封底 封面 148.5 x 210(mm) www.ezset.com.tw PMR ELECTRONIC LOCK USER GUIDE
封面裡 Parts Introduction Do not use an electric screwdriver when installing the product! Installation Procedures 1. Draw horizontal lines on the door and door edge Measure for the lever center line on the door and door edge 36" (914mm) above the floor and then draw out the latch center line according to the paper template. 2. Set the central point for drilling Following the paper template, determine whether the door is right- or left-handed and then place the appropriate paper template to the door and door edge, aligning with the latch center line and the lever center line (as illustrated) and marking the centers of the holes. (In all illustrations a right-hand door is the example) Latch center line Lever center line 36" (914mm) Interior lock body Mortise lock case Exterior lock body 3. Door Edge Drilling Center line of the door edge Fixing plate Screw for screw post x6 Metal screw Proximity card Hex wrench 13mm Rotating plate screw Exterior spindle Interior spindle 1. Following the marks, drill 2 holes, 1" (25.4mm) in diameter and 4-17/32" (115mm) deep on the door edge and then, based on the positions of the 2 holes, chisel out a rectangular groove (the line segments on the paper template) 1" (25.4mm) in width, 6-3/8" (162mm) in height and 4-17/32" (115mm) deep for the installation of the lock case (Illustration 1). 2. Following the paper template, cut a groove 1-5/16" (33mm) in width, 8-1/32" (204mm) in height and 1/4" (6.5mm) deep on the door edge to provide a level door edge surface once the faceplate is installed (Illustration 2). 6-3/8"(162mm) Strike screw x6 Faceplate screw Screw Post Rotating Plate Cylinder Key Interior lock body screw Spring Battery cover Strike box Nameplate Faceplate Strike 3. Finally, following the marks on the paper template, drill two guiding holes (screw holes) 1/8" (3mm) in diameter and 19/32" (15mm) deep to complete the door edge drilling (Illustration 2) 4. Door face drilling Following the markings of the paper template and the size requirements, drill the holes for the lock cylinder, the thumb turn, and the lever and six other penetrating holes. Please be sure to drill from the inside out and the outside in respectively to prevent burrs and other damage to the door. ( Illustration 1) ( Illustration 2) ø1/8" (ø3mm) guiding hole of depth 19/32" (15mm) 1 2
5. Strike Installation 1. Swing the door almost closed up to the door jamb and draw the latch center line on the door jamb to match the latch center line on the door. 2. Place the strike paper template onto the door jamb, aligning it to the latch center line, and mark the centers of the holes on the door jamb as specified by the paper template. Following the markings, drill 2 holes, 1" (25.4mm) in diameter and 1-1/8" (29mm)deep, on the door jamb and then chisel out a rectangular groove (the line segments of the strike paper template) 1" (25.4mm) in width, 3-5/16" (84mm) in height and 1-1/8" (29mm) deep based on the positions of the 2 holes. 3. t the position specified by the paper template, cut a groove 1-5/16" (33mm) in width, 4-7/8" (124mm) in height and 5/32" (4mm) deep on the door jamb to provide a level surface on the door jamb once the strike is installed. 4. Finally, following the markings, drill 2 guiding holes, 1/8" (3mm) in diameter and 19/32" (15mm) deep, to fasten the strike with strike screws (for a metal door, metal screws can be used to fasten the strike). Caution : 1. Doors with a thickness greater or less than 55mm use strike plates of different specifications (as illustrated below). Please chisel out the groove for the strike plate as appropriate according to the strike specifications and by referring to the paper template markings. 2. The strike provided by the manufacturer must be used to prevent a malfunction of automatic locking as a result of the security latch's inability to depress. 3-5/16" (84mm) ø1/8" (ø3mm) guiding hole 19/32" (15mm) deep Standard strike for a door thinner than 55mm Standard strike Special strike Special strike for a door thicker than 55mm 6. Lock Case Installation 1. First, insert the upper and lower IC wires into the door's groove and then pull them out through the penetrating holes above and below the groove on the room side (do not cross the upper and lower cables). 2. Insert the lock case into the groove, gently pulling the wires at the same time without breaking them, and then position the reinforce plate as illustrated, fastening the latch tightly with lock case screws (for a metal door, metal screws can be used instead to fasten the latch). 7. Exterior Lock Body Installation Upper wire exit hole Lower wire exit hole The room side 1. Screw the 2 screw posts into the opposite screw holes on the exterior lock body according to the door handing : for a right-hand door, screw posts are assembled in the upper-left and lower-right corners, and for a left-hand door, screw posts are assembled in the upper-right and lower-left corners. 2. Keep the lever level as illustrated, and then direct the protruded corners of the fixing plate to the trough of the lever axis, placing the fixing plate in the lever axis. t this point, the protruded corner will lean on the upper-right support for a right-hand door and the upper-left support for a left-hand door. 3. Place the rotating plate onto the screw posts with the arrow above the square hole of the direction changer pointing to the end of the lever. 4. Fasten the 2 rotating plate screws as illustrated. 5. Place the spring in the square hole of the rotating plate and then insert the exterior spindle into the lever as illustrated. Caution : Please rotate the lever downward to check whether it functions normally. If the lever cannot be rotated downward, this indicates that the rotating plate is in the wrong direction. To correct this, simply take off the rotating plate and rotate it before re-inserting it. Optional ccessories ( Reinforcement Plate/Special Strike) If the door slot thicker than 45mm, please install Reinforcement Plate into strike to prevent to malfunction of lock case. 1. If the door slot with a thickness within 45-75mm, please install strike liner thickness 20mm. 2. If the door slot with a thickness within 75-105mm, please install strike liner thickness 50mm. (2mm) (5mm) Special strike Direction of the fixing plate for right-hand door Direction of the fixing plate for left-hand door Rotating Plate Fixing screw Screw post Fixing plate 3 4
6.First pull the IC wire through the upper wire exit hole to the room side and then insert the exterior spindle of the exterior lock body into the square hole that corresponds to the latch to mount it to the door, with the screw posts penetrating the latch. 7.Lift the lock cylinder cover from its bottom before pulling straight down and then rotate the lock cylinder into the latch to temporarily position the exterior lock body. 9. Cylinder Installation 1.Fasten the lock cylinder clockwise into the threaded latch so that the surface of the lock cylinder is flush with the edge, with the keyhole located at the 6 o'clock position. Caution : To prevent the damage of the cylinder, do not insert a flat head screwdriver while rotating the lock cylinder. 2.On the side of the lock case, use a screwdriver to fasten the lock case. Use the key to turn the cylinder to make sure that the latch bolt operates smoothly. Cylinder Exterior spindle Spring 8. Interior Spindle ssembly Installation 1. djust the direction of the arrow on the rotating plate so that it points to the end of the lever and then insert the interior spindle into the rotating plate as illustrated. 2. With the interior spindle inserted into the square hole of the lock case, press the rotating plate against the door and fasten it with 2 screws for screw posts. Caution : Please rotate the lever downward to check if it functions normally. If the lever cannot be rotated downward, this indicates that the direction changer is in the wrong direction. To correct this, simply take off the direction changer and rotate it before re-inserting it. Wire for the outside Lock body 3.Closing the cylinder cover: as illustrated, push the cover upward to the top before pressing it in from the bottom install the faceplate, which is fastened with 2 front faceplate screws. Wire for the lock case Interior spindle Rotating plate Wire for the lock case 5 6
10. Door Handing Determination Regardless whether the door opens inward or outward, you should take "the exterior side of the door" is taken as the reference, and the position of the door hinge is based upon it. Hinge Left-hand door Inward opening door The exterior side of the door Outward opening door Hinge Hinge Hinge Right-hand door Left-hand door The exterior side of the door Right-hand door 2. Keep the interior lever horizontal as illustrated, aim the square hole at the interior spindle. Meanwhile, point the turn piece stem to the square hole of Latch and fix the interior lock body with 2 mounting screws. Caution: 1. Neither cables cannot be pinned under the interior lock body nor pierced by the screws. 2. If the interior lock gasket (optional spec) separated, please press the gasket on the upper and lower side of the lock body first, and the middle. Interior Lock Body Flipping the Latch Bolt (Please refer to Step 2 and 3 if the direction of the latch bolt is to be flipped during assembly.) 1 2 3 4 Interior Lever 12. Securing the Interior and Exterior Levers Use the hex wrench provided to fasten the screws on the axes of the interior and exterior levers. The Interior The Exterior (The beveled side of the latch bolt pointing in the direction the door closes) 1.Take off the faceplate. 2. Pull out the latch bolt and rotate it 180 clockwise or counterclockwise. 11. Interior Lock Body Installation 1. Place the spring in the square hole of bottom of the Interior Lever, connect the 3 different set of cable, 3 pin cable from exterior lock body, 6 pin and 2 pin cable from latch with the PCB of interior lock body. nd tuck the spares into the blank of the lock body. 3.fter verifying its position, push the latch bolt back into the latch to complete the flip. (3 pin) 4. Put back and fasten the faceplate with screws. 13. Battery Installation 1. Place 4 /1.5V batteries into the battery holder on the top of the lock body in correct orientation as marked on the battery holder. lkaline batteries are recommended. 2. Replacing the batterycover: press the battery cover into the lock body by first aiming its 4 pins at the 4 holes of the lock body and then push down. Caution : The connector of the cable is direction-specific. If unable to connect it, please change the direction and try again. 14. Nameplate Remove the film on the back of the nameplate and affix the nameplate at the indicated position. Nameplate (6 pin) (2 pin) 7 8
Setup Description Card Low-battery Indicator Card Sensing rea Status Indicator Entry Prohibition Indicator Mode Switch utomatic Locking/General Battery Cover Thumb Turn Hidden Touch Keypad rea Start Button Password Learn Button Card Learn Button Keyhole 9 10
Setup for Use Before the first time you use it, please erase all cards and passwords prior to use to assure that all cards are authorized by you. For the steps for erasing cards and passwords, please refer to "3. Erasing ll Cards and Passwords". 1.Card Registration 1.Gently press the Card Learn Button (right). You will hear a beep. 2.4 numbers on the keypad will light up. Please press each of the 4 numbers one time in any order. You will hear a beep. Note : lit-up numbers will go dark once it is pressed. 3.Read the card once to register it. You will hear a beep. 4.Repeat Step 2 one time. 5.Repeat Step 3 one time to complete the registration of the card. Note : ] One card can be enrolled each time, and a maximum of 32 cards can be enrolled. { To quit card enrollment midway through, just press the Card Learn Button (right) again. You will hear 2 short beeps. } If two short beeps are heard following the completion of Step 5, then enrollment has failed. Please retry! 2.Password Setup Before a password can be set, the card must go through the card enrolment procedure. Please prepare a card that has been enrolled. 1.Gently press the Password Learn Button (left). 2.fter two beeps sound, the entire touch keypad will light up and the green "status" indicator light will flash. 3.Enter a 4-8 digit password (1st entry) and press the # key when finished. 4.2 beeps will sound. 5.Repeat Step 3 once. 6. single beep will sound upon completion Note : if two long beeps are heard, there has been an inconsistency between the 1st and 2nd password entry. When this happens, the password needs to be reset. 7.Put the card close to the Card Sensing rea to hear the beep, indicating the completion of password setup. Note : ] Every password needs a card and one card can only learn one password, please do not subject the card or the password to multiple use. { One set of passwords can be set each time, and a maximum of 32 sets of passwords can be set. } If you want to quit the password learning mode in the midway, just press the Password Learn Button (left) again. 2 short beeps will sound. If you heard 2 short beeps after step7, the password setting have failed. please reset it again and make sure your card has been enrolled. 3.Erasing ll Cards and Passwords 1. Hold down the Card Learn Button (right). 2. beep will sound. 3. Release the button after hearing 2 beeps five times at 2 seconds intervals following by a succession of 10 short beeps. 4. ll cards and passwords have been erased. Please re-enroll the cards and reset the passwords. ] Prior to your initial use of the device, you should first execute this procedure to ensure that all cards and passwords are authorized by you. { The entire card and password erasing progreess will take about 10s. } You cannot erase just a single card or a single set of passwords at a time. 4. Changing the Password The steps is as same as Password Setup. 5.Entry Prohibition When an incorrect password entry occurs 3 times, the keypad will be locked automatically for 3 minutes. During this period, the Entry Prohibition indicator (green) on the upper right hand corner of the panel will flash 5 times successively if the Start button is pressed. Removal of Entry Prohibition : Simply have a valid card read once for removal. 6. Unlocking The door can be unlocked from the outside by using the Mifare card, the password or the key. The door can be unlocked from the inside by turning the interior lever. Opening from the outside By card ] Hold the card close to the sensing area on the top of the lock body (within 1~2cm). { single beep indicates a valid card (2 beeps for an invalid card). } Turn the lever to unlock. By password ] Press the Start button on the touch keypad. { 4 numbers will appear on the keypad. } Press each of the 4 numbers once in any order until the numbers disappear. Enter the correct password after all keys have lit up and then press the # key. single beep indicates that the password is correct (2 beeps indicate a wrong password). «Turn the leve to unlock. By key ] Open the lock cylinder cover from the bottom. { Pull the cover down to the bottom. } Insert a key to unlock. Put back the cover by following the above steps in reverse order. 11 12
Opening from the inside Simply turn the lever to unlock. 7. Locking The door can be locked from the outside by pressing the Start button, using a valid card or key, or activating the utomatic Locking function. The door can be locked from the inside by turning the interior thumb turn. Locking from the outside ny one of the following: ] Press the Start button once. { Have a valid card read (non-applicable when utomatic Locking is activated). } Use a key to lock. Shift to the utomatic Locking mode (for details, please refer to 8. utomatic Locking). Locking from the inside Turn the interior thumb turn 9.Low Battery lert s the battery power falls below a certain level, a long beep is emitted after every locking or unlocking, and the Low Battery indicator (red) on the upper left corner of the panel lights up, indicating a low battery level. Please change the batteries immediately. 10.Battery Replacement ] Press the bottom of the battery cover and then push upward. { Make off the battery cover and change the batteries. } Replace the battery cover by reversing the steps. Note : ] Please use (LR03) alkaline batteries to ensure a long and steady power supply. { Please do not mix old and new batteries or with non-alkaline batteries or include batteries of different brands. } Changing the batteries will not affect card and password setups in any way. General utomatic Locking 8. utomatic Locking utomatic Locking can be set via the mode switch on the interior side. In utomatic Locking mode, after you shut the door, it will lock automatically. Note: The mode switch in the upper position is utomatic Locking mode and in the lower position is General mode. General Mode ] When the switch is down, general mode is on. { In general mode, if none of the procedures described in 7. Locking is applied after the door is unlocked, then the exterior lever remains capable of opening the door. 11.Backup Power backup battery slot is located at he bottom of the outside lock body. When the batteries run out, a 9V battery can be used as backup power to open the door. Usage : Plug the 9V battery into the backup battery slot (orientation being irrelevant) for power. utomatic Locking Mode ] utomatic Locking mode is when the mode switch is up. { In utomatic Locking mode, the door is locked automatically once it is closed. Note : Once you've set it to the utomatic Locking mode, please remember the passwrd or carry the card or key with you to prevent being locked out following automatic locking. } utomatic locking security mechanism: In utomatic Locking mode, whether unlocking by card or by password, the door will be re-locked if it is not opened in 10 sconds. The main mechanism driving the automatic locking of the door involves the movement of the guard bolt and thus, the use of the strike provided by the manufacturer is highly recommended. 13 14
Troubleshooting & Troubleshooting & If The Generally Please I always hear 5 beeps after each operation and the indicator in the middle flashes a yellowish red light. What does it mean? this problem continues, please contact the distributor for assistance as soon as possible. While testing the lock after installing it, I discovered it going unresponsive to any subsequent card reading after the initial one. Is it malfunctioning? First, please make sure that the lock is in general mode, with the mode switch (automatic locking/general) pushed to the bottom. Then, determine if it functions normally by having a card read. Generally speaking, this situation usually occurs as a result of the user's failure to close the door while testing the automatic locking function. In automatic locking mode, how long the door will be automatically re-locked if the door is not opened right away following the reading of a valid card? door will be re-locked automatically after 10 seconds if not opened. Errors continue to occur as I enter a valid password. How do I troubleshoot? speaking, this may be owing to the accidental pressing of other keys. Resetting the password is recommended. If the same situation also occurs when others enter passwords, please contact the distributor. How to modify the password while entering the wrong number? press the "*" key to clear all the numbers entered previously and input the correct password again. Why would the numbers "1" and "7" on the keypad light up and the keypad become nonfunctioning when using the password to unlock the door? This occurs because the process took too long. When using the password to unlock the door, please finish entering the password within 30s. Numbers "1" and "7" will automatically light up if more than 30s pass. Please wait 10s before retry. No. I use the password to open the door, but I see the key-shaped icon (the Entry Prohibition indicator) flashing on the panel every time I press the Start button. This is because someone previously tried to open the door with invalid passwords (3 times at least). Method 1 : Open the door with a valid card. The lockout will be automatically relieved. Method 2 : new attempt will be permitted after a wait of 3 minutes. When a proximity card has been enrolled multiple times, would this lower the allowable number of registrations? The system is capable of identifying the proximity card as an enrolled one. ll the related setups remain unchanged. fter each operation, I always hear 10 beeps and see a red battery-shaped icon appearing on the left hand side of the panel with locking occurring automatically while in general mode. What does this mean? This indicates that your batteries will soon be depleted. Please replace the batteries immediately to avoid being unable to open the lock. In addition, if the batteries are not changed immediately, the system will execute automatic locking to ensure the security of your home. 15 16