RIXSON ASSA ABLOY 3/4 Template Jamb 1/8 2- R. Max. 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L 1-1/4 Dia. Installation Instructions 50 (06-09) Finish Plate 340 TOP PIVOT Pivot Shown Engaged 9/16 1/16 1/4 1-15/32 15/32 21/32 1/4-20 x " FHMS or #14 x 1/2" FHWS Floor Plate 50 Floor Closer Center Hung Single or Double Acting Non-Handed 6-3/4 JAMB PORTION 4-1/2 12-24 x " FHMS or #12 x 1-1/4" FHWS 1-1/8 DOOR PORTION Floor Plate 4-1 5- Cement Case 1-5/16 1/4-20 x " FHMS or #14 x 1-1/2" FHWS 1-1/4 1-3/8 Min. Clearance Required for, Plate H and Shims 7/8 Door Mortised 1-9/16 Deep for 1/8 2- Provide 3/8 Dia. Hole 1-1/16 (11/16 w/ Threshold) Plate 10-3/4 7-7/16 Fasten Front Mounting Screws First 19-1/4 7/16 With Threshold Use Top (2) Holes Cement Case With Floor Plate Use Bottom (2) Holes 1-9/16 2 4-3/8 WITH FLOOR PLATE Set Cement Case Flush with Finished Floor See Note 5 Door Mortised Deep for A 1/4 Threshold 1-1 1/2 Threshold 1-9/16 See Note 5 B A B 1-1/8 7/8 2-3/4 19-1/8 Threshold 1-1/4 1/4-20 x 1 FHMS or #14 x 2 FWHS (4 Places) Conversion from inches to metric: inch x 25.4. C L 1-25/32 1-7/32 1-1 1-13/32 2-3/32 3-1 ARM PLATE H 11/32 2 See Note 4 Tighten Screw Firmly Washer Adapter WITH THRESHOLD Set Cement Case Flush with Finished Floor Notes: 1. Do not scale drawing. 2. Suitable reinforcing by others. 3. Rixson design threshold available on request. 4. Tighten adjusting screw to notched V line on arm to acquire standard initial location of door. Screw moves door towards and away from jamb to equalize door clearances. 5. Provide dia. holes for alignment screws (2 places). 6. Do not remove grind plate until closer is installed. 7. External stop by others required. 8. All dimensions given in inches.
PAGE 2 How To Determine Hand of Door LH RH Top Pivot Jamb Portion Top Pivot Door Portion IMPORTANT: Use plumb line to make sure that center line of top pivot pin lines up with center line of closer spindle. Face a door swinging open away from you. If it opens to the right, it is right hand. If it opens to the left, it is left hand. Adjusting Screw Plate H Alignment Screws Installation Instructions 1. Locating Closer Door Jamb Position Centerline of Door and A. Measure 2-3/4 out from door jamb on centerline of door. This is the location of the spindle center. 2-3/4 From Face of Jamb to C of L 2. Install Cement Case in Floor LEVEL IN BOTH DIRECTIONS A. Cement case is set flush with finished floor. B. Set cement case with closer in floor and block in position. C. Case should be parallel with center line of door. D. CEMENT CASE SHOULD BE LEVEL. Place levels per Illustration. E. Grout in cement case with closer. Cement should not get between closer and case.
3. Install Top Pivot and Closer PAGE 3 A. Install top pivot in door per template. DOOR B. Install top pivot in jamb per template. Plate H Closer in Floor C. Centerline of pivot pin should line up with centerline of spindle. Use plumb line to assure accuracy. If center lines don t line up, loosen hold down screws (4) and reposition closer. Tighten hold down screws closest to spindle first. Then tighten screws at cylinder end. Note: Closer must be lifted approx. 1/8 before repositioning. D. Mortise door for arm, arm plate H, and wood door arm plate. Refer to template. E. Drill two dia. holes for arm alignment screws. Drill 3/8 hole at heel edge of door for adjusting screw. F. Install arm, arm plate H, and shims if required. Attach arm alignment screws and washers to hold arm in place. 4. Hang Door Top Pivot Pin Centerline of Door 30 Pin Retracting Screw CAUTION: Closer is shipped with "valve" screws down. DO NOT FORCE VALVE DOWN. A. Close both valve screws. NEVER FORCE VALVE SCREW DOWN AS THIS WILL DAMAGE TIP SEATING. B. With arm on spindle, turn spindle until arm is in 30 open position (see illustration). C. Set door on spindle. DO NOT ATTEMPT TO CLOSE DOOR. D. Align two portions of top pivot and turn pin retracting screw clockwise to engage top pivot pin. E. Open door to 60 or more and turn valve screws counterclockwise. Door will then close. F. If necessary, turn adjusting screw at bottom of heel edge of door to equalize side jamb clearances. Adjusting Screw G. Adjust arm alignment screws equally from each side to center door in doorway. Alignment Screws
Closer Adjustment PAGE 4 + - BACK CHECK DELAY F S STROKE LATCH F S F S Closing speeds can be adjusted to suit local conditions and requirements. Label on closer face designates the purpose of each adjustment screw. Adjustments are for speed control. A. The stroke valve allows adjustment from open to 15. B. The latch valve allows adjustment from 15 to closed position. C. IMPORTANT: Back check valve option must be adjusted to vary resistance from light to firm at 70 of door opening. D. The delay valve option allows closing speed adjustment from open position to 65. Repairs, parts replacement or internal adjustments must be done by a Rixson authorized repair agency. Consult for an authorized repair agency in your area. Rixson is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright 2005, 2009, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. RIXSON ASSA ABLOY
RIXSON 3/4 ASSA ABLOY Template 1/8 1-7/16 1-1/32 2-2-3/4 7/8 Dia. 1-1/4 Dia. TOP PIVOT Installation Instructions 50W (06-09) Finish Plate 9/16 1/16 1/4 1-15/32 15/32 21/32 1/4-20 x " FHMS or #14 x 1/2" FHWS W50 Floor Closer Center Hung Single or Double Acting Non-Handed Wood Door Installation 6-3/4 JAMB PORTION 12-24 x " FHMS or #12 x 1-1/4" FHWS 1-1/8 DOOR PORTION 4-1 5-1-5/16 1/4-20 x " FHMS or #14 x 1-1/2" FHWS 1-1/4 Jamb 2- R. Max. C L Floor Plate 4-1/2 Provide 9/16 Dia. Hole for Alignment Screw Floor Plate 1-3/8 Min. Clearance Required for, Plate H and Shims 1-1/4 Door Mortised 1-7/8 Deep for Cement Case Shim Plate 7/16 Wood Door Plate Shoulder Collar Fasten Front Mounting Screws First 19-1/4 1/8 2-9* 2-1/4* 7-7/16 *Mortised Provide 3/8 Dia. Hole Use Top (2) Holes Cement Case 2 4-3/8 WITH FLOOR PLATE Set Cement Case Flush with Finished Floor Provide 9/16 Dia. Hole for Alignment Screw Door Mortised Deep for A B 1/4 Threshold 1-3/4 1-1/8 1/2 Threshold 1-1/2 7/8 B A 2-3/4 19-1/8 Threshold 2-3/32 1-25/32 9/16 1-1 C L 4-7/32 1-7/32 C L Door 1-13/32 6-7/32 10-1/2 WOOD DOOR ARM PLATE Conversion from inches to metric: inch x 25.4. #14 x 2-1/2 FWHS (6 Places) 11/16 1-3/8 See Note 4 Tighten Screw Firmly WITH THRESHOLD Set Cement Case Flush with Finished Floor Notes: 1. Do not scale drawing. 2. Suitable reinforcing by others. 3. Rixson design threshold available on request. 4. Tighten adjusting screw to notched V line on arm to acquire standard initial location of door. Screw moves door towards and away from jamb to equalize door clearances. 5. Auxiliary stop required. 6. All dimensions given in inches.
PAGE 2 How To Determine Hand of Door LH RH Top Pivot Jamb Portion Top Pivot Door Portion Shim Plate H IMPORTANT: Use plumb line to make sure that center line of top pivot pin lines up with center line of closer spindle. Wood Door Plate Face a door swinging open away from you. If it opens to the right, it is right hand. If it opens to the left, it is left hand. Adjusting Screw Plate H Alignment Screws Installation Instructions 1. Locating Closer Door Jamb Position Centerline of Door and A. Measure 2-3/4 out from door jamb on centerline of door. This is the location of the spindle center. 2-3/4 From Face of Jamb to C of L 2. Install Cement Case in Floor LEVEL IN BOTH DIRECTIONS A. Cement case is set flush with finished floor. B. Set cement case in floor and block in position. C. Case should be parallel with center line of door. D. CEMENT CASE SHOULD BE LEVEL. Place levels per Illustration. E. Grout in cement case with closer. Cement should not get between closer and case.
3. Install Top Pivot and Closer PAGE 3 A. Install top pivot in door per template. DOOR B. Install top pivot in jamb per template. Shim Plate H Closer in Floor Wood Door Plate C. Centerline of pivot pin should line up with centerline of spindle. Use plumb line to assure accuracy. If center lines don t line up, loosen hold down screws (4) and reposition closer. Tighten hold down screws closest to spindle first. Then tighten screws at cylinder end. Note: Closer must be lifted approx. 1/8 before repositioning. D. Mortise door for arm, arm plate H, and wood door arm plate. Refer to template. E. Drill two 9/16 dia. holes for arm alignment screws. Drill 3/8 hole at heel edge of door for adjusting screw. F. Attach arm to spindle using spindle screw supplied and tighten securely. Install arm plate H, wood door arm plate, and shim. 4. Hang Door Top Pivot Pin Centerline of Door 30 Pin Retracting Screw CAUTION: Closer is shipped with "valve" screws down. DO NOT FORCE VALVE DOWN. A. Close both valve screws. NEVER FORCE VALVE SCREW DOWN AS THIS WILL DAMAGE TIP SEATING. B. With arm on spindle, turn spindle until arm is in 30 open position (see illustration). C. Set door on spindle. DO NOT ATTEMPT TO CLOSE DOOR. D. Align two portions of top pivot and turn pin retracting screw clockwise to engage top pivot pin. E. Open door to 60 or more and turn valve screws counterclockwise. Door will then close. F. If necessary, turn adjusting screw at bottom of heel edge of door to equalize side jamb clearances. Adjusting Screw G. Adjust arm alignment screws equally from each side to center door in doorway. Alignment Screws
Closer Adjustment PAGE 4 + - BACK CHECK DELAY F S STROKE LATCH F S F S Closing speeds can be adjusted to suit local conditions and requirements. Label on closer face designates the purpose of each adjustment screw. Adjustments are for speed control. A. The stroke valve allows adjustment from open to 15. B. The latch valve allows adjustment from 15 to closed position. C. IMPORTANT: Back check valve option must be adjusted to vary resistance from light to firm at 70 of door opening. D. The delay valve option allows closing speed adjustment from open position to 65. Repairs, parts replacement or internal adjustments must be done by a Rixson authorized repair agency. Consult for an authorized repair agency in your area. Rixson is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright 2005, 2009, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. RIXSON ASSA ABLOY