CHERRYLOCK 'A' BLIND RIVET SPS Fastener Division, a PCC Company
CONTENTS CHERRYLOCK 'A' RIVET NAS1/1(A) CODE CR2172/7 ALUMINUM CR2572/7 MONEL CR2672/7 A-26 Features... 1 Installation... 1 Physical Properties... 2 Numbering System... 2 Materials... 2 Strength... 2 Installed Weights Pounds per 1000 pieces... Wiredraw Nominal NAS1 100 Flush Head... Wiredraw Nominal NAS1 Universal Head... 5 Installation Tooling... 6 Power Riveters... 7 Hand Riveters... Pulling Heads... LIMITED WARRANTY Seller warrants the goods conform to applicable specifications and drawings and will be manufactured and inspected according to generally accepted practices of companies manufacturing industrial or aerospace fasteners. In the event of any breach of the foregoing warranty, Buyer s sole remedy shall be to return defective goods (after receiving authorization from Seller) for replacement or refund of the purchase price, at the Seller s option. Seller agrees to any freight costs in connection with the return of any defective goods, but any costs relating to removal of the defective or nonconforming goods or installation of replacement goods shall be Buyer s responsibility. SELLER S WARRANTY DOES NOT APPLY WHEN ANY PHYSICAL OR CHEMICAL CHANGE IN THE FORM OF THE PRODUCT IS MADE BY BUYER. THE FOREGOING EXPRESS WARRANTY AND REMEDY ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES; ANY IMPLIED WARRANTY AS TO QUALITY, FITNESS FOR PURPOSE, OR MERCHANTABILITY IS HEREBY SPECIFICALLY DISCLAIMED AND EXCLUDED BY SELLER. This warranty is void if seller is not notified in writing of any rejection of the goods within one (1) Year after initial use by buyer of any power Riveter or ninety (0) days after initial use of any other product. Seller shall not be liable under any circumstances for incidental, special or consequential damages arising in whole or in part from any breach by Seller, AND SUCH INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES ARE HEREBY EXPRESSLY EXCLUDED. Our policy is one of continuous development. Specifications shown in this document may be subject to changes introduced after publication. CHERRY, Cherrylock and MAXIBOLT are trademarks of Cherry Aerospace. NOTE The properties, strengths, dimensions, installed characteristics and all other information in this catalog is for guidance only to aid in the correct selection of the products described herein and is not intended or implied as part of the warranty. applications should be evaluated for functional suitability and available samples of the described parts can be requested for installed tests, suitability and evaluations. ATTENTION Blind rivets are not always a suitable substitute for solid rivets. Maintenance personnel are reminded that AC.1-1A chapter 2, section, stipulates: Do not substitute hollow rivets for solid rivets in load carrying members without specific approval of the application by a representative of the Federal Aviation Administration. Blind rivets may be used in blind locations in accordance with the conditions listed in Chapter 5, provided the edge distances and spacings are not less that the minimum listed in paragraph d.
CherryLOCK A Code non-shift, self-plugging blind rivets provide excellent hole-fill and sheet take-up capability conforming to the Procurement Specification NAS 100 and Standards Pages NAS 1 and NAS 1. The rivets are available in aluminum, monel and A-26 stainless steel materials in a wide variety of diameters and grip ranges. CherryLOCK A Code wiredraw rivets are manufactured in /2", 1/", 5/2", /16" and 1/" diameters in 100 flush head and protruding head style configurations and offer grip ranges from.020 in the smaller diameters to 1.07 in the larger diameters. The /2" diameter rivet is available in A-26 only with grips ranging from.020 to.562. Rivets 1/" diameter and larger have head markings to identify grip, material and manufacturer for ready inspection. The flush fracturing spindle eliminates the need for shaving and meets the flushness requirement of the NAS 100 specification. Each rivet is provided with its own locking mechanism that positively retains the plug section meeting specification push-out values and assuring no lost stems. These rivets allow simple installation with a wide variety of Cherry nonshifting and shifting tools. A complete range of recommended power tools, hand tools and pulling heads are described in the back section of this catalog. CHERRYLOCK 'A' RIVET FEATURES INSTALLATION OF CHERRYLOCK A CODE 1
CHERRYLOCK 'A' RIVET PHYSICAL PROPERTIES NUMBERING SYSTEM CR2672CW - -02 Maximum Grip Length in 16ths of an inch (-0 = /16"=.250) Shank Diameter -(.10), (.17), (.201) Cherry Part Number (Material, Head Style, Series) MATERIALS CherryLOCK A rivets are manufactured in a wide variety of materials in order to give the user the widest possible choice for optimum design. Rivet Material Ultimate ShearStrength (at room temp) Typical Max Temperature Use (in F) Sleeve Stem 2017 Aluminum 7075 Aluminum,000 psi 250 Monel Monel 55,000 psi 00 A-26 CRES A-26 CRES 75,000 psi 1200 STRENGTH Minimum Ultimate rivet shear and tensile strength (lbs.) per NAS 100 CherryLOCK A Rivets Aluminum CR2172 CR217 Single Shear Tensile /2" 1/" 5/2" /16" 1/" /2" 1/" 5/2" /16" 1/" 755 100 170 20 75 50 1000 Monel CRES CR2572 CR257 CR2672 CR267 710 100 150 20 0 550 70 150 5 70 10 2150 0 00 60 1000 1500 2700 NOTES: Values shown are fastener capabilities only Consult Mil-Hdbk for joint design allowables /2" DIAMETER RIVETS AVAILABLE IN CR2672 AND CR267 ONLY NAS/Cherry Part Number Cross Reference Guide NAS1C( )A( ) / CR2672-( )-( ) NAS1C( )A( ) / CR267-( )-( ) NAS1CW( )A( ) / CR2672CW-( )-( ) NAS1CW( )A( ) / CR267CW-( )-( ) NAS1D( )A( ) / CR2172-( )-( ) NAS1D( )A( ) / CR217-( )-( ) NAS1M( )A( ) / CR2572-( )-( ) NAS1M( )A( ) / CR257-( )-( ) NAS1MW( )A( ) / CR2572P-( )-( ) NAS1MW( )A( ) / CR257P-( )-( ) 2
CHERRYLOCK 'A' RIVET INSTALLED WEIGHTS Pounds per 1000 pieces Dash Number CR2172 CR217 CR2572 CR257 CR2672 CR267-01.6-02.60.76-0.71.6-0..7-05.6 1.0-06 1.0-01.20.7.5 1.2. 1.26-02.2.52 1.25 1.7 1.10 1.52-0.72.61 1.5 2.02 1.6 1.7-0.562.70 1. 2.2 1.62 2.0-05.657.02 2.1 2.62 1. 2.1-06.77. 2. 2.1 2.15 2.57-07.27 2.7 2.1-0 5-01.70 2. 2.10 5-02.622.72 2.0 2.5 1.7 2.51 5-0.76 1.01 2..0 2.20 2.1 5-0.0 1.15 2.5.77 2.60.2 5-05 1.0 1.0.0.2.00.7 5-06 1.1 1..7.6.1.1 5-07 1. 1.5. 5.15.2.5 5-0 1.7 1.72.0 5.62.2.5 5-0.6 5-10 5.05 6-01 1.12.6.2 6-02.5 1.2.0.2 2.72.1 6-0 1.15 1.5.7..0. 6-0 1.5 1.72.2 5.62.7.6 6-05 1.55 1.2 5.05 6.2.5 5.5 6-06 1.75 2.12 5.71 6. 5.0 6.11 6-07 1.5 2.2 6. 7.5 5.61 6.6 6-0 2.15 2.52 7.02.2 6.1 7.27 6-0 2.5 2.7 7.66.1 6.76 7.5 6-10 2.55 2.2.2.55 7..2 6-11 2.7.1.6 10.21 7.0.00 6-12 2.5.2.61 10...56 6-1.05 6-1.62-01 -02.00.7.62-0 2.56.5.5 10.5 7.7.65-0 2.2.72.5 12.1.1 10.70-05.2.07 10.72 1.27.5 11.70-06.65.5 11.1 1. 10. 12.0-07.00.7 1.0 15.62 11.5 1.0-0.7 5.1 1.2 16.76 12.57 1.0-0.72 5.52 15.2 1.02 1.61 15.0-10 5.07 5.7 16.56 1.15 1.65 16.0-11 5.6 6.22 17.0 20.2 15.6 17.0-12 5.0 6.57 1.0 21.2 16.7 1.0-1 6.15 6.5 20.0 22.6 17.77 20.00-1 6.52 7.2 21.2 2.1 1.1 21.00
100 ±1 ALUM. 100 ±1 1 /2 MONEL AND A26 CHERRYLOCK 'A' RIVET WIREDRAW NOMINAL NAS1 100 FLUSH HEAD.010 R. MAX ALUM..020 R. MAX MONEL AND A26 C Dia A B D Hole Limits C Dash No. ±.00 Ref. +.00-.001 Min Max Alum. oy Monel or A-26 -.17.06.0.07.101.002.006 -.225.02.125.12.12.002.006.26.055.156.160.16.002.006.005.015.5.070.17.12.16.002.006 -.76.05.250.256.261.002.006 Grip Dash Grip Range - Diameter - Diameter Diameter Diameter - Diameter No. Min Max L Max K Max BK L Max K Max BK L Max K Max BK L Max K Max BK L Max K Max BK -02.125.22.0.25.260.5.0.26..2.27..26-0.126.17.21.505.2.2.57.5.26.56..50.60.2.5.6.7-0.1.250.5.620.0 5.6.1..67..12.72.7..75. -05.251 12.16.75...1.6.51.7.5.75...510.7. -06.1.75.7.50.5.510..52.51.1.50.57.5..57..5-07.76.7.52.65..57 1.0.57.576 1.0.56.600 1.07.5.65 1.11.60-0..500.605 1.00.550.6 1.15.62.662 1.1.60.6 1.2.65-0.501.562.66 1.15.60.701 1.27.67.725 1.1.65.760 1..71-10.56.625.76 1..7.77 1..76.2 1.52.2-11.626.67.50 1.60.2.5 1.6. -12.6.750.12 1.72.. 1.77. -1.751.12.75 1.. 1.010 1. 1.00-1.1.75 1.07 1.5 1.00 1.07 2.01 1.06 NAS Material Finish Part No. NAS No. 52 Code Sleeve Stem Lock Ring Sleeve Stem Lock Ring CR2172 1D ACF 2017-T PER 5056-H PER ANODIZE PER MIL-A25 OR CHEM FILM 7075 PER QQ-A-0 QQ-A-0 QQ-A-0 CHEM FILM PER MIL-C51 PER MIL-C51 NONE CR2572 1M ACT MONEL PER QQ-N- NONE MONEL: NONE MONEL PER 21 OR A26 PER MONEL PER CAD PLATE PER QQ-P-16 CR2572P 1MW ACK A26 PASSIVATE PER QQ-N-21 AMS 571 OR QQ-N-21 TYPE II, CL2 AMS 2700 CR2572S 1MS ACV AMS 572 SILVER PLATE PER QQ-S5 NONE CR2672 1C ACX A-26 CRES PASSIVATE PER AMS 2700 A-26 CRES PER MONEL PER CR2672CW 1CW AFE PER AMS 571, CAD PLATE PER QQ-P-16 AMS 571 QQ-N-21 CR2672S 1CS AFF 572, 577 SILVER PLATE PER QQ-S5 PASSIVATE PER AMS 2700 NONE An increase of 0.001 permissible within 0.100 of base of head. Minimum blind side clearance for satisfactory installation. Material designation refers to chemical composition only. Minimum grip for - diameter is.06, for diameter is.065 and for diameter is.00. Single digit marking is permissible, at manufacturer s option, for grip dash (-) numbers less than 10. No head marking for - diameter rivet. NOTES: Single sheet thickness for machine countersunk holes shall not be less than B +.010. 6. Some longer grip lengths are manufactured only on special request.
CHERRYLOCK 'A' RIVET WIREDRAW NOMINAL NAS1 UNIVERSAL HEAD.010 R. MAX ALUM..020 R. MAX MONEL AND A26 A Hole Limits Grip Dash No. Min Min B +.010 -.000 D +.00 -.001 Undercut Min Max -.17.16.00.0 12.07.101 -.2.262.05.125 12.12.12.26.2.067.156 10.160.16.56..00.17.12.16 -.75.525.107.250 6.256.261 Grip Dash Grip Range - Diameter - Diameter Diameter Diameter - Diameter No. Min Max L Max K Max BK L Max K Max BK L Max K Max BK L Max K Max BK L Max K Max BK -01.062.166..2.1..0.201..2.225..27-02.06.125.22..275.260.51.5.26...27.55.2.2.57.7-0.126.17.21.5.1.2.6.1.26.61..50.67.7.5.6. -0.1.250.5.6.50.5.75.6..7.5.12.7...1. -05.251.12.16.7...7.52.51.5.50.75.1..510..5-06.1.75.7..25.510..57.51.7.56.57 1.0.5.57 1.0.60-07.76.7.52..62.57 1.11.6.576 1.0.62.600 1.15.60.65 1.16.65-0..500.605 1.11.500.66 1.2.6.6 1.20.67.662 1.27.65.6 1.2.71-0.501.562.6 1.5.75.701 1..7.725 1..76.760 1.6.2-10.56.625.76 1.50..77 1.56.2.2 1.5. -11.626.67.50 1.6..5 1.70. -12.6.750.12 1.1.. 1. 1.00-1.751.12 1.010 1.5 1.06-1.1.75 1.07 2.07 1.12 Part NAS NAS 52 Material Finish No. No. Code Sleeve Stem Lock Ring Sleeve Stem Lock Ring An increase of 0.001 permissible within 0.100 base of head. Minimum blind side clearance for satisfactory installation. Material designation refers to chemical composition only. Minimum grip for - diameter is.020, - diameter is.025, for diameter is.01 and for diameter is.07. Single digit marking is permissible, at manufacturer s option, for grip dash (-) numbers less than 10. No head marking for - diameter rivet. NOTES: Some longer grip lengths are manufactured only on special request. 5
CHERRYLOCK 'A' RIVET TOOLING Type of Tool Hand Hydraulics Pneumatic Cherry Riveter Model Pulling Head (series) Rivet & Head Dia. Max Grip/Single Stroke Aluminum Monel A26 CRES CR2172 CR217 CR2572 CR257 CR2672 CR267 G27* - G2* - G0 - G750A G700 G77 G70B G76A G7 G6 H055 with 750A-117 Adapter H055 with 60B6 Adapter H55 H55 H55 H055 with 60B6 Adapter H0- with 60B57 Adapter H055 with 60B6 Adapter - - - - - - - - - - - - ** - - - G02 H02-NPR*** - G02-15 H015-C - ** * Use 72-0 Nosepiece (sold separately) ** May require 5 psi ***Use 02-0 Nosepice (sold separately) 6
G76A POWER RIVETER National Stock Number 510-01--0 The Cherry G76A is a pneumatic-hydraulic tool designed for the efficient installation of CherryLOCK A code rivets for the -, -, and diameter rivets. It weighs pounds and can be operated in any position with one hand. It has a.5 inch rivet setting stroke and a rated pull load of 150 pounds on 0 psi air pressure at the air inlet. The G76A consumes approximately. cubic feet of air at 20 cycles per minute and the maximum noise level under load does not exceed 5 db (A). Pulling heads are not furnished with this riveter and must be ordered separately. The G76A with the H55 series (straight) and the H6 series right angle pulling heads can install CherryLOCK A blind rivets in the -, -, and diameters in all materials. CHERRYLOCK 'A' RIVET INSTA LLATION TOOLING 76A Power Riveter.71" (1. mm) G77 POWER RIVETER 10 The Cherry G77 is a pneumatic-hydraulic tool designed specifically for the most efficient installation of CherryLOCK A rivets. Its durable, all metal housing makes this extremely robust tool ideal for use in rugged shop environments. It has many ergonomic features; very light weight (.5 lbs.), comfortable fit in the operator s hand and it can be operated in any position with one hand. Pulling heads are not furnished with this riveter and must be ordered separately. The G77 with the H55 series (straight) and the H6 series right angle pulling heads can install CherryLOCK A blind rivets in the -, -, and diameters in all materials. 2" (50. mm) 11.7" (2. mm).56" (115. mm) G77 Power Riveter G70B RIVETER National Stock Number 510-01--15 The Cherry G70B is a pneumatic-hydraulic tool designed specifically for the most efficient installation of CherryLOCK A rivets. Its durable, all metal housing makes this extremely robust tool ideal for use in rugged shop environments. It has many ergonomic features; light weight (.25 lbs.), comfortable fit in the operator s hand and it can be operated in any position with one hand. Pulling heads are not furnished with this riveter and must be ordered separately. The G70B with the H55 series (straight) and the H6 series right angle pulling heads can install CherryLOCK A blind rivets in the -, -, and diameters in all materials. 70B Riveter 7
G0 HAND RIVETER National Stock Number 5120-01-16-726 For installation of CherryLOCK A Locked Spindle Nutplate Rivets, CR2672 and CR267 Series, - diameter. The Cherry G0 Hand Riveter is an efficient, compact, lightweight and economical tool for installation of CherryLOCK A rivets. Provided with this tool is a special designed nose piece which is essential for the proper insertion of the rivet locking collar. The G0 is.25 long, weighs just 1 ounces and is intended for use where access of power limitations prevent the use of Cherry power tools and generally where smaller quantities of rivets are to be installed. This tool will also install the Cherry CCR26/27 series rivets with a 72A series nosepiece. To operate, insert the serrated stem of the rivet into the nosepiece. Insert the rivet into the application. Sliding the riveter nosepiece firmly and squarely against the rivet head and squeeze the handles to install the rivet. On longer grip rivets, additional strokes will be required. CHERRYLOCK 'A' RIVET INSTALLATION TOOLING G0 Hand Riveter G750A HAND RIVETER National Stock Number 5120-01-21 The H055 series CherryLOCK A pulling heads can be attached to the G750A by utilizing the 750A-117 adapter. The H6 Right Angle Head can be attached to the G750A by use of the 750A-0 adapter. The Cherry G750A hand hydraulic riveting tool provides the versatility of a pneumatic-hydraulic riveter but with the lightweight high pull strength ratio desirability no found in other hand riveters. The Cherry G750A has a unique 2-stage hydraulic power cylinder that provides the user with the ease of puling the handle without the strain normally endured to install a high strength fastener. The patentable 2-stage power feature allows the user to squeeze the handle through the increase power requirement, without feeling the need to squeeze harder to install the fastener. The G750A hand riveter can install a variety of blind fastener styles, diameters, head configurations and material combinations. G750A Hand Riveter
H55 PULLING HEAD FOR CHERRYLOCK A RIVETS National Stock Numbers: 510-01-11-25 H55-510-01-11-260 H55-510-01-11-2600 H55 510-01-11-260 H55 STEM THROUGH FEED The H55 Series pulling heads fit directly on the G701A, G70B, G76A and G77 riveters. The heads in this series are capable of installing /2", 1/", 5/2" and /16" diameter rivets in all materials and head styles and grip lengths. Stems feed through the pulling head and are ejected out the back of the tool. Please refer to the individual tool specification for capacity. CHERRYLOCK 'A' RIVET /" (1.05 mm) 2 /" (60.25 mm) H55 Straight Pulling Head TOOLING H055 PULLING HEAD FOR CHERRYLOCK A RIVETS National Stock Numbers: 510-01-20-065 H055-510-01-20-062 H055-510-01-20-050 H055 510-01-20-05 H055 STEM SIDE EJECTION H055 series pulling heads are available for installation of /2", 1/", 5/2" and /16" diameter locked spindle CherryLOCK A code rivets in all materials, head styles and grip lengths. Stems are ejected from the side of the pulling head. Please refer to the CherryLOCK A rivet tool selection chart on page 6 for possible tool combinations. 5/" (15. mm) /16" (106. mm) H055 Pulling Head H6-,, 5, 6 RIGHT ANGLE PULLING HEADS The H6 series right angle pulling heads fit directly on the G701A, G70B, G76A and G77 power riveters to install CherryLOCK A brand rivets in /2", 1/", 5/2" and /16" diameters in all materials, head styles and up to -0 grip length. NOTE: For 1/" diameter rivets, use the 0- pulling head. See tooling chart on page 6 for possible tool combinations. 2 1/" 57.15 mm) /" (.5 mm) 5 7/16" (1.1 mm) H6 Right Angle Pulling Head
SPS Fastener Division, a PCC Company 122 East Warner Avenue, Santa Ana, CA 2705 www.cherryaerospace.com 2007 Cherry Aerospace Suppliers Federal I.D. Code 1115 CA-102, Rev. A, Date: April 27, 2007, DCR 07-052