Extended delay of broadband signals in stimulated Brillouin scattering slow light using synthesized pump chirp

Extended delay of broadband signals in stimulated Brillouin scattering slow light using synthesized pump chirp Avi Zadok, Avishay Eyal and Moshe Tur Faculty of Engineering, Tel-Aviv University, Tel-Aviv 69978 Israel. avinoamz@post.tau.ac.il Abstract: Judicious chirping of a directly modulated pump laser is used to broaden the intrinsic linewidth of stimulated Brillouin scattering in an optical fiber. The modulation waveform is designed to obtain a spectrum with sharp edges, resulting in phase gradients stronger that those obtained for random pump modulation. The gain and phase frequency response of the slow light process are measured by a vector network analyzer, and the delays obtained for our tailored modulation are compared with the case of random direct modulation. For equal pump powers and gain bandwidths (FWHM), the tailored modulation waveform introduces 3-4% longer delays. Using this technique, pseudo random bit sequences of 5 Gb/s were successfully delayed by up to 2 ps (BER< -5 ) and 8 ps (BER< -9 ). 26 Optical Society of America OCIS codes: (6.437) Non-linear optics, fibers; (29.59) Scattering, stimulated Brillouin; (35.55) Propagation; (999.9999) Slow light. References and links. R. W. Boyd, and D. J. Gauthier, Slow and fast light, in Progress in Optics, E. Wolf, ed. (Elsevier, Amsterdam, 22), Vol. 43 pp. 497-53. 2. R. S. Tucker, P.-C. Ku, and C. J. Chang-Hasnain, Slow-light optical buffers: capabilities and fundamental limitations, J. Lightwave Technol. 23, 446-466 (25). 3. M. D. Stenner, M. A. Neifeld, Z. Zhu, A. M. C. Dawes, and D. J. Gauthier, Distortion management in slowlight pulse delay, Opt. Express 3 9995-2 (25). 4. L. V. Hau, S. E. Harris, Z. Dutton, and C. H. Behroozi, Light speed reduction to 7 meters per second in an ultracold atomic gas, Nature 397, 594-598 (999). 5. C. Liu, Z. Dutton, C. Behroozi, and L. V. Hau, Observation of coherent optical information storage in an atomic medium using halted light pulses, Nature 49, 49-493 (2). 6. M. D. Stenner, D. J. Gauthier, and M. A. Neifeld, The speed of information in a 'fast-light' optical medium, Nature 425, 695-698 (23). 7. P. C. Ku, F. Sedgwich, C. Chang-Hasnain, P. Palinginis, T. Li, H. Wang, S. W. Chang, and S. L. Chuang, Slow light in semiconductor quantum wells, Opt. Lett. 29 229-2293 (24). 8. H. Gersen, T. J. Karle, R. J. Emjelen, W. Bogaerts, J. P. Korterik, N. F. van Hulst, T. F. Krauss, and L. Kuipers, Real-space observation of ultraslow light in photonic crystal waveguides, Phys. Rev. Lett.. 94, 7393 (25). 9. Y. Okawachi, M. S. Bigelow, J. Sharping, Z. Zhu, A. Shweinsberg, D. J. Gauthier, R. W. Boyd, and A. Gaeta, Tunable all-optical delays via Brillouin slow light in an optical fiber, Phys. Rev. Lett. 94, 5392 (25).. M. González-Herráez, K.-Y. Song, and L. Thévenaz, Optically controlled slow and fast light in optical fibers using stimulated Brillouin scattering, Appl. Phys. Lett. 87, 83 (25).. K.-Y. Song, M. González-Herráez, and L. Thévenaz, Long optically controlled delays in optical fibers, Opt. Lett. 3, 782-784 (25). 2. J. E. Sharping, Y. Okawachi, and A. L. Gaeta, Wide bandwidth slow light using a Raman fiber amplifier, Opt. Express 3, 692-698 (25). 3. D. Dahan, and G. Eisenstein, Tunable all optical delay via slow and fast light propagation in Raman assisted fiber optical parametric amplifier: a route to all optical buffering, Opt. Express 3 6234-6249 (25). 4. J. E. Sharping, Y. Okawachi, J. van Howe, C. Xu, and A. Gaeta, All-optical tunable, nanosecond delay using wavelength conversion and fiber dispersion, in proceedings of CLEO 25, Long Beach, Ca, 25, paper CTuT. (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 8498

5. C. Yu, T. Luo, L. Zhang, and A. E. Willner, Distortion effects on data pulses in a slow light tunable delay line due to stimulated Brillouin scattering in a highly nonlinear fiber, in proceedings of ECOC 25, Glasgow, UK, 26, paper Mo 4.5.2. 6. M. González-Herráez, K.-Y. Song, and L. Thévenaz, Arbitrary-bandwidth Brillouin slow light in optical fibers, Opt. Express 4, 395-4 (26). 7. E. Shumakher, N.Orbach, A. Nevet, D. Dahan, and G. Eisenstein, On the balance between delay, bandwidth and signal distortion in slow light systems based on stimulated Brillouin scattering in optical fibers, Opt. Express 4, 5877-5884 (26). 8. A. Minardo, R. Bernini, and L. Zeni, Low distortion Brillouin slow light in optical fibers using AM modulation, Opt. Express 4, 5866-5876 (26). 9. Z. Zhu, A. M. C. Dawes, D. J. Gauthier, L. Zhang, and A. E. Willner, 2-GHz-Bandwidth SBS slow light in optical fibers, in proceedings of OFC/NFOES 26, Anaheim, Ca, 26, paper PDP. 2. B. W. Hakki, Evaluation of transmission characteristics of chirped DFB lasers in dispersive optical fiber, J. Lightwave Technol., 964-97 (992) 2. R. W. Boyd, D. J. Gauthier, A. L. Gaeta, and A. E. Willner, Maximum time delay achievable on propagation through a slow light medium, Phys. Rev. A. 7, 238 (25). 22. J. B. Khurgin, Performance limits of delay lines based on optical amplifiers, Opt. Lett. 3, 948-95 (26). 23. H. Shalom, A. Zadok, M. Tur, W. D. Cornwell and I. Andonovich, On the Various Time Constants of Wavelength Changes of a DFB Laser under Direct Modulation, IEEE J. Quantum Electron. 34,86-824 (998). 24. A. Zadok, H. Shalom, M. Tur, W.D. Cornwell, and I. Andonovich, Spectral Shift and Broadening of DFB Lasers under Direct Modulation, IEEE Photon. Technol. Lett.,, 79-7 (998). 25. M. Ito, and T. Kimura, Stationary and transient thermal properties of semiconductor laser diode, IEEE J. Quantum Electron. 7, 787-795 (98). 26. G. P. Agrawal, and N. K. Dutta, Long-Wavelength Semiconductor Lasers, (Van Nostrand, New York, NY, 986). 27. A. Loayssa, D. Benito, and M. J. Grade, High resolution measurement of stimulated Brillouin scattering spectra in single-mode fibers, IEE Proc. Optoelectron. 48, 43-48 (2).. Introduction Tunable optical delays, based on the ability to control the group velocity of signals propagating through an optical medium, have been at the focus of extensive research recently. Such tunable delays should prove important for applications such as clock alignment of optical communication signals, optical signal processing and microwave photonics [-3]. Controllable delays may be achieved in the vicinity of gain or absorption peaks, introduced by a variety of non-linear mechanisms [, 2], which are accompanied by large spectral gradients of the optical phase. These phase delay gradients modify the group velocity, which can be made slower than that of the linear medium [4, 5], and in some cases even faster [6]. These conditions are often referred to as "slow light" and "fast light", respectively. The group velocity of light was reduced by orders of magnitude using electromagnetically-induced transparency in cold atomic gas [4, 5], population oscillations in quantum well material [7], and photonic crystal structures [8]. Realizations of slow and fast light in optical fibers, operating at room temperature, are particularly attractive for optical communication and signal processing applications. Numerous physical mechanisms have been successfully utilized, including Stimulated Brillouin Scattering (SBS) [3, 9-], Raman scattering [2], Raman-assisted parametric amplification [3] and a combination of four-wave mixing and dispersion [4]. For narrowband signals, SBS offers relatively long delays, robustness, implementation simplicity, and relatively low threshold power in standard fibers. However, most applications of slow-light-based time delays would require a usable bandwidth of several GHz, compatible with the data rates of current optical communication systems. While early demonstrations of SBS-induced slow light used a continuous wave (CW) pump laser to obtain only 3MHz-wide SBS gain curve [3, 9-, 5], recently this spectral width was successfully broadened through modulation of the pump laser [3, 6-8], culminating in the delay of a single 75ps pulse by 47 ps [9]. The pump modulation can be either external [3, 7, 8], or direct [6, 9], where a relatively narrowband amplitude modulation of the injection current gives rise to frequency chirp in the laser output [2]. The (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 8499

increased bandwidth is achieved at the expense of a higher pump power and reduced delay [2, 22]. In addition, when the signal bandwidth approaches the spectral width of the SBS process gain curve, considerable distortion and pattern dependence may occur [5, 7, 9]. With available pump power often limited, careful trade-offs among delay, bandwidth and signal fidelity are essential [5, 7, 22]. Previously reported schemes for broadband SBS slow light had relied on stochastic direct modulation of the pump signal, using either a noise source [9], or a Pseudo-Random Bit Sequence (PRBS) [6]. Although a large bandwidth has been achieved, it is tempting to examine the role played by the waveform of the modulating pump current on the SBS process. It was previously shown theoretically that a judicious choice of the spectral line shape of the SBS gain could lead to better performance [22]. In this paper, we use both current-induced and thermally-induced chirp, [23, 24], to tailor the optical pump spectrum of a semiconductor laser using a combination of a deterministic, periodic current modulation together with a small random component. The optical spectrum of the pump laser is synthesized to a specific shape, using a previously established model of chirp dynamics [23, 24]. Adjustment of the modulating waveform provides extra degrees of freedom for control of the gain and phase response of the SBS process. The gain and phase response of broadband SBS are measured experimentally, using different pump modulation parameters. We show that when compared with random noise pump modulation, a properly chosen periodic waveform increases the group delay by 3-4%, for the same pump power and gain bandwidth. The broadened SBS process was successfully applied in delaying 27 ps wide isolated pulses and 5 Gb/s Non- Return to Zero (NRZ) patterns. Using this novel technique, PRBS data of 5 Gb/s were successfully delayed by up to 2 ps with a BER< -5, a result we could not obtain using random pump modulation of equal bandwidth and optical power. The rest of this paper is organized as follows: Section 2 briefly describes the chirp dynamics of a Distributed Feed-Back (DFB) laser, and the synthesis of the optical spectrum of the modulated pump laser. Measurements of the gain and phase response of broadband SBS are reported in Section 3, and the corresponding delay of pulses and PRBS signals is detailed in Section 4. Finally, a discussion of the results and future work is given in Section 5. 2. Optical spectrum of directly modulated DFB lasers. Direct modulation of the injection current of a DFB laser affects its instantaneous optical frequency through three separate mechanisms: transient, adiabatic and thermal chirp [2, 25]. Transient chirp is associated with the mutual feedback of photon and carrier densities, following a step transition of the current [26]. The typical time constants are of the order of ps, so that transient chirp may be neglected for direct modulation at MHz rates, to be used below. Adiabatic chirp describes the frequency variations introduced by the current-related changes of the equilibrium carrier density. The adiabatic chirp contribution immediately follows the instantaneous injection current, with a magnitude in the range of.- GHz/mA [2, 23]. Thermal chirp is proportional to the instantaneous temperature of the laser active region, which modifies both its refractive index and physical length [25]. The thermal chirp is slower to evolve, and its dynamics are determined by the thermal conductivity and capacitance of the various structural layers. In a previous study [23, 24], a simplified, semiempirical model for the thermal effect of the modulating current i(t) on the instantaneous optical frequency ν (t) was established through a convolution integral, in which its impulse response is characterized by a weighted series of time constants τ n, n = {...N} : N () t = ν( t) = i( t) h( t); h Δν n exp t () τn These time constants correspond to the thermal properties of different layers, and they range from tens of ns to several ms [25]. With prior knowledge of the adiabatic and thermal chirp parameters, the instantaneous optical frequency of a DFB laser subjected to arbitrary direct modulation can be determined, and the optical spectrum may be synthesized [24]. n= (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 85

The search for a 'more slowing' modulation waveform is motivated by the observation that an SBS gain curve with steep edges will give rise to longer delays. This observation can be demonstrated using the Kramers-Kronig relations [9, 22]: [ g( ω' )/ 2] 2 Re Im[ ( ω) / 2] = ω' 2 2 π g d (2) ω' ω where g ( ω) is the complex gain function of the SBS process [3, 9]. Let us compare between two shapes of Re [ g( ω) ], shown schematically in Fig. (a). Since the actual power gain seen by the signal to be delayed (the probe signal) depends exponentially on Re [ g( ω) ], the two spectral shapes will result in similar bandwidths. However, the corresponding phase response curves, depicted in Fig. (b), show significant differences. It is the nature of the integral relation of Eq. (2) that transforms the abrupt edges of the dashed curve into the larger frequency gradient of the phase response, resulting in a longer delay. Previous works [6, 9] have related the SBS complex gain function to a convolution of the pump spectrum and the 3 MHz-wide natural Lorentian of the SBS process. Therefore, a pump spectrum synthesized to have sharp edges would produce a complex SBS gain function with longer delays. a: b: Relative gain.9.8.7.6.5.4.3 Phase response [arb.].5.5 -.5.2. -3-2 - 2 3 Normalized frequency offset Fig.. (a): Gaussian and truncated Gaussian spectral gain curves Re [ g( ω) ] spectral phase responses Im [ g( ω) ] - -.5-3 -2-2 3 Normalized frequency offset, calculated using the Kramers-Kronig relations.. (b): Corresponding Following the discussion of the last paragraph and using our model for the laser chirp, we found that a periodic modulation waveform of the form:.5 t mod T i () t = i + Δi, (3) T with a period T = 32ns and magnitude Δi = 24mA would give rise to a broadened pump spectrum of the required shape (64 samples were chosen for each period, which for our 2 MSamples/s arbitrary waveform generator resulted in a period of T=32ns. Longer periods did not affect the results). The laser bias current i was 8mA. Figure 2(a) shows the simulated result together with a measured spectrum. This spectral measurement was performed by beating the modulated laser with a CW laser on a photodiode, whose output fed a Radio Frequency (RF) spectrum analyzer [6]. The measured optical spectrum is in good agreement with the simulated predictions, and the design objective of sharp spectral transitions is met, albeit with sizable fast transients. Smoothing of these disturbing spectral featured was achieved by adding a random modulation component of Gaussian statistics. The measured optical spectrum is shown in the dashed line of Fig. 2(b). Also shown is the spectrum for entirely random modulation (solid), with a bandwidth of 2 MHz and RMS magnitude of (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 85

2mA. Both modulation schemes of Fig. 2(b) were alternately used to drive the pump laser in the broadband SBS slow light experimental setup, to be described next. a: b: 5-2 Relative power spectral density [db] -5 - -5 Optical power [dbm] -25-3 -35-4 -2-6 -4-2 2 4 6-45 - -5 5 Fig. 2. (a): Dashed line: simulated optical spectrum of DFB laser periodically modulated by the waveform of Eq. (3) with the following parameters: adiabatic chirp coefficient.33 GHz/mA, τ,2 = 2, 2 ns and Δν,2 =.5,.48 GHz/mA [22]; Solid line: corresponding measured spectrum. (b): Dashed line: measured optical spectrum for a directly modulated DFB laser, using the waveform of Eq. (3) together with a 2 MHz random component of 2mA (rms); Solid line: measured optical spectrum for a directly modulated DFB laser, using 2 MHz random modulation of 2mA (rms). 3. Gain and phase response of SBS with directly modulated pump Figure 3 shows the setup for characterizing the optical gain and phase response of the SBS process. The laser of the previous section was used to generate the pump signal. The pump laser signal was directly modulated by the output voltage of an arbitrary waveform generator, and amplified by a high power optical amplifier. A circulator directed the pump signal into 2 km of Dispersion Shifted Fiber (DSF), which was used as the SBS non-linear medium. A stable tunable laser was used as a probe signal source, and a polarization controller adjusted the state of polarization of the probe signal for maximum interaction [9, 27]. The probe laser was connected to a Single Side-Band (SSB) LiNbO 3 Mach-Zehnder modulator. Using a Vector Network Analyzer (VNA), the upshifted modulation sideband scanned the broadened SBS gain curve over a 2-5GHz range, while the frequency of the probe laser was tuned to fall below this curve. The VNA detected the beating signal of the carrier and sideband, and its magnitude and phase as a function of frequency with the pump turned off were taken as reference values. The changes to the beating signal with the pump laser turned on are, therefore, proportional to the complex response of the SBS process [7, 27]. Fig. 3. Setup for the measurements of the SBS slow light gain and phase response. BPF: band pass filter. EDFA: Erbium-doped fiber amplifier. (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 852

Examples of the SBS power gain curves obtained for synthesized and random direct pump modulation are shown in Fig. 4(a-b), using pump power levels of 9-22 dbm. The Full Width at Half Maximum (FWHM) of the gain curves are approximately 3 GHz for both modulation formats. The corresponding phase response curves are displayed in Fig. 4(c-d). As anticipated, the steep spectral transitions of the gain curve observed for the tailored modulation are accompanied by stronger gradients of the phase response. The response also shows a phase delay offset, which does not affect the group delay. The calculated group delays τ, determined by the slope of a linear fit to the phase response within the FWHM of the gain curve, are shown in Fig. 5 as a function of the maximum SBS power gain. For equal maximum gain of the probe signal, the calculated group delay obtained with synthesized modulation is 3-4% longer. a: b: 2 2 8 8 Probe signal power gain [db] 6 4 2 8 6 4 Probe signal power gain [db] 6 4 2 8 6 4 2 2 c: -4-2 2 4 6 d: -4-2 2 4 6 3 3 Probe signal phase response [rad] 2 - -2 Probe signal phase response [rad] 2 - -2-3 -6-4 -2 2 4 6-3 -6-4 -2 2 4 6 Fig. 4. Measured gain curves of SBS using synthesized (a) and random (b) direct pump modulation. The pump power levels are (top to bottom): 22 dbm, 2 dbm, 2 dbm, 9 dbm. Measured phase response curves of SBS using synthesized (c) and random (d) direct pump modulation. The pump power levels are: 22 dbm (blue), 2 dbm (green), 2 dbm (red). 2 Calculated group delay [ps] 8 6 4 2 8 2 4 6 8 2 Maximum SBS gain [db] Fig. 5. Calculated group delays as a function of maximum SBS power gain, using synthesized (asterisk signs) and random (plus signs) direct pump modulation. (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 853

4. Delay of broadband pulses and PRBS data. The broadened SBS process was used to delay short pulses and high rate PRBS signals. The output of the probe tunable laser was connected to a LiNbO 3 Mach-Zehnder modulator, driven by a PRBS generator. The delayed, amplified signal at the DSF output was detected by a sampling oscilloscope. In the first set of measurements, isolated pulses with a FWHM of 27 ps were used. Figure 6(a) shows the normalized output pulses for synthesized pump modulation and pump power levels of 8 and 22 dbm, alongside the original pulse. Also shown are the calculated output pulses, based on the gain and phase response measured by the VNA. The delay and broadening of the pulses are well accounted for by the complex SBS response [7], with some differences at the tails of the pulse for 22 dbm pump power. In the second part of the experiment, the probe pulses were replaced by 5 Gb/s, 2 3 - long NRZ PRBS. The output eye diagrams were observed, and the signal gain and delay were measured for both pump modulation formats and different pump power levels. Figure 6(b) shows the measured delay as a function of probe signal gain. The delays observed for synthesized modulation are longer by 3-4%, in agreement with the SBS phase response measurements of the previous section. a: b: Normalized output power.9.8.7.6.5.4.3.2. 2 4 6 8 Time [ps] Measured PRBS delay [ps] 4 2 8 6 4 2 6 7 8 9 2 3 PRBS signal power gain [db] Fig. 6. (a): SBS induced delays of 27 ps pulses using synthesized pump modulation. Solid lines, left to right: input pulse, output pulse for pump power of 8 dbm, output pulse for pump power of 22 dbm. Dashed lines: calculated output pulses for pump power of 8 dbm (left) and 22 dbm (right). (b): Measured delays of 5 Gb/s NRZ PRBS as a function of power gain, using synthesized (asterisk signs) and random (plus signs) direct modulations. An example of the output eye diagram, delayed by 2 ps using synthesized pump modulation, is given in Fig. 7. The BER for delays of 8, and 2 ps using synthesized modulation were < -9, -8 and 4-6, respectively. The product of error free delay and bit rate was.4, achieved with pump power of 2 dbm. This is a novel demonstration of high bit rate, error free SBS-induced delay. Fig. 7. Output eye diagram of a 5 Gb/s NRZ PRBS, delayed by 2 ps using SBS with synthesized, direct pump modulation. (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 854

5. Summary In summary, the delay obtained in broadband SBS slow light in fiber was extended using direct modulation of the pump laser with pre-designed chirp. Manipulating the modulation waveform provides extra degrees of freedom for adjustment of the SBS gain and phase response. The chosen modulation waveform generates a tailored pump spectrum with sharp spectral edges, leading to stronger gradients in the SBS phase response. A delay extension of 3-4% was observed, when the novel, synthesized modulation had replaced random direct modulation of equal FWHM bandwidth and pump power. Using this novel technique, PRBS data of 5 Gb/s were successfully delayed by up to 2 ps with a BER< -5. While the obtained extended delay is still only a fraction of a bit period, it may prove useful in data synchronization and microwave photonics. A more comprehensive study is under way to theoretically evaluate the relation between the spectrum of a broadband, non-stationary pump and the optical phase response of the probe signal, including pump depletion, aiming at optimizing the modulation waveform. Acknowledgement The authors wish to thank G. Eisenstein and E. Shumakher of the Technion, Haifa, Israel, for sharing their advice and experience. Avi Zadok acknowledges the support of the Israeli Clore Foundation for his Ph.D. studies scholarship. The research was supported in part by the Israeli Science Foundation. (C) 26 OSA 8 September 26 / Vol. 4, No. 9 / OPTICS EXPRESS 855