Technical nformation General escription proportional directional control valves are direct operated solenoid valves with electronic spool position feedback, and on-board integrated control electronics. *FX valves are user configurable to proportionally control flow in response to voltage or current command signals. Valves are available in sizes NG6 (TOP 3) and NG1 (TOP 5). Three electronic control options are available simplifying user application. onfigurations include the industrial standard 7-pin interface, or options for a user configurable simple proportional analog outer closed loop, or ± 1V reference outputs which can be used as user command voltage references. *FX valve performance is characterized by high resolution flow control, repeatability, and good dynamic performance. Typical applications include precise and reproducible control of actuator speed in rapid/slow speed profiling, and smooth acceleration and deceleration performance. Features ntegrated valve electronics. Versatile electronic control options. Spool position feedback. Spring centered spool. Manual override. Progressive flow characteristics for high resolution flow rate adjustment for small commands. L functional diagnostics. Specifications nterface N (NFP/SO/TOP) NG6 (3) NG1 (5) Rating @1 ar (15 PS) Δp (P, T) (spool options up to) 1) LPM (GPM) 2 (5.3) 6 (15.9) Maximum LPM (GPM) 47 (12.5) 17 (45) Step Response (time to reach 9% of a 1% step command) ms 6 75 Hysteresis % <1.5 Repeatability % <.5 Max. Operating Pressure Port P,, ar (PS) 315 (45) Port T 35 (5) Fluid leanliness Level SO lass 18/16/13 Fluid Viscosity, Recommended 75 6 SS Fluid Temperature, to +6 Recommended (+32 F to +14 F) mbient Operating -2 to +6 Temperature (-2 F to +14 F) lectrical Power Requirements 24V Version J : NG6 (3) 18 to 3 V, 3 24V Version J : NG1 (5) 18 to 3 V, 4 12V Version K : NG6 (3) only 11.5 to 15 V, 4 ommand Signal (impedance) (select by ordering code) 24V Version J 12V Version K ommand Polarity ± 1 V (1K ohm) ± 2 m (499 ohm) ± 5 V (1K ohm) ± 2 m (249 ohm) Pin more positive than ; P to Spool Position Monitor 24V Version J ± 1 V 12V Version K ± 5 V Mating onnector 7-Pin for lectronic esign Part #5472 6-Pin for lectronic esign & Part #697561 nvironmental Protection lass NM 4 (P65) 1) ctual pressure drop required for each metering land, up to the specified maximum flow rate is: Q ΔP actual actual = (5)( Q rated ) 2 ar; (Q in LPM) Q [or] = (75)( actual Q rated ) 2 PS; (Q in GPM) 3 lyria, Ohio, S
Ordering nformation *FX Proportional irectional ontrol Valve with Spool Position Feedback and ntegrated lectronics Spool Type Style Seal lectronic Supply lectronic esign Voltage ccessories Valve ccessories esign Series NOT: Not required when ordering. Nominal Size escription 1FX NG6/TOP 3 3FX NG1/TOP 5 J 24 V K 12 V* * vailable only with 1FX lectronic esign s &. Q =Q Q >Q * Q >Q ** Spool Type 1 31 31 2 32 32 escription* Standard ompliant On-board onfigurable Outer losed Loop On-board ±1V Reference Voltages *ll designs are user configurable to voltage or current command. 85*** * Reduced flow rate on port. ** Reduced flow rate on port. *** 5% lap spool for special applications. onsult Factory; 1FX: code F, style only. 3FX: code M, style only. escription N Nitrile V Fluorocarbon Note: NG1 (TOP5) valves are supplied with bolt kit K98 (1/4 2 x 1.625). For metric bolt kit K385 (M6 x 4 mm), add -X6181 to ordering code. at Δp 5 ar (72.5 PS) per metering edge 1FX 3FX LPM (GPM) LPM (GPM) Style Weight: NG6 NG1 3.4 kg (7.5 lbs.) 8.3 kg (18.3 lbs.) 7.5 (2)* F 15 (4) H 2 (5.3)* 2 (5.3)* K** 3 (7.9) M 4 (1.6) S 6 (15.9)* * Spool type only. ** Spool type 1 only. K Mounting nterface Refer to Mounting nterface imensions in the Proportional irectional Valve section of this catalog. ccessories Refer to the ccessories section for bolt kits, subplates, connectors and pre-assembled cable assemblies. 31 lyria, Ohio, S
ntegrated Valve lectronics pplication Guidelines *FX proportional valves are available in three control configurations. Option conforms to the industrial proportional valve standard and is interchangeable with most competitors valves of this type. Options and are designed to simplify user application by providing specific features. Note that the control option uses the industrial standard compliant 7-pin MS connector while options and use a 6-pin MS conenctor. Refer to the table below for connector pinout assignments. Specifications lectronic esign Option - - - Function onnector Pin ssignment Power Supply +V V Reference +1V Outputs -1V F F nable ommand +M -M Spool Position Monitor F Outer Loop Feedback user Protective Ground G nternal djustment Refer to the nstallation Guide for set-up, configuration, and application guidelines (packaged with each valve). 1FX: nstallation ulletin 2583-M1/S 3FX: nstallation ulletin 2587-M1/S Min. Min. Max. Max. Test Points 1: Spool P 2: dj. M 3: ommon Red L P Green L P Null Gain ias Factory Set onfiguration Jumpers (1-5) alibration Switch esign Option ndustrial Standard 7-Pin MS onnector nterface lectronic design option implements the industrial standard 7-pin MS connector interface. The design provides a differential command input that is user configurable as voltage or current, an external valve enable feature, and a spool position monitor output. To specify this option, refer to the Ordering nformation page, lectronic esign block. nable Voltage or urrent input (Note 1) 5...3V + M - M JP1 ias MX MN Spool Position Monitor (Note 2) Protective arth Supply Voltage (Note 2) +V V F G Green P Red P Note 1: nstall jumper JP1 for current command input. Refer to nstallation ulletin 2583-M1/S (1FX). Note 2: Refer to specifications. S 32 lyria, Ohio, S
ntegrated Valve lectronics esign Option ser onfigurable nalog Outer losed Loop lectronic design option provides an additional analog closed outer loop function for user application. This feature can be used to control simple position control loops where analog resolution and a single proportional gain control are adequate. The design provides a single bipolar command input that is user configurable as voltage or current, and an outer loop feedback sensor voltage input. ±1 volt outputs are available to reference the outer loop feedback sensor if required. To specify this option, refer to the Ordering nformation page, lectronic esign block. ias Voltage nput urrent nput (Note 1)...±1V...±2m JP1 + MX MN JP5 Outer Loop Feedback nput Supply Voltage Reference Voltage Outputs...±1V +24V V +1V -1V F JP4 nvert (Note 2) TP1 Monitor Green P P Gain Red P S Note 1: nstall jumper JP1 for current command input. Refer to nstallation ulletin 2583-M1/S (1FX). Note 2: nstall jumper JP4 to invert user outer loop feedback input signal. esign Option Single ipolar ommand nput, with ± Volt Reference Output lectronic design option provides a single bipolar command input that is user configurable as voltage or current. ±1 volt references are available for user supplied off-board command potentiometers. spool position monitor output is also provided. To specify this option, refer to the Ordering nformation page, lectronic esign block. Voltage nput urrent nput (Note 1)...±1V...±2m JP1 MX MN ias Spool Position Monitor (Note 3) S Supply Voltage Reference Voltage Outputs +24V V +1V -1V F Green P Red P Note 1: nstall jumper JP1 for current command input. Refer to nstallation ulletin 2583-M1/S (1FX). Note 2: nstall jumper JP4 to invert user outer loop feedback input signal. Note 3: Refer to specifications. 33 lyria, Ohio, S
Performance urves 5.3 2 1FX haracteristics at p = 5 ar (72.5 PS) / metering edge P : T; or P : T 15.9 6 3FX haracteristics at p = 5 ar (72.5 PS) / metering edge P : T; or P : T 4. 15 2.6 1 H F 13.2 5 1.6 4 7.9 3 5.3 2 S M H 1.3 5 2.6 1 2 4 6 8 1 2 4 6 8 1 ommand Signal (%) ommand Signal (%) 14 53 12 1 8 6 4 2 45 38 3 23 15 8 ar PS F 1FX Operating Limits 1) 3FX Operating Limits 1) at 1% ommand at 1% ommand P : T; or P : T P : T; or P : T 69 1 H 138 27 2 3 Pressure rop 276 4 5 189 45 17 4 151 35 3 114 25 95 2 76 15 1 5 133 57 38 19 ar PS 69 1 H S M 138 27 2 3 Pressure rop 276 4 1) Shaded area: ctual flow subject to the system load dynamics Note: 81 and 82 spools - decrease limits by 15% 1FX Frequency Response at 1% ommand, 5% Offset 3FX Frequency Response at 1% ommand, 5% Offset mplitude Ratio (d) -3-1 1 2 3 4 ± 1% ± 1% 5 6 8 1 2 3 4 56 Frequency (Hz) 135 9 45 Phase Shift ( ) mplitude Ratio (d) -3-1 1 2 3 4 ± 1% ± 1% 5 6 8 1 2 3 4 56 Frequency (Hz) 135 9 45 Phase Shift ( ) 34 lyria, Ohio, S
imensions 1FX nch equivalents for millimeter dimensions are shown in (**) 49.6 (1.95) 32. (12.6) 25. (9.84) 13. (5.12) P 22.5 (.89) 24. (.94) Manual overrides both sides ca. 17. (6.69) 3FX nch equivalents for millimeter dimensions are shown in (**) 361. (14.21) 31. (12.2) 156. (6.14) 97. (3.82) 97. (3.82) 36. (1.42) P 7. (2.76) Manual overrides both sides 3. (1.18) ca. 212. (8.35) 35 lyria, Ohio, S