disconnected from ctutor terminls nd 8, nd tped off. Filure to do so will result in dmge to the ctutor drive. As digrmmed, incresing input cuses CW ctutor rottion. All references to the direction of rottion re determined by fcing the ctutor output shft. The wires to terminls nd 8, nd nd, my be reversed for CCW rottion with n incresing input signl. MP-xxxx-xxx-x- models re equipped with n externl green jumper from terminl X to the terminl block mounting screw (ground). If the ppliction requires it, this jumper my be removed for isoltion purposes. 5 Vc models re equipped with jumper from terminl G to the cse ground screw. 6 The green/yellow wire must be instlled under the terminl block mounting screw. Shield must be grounded to the terminl block mounting screw. 6 Terminls 8 X 6 L1 (H) L (G) MP-xx, MP-xx, MP-1xx, or MP-9xx Wire Nuts 1 Input Common Purge Input (Override Input) Purge + (Override +) 100 Ohm Slidewire Limit Switches Shding Windings Green 9 Field Winding 5 To Controller Purge Override (Input Signl Override) 8 From Power Source 8 Purge override (input signl override) is vilble on CP-90 only. A dry contct closure from the override input (violet/white) led to the blue led of the ctutor drive forces the ctutor to drive to the end of trvel, independent of the input signl conditions. Connecting the violet/white nd violet leds together forces the ctutor to drive to the opposite (high input signl) end of trvel, independent of input signl conditions. 9 This wire should be removed on CP-90 when driving multiple ctutors. Figure 6 Typicl Proportionl Electronic - Current/Voltge Wiring for CP-90x to MP-xx, MP-xx, nd MP-1xxx s. 1