DEVELOPMENT OF A TWO-WAVELENGTH CW RED SEMICONDUCTOR LASERS IN ORIGINAL RESONATOR ARCHITECTURES

Similar documents
DEVELOPMENT OF A NEW INJECTION LOCKING RING LASER AMPLIFIER USING A COUNTER INJECTION: MULTIWAVELENGTH AMPLIFICATION

R. J. Jones Optical Sciences OPTI 511L Fall 2017

CHAPTER 5 FINE-TUNING OF AN ECDL WITH AN INTRACAVITY LIQUID CRYSTAL ELEMENT

Ph 77 ADVANCED PHYSICS LABORATORY ATOMIC AND OPTICAL PHYSICS

A novel tunable diode laser using volume holographic gratings

Elimination of Self-Pulsations in Dual-Clad, Ytterbium-Doped Fiber Lasers

MASSACHUSETTS INSTITUTE OF TECHNOLOGY Department of Electrical Engineering and Computer Science

Lecture 6 Fiber Optical Communication Lecture 6, Slide 1

Powerful Single-Frequency Laser System based on a Cu-laser pumped Dye Laser

Far infrared generation by CO 2 lasers frequencies subtraction in a ZnGeP 2 crystal.

LOPUT Laser: A novel concept to realize single longitudinal mode laser

High-power semiconductor lasers for applications requiring GHz linewidth source

Ring cavity tunable fiber laser with external transversely chirped Bragg grating

Self-organizing laser diode cavities with photorefractive nonlinear crystals

R. J. Jones College of Optical Sciences OPTI 511L Fall 2017

High brightness semiconductor lasers M.L. Osowski, W. Hu, R.M. Lammert, T. Liu, Y. Ma, S.W. Oh, C. Panja, P.T. Rudy, T. Stakelon and J.E.

Semiconductor Optical Communication Components and Devices Lecture 18: Introduction to Diode Lasers - I

3550 Aberdeen Ave SE, Kirtland AFB, NM 87117, USA ABSTRACT 1. INTRODUCTION

Solid-State Laser Engineering

Experimental Physics. Experiment C & D: Pulsed Laser & Dye Laser. Course: FY12. Project: The Pulsed Laser. Done by: Wael Al-Assadi & Irvin Mangwiza

Optodevice Data Book ODE I. Rev.9 Mar Opnext Japan, Inc.

Quantum-Well Semiconductor Saturable Absorber Mirror

Temporal coherence characteristics of a superluminescent diode system with an optical feedback mechanism

DIODE LASER SPECTROSCOPY (160309)

Basic concepts. Optical Sources (b) Optical Sources (a) Requirements for light sources (b) Requirements for light sources (a)

A CW seeded femtosecond optical parametric amplifier

Multi-wavelength laser generation with Bismuthbased Erbium-doped fiber

Doppler-Free Spetroscopy of Rubidium

Study of Multiwavelength Fiber Laser in a Highly Nonlinear Fiber

Vertical External Cavity Surface Emitting Laser

1. INTRODUCTION 2. LASER ABSTRACT

Wavelength Control and Locking with Sub-MHz Precision

DEVELOPMENT OF CW AND Q-SWITCHED DIODE PUMPED ND: YVO 4 LASER

GaSb based high power single spatial mode and distributed feedback lasers at 2.0 μm

A Novel Multipass Optical System Oleg Matveev University of Florida, Department of Chemistry, Gainesville, Fl

SECOND HARMONIC GENERATION AND Q-SWITCHING

SodiumStar 20/2 High Power cw Tunable Guide Star Laser

IST IP NOBEL "Next generation Optical network for Broadband European Leadership"

Opto-VLSI-based reconfigurable photonic RF filter

THE TUNABLE LASER LIGHT SOURCE C-WAVE. HÜBNER Photonics Coherence Matters.

A new picosecond Laser pulse generation method.

High-frequency tuning of high-powered DFB MOPA system with diffraction limited power up to 1.5W

InP-based Waveguide Photodetector with Integrated Photon Multiplication

High-Power, Passively Q-switched Microlaser - Power Amplifier System

PGx11 series. Transform Limited Broadly Tunable Picosecond OPA APPLICATIONS. Available models

visibility values: 1) V1=0.5 2) V2=0.9 3) V3=0.99 b) In the three cases considered, what are the values of FSR (Free Spectral Range) and

NEW LASER ULTRASONIC INTERFEROMETER FOR INDUSTRIAL APPLICATIONS B.Pouet and S.Breugnot Bossa Nova Technologies; Venice, CA, USA

Lecture 08. Fundamentals of Lidar Remote Sensing (6)

High power VCSEL array pumped Q-switched Nd:YAG lasers

An Optical Characteristic Testing System for the Infrared Fiber in a Transmission Bandwidth 9-11μm

Single-frequency operation of a Cr:YAG laser from nm

STUDIES OF INTERACTION OF PARTIALLY COHERENT LASER RADIATION WITH PLASMA

Active mode-locking of miniature fiber Fabry-Perot laser (FFPL) in a ring cavity

Multi-Wavelength, µm Tunable, Tandem OPO

photolithographic techniques (1). Molybdenum electrodes (50 nm thick) are deposited by

To generate a broadband light source by using mutually injection-locked Fabry-Perot laser diodes

FPPO 1000 Fiber Laser Pumped Optical Parametric Oscillator: FPPO 1000 Product Manual

White Paper Laser Sources For Optical Transceivers. Giacomo Losio ProLabs Head of Technology

EXPRIMENT 3 COUPLING FIBERS TO SEMICONDUCTOR SOURCES

R.B.V.R.R. WOMEN S COLLEGE (AUTONOMOUS) Narayanaguda, Hyderabad.

Lecture 08. Fundamentals of Lidar Remote Sensing (6)

Luminous Equivalent of Radiation

Chapter 14. Tunable Dye Lasers. Presented by. Mokter Mahmud Chowdhury ID no.:

Increasing the output of a Littman-type laser by use of an intracavity Faraday rotator

A continuous-wave Raman silicon laser

B. Cavity-Enhanced Absorption Spectroscopy (CEAS)

Large-Area Interference Lithography Exposure Tool Development

High resolution cavity-enhanced absorption spectroscopy with a mode comb.

Universal and compact laser stabilization electronics

FIBER OPTICS. Prof. R.K. Shevgaonkar. Department of Electrical Engineering. Indian Institute of Technology, Bombay. Lecture: 18.

A Narrow-Band Tunable Diode Laser System with Grating Feedback

A continuous-wave optical parametric oscillator for mid infrared photoacoustic trace gas detection

PHY 431 Homework Set #5 Due Nov. 20 at the start of class

External-Cavity Tapered Semiconductor Ring Lasers

Wavelength Stabilization of HPDL Array Fast-Axis Collimation Optic with integrated VHG

Investigations on Yb-doped CW Fiber Lasers

Coupling effects of signal and pump beams in three-level saturable-gain media

Channel wavelength selectable singleõdualwavelength erbium-doped fiber ring laser

Setup of the four-wavelength Doppler lidar system with feedback controlled pulse shaping

The Lightwave Model 142 CW Visible Ring Laser, Beam Splitter, Model ATM- 80A1 Acousto-Optic Modulator, and Fiber Optic Cable Coupler Optics Project

Multi-pass Slab CO 2 Amplifiers for Application in EUV Lithography

Wavelength Tunable Random Laser E.Tikhonov 1, Vasil P.Yashchuk 2, O.Prygodjuk 2, V.Bezrodny 1

Concepts for High Power Laser Diode Systems

UNMATCHED OUTPUT POWER AND TUNING RANGE

Wavelength switching using multicavity semiconductor laser diodes

Introduction Fundamentals of laser Types of lasers Semiconductor lasers

Department of Electrical Engineering and Computer Science

Optical Gain Experiment Manual

Instruction manual and data sheet ipca h

DESIGN OF COMPACT PULSED 4 MIRROR LASER WIRE SYSTEM FOR QUICK MEASUREMENT OF ELECTRON BEAM PROFILE

Synchronization in Chaotic Vertical-Cavity Surface-Emitting Semiconductor Lasers

Optical Fibers p. 1 Basic Concepts p. 1 Step-Index Fibers p. 2 Graded-Index Fibers p. 4 Design and Fabrication p. 6 Silica Fibers p.

HIGH POWER LASERS FOR 3 RD GENERATION GRAVITATIONAL WAVE DETECTORS

Suppression of Stimulated Brillouin Scattering

Tera-Hz Radiation Source by Deference Frequency Generation (DFG) and TPO with All Solid State Lasers

Laser Beam Analysis Using Image Processing

Instytut Fizyki Doświadczalnej Wydział Matematyki, Fizyki i Informatyki UNIWERSYTET GDAŃSKI

3 General Principles of Operation of the S7500 Laser

Generation of 11.5 W coherent red-light by intra-cavity frequency-doubling of a side-pumped Nd:YAG laser in a 4-cm LBO

PERFORMANCE OF PHOTODIGM S DBR SEMICONDUCTOR LASERS FOR PICOSECOND AND NANOSECOND PULSING APPLICATIONS

Transcription:

DEVELOPMENT OF A TWO-WAVELENGTH CW RED SEMICONDUCTOR LASERS IN ORIGINAL RESONATOR ARCHITECTURES Suat Topcu 1, Yasser Alaily 1, Nadejda Yordanova Kaimakanova, Margarita Angelova Deneva 3, Marin Nenchev. Nenchev 3,4 1 LIRIS - University of Versailles, 78035 Versailles, France PlovdivUniversity, 4 Tzar Assen, 4000 Plovdiv, Bulgaria 3 Technical University Sofia, Branch Plovdiv, 61 bvd St. Peterburg, 4000 Plovdiv, Bulgaria 4 IE-Bulgarian Academy of Science, 7 Tsarigradsko Chausse, 1784 Sofia, Bulgaria Using two original two-cannel resonator architectures we have developed a CW red semiconductor lasers that produce simultaneously in a single beam or/and in separate beams emissions at two independently tunable wavelengths (in the experiments in the range 0.68-0.63 µm). We give the detailed description of the two our interference-wedge based laser scheme that is very effective and simple for realization. As addition, one of them permits simultaneous selection of the two outputs of the semiconductor active medium by a single selective structure thus reducing strongly the amplified spontaneous emission. The peculiarities of the obtained emissions are investigated. The advantages in comparisons with two separate lasers - use of a single expensive laser diode (with AR coated surfaces), low pumping, high efficiency, and natural output in a single beam and the problem - tuning limitation due to the wavelength competition are discussed. The cases of competitive applications of the proposal are carried out. 1. INTRODUCTION Keywords: tunable lasers, two-wavelength emission, CW operation, red semiconductor lasers The natural possibility of the wide gain lasers is to be operated simultaneously and in controlled manner at two or more independently tunable wavelengths in different spectral intervals. This mode of operation (two-wavelength lasers) is earlier realized and studied in details for dye, F-color centers and Ti:Saphhire lasers [e.g. 1]. Many practical applications relate of the use of laser light at two independently tunable wavelengths [e.g. ]. The important case is a Differential Absorption Spectroscopy (DAS) that permits to monitor different corposants of the complex substances, including the atmosphere pollutants such as NO, SO (the known LIDAR variant); the modern and efficient method of laser isotopes separations; nonlinear frequency mixing experiments to produce a sum and difference of wavelengths, in holography, in metrology. The best situation for such applications is when the two emissions are produced in a single beam and simultaneously. Here we describe how by applying our original and effective schemes of two-channel laser resonators, we have realized (and studied) such mode of operation in the CW red diode lasers. The red semiconductor lasers are promising simplest sources for the 1

many of noted applications, competing the He-Ne lasers. In comparison with two separate lasers the advantageous of the two-wavelength lasers are: In technical aspects, what is evident, the two-wavelength laser is simplest and chipper use of a single laser diode with AR coated surfaces and respectively with a high price, use of a single stabilized supply and temperature controlled subsystem. In basic aspects: i) Being the threshold phenomenon, the two-wavelength laser operation needs of low pump power than this one after division to pump two separate lasers. ii) The CW laser output power is proportional to the difference (P pump /P th -1), where P pump and P th are the pump and the threshold power, respectively. This simple relation shows directly that the output power in the each emission for the twowavelength laser is a few times higher than this one obtained in two separate lasers. The disadvantage for the most interesting case of generation in one beams of the two emissions is relate with so called mode-competition effects [1,], essential for homogeneously widened media. The two generations compete nonlinearly and the small unbalance of the losses produces suppression of one of the generations by the other. This limits the tuning of the generations However, in many practical cases one time tuning of both wavelength is sufficient.. NEW SOLUTIONS OF THE TWO-WAVELENGTH RED DIODE LASERS In our consideration we have used a red AR coated front surface laser diode of AMS Technology (model SAL-635), optimized for wavelength of 635 nm. The threshold current of ~ 60 ma, nominal laser operation at 80 90 ma and maximum pumping to 100-110 ma. The realized schemes are related to the our patented earlier basic idea to use in convenient manner an Interference Wedge (IW, or Fizeau Interferometer) as a spectral selector and tuning coupling element for creation two spectral-selective channels laser resonators. Very important property of the IW is that the wavelength of its transmission can be tuned by a simple translation in its plane. This permits, during the tuning, to conserve the direction of the reflection and the Fig.1. Calculated transmission and reflection of the Interference Wedge versus the wavelength (Ref. 1) transmission of the incident beams. Thus, using in convenient manner a series of Interference Wedges we can realized a very attractive and compact Wavelength Devising and Multiplexing system (WDM) with spectrally tunable input-output. Except the application for creation of the two-wavelength laser resonator, this WDM system presents essential potential for applications in optical communication systems. Its basic principle is published earlier by us [1].

The IW in construction is very similar to the Fabry-Perot Interferometer (FPI). In IW the reflective surfaces consists a small angle of ~ 10-5 rad. The properties of this device for laser applications, when is illuminated with a limited diameter beams such the intracavity beams in lasers is studied theoretically and experimentally by us in Ref. 3. In general, they are similar to these ones of the FPI with variable thickness by translation of the IW. The essential practical interest presents the technology, actually under progress, to fabricate very compact IW of sandwich type that presents a sequences of disposed on an optical plate a multi-dielectric reflective layer (reflection R ~ 0.8-0.9), a transparent ~ few µm wedged layer-separator and a second reflective layer, similar to the firs one. The example of the calculated transmission and reflection curves vs. wavelength is shown in Fig.1 for the IW with thickness of 5 µm, R=0.8 with angle of 3.10-5 rad. The illumination is with 1 mm diameter He-Ne laser 1 tun. 1 3? tun. 3?i IW3 IW1 tun. 4 1 i tun. IW4 IW?4? Fig.. Principle scheme of the WDM system with Interference Wedges. beam (at 630 nm). In Fig. are plotted the principle scheme of the discussed above WDM system that uses the series of Interference Wedges as the described this one. Using our WDM system we have proposed two types of two-channel resonator architectures for two wavelength operation of the diode laser both original and presenting en essential advantages. Generally, if the high quality IW with resonant transmission of ~ 0.9 and more are available, we can recommend the very simple and attractive scheme for two-wavelength operation shown in Fig.3. In this scheme, we obtain very easily in practice, with nonprecise alignment two-wavelength operation with collinear and a different output for each generation. The two generations use a single diode with AR coated front face in single supply and crystal-cooled system. For 10 cm length nonselective resonator (without IW 1 ), composed of laser diode, AR coated 0.7 cm lens, that focalized the beam at the end mirror M 1 with reflectivity of 0.84 (~ 0.16 transmission) the threshold current was ~ 60 ma. Note that in parallel intracavity beam the alignment was essentially more difficult with high threshold (75 ma). The laser with focalization operates with the introduced 75% transmission IW 1 and 95 % rerflectivity end mirror M 1 with the threshold of ~ 75 ma. The output is taken from the reflection of the IW 1 and is ~ 70 µw for 90 ma pumping. When we reinjected the reflected beam (PSIL technique [1]) in the opposite direction of the output with a second totally reflected mirror the laser output power reaches 70 µw for 90 ma pumping current. The high threshold (~85 µw) of the parallel beams IW selection diode laser, evident is related with high diameter of the intra resonator beams, of order of 3-5 mm and decreasing transmission of the IW in this case [3]. The laser can be tuned in both cases at ~ 5 nm around 630 nm with a 3

linewidth of the emission of ~ 0.4 nm. The improvement of the laser energetic characteristics essentially, using the modification with focalization (Fig.3) is due to the narrowing of the beam diameters, illuminating the IW and respectively a strong increasing its transmission for the selected wavelength (to ~ 85 %) [3]. The twowavelength scheme can be easily understood from the shown Fig.3. The IW 1 is transmission element for the resonant wavelengths and high reflected element (~ 0.97 and more) for the non-resonant (see Fig.3). Thus, if we reflect back by the second end mirror M the non-resonants wavelength we form the second channel. If in the last is introduced a second interference wedge IW, e.g. similar of IW 1, a second spectral selective channel wit selected non-resonant for IW 1 wavelengths is formed for selection of. Fig. 3. The two-channel resonator with focalization of the intra-resonator beam. The action of the scheme is with the advantage that the illuminated IW 1, beam is with decreased diameters in the IW-es,thus assuring additional laser linewith narrowing. Fig.4 Two-wavelength laser architecture with elimination of reinjection of ASE. The scheme in Fig.4 presents the essential advantage to eliminate the reinjection of the amplified spontaneous emission (ASE). In this case the diode laser is with two AR coated faces. The proposed shame with the beam-splitter BS of 0.5 transmission 4

assures a selection of both laser outputs by a single selective structure and without retrereflection of the ASE. The action of the laser architecture is clear from Fig.4. We have obtained simultaneous two-wavelength laser operation in the scheme in Fig.4. The condition is that in a diode laser the net amplification (amplification minus loses) is equalized, that leads to: σ. Г γ =. γ σ. Г D Where [4] γ = ln R 1 + α. L, γ ln R 1 D = + α. L, Г =, Г =, + D + D 1/ d D = π.( n1 n )., 1 / d D = π ( n 1 n ).. Here σ and σ are the corresponding of 1 and gain coefficients [4], n 1 and n - the refractive indices of the active medium and cladding layers for GaAs laser (n 1 =3.6, n =3.4), d ~ 0.1 µm the thickness of the active layer, α is the loss coefficient and is of ~10-1 cm, the resonator length is of L= 13 cm, R 1 and R 1 are the reflection of the corresponding at 1 and of the end mirrors. 3. THE TWO-WAVELENGTH RED DIODE-LASER OPERATION In the investigation, we use the values of the parameters, given for the Fig.3. The diode-laser emission was produced for P 1,, µw 1 fixed ( 633 nm ) the constant currant of 80 ma. The laser threshold 160 for p.c. 80 ma was 67 ma. Firstly, we block the operation in 140 for p.c. 110 ma 10 the IW channel by inserting a screen in front of 1 100 the IW. The laser output was at single 80 wavelength, selected by the IW 1 3. The maximum 60 output power was ~ 00 µw at 633 nm. By 40 translation of the IW 0 1 we perform the tuning of 0 ~ 5 nm around 633 nm. As a second step, we 633 634 635 636 637 block the mirror M 1 and unblock the operation in, nm (tuned) the IW channel. We obtain the similar laser characteristics and tuning by translation of IW Fig.5. Tuning curves for twowavelength generation. One of the When the two channels are unblocked. wavelengths ( 1 ) is fixed and the second simultaneously, as a rule, the generation in one of ( ) is tuned. For each wavelength the them suppresses the lasing in the other. By slowly losses in the two channels are tilting the mirror M appropriately balanced to produce twowavelength operation. wavelength emission. The wavelength 1 we obtain the two competition was exceptionally strong and needed very precise balance of the introduced losses. The two-wavelength operation was possible only near the gain maximum in a range of ~ 4 nm near 633 nm with linewidth of each emission of 0.1 0.3 nm. The maximum sum energy is slowly lower than of the emission at a single wavelength (e.g. 150µW-170 µw). For each tuning of one of the channel, one of the laser emission is suppressed by the other and 5

to reproduce the two wavelength operation it is necessary a new precise balance of the losses. The output beam, after collimation with lens L 1, has diameter of mm and specific distribution with near rectangular high intensity part along the direction of the diode p-n junction, superimposed on the near homogeneous illumination of the beam spot and a divergence of 3 mrad. The typical tuning curves, obtained when one of the wavelengths ( 1 ) is fixed and the second ( ) is tuned are plotted in Fig.5 (for two pump currents: 80 ma and 110 ma). The wavelength competition is a limitation of the application of this attractive technique. Earlier, using a grating or polarizing schemes, experimental realization of the two-wavelength operation in infrared (~ 830 nm) semiconductor laser is reported in Ref.5. The authors are observed similar strong competition and suggest some reasons for the two-wavelength operation the spatial hole burning effect, filamentation, mode hoping and balanced gain for two emissions. In their point of view, the mode jump process may explain double-mode oscillation. However, they are not presented the temporal investigations. We have investigated the temporal behavior of our two-wavelength red semiconductor laser with resolution to 0 ns. Our conditions permit to observe the temporal behavior of one of the emissions during the two-wavelength operation. This is shown on the oscilloscope traces in Fig.6(a) for 50 ns/div and in Fig.6(b) for 0 ns/div. A 300 MHz LeCroy oscilloscope and nsresolution detector are used, however below 50 ns the oscilloscope trace corresponds to numerical mode of registration with change the real form of the signal. Nevertheless in all cases it can be seen that the wavelength jumping not present. We attribute the possibility for two-wavelength operation with a mechanism of equalized difference gain minus losses for both generations. Fig.6. The temporal behavior of the laser emission at the one of the wavelength during the twowavelength operation. Fig. 7. Actual photograph of a two wavelength CW red diode laser, realizing the scheme given in Fig.3 with visualization of the two intra cavity beams. The labels are given in the figure in the inset. 6

4. CONCLUSION In the present work, we have presented the effective solution of a red twowavelength semiconductor laser that produces simultaneously and in single beam emissions at two independently tunable wavelengths. We have shown for the first time that the two emissions from the single diode are really simultaneous The twowavelength lasers are a simplest and cheaper way to obtain such emission with maximum power for a given pump source used and more energetically efficient. Despite the tuning range limitation due to the mode competition, the CW twowavelength laser developed present interest for many practical applications that do not need of wide tenability in DAS monitoring of the atmospheric corposants, in isotope separation, in non-linear investigations, in holography. 5. ACKNOWLEDGEMENT The work is supported by LIRIS Universite de Versailles Saint-Quentin, NFNI Bulgarian Contracts VUF-1, Ph-1305 and by TU-Sofia Contract 987 ni-17. 6. REFERENCES [1] Louyer Y., J.-P. Wallerand, M. Himbert, M. Deneva, M. Nenchev, Two-wavelength passive self injection controlled opertion of a diode pumped cw Yb:doped crystal lasers, Appl. Optics, Vol. 4, 7, 003, pp. 5463-5476; M.Neveux, M.Nenchev, R.Barbe, J.C.Keller, A Two Wavelength Passively Self-Injection Locked, CW Ti 3+ :Al O 3 Laser, IEEE J. Quant.Electron., Vol.31, 1995, pp.153-160 and references therein [] Demtreder W., Laser Spectroscopy (Basic concepts and Instrumentation), Sec.Edition, Springer, 1996 [3] Stoykova E., M.Nenchev, Fizeau wedge with unequal mirrors for spectral control and coupling in a linear laser, Appl.Optics, Vol. 40, 001, pp. 540-541 and the literature therein [4] Svelto O., Principles of lasers, 5 nd ed., Plenum Press, New York, 000 [5] Lotem H., Z.Pan, M.Dagenais, Tunable dual-wavelength continuous-wave diode laser operated at 830 nm, Appl.Optics, Vol. 3, 1993, pp. 570-573 7