Analizzatore di Rete ADR Manuale d Uso etwork Analyser User s Manual
Index Safety warnings Page 4 echnical specifications Page 4 Instrument description Page 5 Keys Page 6 Parameter settings Page 6 Measurement page display Page 0 Measurement / calculation methods Page 6 Serial communications Page 7 ADR-View software Page 7 Reference standards Page 8 Dimensions and connection diagrams Page 9 - - ADR etwork analyser - User s guide
SAFEY WARIGS During the installation and operation of the instrument, proceed in accordance with the instructions below: ) he instrument should be installed by competent personnel ) Follow the installation diagrams carefully ) When connecting the instrument, always use A x/5 A 4) he appliance should be installed in a panel from which no access can be gained to the terminals after installation 5) he terminals of the voltage and current circuits may be connected with a maximum rated voltage to earth of 00 V eff 6) he panel should be wired in accordance with the E standards that apply 7) Do not power or connect the instrument if any part of it is damaged OE: VEMER mains analysers are designed to be used in locations with over-voltage category III and pollution level, in accordance with the E 600- standard he electrical system of the building in which the instrument is to be installed should have a switch or isolator fitted in the vicinity of the instrument in a place to which the operator has easy access. A protective device against over-currents should be fitted. ECHICA SPECIFICAIOS Power supply: 0 V AC (-5%/+0%) Frequency: 50/60 Hz Maximum power consumption: 4 VA Indications: customised, rear lit CD display Voltmeter inputs: max 550 V rms, 47 6 Hz Ammetric inputs: max 6 A rms, 47 6 Hz Scales: voltage scale with max reading 550 V rms current scales with maximum readings of A rms and 6 A rms Precision: -Voltage 0.5% of the end of scale value (for measurements between 0% and 00% of the end of scale) - Minimum signal measured 0 V - Current 0.5% of the end of scale value (for measurements between 0% and 00% of the end of scale) - Minimum signal measured 0 ma -Power % of the end of scale value -Frequency ±0. Hz (47 6 Hz) - Active energy class to standard E 605- - Reactive energy class to standard E 605- - 4 - ADR etwork analyser - User s guide
V selected: primary 9999 V, secondary 0 V A selected: primary 9999 A, secondary 5 A Serial output: insulated RS-485 with MODBUS RU protocol (max 9600 Baud) for the ADR-R, ADR-D, ADR-R E and ADR-D E models Operating temperature: 0 C +50 C (for the ADR-DE model: 0 C +40 C) Relative humidity: 0% 90% non-condensing Containers: - Rear panel version: material in class V-0 in line with the U 94 standard, standardised dimensions 7x7 mm in line with the DI 4700 standards - Modular version: material in class V-0 in line with the U 94 standard, 4 module DI container, colour RA-705 grey Analizzatore di Rete Code Model Description V56700 ADR-R Insulated network analyser with serial output, rear panel V560900 ADR-R Spot Insulated network analyser, rear panel V5600 ADR-D Insulated network analyser with serial output, modular V56500 ADR-D Spot Insulated network analyser, modular VE80400 ADR-R E Uninsulated network analyser with serial output, rear panel VE79600 ADR-R E Spot Uninsulated network analyser, rear panel version VE800 ADR-D E Uninsulated network analyser with serial output, modular VE07700 ADR-D E Spot Uninsulated network analyser, modular V56400 ADR-view.00 Software for network analysers + interface Display and messages ISRUME DESCRIPIO VOAGE CURRE FREQUECY APPARE REACIVE EERGY V GMk Wh Hz VARh cos A ADR 4 VOAGE CURRE FREQUECY APPARE REACIVE EERGY cos V GMk Wh Hz VARh A - umerical fields for the display of the values measured - ype of measurement taking place - Measurement unit - Phase symbols - 5 - ADR etwork analyser - User s guide
KEYS Scroll to the next page and set parameters Scroll to the previous page and set parameters Display of the system values For the ADR-D, ADR-R, ADR-D E and ADR-R E: Display of the peak value and selection of parameters during programming For the ADR-D spot, ADR-R spot, ADR-D E spot and ADR-R E spot : Parameter selection during programming PARAMEER SEIG Access to the programming menus takes place when the instrument is switched on by holding down the up ( ) and down ( ) keys at the same time. he following parameters can be programmed by the user in the order shown: Primary V (fixed secondary 0 V) Primary A (fixed secondary 5 A) Serial port configuration ( screen displays) (not available in the spot version) Zeroing of active energy meter Zeroing of reactive energy meter Rear lighting handling For a new parameter setting, the power to the instrument has to be cut off and restored by pressing the up ( ) and down ( ) keys at the same time. - 6 - ADR etwork analyser - User s guide
V setting VOAGE v VOAGE v Press the up ( ) or down ( ) keys to select the required value of the flashing figure o move to the next figure, press the key (or the ( ) key in the spot version) o confirm the value set and move to the next window, press A setting CURRE A CURRE A he same as the V setting procedure. ote: for the V and A primaries, any value from 000 to 9999 can be set. If the value 0000 is set, the instrument will force this to 000. he secondaries are set to 0 V and 5 A respectively. Serial port configuration (not in the spot version) Setting the serial port address: the same as the V setting procedure. - 7 - ADR etwork analyser - User s guide
k k k k Setting the serial port speed: press to select one of the 4 possible speeds (00, 400, 4800 or 9600 Baud). o confirm the value set and move to the next window, press. Setting the parity bit: press to select one of the options, OE, ODD or EVE, in order. o confirm the value set and move to the next window, press. Zeroing the active energy meter ACIVE EERGY ACIVE EERGY Press (or ( ) in the spot version) to select the option Yes or o. o confirm the value set and move to the next window, press. - 8 - ADR etwork analyser - User s guide
Zeroing the reactive energy meter REACIVE EERGY REACIVE EERGY Same procedure as the zeroing of the active energy meter. Rear lighting handling Press (or ( ) in the spot version) to select from the options O (rear lighting off), YES (on) or IME (on for approximately 60 seconds after a key is pressed). o confirm the value set and terminate the parameter setting procedure, press. ote: for ADR-D E model it is better not to select YES option (rear lighting always O). When is pressed, all the symbols in the display will come on for approximately seconds, followed by the display of the main page. ote: if the power is cut off during the programming procedure, the instrument will memorise all the settings in place at the instant when this occurs. - 9 - ADR etwork analyser - User s guide
DISPAYIG HE MEASUREME PAGE When the instrument is switched on (or after the programming procedure) the main page is displayed after approximately seconds when the display is fully operational. When up ( ) is pressed from the main page, the following are displayed: all the other measurement pages in sequence. When up ( ) is pressed from the last page, the system returns to the main page. If V is >999 or I is >999, the relevant measurement will flash to indicate that the unit is not complete (prefix K or M missing). ) Main page k W he system voltage, current and active power are displayed. V A ) Phase voltage page VOAGE V VOAGE V he phase voltages are displayed. If the three phase system has no neutral, the voltages refer to a fictitious star delta centre. he key is used to display the system voltage page. a) Peak phase voltage value page (not in the spot version) If is pressed repeatedly from one of the two phase voltage pages, the following are displayed in order: -the peak voltage values (phase of system), with the V measurement unit flashing - 0 - ADR etwork analyser - User s guide
VOAGE V VOAGE h VOAGE h - the instant when the peak occurred (time and date) - the number of hours lapsing between the start-up of the instrument and the occurrence of the peak (expressed in hours and tenths of an hour) o zero the peak values, simply press and at the same time he up ( ) key can be pressed at any time to move to the next page ) Concatenating voltage page VOAGE V he concatenating voltages between the phases are displayed 4) Phase current page CURRE A CURRE A he phase currents are displayed. he key is used to display the system current. - - ADR etwork analyser - User s guide
4a) Peak phase current value page (not in the spot version) CURRE A CURRE h CURRE h he same procedure as that for the display of the peak phase voltage values 5) Active phase power page W k W ACIVE ACIVE he active phase powers are displayed. he key is used to display the active system power. 5a) Peak active power value pages (not in the spot version) k W h h ACIVE ACIVE ACIVE he same procedure as that for the display of the peak phase voltage values - - ADR etwork analyser - User s guide
6) Apparent phase power page k VA k VA APPARE APPARE he apparent phase powers are displayed he key is used to display the apparent system power. 7) Reactive phase power page VAR k VAR REACIVE REACIVE he reactive phase powers are displayed. he key is used to display the reactive system power. 7a) Reactive power peak value pages (not in the spot version) VAR VAR h h REACIVE REACIVE REACIVE he same procedure as that for the display of the peak phase voltage values. - - ADR etwork analyser - User s guide
8) Phase power factor page cos cos he phase power factors are displayed he key is used to display the system power factor 9) Voltage-current phase shift page he voltage-current phase shifts are displayed in sexagesimal degrees (the letter C indicates a capacitative phase shift, and indicates an inductive phase shift) 0) otal active energy page k Wh Wh ACIVE EERGY ACIVE EERGY he total active energy is displayed he key is used to display the partial active energy of the single phases (these energy readings are zeroed each time the total active energy is increased) - 4 - ADR etwork analyser - User s guide
) otal reactive energy page k VARh k VARh REACIVE EERGY REACIVE EERGY he total reactive energy is displayed he key is used to display the partial reactive energy readings for the single phases (these energy readings are zeroed each time the total reactive energy is increased) ) Frequency page he V voltage frequency is displayed FREQUECY Hz ) ime and date page (not in the spot version) h h he time and date are displayed in dd-mm-yy format he key is used to move from the display of the time and date lapsed since the instrument was switched on (expressed in hours and tenths of an hour) he up ( ) key is used to return to the starting page - 5 - ADR etwork analyser - User s guide
a) Setting the time and date (not in the spot version) h h When is pressed from one of the time display pages, the time and date can be set Press the up ( ) or down ( ) keys to select the required value of the flashing number Press to move to the next number he key can be pressed at any time to return to the time display page, with the memorisation of the modifications entered ote: up to the entry of the first setting,the time and date will flash. he time and date will also flash in the peak value pages. MEASUREME / CACUAIO MEHOD he voltage and current measurements take place in (rue RMS) by means of sampling and analogue-digital conversion. o calculate the system values, the following formulas are used: System voltage V = V + V + V System current I = I + I + I Active system power P = P +P +P Reactive system power Q = Q +Q +Q (addition) Apparent system power A = P +Q System power factor PF = P A - 6 - ADR etwork analyser - User s guide
otal active energy E = E +E +E otal reactive energy Er = Er +Er +Er SERIA COMMUICAIO (not in the spot version) he instrument has an insulated RS-485 serial output he data communication system is based on the MODBUS protocol and is suitable for the connection of the following to a master device such as a PC or PC in a common RS-485 line: up to ADR (slaves) without the use of signal amplifiers, up to a maximum distance of 000 m up to 47 ADR (slaves) in groups of 0, separated by suitable signal amplifiers he communication takes place in half duplex and only the master (PC/PC) is able to start up the dialogues with the slaves, of a question/answer type (one slave only addressed), or with the message addressed to all the slaves (address 0) without obtaining any reply he features of the Modbus protocol implemented are: ype of coding: RU (Remote erminal Unit) ransmission speed (Baud Rate): 9600, 4800, 400, 00 bps (selected by the user) Byte format transmitted: start bit, 8 data bits, parity bit (can be selected): none, odd o even, stop bit For the Modbus functions and the use of the registers, ask the SA service for the relevant documentation. ADR-View software (optional) When the ADR-View software is installed (not suitable for the spot versions), it is possible to monitor all the values measured by means of tables and graphs, to set up a data file and obtain the trend of the signals over time. he software is available for Windows 98 or later and is based on a simple, user friendly interface. Minimum hardware requirements: IBM or compatible personal computer Pentium 00 microprocessor Mb of RAM (64Mb recommended) Minimum 0Mb space available on the hard disk VGA graphic card with 800x600 resolution (04x768 recommended) Colour monitor serial port dedicated to the RS-485 line connection - 7 - ADR etwork analyser - User s guide
REFERECE SADARDS Conformity to EC directives 006/95/EC (VD) 004/08/EC (EMC) is declared with reference to the following harmonised standards: Safety: E 600- Electromagnetic compatibility: E 6000-6- and E 6000-6-4 Metering requirements: E 605- and E 605- - 8 - ADR etwork analyser - User s guide
DIMESIOS VOAGE CURRE FREQUECY APPARE REACIVE EERGY V GMk Wh Hz VARh cos A 66 ADR-R 7 4 00 5 66-9 - ADR etwork analyser - User s guide
z z z COECIO DIAGRAMS ADR-R ADR-R E ~ 0 5 0-60 V~ H 6 5 4 AC Single phase 4 I + RS-485 0 9 8 7 + ADR-R ADR-R E AC I ~ 0 5 0-6 0 V~ H 6 5 4 I I + + + RS-485 + hree phase 4 0 9 8 7 ADR-R ADR-R E AC hree phase+ 4 I ~ 0 V~ 50-6 0 H 6 5 4 I I + + + RS-485 0 9 8 7 + S P Attention: the secondary circuits of the C can be earthed for the ADR-R model only P S I - 40 - ADR etwork analyser - User s guide
z z z COECIO DIAGRAMS ADR-R spot ADR-R E spot ~ 0 5 0-60 V~ H 6 5 4 AC Single phase 4 I 0 9 8 7 + ADR-R spot ADR-R E spot 5 0 ~ 0-6 0 V~ H 6 5 4 AC hree phase 4 I I I + + + 0 9 8 7 ADR-R spot ADR-R E spot AC hree phase+ 4 I ~ 0 V~ 50-6 0 H 6 5 4 I I + + + 0 9 8 7 S P Attention: the secondary circuits of the C can be earthed for the ADR-R spot model only P S I - 4 - ADR etwork analyser - User s guide
DIMESIOS 4 5 6 7 8 9 87 VOAGE CURRE FREQUECY APPARE REACIVE V EERGY GMk Wh Hz VARh cos A 45 ADR 0 4 5 6 7 8 70 60 65-4 - ADR etwork analyser - User s guide
z z z COECIO DIAGRAMS ADR-D ADR-D E AC Single phase 5 0 0-6 0 V~ ~ H RS-485 0 4 5 6 7 8 + I + 4 5 6 7 S/k 9 8 ADR-D ADR-D E AC hree phase 5 0 - RS-485 + 0 0 V~ ~ 6 0 H 4 5 6 7 8 I I I + + + 8 4 5 6 7 9 ADR-D ADR-D E AC hree phase+ 5 0 0-6 0 V~ ~ H RS-485 0 4 5 6 7 8 + I I I + + + 4 5 6 7 9 8 S P Attention: the secondary circuits of the C can be earthed for the ADR-D model only P S I - 4 - ADR etwork analyser - User s guide
z z z COECIO DIAGRAMS ADR-D spot ADR-D E spot AC Single phase 0 0 5 0-6 0 V~ ~ H 4 5 6 7 8 I + 4 5 6 7 9 8 ADR-D spot ADR-D E spot AC hree phase 5 0-0 0 V~ ~ 6 0 H 4 5 6 7 8 I I I + + + 4 6 8 5 7 9 ADR-D spot ADR-D E spot AC hree phase+ 5 0 0 0-6 0 V~ ~ H 4 5 6 7 8 I I I + + + 4 5 6 7 9 8 S P Attention: the secondary circuits of the C can be earthed for the ADR-D spot model only - 44 - ADR etwork analyser - User s guide P S I
VIS00498-00-070 Vemer S.p.A. I - 0 Feltre (B) Via Camp onc, 6 el +9 049 8068 Fax +9 049 8069 e-mail: info@vemer.it - web site: www.vemer.it