SUPER LED F10 165W LED Fresnel SPOTLIGHT (white light, either Tungsten or Dylight lned orrelted olor Temperture) INSTRUTION MANUAL Mnul Operted Pole Operted MANUFATURER REPRESENTATIVE ILT Itly S.r.l. Vi nellier # 10, 00041 Alno Lzile (Rome- Itly). Tel. +39/06/902901 Fx. +39/06/90231051 U.R.L.: www.desisti.it E-mil: desisti@desisti.it 1. INTRODUTION ongrtultions on your purhse of SUPER LED F10 lighting fixture. Our ommitment to Totl ustomer Stisftion nd our onsolidted experiene nd ledership in design innovtion nd mnufturing of lighting produts for the professionl Entertinment Industry mens you n depend upon the qulity of this produt. The SUPER LED F10 is ompt, highly effiient Fresnel lens spotlight using LED ARRAY omined with the DE SISTI Ptented optil system to optimize the photometri performnes of LED ARRAYS when utilized in omintion with either Fresnels or Plno onvex lenses. The Lighting Fixture is DMX ontrolled nd inludes numer of prmeters tht n e set lolly, it is equipped with power supply for A feed (either 100/120V or 200/240V 50/60Hz) nd it is ville with either Tungsten or Dylight Blned T with high power nd high RI. It utilizes Stndrd essories from the DE SISTI rnge of equivlent Fresnel Lens size, suh s Brndoor, olour Frme, ones, srims. This Mnul is pplile to Revised April 2nd 2015 Pg 1.
2. YOKE AND AESSORIES ASSEMBLY SUPER LED F10 (MANUAL OPERATED) 3. POWER AND DMX DAISY HAIN SUPER LED F10 (POLE OPERATED) The SUPER LED F10 permits oth POWER nd DMX DAISY HAIN. In ft eh Fixture is respetively equipped with: For DMX: 1 XLR5 pin Pnel Mount Mle (DMX IN) 1 XLR5 pin Pnel Mount Femle (DMX OUT) For Mins Supply 1 20A Poweron NA3MPA BLUE (POWER IN) 1 20A Poweron NA3MPB WHITE (POWER OUT) It is reommended to Disy hin Mx of 10 fixtures, even if the limittions imposed y DMX Stndrds re for n higher q.ty of units nd even if the Poweron onnetions re rted for 20A mx. This Mnul is pplile to Revised April 2nd 2015 Pg 2.
4. SAFETY INSTRUTIONS Professionl use: This luminire hs een designed for professionl use nd must e operted y qulified personnel only. Not for residentil use. Grounding: WARNING: THIS LUMINAIRE MUST BE GROUNDED WARNING: Disonnet Power ORDS efore ny mintenne work or opening the FUSE HOLDER. Risk of serious injury. Eletril onnetions: IMPORTANT The ores in this mins led re olored in ordne with the following ode: Europe Ameri Ground Green & yellow Green or green & yellow Neutrl Blue White Live Brown Blk In se the olors of the ores do not orrespond to the olors of the onnetion points on your plug, plese proeed s follows: the green or green nd yellow ore must e onneted to the onnetion point mrked with the letter E or with the symol or olored in green or in green - yellow; the lue (or white) ore must e onneted to the onnetion point mrked with the letter N or olored in lk; the rown (or lk) ore must e onneted to the onnetion point mrked with the letter L or olored in red. Working onditions Working Position Lighting fixture: Mx. Tilting 90 from horizontl Amient Temperture, t t the ple of instlltion nd Storge Humidity t the ple of instlltion nd Storge Minimum distnes from inflmmle surfes Minimum 10, mximum +40 25-80% (not ondensing) Top Bk Sides Front 0,3 m. 0,15 m. 0,15 m. 1 m. The luminire should never e OPERATED lose to inflmmle mterils. The ones indited in the ove tle re the minimum distnes reommended. Other requirements for sfe use re: A. Do not over the pertures of the luminire housing. They re essentil for orret ventiltion. B. Use only originl essories nd spres from De Sisti Lighting.. Before hnging the luminire ensure tht the suspension point (or the stnd) is properly rted to ept the luminire weight. D. In se of pole operted use, fit only P.O. stirrup from De Sisti Lighting. E. A suitle seondry sfety suspension devie (sfety le, hin or equivlent) must e fitted etween the suspension point nd the eyelet t the front of the ody. WARNING : DO NOT MOUNT THE LUMINAIRE ON A NORMALLY FLAMMABLE SURFAE. 5. INSTALLATION INSTRUTIONS The following proedure should e dopted: Before onneting the luminire to the eletril mins ensure tht: A. Erth line is present on the power soket. B. The mins voltge is within the rted rnge of the luminire (see tehnil dt on the rting lel). The front sfety shield is present nd in good ondition. It onsists of fresnel lens mde y orosilite untoughened glss, with Dimter = 250 mm, thikness = 7 mm typ ( 4 min ). WARNINGS : Do not operte the produt if the mient temperture exeeds 40 Provide minimum lerne of 0,1m (4 in.) round fns nd ir vents. This Mnul is pplile to Revised April 2nd 2015 Pg 3.
SHIELDS, LENSES SAFETY OR DIHROI GLASSES SHALL BE HANGED IF THEY HAVE BEOME VISIBLY DAMAGED TO SUH AN EXTENT THAT THEIR EFFETIVENESS IS IMPAIRED, FOR EXAMPLE BY RAKS OR DEEP SRATHES. THE LUMINAIRE SHALL ONLY BE USED OMPLETE WITH ITS PROTETIVE SHIELD D. Applying power: Never onnet to dimmer power. Instll power plug on the power le using the following pin ssigment: 1 : Neutrl 2 : Live Green/Yellow : Ground - This fixture must e onneted to ground. Mke sure the lol power voltge is within the rnge speified. If so; onnet the power le nd turn the power on. E. Stnd Alone opertion: Using the nvigtion uttons nd disply redout ( refer to the Lol Menu hpter ) nvigte to Mnul nd set the desired intensity (for dditionl opertions see Lol Menu hpter) F. DMX opertion: onnet DMX le Nvigte to Address mode (Addr) nd set the desired ddress, (refer to the Lol Menu hpter). onnet to DMX ontroller (refer to the hnnel Setting in the Lol Menu hpter) nd Use it. 6. LOAL MENU PGM PORT For Firmwre Upgrde FUNTION 1 Srolling UP / Inreses vlue funtion key ENTER Selet / onfirm FUNTION 2 Srolling DOWN / Dereses vlue funtion key Disply When the push utton re not used for more thn 15 seonds the disply will go OFF. It will go ON gin nytime push utton is tivted. DMX Presene Shows the presene of DMX (LED lit = DMX present) DEFAULT SETTINGS ARE INDIATED IN BOLD LETTERS ON THE FOLLOWING TABLE: The following re the BASI FUNTIONS nd OMMANDS tht re provided on the LOAL MENU of the LED FRESNEL. The unit is provided with USER MENU essile instntly on the produt. The unit hs lso SERVIE MENU tht is only essile through PASSWORD nd is reserved for QUALIFIED nd TRAINED PERSONNEL: 1st MENU Displyed (srolling with the nd the uttons) 2nd MENU Displyed (fter pressing the X tht stnds for ENTER) Explntion of Eh MENU FUNTION DMX ADDRESS This Funtion is to SET the DMX ddress from 1 to 512 (Produt is delivered with defult settingof the DMX ddress t 1) One the 001 is displyed, t on the utton to inrese the ddress to the desired vlue. Temporry push will inrement the vlue y 1, if the utton is kept pushed the inrement on numers is getting fst. One the desired Address numer is omplished press X ( ENTER ) to mke it tive LOAL DIMMING ONTROL This Funtion is to LOALLY DIM the LED INTENSITY from 0 to 100% (Produt is delivered with defult setting of the DIMMER t 0). The intensity goes in inrements of 1/100% so the disply will show 000% with the dimmer t 0% nd FULL with the dimmer t 100%. Temporry push will inrement the vlue y 1/100, if the utton is kept pushed the inrement on numers is getting fst. One the desired Lighting Level is omplished nd it is wnted to leve tht level nd go to other funtions of the MENU, press ENTER. LOAL OR REMOTE ONTROL SETTINGS The LED Fresnel hs the fility to lok the LOAL DIMMING SETTING nd mintin it when the POWER is turned first OFF nd thn ON gin. This llows for the LIGHT to e TUNED nd FOUSED lolly nd its dimming level n e loked, so tht for instne system lighting SET n e operted y remote swith or simple rkers y TURNING POWER ON. The relevnt menu to ess this funtion is TRL, to enter in this menu press X ( ENTER ), it is thn possile to selet either DMX or AUTO y ting on the or utton nd thn press X ( ENTER ) gin. The mhine is set to DMX s defult. In DMX mode: the Fixture epts DMX ontrol.if in this mode the lol DIMMING ONTROL is SET to level the Light ehviour will follow the HTP (Highest Tkes Preedene) modlity, in other words it will keep the lol DIMMING setting until the DMX level of the speifi hnnel will e higher, from tht level onwrds the DMX level will tke preedene. In this ondition if the DMX onnetion is removed, the light will keep the lst level.until power is ON. It will reset nd Strt t 0fter Power OFF nd ON gin. In AUTO mode: the light will ignore ny DMX ontrol. In this mode ny lol dimming setting will e mintined nd will e utomtilly relled fter power off, when turning the power on gin. This Mnul is pplile to Revised April 2nd 2015 Pg 4.
1st MENU Displyed (srolling with the nd the uttons) 2nd MENU Displyed (fter pressing the X tht stnds for ENTER) Explntion of Eh MENU FUNTION TEMPERATURE This funtion Displys in rel time the LED ARRAY se temperture in. When pressing Enter gin you exit from the temperture disply. The stedy stte TEMPERATURE of the ARRAY rehes pprox. 55 fter mny hours of ontinuous opertion with n mient temperture of 25-30. The Therml Hndling of the LED is Automtilly hndled y the lol eletronis nd the LED will operte until the ARRAY temperture rehes 80, tht nywy is still wy within the presried mximum nominl presried y the ARRAY mnufturer tht is 105. In se the ARRAY temperture rehes 80 the unit will utomtilly turn off. Even in extreme Amient temperture onditions the LED ARRAY shll never reh the 80 limit. The ove protetion threshold is there to protet the LED ARRAY from stressed working onditions in se some other filures or speilly ritil working onditions re using n over-temperture. HANNEL SETTING (RESOLUTION & FUNTION) This Funtion is to set the DIMMING RESOLUTION either t 8 its or t 16 its. One HAN is displyed, t on the or uttons to sroll through the following hoises: 8D: 8 its resolution (the disply will show 8D nd this is the defult setting). The Fixture utilises 1 DMX iruit for the Light Dimming, whih is the BASE IRUIT set in the ADDRESS. 8DS: NOT ATIVE (for future use): The foreseen funtion for this setting is: 8 its resolution nd STROBE (the disply will show 8DS). The Fixture will utilise 2 DMX iruits, the BASE IRUIT set in the ADDRESS will e the LIGHT DIMMING nd the seond iruit (BASE +1) will e the STROBE 16D: 16 its resolution (the disply will show 16D). The Fixture utilises 2 DMX iruits, the BASE IRUIT set in the ADDRESS is the orse Dimming, the seond iruit (BASE +1) is the Fine Dimming. 16DS: NOT ATIVE (for future use): The foreseen funtion for this setting is: 16 its resolution nd STROBE (the disply will show 16DS). The Fixture will utilise 3 DMX iruits, the BASE IRUIT set in the ADDRESS will e the orse Dimming, the seond iruit (BASE + 1) will e the Fine Dimming. the third IRUIT (BASE + 2) will e the STROBE Of ourse the 16 its funtion is useful if the orresponding iruits on the DMX LIGHTING BOARD re lso set t 16 its. WARNING: if the LED FRESNEL is set t 16 its, ut more units re hving onseutive unitry ddress (for instne first fixture set t Address 1, seond fixture set t Address 2 nd so forth, the DMX hnnel ontrolling the orse Dimming of the seond unit, will lso ontrol the fine dimming of the first unit. In this se it is reommended tht ll fixtures re set to 8 its resolution). DMX LEVEL It Shows the DMX Input level on perentge (0-99% nd FULL) reeived effetively from the Fixture. Press ENTER to exit this MENU. 7. HARATERISTIS AND PERFORMANE DATA DESRIPTION VALUE DESRIPTION VALUE LED Power 165 W Protetion Type IP 22 Power 190W @ 230 V Mx Housing temperture 70 onsumption 205W @ 120 V DMX Dt link USITT DMX512-A DMX hnnels: Protetion lss This produt uses 5-pin XLR for DMX input nd output. Use shielded dt les. Do not overlod the disy hin. Up to mximum of 32 devies n e used on single DMX hin. Speifitions sujet to hnge without notie. 1 t 8it: Dimmer 2 t 16it: Dimmer lss 1 ground onnetion required Weight of Fixture Weight of rndoor M.O. P.O. 13,5 kg. 14,8 kg. 4 lef 8 lef 1,4 kg. 1,65 kg. Weight of olor frme 0,6 kg. Size of srims & olor frme Size of Brndoor ring Set Dimeter A.ies Dimeter 306 mm. 305 mm ( 12 ) Set Dimeter Ring Dimeter 314 mm. 313 mm.( 12 1/4 ) Lens dimeter 250 mm. This Mnul is pplile to Revised April 2nd 2015 Pg 5.
8. DIMENSIONS Dimensions: Blk=mm. Red=inhes Dimensions: Blk=mm. Red=inhes 9. PERIODI INSPETION & MAINTENANE This produt requires very little routine mintenne, if ny, ut hs speil lening instrutions: Disonnet fixture from power nd llow it to ool for 10 min. 1. Vuum or gently low wy ny dust from fn ldes nd grills 2. Very gently len the LED with Isopropyl lohol. 3. len the lenses with soft dmp loth. 4. hek the ondition of the sfety shield (see hpter: Instlltion Instrutions) efore every use. 5. hek Power supply le nd DMX ontrol le proper onditions 10. SAFETY STANDARDS Europe: The produt onforms the Applile Europen Diretives & Stndrds Low Voltge Diretive: 73/23/EE (s mended y 93/68/EE) EM Diretive: 89/336/EE (s mended y 92/31/EE & y 93/68/EE) Europen Stndrds:: EN 60598-2-17, EN 60598-1, EN 55015, EN 61547 Disposing of this produt: Help preserve the environment! Ensure tht this produt is reyled t the end of its life. This produt is in ompline with the RoHS nd WEEE diretives. This Mnul is pplile to Revised April 2nd 2015 Pg 6.
This Mnul is pplile to Revised April 2nd 2015 Pg 7. A A m B d d f i h g SEE SHEET 2 e e p p o n r s s q
This Mnul is pplile to Revised April 2nd 2015 Pg 8. m B d d f i h g SEE SHEET 2 e e p p o n r s s q z z A A