N onnectors General Description Delta N connectors are compact, economical, 50Ω impedance connectors with two-stud bayonet coupling. They are best suited for use with cables in the range of.150" to.50" diameter, but are available for other cables from.090" to over.75" diameter. M3901 QPL N connectors and M55339 QPL N adapters are also included in this section. Our extensive line ou may need to complete your system design. dapters between N and other series are shown starting page 176. s with our other connector series, Delta s customer-driven design results in N series connectors with practical and unique features that make your design and assembly process easier. Some of these include: Heli-Grip cable connectors for fast, reliable assembly to flexible cable without special tooling. PressMount receptacles (page 7) mount securely in a single round hole, saving space on your components and reducing your housing fabrication costs. Panel receptacles with flange sizes to match the same hole pattern as standard SM or type N connectors, letting you drill one hole pattern and mount N, N, SM, TN, or 7/16 series connectors as needed. Isolated ground receptacles (see page 5). 75 Ω impedance N connectors (see page 31) for matched-impedance applications. Our N series product line is still growing, so please call if you don t see what you need. N onfigurations Straight Plugs... Right ngle Plugs...4 Straight Jacks...6 ulkhead Jacks...7 Panel Jacks...9 Panel Jack Receptacles (square flange)...11 Right ngle Panel Jack Receptacles...1 Panel Plug Receptacles...1 ulkhead Jack Receptacles...13 ulkhead Plug Receptacles...14 Printed-ircuit oard Receptacles...15 Stripline Receptacles...15 PressMount Receptacles...16 Resistive Terminations...17 Dust aps...17 In-Series dapters...18 N Specifications*.081.087.3 max. 179 181.08.8.10.30 Jack Interface**.378.38.43.436 Reference Plane.006 min..190 min..319.31.003 min..37.333.56 max. *See below.385.390 179 181 meet gage requirements of MIL-PRF-3901/16..346.356.188.08.186 max..015.030.075.081.04.08 Plug Interface**.414 min..37.335 **Some proportions altered to illustrate detail..091.097 Reference Plane.186.06.081.087.006 max..463.473 Electrical: Nominal Impedance: 50 ohms. Frequency Range: D 4 GHz. Voltage Rating: 500 volts RMS. Dielectric Withstanding Voltage: 1,500 VRMS. Insulation Resistance: 5,000 megohms. Materials/Finishes: Insulators: Teflon per STM D1710. Male ontacts: rass per STM 16. Female ontacts: eryllium opper per STM 196. ontact Plating: Silver - STM-700 Gold - MIL-DTL-4504. Gaskets: Silicone rubber per ZZ-R-765, lass II, Grade 50. Other Metal Parts: rass per STM 16 Plated: Silver - STM 700 Nickel - MS-QQ-N-90. ll other specifications are in accordance with the latest issues of MIL-PRF-3901, or MIL--55339, or other applicable MIL specifications, and interfaces are in accordance with MIL-STD-348. *These specifications are typical and may not apply to all connectors. Detailed specifications for individual connectors are available on request. 1 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Plugs dia. Straight Plug - Military lamp For Flexible dia. 1 Dimensions Plating ssembly Procedure/ ody ontact Trim ode 1 1.560 Nickel Silver 1001001N000-001 /06, 3 1 1.66.750 Nickel Silver UG-959/U /01, 3 1 1.66.750 Silver Gold ( ) M3901/16-05 /01 5, 6 1.03.440 Nickel Silver UG-88/U /04 5, 6 1.06 Nickel Silver UG-88/U /17 5, 6 1.06 Nickel Silver UG-88E/U /17 5, 6 1.06 Nickel Gold ( ) 1001015N001-000 /17 5, 6 1.06 Silver Gold ( ) M3901/16-0101 /17 7 1.03.440 Nickel Silver UG-60/U /04 7 1.06 Nickel Silver UG-60/U /17 7 1.06 Nickel Silver UG-60D/U /17 7 1.06 Nickel Silver ( ) 100101N001-000 /17 7 1.06 Silver Gold ( ) M3901/16-010 /17 8 1.06 Nickel Silver UG-1033/U /17 8 1.06 Nickel Silver ( ) 100109N001-000 /17 8 1.06 Silver Gold ( ) M3901/16-0103 /17 8 1.06 Nickel Silver 1001043N000-000 /17 8 1.06 Nickel Silver ( ) 1001043N001-000 /17 9 1.06 Nickel Silver 1001036N000-000 /18 9 1.06 Nickel Silver ( ) 1001036N001-000 /18 9 1.06 Silver Gold ( ) M3901/16-00 /37 11 1.06 Nickel Silver 1001038N000-000 /18 1.06 Silver Gold ( ) M3901/16-0118 /17 3 1.06 Silver Gold ( ) M3901/16-0111 /17 5 1.06 Nickel Silver 100113N000-000 /17 Straight Plug - Solder lamp For Semi-Rigid dia. 1 Dimensions Plating ssembly Procedure/ ody ontact Trim ode 13 1 1.06 Nickel* Silver 1001031N003-000 F/08 14 1 1.06 Nickel* Silver 100105N003-000 F/07 See page 09 for cable groups. ssembly procedures start on page 10. * Solder ferrule is gold plated. Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Plugs Straight Plug - Heli-Grip For Flexible dia. Heli-Grip ttachment 1 These connectors have captivated contacts and allow rapid, easy assembly simply trim the cable, slide into the cone/insulator/contact assembly (left), solder the center conductor to the contact, and screw body assembly (right) onto cable assembly. Dimensions Plating ssembly Procedure/ ody ontact Trim ode 5, 6 1 1.06 Nickel Silver ( ) 1001018N005-000 E/03 RG-3 1 1.06 Nickel Silver ( ) 1001015N005-003 E/03 7 1 1.06 Nickel Silver ( ) 1001019N005-000 E/03 8 1 1.06 Nickel Silver ( ) 100109N005-001 E/03 8 1 1.06 Nickel Silver ( ) 1001043N005-000 E/03 9 1 1.06 Nickel Silver ( ) 1001037N005-000 E/03 10 1 1.06 Nickel Silver ( ) 1001100N005-000 E/03 11 1 1.06 Nickel Silver ( ) 1001038N005-000 E/03 Except RG-3/U. Straight Plug - rimp Type For Flexible (crimp sleeve) (crimp sleeve) 1 Dimensions Plating ody ontact ssembly Procedure/ Trim ode 3, 4 1 1.7.630 Nickel Gold ( ) 1003005N000-000 /11 5 1.09 Nickel Gold 1003017N000-000 /18 5 1.10 Nickel Gold ( ) 1003017N00E-00 /19 6 1.09 Nickel Gold 1003013N000-000 /18 6 1.10 Nickel Gold ( ) 1003013N00E-000 /19 7 1.09 Nickel Gold 100300N000-00 /18 7 1.10 Nickel Gold ( ) 1003019N00E-00 /19 7 1.05.410 Nickel Silver 100300N000-005 * *** 7 1.05.410 Nickel Gold 100300N000-006 * *** 7 1.05 Nickel Silver ( ) 100300N001-005 * *** 7 1.05 Nickel Gold ( ) 100300N001-009 * *** 9.940.310 Nickel Silver ( ) 1003037N000-000 /0 * rimp center contact. See page 09 for cable groups. ssembly procedures start on page 10. ***ontact factory for cable assembly instructions. 3 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Plugs Right ngle Plug - Military lamp For Flexible 1 Dimensions Plating ody ontact 1 1 1.3 1.9.750 Nickel Gold, 3 1 1.3 1.9.750 Nickel Silver 5, 6 1.09 1.61 Nickel Silver 5, 6 1.09 1.61 Nickel Silver 5, 6 1.09 1.61 Nickel Silver 5, 6 1.09 1.61 Silver Gold 5, 6 3 1.5 1.06.440 Nickel Silver 7 1.09 1.61 Nickel Silver 7 1.09 1.61 Nickel Silver 7 1.09 1.61 Silver Gold 7 3 1.5 1.06.440 Nickel Silver 8 3 1.5 1.06.440 Nickel Silver 8 1.09 1.61 Nickel Silver 9 1.09 1.61 Nickel Silver 9 3 1.5 1.06.440 Nickel Silver 1.09 1.61 Silver Gold 3 ssembly Procedure/ Trim ode 1004001N000-000 /07 1004004N000-000 /07 UG-913/U /17 UG-913/U /17 ( ) 1004015N001-000 /17 ( ) M3901/0-0101 /17 ( ) 1005014N000-000 /05 100401N000-000 /17 ( ) 100401N001-000 /17 ( ) M3901/0-010 /17 ( ) 100501N000-001 /05 ( ) 100509N000-000 /05 1004043N000-000 /17 1004036N000-000 /18 ( ) 1005036N000-000 /05 ( ) M3901/0-0108 /17 Right ngle Plug - Solder lamp For Semi-Rigid 1 Dimensions Plating ssembly Procedure/ ody ontact Trim ode 13 1 1.09 1.61 Nickel* Silver 1004031N003-000 F/08 14 1 1.09 1.61 Nickel* Silver 100405N003-000 F/07 * Solder ferrule is gold plated. See page 09 for cable groups. ssembly procedures start on page 10. 4 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Plugs Right ngle Plug - Heli-Grip For Flexible Heli-Grip ttachment 1 These connectors have captivated contacts and allow rapid, easy assembly simply trim the cable, slide into the cone/insulator/contact assembly (left), solder the center conductor to the contact, and screw body assembly (right) onto cable assembly. Dimensions Plating ssembly Procedure/ Trim ode ody ontact 5, 6 1 1.09 1.61 Nickel Silver ( ) 1004018N005-000 E/03 RG-3 1 1.09 1.61 Nickel Silver ( ) 1004015N005-000 E/03 7 1 1.09 1.61 Nickel Silver ( ) 1004019N005-000 E/03 8 1 1.09 1.61 Nickel Silver ( ) 100409N005-000 E/03 8 1 1.09 1.61 Nickel Silver ( ) 1004043N005-000 E/03 9 1 1.09 1.61 Nickel Silver ( ) 1004037N005-000 E/03 10 1 1.09 1.61 Nickel Silver ( ) 1004100N005-000 E/03 11 1 1.09 1.61 Nickel Silver ( ) 1004038N005-000 E/03 Except RG-3/U. Right ngle Plug - rimp Type For Flexible (crimp sleeve) 1 Dimensions Plating ssembly Procedure/ ody ontact Trim ode 5 1 1.03 1.71 Nickel Gold ( ) 1007017N000-003 /0 6 1 1.03 1.71 Nickel Silver 1007015N000-000 /0 7 1 1.03 1.71 Nickel Gold 1007019N000-001 /0 See page 09 for cable groups. ssembly procedures start on page 10. 5 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Jacks Straight Jacks - For Flexible & Semi-Rigid dia. dia. 1 3 Heli-Grip ttachment These connectors have captivated contacts and allow rapid, easy assembly simply trim the cable, slide into the cone/insulator/contact assembly (left), solder the center conductor to the contact, and screw body assembly (right) onto cable assembly., 3 5, 6 5, 6 5, 6 7 7 7 8 9 9 11 3 5, 6 RG-3 7 8 8 9 10 11 5 6 7 7 1 3 3 3 3 13 14 Except RG-3/U. Military lamp For Flexible Dimensions Plating ody ontact.750 Nickel Silver Nickel Silver Nickel Gold Silver Gold Nickel Silver Nickel Silver Silver Gold Silver Gold Nickel Silver Nickel Silver Nickel Silver Silver Gold Silver Gold 1.75 1.06.410 ssembly Procedure/ Trim ode 1008004N000-000 /0 UG-89/U /17 ( ) 1008015N001-000 /17 ( ) M3901/17-0101 /17 UG-61/U /17 ( ) 100801N001-000 /17 ( ) M3901/17-010 /17 ( ) M3901/17-0103 /17 1008036N000-000 /18 ( ) 1008036N001-000 /18 1008038N000-000 /18 ( ) M3901/17-0118 /17 ( ) M3901/17-0111 /17 Heli-Grip For Flexible Nickel Silver ( ) 1008018N005-001 E/03 Nickel Silver ( ) 1008015N005-000 E/03 Nickel Silver ( ) 1008019N005-000 E/03 Nickel Silver ( ) 100809N005-000 E/03 Nickel Silver ( ) 1008043N005-000 E/03 Nickel Silver ( ) 1008037N005-000 E/03 Nickel Silver ( ) 1008100N005-000 E/03 Nickel Silver ( ) 1008038N005-00 E/03 rimp Type For Flexible Nickel Gold Nickel Gold Nickel Gold Nickel Silver Solder-lamp For Semi-Rigid 1010017N000-001 /05 1010013N000-000 /05 101000N000-000 /05 101000N001-001 ** *** Nickel* Silver 1008031N003-000 F/08 Nickel* Silver 100805N003-000 F/07 *Solder ferrule is gold plated. See page 09 for cable groups. ssembly procedures start on page 10. **Indicates crimp center contact. ***ontact factory for cable assembly instructions. 6 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Jacks ulkhead Jacks - Military lamp For Flexible 1.00 hex.687 hex 1 (Rear mount) (Rear mount).65 hex.65 dia. 3 (Front mount) 4 (Front mount) Dimensions Mounting Max. Plating Fig. Panel ody ontact ssembly Procedure/ Trim ode, 3 1 1.55.90.750 51.110 Nickel Gold ( ) 1016004N511-000 /0 5, 6.680 59.110 Nickel Silver UG-909/U /17 5, 6.680 59.110 Nickel Silver UG-909/U /17 5, 6.810 59.40 Nickel Silver UG-909/U /17 5, 6.810 59.40 Silver Gold ( ) M3901/19-0101 /17 5, 6.680 59.110 Nickel Gold ( ) 1016015N591-000 /17 5, 6 3 1.14.550.440 57.090 Nickel Silver 1017014N570-000 /04 7.680 59.110 Nickel Silver UG-910/U /17 7.680 59.110 Nickel Silver UG-910/U /17 7.810 59.40 Nickel Silver UG-910/U /17 7.810 59.40 Silver Gold ( ) M3901/19-010 /17 7.680 59.110 Nickel Silver ( ) 101601N591-000 /17 7 4 1.14.550.440 57.090 Nickel Silver UG-64/U /04 8.810 59.40 Silver Gold ( ) M3901/19-0110 /17 9.680 59.110 Nickel Silver 1016036N590-000 /18 9.680 59.110 Nickel Silver ( ) 1016036N591-000 /17 9.810 59.40 Silver Gold ( ) M3901/19-00 /17 11.680 59.110 Nickel Silver 1016038N590-000 /18 11.680 59.110 Nickel Silver ( ) 1016038N591-000 /18.810 59.40 Silver Gold ( ) M3901/19-0118 /17 3.810 59.40 Silver Gold ( ) M3901/19-0111 /17 See page 09 for cable groups. ssembly procedures start on page 10. See page 08 for mounting dimensions. 7 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Jacks ulkhead Jack - Heli-Grip For Flexible Heli-Grip ttachment 1.687 hex (Rear mount) Dimensions Mounting Max. Plating ssembly Fig. Procedure/ Panel ody ontact Trim ode 5, 6 1.810 59.40 Nickel Silver ( ) 1016018N595-000 E/03 RG-3 1.810 59.40 Nickel Silver ( ) 1016015N595-000 E/03 7 1.810 59.40 Nickel Silver ( ) 1016019N595-000 E/03 8 1.810 59.40 Nickel Silver ( ) 101609N595-000 E/03 8 1.810 59.40 Nickel Silver ( ) 1016043N595-000 E/03 9 1.810 59.40 Nickel Silver ( ) 1016037N595-000 E/03 10 1.810 59.40 Nickel Silver ( ) 1016100N595-00 E/03 11 1.810 59.40 Nickel Silver ( ) 1016038N595-00 E/03 Except RG-3/U. These connectors have captivated contacts and allow rapid, easy assembly simply trim the cable, slide into the cone/insulator/contact assembly (left), solder the center conductor to the contact, and screw body assembly (right) onto cable assembly. ulkhead Jack - rimp Type For Flexible Dimensions 1 (Rear mount) Mounting (crimp sleeve) Max. Plating Panel ody ontact Fig. 5 1 1.31.680 59.110 Nickel Silver 6 1 1.31.680 59.110 Nickel Silver 7 1 1.31.680 59.110 Nickel Silver.687 hex ssembly Procedure/ Trim ode 1019016N590-000 /1 1019013N590-000 /1 101900N590-000 / Fig. Dimensions ulkhead Jack - Solder lamp For Semi-Rigid 1 (Rear mount) Mounting 13 1.810 59.40 Nickel* Silver 14 1.810 59.40 Nickel* Silver Max. Plating ssembly Procedure/ Panel ody ontact Trim ode 1016031N593-000 F/08 101605N593-000 F/07 * Solder ferrule is gold plated. See page 09 for cable groups. ssembly procedures start on page 10. See page 08 for mounting dimensions..687 hex 8 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Jacks Panel Jack- Military lamp For Flexible 1 Dimensions Mounting Plating Fig. ody ontact ssembly Procedure/ Trim ode 1 1 1.75.630.750 33 Nickel Silver 1011001N330-000 /0, 3 1 1.75.630.750 33 Nickel Silver 1011004N330-000 /0 5, 6.550 07 Nickel Silver UG-91/U /17 5, 6.550 07 Silver Gold ( ) M3901/18-010 /17 5, 6.550 07 Nickel Gold ( ) 1011015N071-000 /17 7.550 07 Nickel Silver UG-6/U /17 7.550 07 Silver Gold ( ) M3901/18-0101 /17 7.550 07 Nickel Silver ( ) 101101N071-000 /17 8.550 07 Silver Gold ( ) M3901/18-0103 /17 9.550 07 Nickel Silver 1011036N070-000 /18 9.550 07 Nickel Silver ( ) 1011036N071-000 /38 9.550 07 Silver Gold ( ) M3901/18-00 /38 11.550 07 Nickel Silver 1011038N070-000 /18 11.550 07 Nickel Silver ( ) 1011038N071-000 /18.550 07 Silver Gold ( ) M3901/18-0118 /17 3.550 07 Silver Gold ( ) M3901/18-0111 /17 Panel Jack - Solder-lamp For Semi-Rigid 1 Dimensions Mounting Plating ssembly Fig. Procedure/ ody ontact Trim ode 13 1.550 07 Nickel* Gold 1011031N073-000 F/08 14 1.550 07 Nickel* Gold 101105N073-000 F/07 * Solder ferrule is gold plated. See page 09 for cable groups. ssembly procedures start on page 10. See page 08 for mounting dimensions. 9 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Jacks Panel Jack- Heli-Grip For Flexible Heli-Grip ttachment These connectors have captivated contacts and allow rapid, easy assembly simply trim the cable, slide into the cone/insulator/contact assembly (left), solder the center conductor to the contact, and screw body assembly (right) onto the cable assembly. 1 Dimensions Mounting Plating Fig. ody ontact ssembly Procedure/ Trim ode 5, 6 1.550 07 Nickel Silver ( ) 1011018N075-000 E/03 RG-3 1.550 07 Nickel Silver ( ) 1011015N075-000 E/03 7 1.550 07 Nickel Silver ( ) 1011019N075-000 E/03 8 1.550 07 Nickel Silver ( ) 101109N075-000 E/03 8 1.550 07 Nickel Silver ( ) 1011043N075-000 E/03 9 1.550 07 Nickel Silver ( ) 1011037N075-000 E/03 10 1.550 07 Nickel Silver ( ) 1011100N075-000 E/03 11 1.550 07 Nickel Silver ( ) 1011038N075-000 E/03 Except RG-3/U. Panel Jack - rimp Type for Flexible (crimp sleeve) 1 Dimensions Mounting Plating Fig. ody ontact ssembly Procedure/ Trim ode 5 1 1..630 09 Nickel Gold ( ) 1055017N091-000 /1 6 1 1..630 09 Nickel Gold ( ) 1055015N091-000 /1 7 1 1..630 09 Nickel Gold ( ) 1055019N091-000 /1 See page 09 for cable groups. ssembly procedures start on page 10. See page 08 for mounting dimensions. 10 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Receptacles Panel Jack Receptacles - Sqaure Flange (I.D. ) 1 (Turret contact) (Solder pot contact) D (I.D. ) D.161 dia..050 dia. 3 (Solder pot contact, 1" square flange, interchangeable with type N standard flange size) D 4 (Post contact).085 dia..75 dia..050 dia..161 dia. D 5 (Post contact) D 6 (Post contact, 1/" square flange, interchangeable with SM standard flange size) Dimensions Mounting Plating D ody ontact 1 1.06.550.050. 18 Nickel Silver ( ) UG-185/U 1.06.630.06.090 07 Nickel Silver ( ) UG-90/U 1.06.630.043.090 1 Nickel Silver ( ) UG-447/U 1.06.630.06.090 07 Silver Gold ( ) M3901/-0001 1.06.630.06.090 09 Nickel Silver ( ) 1013000N090-000 1.06.630.06.090 10 Nickel Silver ( ) 1013000N100-000 1.06.630.06.090 18 Nickel Gold ( ) 1013000N180-000 1.00.750.06.080 18 Nickel Gold ( ) 1013000F181-000 ** 3 1.06.630.06.080 33 Nickel Silver ( ) 1013000N330-000 4.715.090.175.375 09 Nickel Silver ( ) 1058000N091-000 5.750.080.590.705 18 Nickel Gold ( ) * 1058000N181-001 6.750.080.590.705 05 Nickel Gold ( ) 1058000N051-000 () in contact plating column indicates captive contact. *Indicates epoxy-captivated contact. **Insulator flush with rear of flange. Flange #18 except with.15 dia. mounting holes. See page 6 for alternate body plating information. See page 08 for mounting dimensions. ll items are available with other flange sizes and contact configurations. 11 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Receptacles Right ngle Panel Jack Receptacles - Sqaure Flange D (I.D. ) D (I.D. ) 1 (Solder pot contact) Dimensions Mounting Plating D ody ontact (Solder pot contact, 1" square flange, interchangeable with type N standard flange size) 1 1.09.910.610.06 18 Nickel Silver ( ) UG-535/U 1 1.06.910.650.06 07 Nickel Silver ( ) 1015000N070-000 1 1.06.910.650.06 09 Nickel Gold ( ) 1015000N090-000 1..910.610.06 33 Nickel Silver ( ) 1015000N330-000 Panel Plug Receptacles - Sqaure Flange (I.D. ) D (I.D. ) D 1 (Solder pot contact, 3/4" square flange) (Solder pot contact, 1" square flange, interchangeable with type N standard flange size) Dimensions Mounting Plating D ody ontact 1 1.19.800.06.090 18 Nickel Silver ( ) UG-1104/U 1.19.800.06.080 33 Nickel Silver ( ) 103000N330-000 Dummy Receptacles Dimensions Mounting See page 08 for mounting dimensions. ll items are available with other flange sizes and contact configurations. ody Plating on t a ct. 750.090 09 N ickel 1063000N090-000 1 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Receptacles ulkhead Jack Receptacles (I.D. ) (I.D. ) dia. 1 (Front mount).570 dia. (Front mount, pressurized [nonhermetic], with mounting gasket) (I.D. ) (I.D. ).687 dia. 3 (Rear mount, hermetically sealed, with mounting gasket).594 dia..06 (I.D. ).594 dia. 4 (Front mount, hermetically sealed, with mounting gasket) 5 (Right angle, solder pot contact) Dimensions Max. Mounting Plating Panel ody ontact 1 1.06.490.06.130 6 Nickel Silver ( ) UG-65/U 1.8.600.05.190 75 Nickel Silver ( ) UG-657/U 1.8.600.05.190 75 Nickel Silver ( ) UG-657/U 1 1.06.470.06.130 65 Nickel Silver ( ) UG-1094/U 1 1.19.470.06.60 65 Nickel Silver ( ) UG-1094/U 1 1.06.490.06.130 6 Silver Gold ( ) M3901/1-0001 1 1.19.470.06.60 65 Silver Gold ( ) M3901/1-000 1 1.19.470.06.60 6 Silver Gold ( ) M3901/1-0003 3 1.0.830.06.60 59 Nickel Silver ( ) UG-911/U 3 1.0.830.06.60 59 Silver Gold ( ) M3901/4-0001 4 1.0.50.06.60 63 Nickel Silver ( ) UG-91/U 4 1.33.50.06.340 63 Nickel Silver ( ) UG-91/U 4 1.0.50.06.60 63 Silver Gold ( ) M3901/4-000 5.90 1..590.130 63 Nickel Silver ( ) UG-1098/U 5.90 1.34.590.50 63 Nickel Silver ( ) UG-1098/U 5.90 1..590.130 6 Nickel Silver ( ) UG-1174/U See page 08 for mounting dimensions. ll items are available with other flange sizes and contact configurations. 13 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Receptacles ulkhead Jack Receptacles With Solder Lug.65 dia..04 dia. Grounding lug 1 (Standard grounding) (I.D. ) Isolated-Ground Receptacles onnector body mounting components Panel.56 hex (I.D. ) Isolating insulator Primary insulator Grounding lug.04 dia. Grounding lug (Isolated ground) These receptacles feature an additional insulator between the main connector body and the body s mounting surfaces, electrically isolating the ground signal of the circuit from the panel. The circuit ground signal is passed through the panel via the solder lug for termination inside the equipment. Since they are not a triaxial connector design, isolated-ground receptacles can be used with any standard N plugs. Dimensions Max. Mounting Plating Panel ody ontact 1 1.06.750.06.170 59 Nickel Gold ( ) 101000N591-000 1.06.06.170 59 Nickel Gold ( ) 100000F59G-000 ulkhead Plug Receptacles 1 (Front mount) (I.D. ) ulkhead Plug Receptacle Dimensions Max. Mounting Plating Panel ody ontact 1 1.5.690.06.160 65 Nickel Silver ( ) 104000N651-000 See page 08 for mounting dimensions. ll items are available with other flange sizes and contact configurations. 14 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Receptacles Receptacles For Printed ircuit oards.040 sq. typ. sq. D dia..038 dia. typ..687 sq. D dia..400 typ. 1 typ..45 dia..30 typ..040 sq. typ..030 dia. 3 D.040 sq. typ. sq. D dia..400 typ. 4.038 dia. typ..687 sq. D dia. typ. 5 Dimensions Max. oard Mounting Plating D Thickness ody ontact 1.660.040.116.040.063 P01 Nickel Gold ( ) 1058000N04P-000 1 1.15.040.116.040.063 P01 Nickel Gold ( ) 1058000N04P-001.650.085.50.038.15 P0 Nickel Gold ( ) 1058000N13P-000 3 1.03.050.15.160.063 P03 Nickel Silver ( ) 1067000N91P-001 4 1.06.575.116.040.063 P01 Nickel Gold ( ) 1069000N03P-000 5.950.610.50.038.15 P0 Nickel Gold ( ) 1069000N13P-000 8 holes, dia. x deep b.c..750 dia. Socket contact E dia. x F deep 1 H D Dimensions G Stripline Receptacles.63 dia. D dia. b.c. holes, dia. x deep.875 dia. P la t in g D E F G H ody ontact.085 dia..10 dia. 1.078.310.063.063.0.88.375 Nickel Gold () 1056000N000-000 #-56.15 10.734.15.010.710.15 Nickel Gold 1057000N000-000 See page 08 for mounting dimensions. E F H G 15 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N Receptacles Press Mount Receptacles Delta Press Mount Receptacles Internal ircuitry omponent housing These connectors eliminate the need for complicated mounting hole patterns and mounting hardware. They are simply pressed into a single through hole, and the precisely-engineered knurled mounting section provides retention strength far greater than normal mating and unmating forces. n integral shoulder provides a positive stop when mounting. PressMounts are available for a wide variety of Delta connector series, and can be used in packages as small as the outer diameter of the connector body..43 dia..600.43 dia..600.316 dia. over knurl dia. 1 (Post contact).175.316 dia. over knurl (I.D. ).083 dia. (Solder pot contact).175.65 dia..600.65 dia..860 dia. dia..454 dia. over knurl 3 (Post contact).5.454 dia. over knurl 4 (Plug type, post contact).5 Dimensions Min. Mounting Plating Panel Hole ody ontact 1.06.050.150.31 ±.001 dia. Nickel Silver ( ) 100000N911-001.85.06.150.31 ±.001 dia. Nickel Silver ( ) 100000N911-00 3.060.050.00.450 ±.001 dia. Nickel Gold ( ) 100000N911-013 4.060.050.00.450 ±.001 dia. Nickel Gold ( ) 104000N911-004 ll items are available with other flange sizes and contact configurations. 16 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N ccessories Resistive Termination (Plug Type) (I.D. ) Resistor Dimensions Plating Features ody ontact 51Ω ±5%, 1 / W att 1.5 3.50.144 Nickel Gold ( ) MX-554/U 51Ω ±5%, 1 / W att 1.41 3.50.144 Nickel Silver ( ) MX-554/U 51Ω ±5%, 1 / Watt 1.14.. No chain Nickel Gold ( ) 1031000N00-003 51Ω ± 5%, 1 W att 1.50 4.50.130 Nickel Silver ( ) 1051000N000-000 51Ω ±5%, 1 Watt 1.39.. No chain Nickel Silver ( ) 1051000N00-005 75Ω ±5%, 1 / W att 1.41 3.50.144 Nickel Silver ( ) 1031000N000-004 75Ω ±5%, 1 / Watt 1.14.. No chain Nickel Gold ( ) 1031000N00-001 75 Ω ±5%, 1 Watt 1.39.. No chain Nickel Silver ( ) 1051000N00-00 Dust aps (I.D. ) (I.D. ) 1 (Shown with bead chain) (Shown with safety chain) Dimensions Features Plating ody ontact 1.670.5.144 ead chain Nickel W-13/U 1.590.. No chain Nickel W-155/U 1.690.5.144 ead chain / shorting type Nickel Silver ( ) W-159/U 1.670.5.144 ead chain Silver M3901/5-0006 1.670.70.50 Safety chain Silver M3901/5-0007.690 3.5.81 ead chain Nickel W-8/U.690 3.5.81 ead chain Silver M3901/5-0008.690 3.5.81 Safety chain Silver M3901/5-0009 aps and terminations are available with other chain styles and/or resistances. 17 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N dapters ulkhead Jack-Jack dapter (onnects Two Plugs) Dimensions Max. Mounting Plating Panel ody ontact 1.53.860.690.75 59 Nickel Silver ( ) UG-49/U * 1.53.860.690.75 59 Nickel Silver ( ) UG-49/U * 1.53.860.690.75 59 Nickel Silver ( ) UG-49D/U * 1.53.860.690.75 59 Silver Gold ( ) M55339/13-0049 * 1.8.800.65.160 59 Nickel Silver ( ) 106000N591-000 Panel Mounted Jack-Jack dapter (onnects Two Plugs) * Hermetically sealed, with mounting gasket. Dimensions Plating Mounting ody ontact 1.8. 690 07 Nickel Silver ( ) UG-414/U Straight Jack-Jack dapter (onnects Two Plugs) dia. Dimensions ody ontact Plating 1.8.440 Nickel Silver ( ) UG-914/U 1.8.440 Silver Gold ( ) M55339/16-00914 1.8.440 Nickel Gold ( ) 108000N001-003 See page 08 for mounting dimensions. 18 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N dapters Straight Plug-Plug dapter (onnects Two Jacks) Straight Plug-Jack dapter (onnects One Jack & One Plug) 1. 1.5 ody Plating ontact Nickel Silver ( ) UG-491/U Silver Gold ( ) M55339/15-00491 Plating ody ontact Nickel Gold ( ) 1034000N000-000 Right ngle & Tee dapter 1 (Right angle plug jack; connects one plug and one jack) (Tee jack plug jack; connects two plugs and one jack) 3 (Tee jack jack jack; connects three plugs) 4 (Tee jack jack plug; connects two plugs and one jack) Dimensions Plating ody ontact 1 1.06.880 Nickel Silver ( ) UG-306/U 1 1.06.880 Nickel Silver ( ) UG-306/U 1 1.06.880 Silver Gold ( ) M55339/14-00306 1 1.06.880 Nickel Gold ( ) 109000N000-003 1.8 1.03 Nickel Silver ( ) UG-74/U 1.8 1.03 Nickel Silver ( ) UG-74/U 1.8 1.03 Nickel Gold ( ) UG-74/U 1.8 1.03 Silver Gold ( ) M55339/17-0074 3 1.8.890 Nickel Silver ( ) 1038000N000-00 3 1.8.970 Silver Gold ( ) M55339/17-0000 4 1.50 1.06 Nickel Silver ( ) 1049000N000-000 4 1.50 1.06 Silver Gold ( ) M55339/17-00001 () in contact plating column indicates captive contact. See page 6 for alternate body plating information. 19 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N75 onfigurations N75 onnectors Straight Plugs...31 Right ngle Plugs...31 ulkhead Jacks...31 Panel Jack Receptacles (square flange)...3 Panel Plug Receptacles...3 Printed-ircuit oard Receptacles...3 ulkhead Jack Receptacles...33 In-Series dapters...33 dia. Straight & Right ngle Plugs For Flexible (crimp sleeve).50 (crimp sleeve) 1 (Heli-Grip cable hardware) (rimp type) 3 (rimp type) Dimensions Plating ssembly Procedure/ ody ontact Trim ode 7 1 1.06 Nickel Silver ( ) 7501019N005-000 E/03 7 1.09 Nickel Gold 750300N000-00 /19 7 1.05.410 Nickel Gold ( ) 750300N001-000 /6 7 3 1.03 1.71 Nickel Gold 7507019N000-000 /0 9 1 1.06 Nickel Silver ( ) 7501037N005-000 E/03 9 1.13.390 Nickel Gold 7503037N001-000 /7 9 3 1.03 1.71 Nickel Gold 7507037N000-000 /0 6 1.10.450 Nickel Gold ( ) 7503108N001-000 /6 31 1.13 Nickel Gold 750379N001-000 /19 ulkhead Jack - Heli-Grip For Flexible Heli-Grip ttachment 1 (Rear mount).687 hex These connectors have captivated contacts and allow rapid, easy assembly simply trim the cable, slide into the cone/insulator/contact assembly (left), solder the center conductor to the contact, and screw body assembly (right) onto cable assembly. Dimensions Mounting Max. Plating Fig. Panel ody ontact ssembly Procedure/ Trim ode 7 1.810 59.40 Nickel Gold ( ) 7516019N595-000 E/03 9 1.810 59.40 Nickel Gold ( ) 7516037N595-000 E/03 See page 09 for cable groups. ssembly procedures start on page 10. See page 08 for mounting dimensions. 0 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
Panel Jack & Plug Receptacles - Square Flange N75 Receptacles (I.D. ) (I.D. ) D D 1 (Solder pot contact, 11 /16" square flange) (Solder pot contact, 1" square flange, interchangeable with type N standard flange size) (I.D. ) D (I.D. ) D 3 (Solder pot contact, 3 /4" square flange) 4 (Solder pot contact, 1" square flange, interchangeable with type N standard flange size) Dimensions Mounting Plating D ody ontact 1 1.06.630.030.090 09 Nickel Gold ( ) 7513000N091-000 1.06.630.030.080 33 Nickel Gold ( ) 7513000N331-00 3 1.19.800.030.090 18 Nickel Gold ( ) 753000N180-000 4 1.19.800.030.080 33 Nickel Gold ( ) 753000N331-001 Receptacles For Printed ircuit oards.038 dia. typ..038 dia. typ..687 sq. D dia..687 sq. D dia. typ. typ. 1 Dimensions Max. oard Mounting Plating D Thickness ody ontact 1.650.085.50.038.15 P0 Nickel Gold ( ) 7567000N13P-001 1.34.50.15.038.063 P0 Nickel Silver ( ) 7569000N13P-000 () in contact plating column indicates captive contact. See page 08 for mounting dimensions. See page 6 for alternate body plating information. 1 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
N75 Receptacles & dapters ulkhead Jack Receptacles (I.D. ) D max. panel (I.D. ) D max. panel dia..468 hex 1 (D-hole mounting) (Round hole mounting) Dimensions Mounting Plating D ody ontact 1 1.06.570.030.130 65 Nickel Gold ( ) 750000N651-001 1.06.470.030.130 89 Nickel Gold ( ) 751000N61-00 ulkhead Jack - Jack dapter (onnect Two Plugs) Dimensions Max. Mounting Plating Panel ody ontact 1.8.760.65.160 59 Nickel Silver ( ) 756000N591-000 * 1.8.800.65.160 59 Nickel Silver ( ) 756000N591-001 Straight & Right ngle dapters dia. 1 (Right angle plug jack; connects one plug and one jack) (Straight plug plug; connects two jacks) 3 (Straight jack jack; connects two plugs) Dimensions Plating ody ontact 1 1.06.880 Nickel Gold ( ) 759000N000-000 1.. Nickel Gold ( ) 757000N001-000 3 1.8.440 Nickel Gold ( ) 758000N001-000 See page 08 for mounting dimensions. *Isolated ground mounting. Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
ssembly Procedures ssembly Procedure 1) Trim cable jacket to dimension. Slide backnut, washer, V-gasket, and braid clamp onto cable as shown. jacket should bottom on step in braid clamp. acknut V-Gasket Washer (if supplied) raid lamp Washer and/or bushing (if supplied) ontact (captive) & insulator or ontact (non-captive) ) omb braid wires out straight and fold back over front shoulder of braid clamp (braid wires should not overlap one another after folding). Trim braid wires flush with step of braid clamp. Trim cable dielectric and center conductor to dimensions and. Fold braid over 3) If support insulator is provided for RG-6 or 71 cable, insert into hollow in dielectric. ssemble rear bushing or washer (if supplied), rear insulator (if captive contact) and contact, and solder contact to center conductor. Rear of contact should be flush with cable dielectric end. For right angle connectors with access cap, omit this step entirely. Non-captive ontact Solder aptive ontact Washer or bushing (if supplied) Solder 4) Insert prepared cable and hardware into body and tighten backnut. For right angle connectors with access cap, solder center conductor into slot in contact and tighten access cap. Trim odes For ssembly Procedure ode /01.375 (3/8).047 (3/64).03 (13/64) /0.375 (3/8).109 (7/64).03 (13/64) /03.438 (7/16).50 (1/4).188 (3/16) /04.81 (9/3).047 (3/64).15 (1/8) /05.313 (5/16).15 (1/8).109 (7/64) /06.594 (19/3).391 (5/64).156 (5/3) /07.375 (3/8).047 (3/64).15 (1/8) /08.81 (9/3).109 (7/64).094 (3/3) /09.344 (11/3).109 (7/64).094 (3/3) /10.406 (13/3).109 (7/64).03 (13/64) /11 (1/).81 (9/3).156 (5/3) /1.343.040.19 /13.375 (3/8).15 (1/8).156 (5/3) /14.355.090.188 (3/16) /15.45.094 (3/3).59 /16.38 (1/64).094 (3/3).188 (3/16) /17.375 (3/8).109 (7/64).15 (1/8) /18.375 (3/8).06 (1/16).17 (11/64) /19.375 (3/8).188 (3/16).094 (3/3) ode /0.375 (3/8).047 (3/64).17 (11/64) /1 (1/).313 (5/16).17 (11/64) /.375 (3/8).188 (3/16).141 (9/64) /3.438 (7/16).078 (5/64).17 (11/64) /4 (1/).094 (3/3).141 (9/64) /5.438 (7/16).141 (9/64).17 (11/64) /6.65 (5/8).81 (9/3).50 (1/4) /7.688 (11/16).81 (9/3).15 (1/8) /8.656 (1/3).97 (19/64).50 (1/4) /9.688 (11/16).15 (1/8).313 (5/16) /30.688 (11/16).469 (15/3).156 (5/3) /31.700 (1/3).453 (9/64).50 (1/4) /3.313 (5/16).078 (5/64).188 (3/16) /33.50 (1/4).078 (5/64).094 (3/3) /34.50 (1/4).06 (1/16).109 (7/64) /35.837.575.150 /36.450.50.150 /37.81.038.188 /38.81.069.156 I- Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
ssembly Procedures ssembly Procedure rimp Sleeve ontact (captive) 1) Trim cable per chart. Slide crimp sleeve back onto cable. or ontact (non-captive) ) If support insulator is provided for RG-6 or 71 cable, insert into hollow in dielectric. Solder contact onto center conductor; back of contact flush with trimmed end of cable dielectric (omit this step for right angle connectors with access caps). Flare cut end of braid slightly by rotating dielectric. Solder 3) Insert cable/contact into rear of body, with all braid wires on outside of crimp tail. a) For captive contact connectors, push cable in until contact snaps into insulator. b) For noncaptive contact connectors, push cable in until cable dielectric bottoms in connector. c) For right angle or tee connectors with access caps, push cable in until end of braid touches connector body shoulder, and cable center conductor rests in contact slot. Trim excess braid wires even with shoulder of body. Slide crimp sleeve forward until flush with body and crimp (see page 11 for hex die sizes). For right angle or tee connectors with access caps: Solder center conductor into contact slot, assemble insulator disc (if supplied), then press cap into body until seated or screw into place. Trim odes For ssembly Procedure ode /01.30.470.140 /0.4.578.17 /03.406.187 /04.85.505.140 /05.335.460.140 /06.187.437.19 /07.4.610.156 /08.4.56.19 /09.313.610.03 /10.80.436.187 /11.430.54.156 /1.300.434.156 /13.300.447.156 /14.40.645.187 /15.300.40.10 /16.31.609.15 /17.50.156 /18.437.56.109 /19.343.437.156 ode /0.50.375.156 /1.45.550.156 /.375.156 /3.81.469.15 /4.50.700.109 /5.343.775.15 /6.343.437.109 /7.313.437.187 /8.19.71.078 /9.00.30.060 /30.650.19 /31.350.840.150 /3.175.60.095 /33.195.70.045 /34.150.50.105 /35.195.80.170 /36.150.35.090 /37.195.95.075 /38.150.5.095 /39.50.300.135 I- Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
ssembly Procedures ssembly Procedure Trim odes ode /01.656 (1/3).141 (9/64).50 (1/4) /0 (1/).15 (1/8).50 (1/4) acknut Washer Gasket raid lamp Fold braid over ontact (captive) & insulator or ontact (non-captive) 1) Trim cable jacket to dimension. Slide backnut, washer, gasket, and braid clamp onto cable as shown. jacket should bottom on step in braid clamp. ) omb braid wires out straight and fold back over front shoulder of braid clamp (braid wires should not overlap one another after folding). Trim braid wires flush with edge of braid clamp. Trim cable dielectric and center conductor to dimensions and. /03.450.136.187 /04.375 (3/8).109 (7/64).15 (1/8) /05.375 (3/8).06 (1/16).50 (1/4) /06 (1/).188 (3/16).15 (1/8) /07.575.438.094 Non-captive Solder aptive 3) If support insulator is provided for RG-6 or 71 cable, insert into hollow in dielectric. ssemble rear insulator (if captive contact) and contact, and solder contact to center conductor. Rear of contact should be flush with cable dielectric end. /08.65 (5/8).141 (9/64).19 (7/3) 4) Insert prepared cable and hardware into body and tighten backnut. For right angle connectors with access cap, solder cable center conductor to slot in contact and tighten access cap. ssembly Procedure D rmor lamp acknut V-Gasket Washer raid lamp ontact (captive) & insulator or ontact (non-captive) 1) Slide armor clamp over cable. Push armor back to expose cable end. Slide backnut, washer (if supplied), gasket, and braid clamp onto cable as shown. jacket should bottom on step in braid clamp. Trim cable jacket to dimension. Fold braid over ) omb braid wires out straight and fold back over front shoulder of braid clamp (braid wires should not overlap one another after folding). Trim braid wires flush with edge of braid clamp. Trim cable dielectric and center conductor to dimensions and. Trim odes ode D/01.375 (3/8).047 (3/64).50 (1/4) D/0 (1/).188 (3/16).19 (7/3) D/03.344 (11/3).047 (3/64).19 (7/3) D/04.313 (5/16).047 (3/64).17 (11/64) D/05.65 (5/8).81 (9/3).50 (1/4) Non-captive aptive Solder 3) ssemble rear insulator (if captive contact) and contact, and solder contact to center conductor. Rear of contact should be flush with cable dielectric end. D/06.313 (5/16).06 (1/16).109 (7/64) 4) Insert prepared cable and hardware into body and tighten backnut. Trim armor to fit between armor clamp and braid clamp. Tighten armor clamp. I--D Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
ssembly Procedures ssembly Procedure E acknut ontact/insulator/ cone grip assembly 1) Slide backnut onto cable as shown. Trim cable to dimensions and as shown. Slit jacket to dimension in two places, 180 apart. Trim odes ode E/01.50 (1/4).141 (9/64).313 (5/16) E/0.19 (7/3).063 (1/16).50 (1/4) E/03.50 (1/4).031 (1/3).50 (1/4) Solder ) Slide cone/insulator/contact assembly under braid until braid is flush with shoulder. Solder contact to center conductor. 3) Insert prepared cable and hardware into body; tighten assembly by holding nut stationary and turning body. ssembly Procedure F acknut Washer ontact (captive), insulator, & bushing Trim odes ode F/01.50 (1/4).19 (7/3) V-Gasket Solder Ferrule Solder or ontact (non-captive) 1) Trim cable per chart. Slide backnut, washer, v-gasket, and solder ferrule onto cable. Trimmed end of cable jacket should bottom on step in solder ferrule. F/0.50 (1/4).17 (11/64) F/03.188 (3/16).188 (3/16) F/04.109 (7/64).65 (17/64) F/05.156 (5/3).50 (1/4) F/06.19 (7/3).50 (1/4) F/07.156 (5/3).17 (11/64) Solder aptive Solder Non-captive ) Solder ferrule to cable jacket as shown. Retrim cable dielectric to proper length if it has extruded from soldering heat. Slide bushing and rear insulator over cable dielectric if captive contact. Solder contact onto center conductor; back of contact flush with trimmed end of cable dielectric. F/08.109 (7/64).19 (7/3) 3) Insert prepared cable and hardware into body and tighten backnut. I-E-F Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
ssembly Procedures ssembly Procedure G ring ody Gasket oupling nut Soft solder all around with end of body Trim odes ode G/01.090 70-90 1) Trim cable as shown. Remove any burrs from jacket and center conductor. ) Soft solder cable jacket to body, making sure that end of cable is flush with end of body. fter solder joint has cooled, retrim any protruding dielectric flush with end of body. 3) ssemble ring and gasket to body. ompress ring and slide body assembly into coupling nut until ring is seated in groove. ssembly Procedure H ontact ody assembly Soft solder all around with insulator.015" Trim odes ode H/01.090 H/0.060 H/03.115 H/04.150 1) Trim cable as shown. Remove any burrs from jacket and center conductor. ) Solder contact to center conductor, fixturing to maintain gap as shown. Remove any excess solder from outside of contact. 3) Insert cable into body and solder cable jacket to body, keeping end of cable flush with insulator as shown. Plug body assembly and contact shown; procedure is identical for jack connectors. ssembly Procedure I ody assembly Soft solder all around with insulator Trim odes ode I/01.090 70-90 1) Trim cable as shown. Remove any burrs from jacket and center conductor. ) Insert cable into body and solder cable jacket to body, keeping end of cable flush with insulator as shown. Plug body assembly and contact shown; procedure is identical for jack connectors. Positioner.50-36 UNS- thread For.085" : P/N 63-1007- For.141" : P/N 63-1007-1.50.375 Using this positioner in the final step of assembly procedure H or I (for plugs only) will ensure that the contact and insulator are retained in the proper position to meet MIL--3901 requirements. The positioner should be screwed finger-tight into the mating end of the connector (as shown at right) before the cable jacket is soldered to the body assembly. I-G-I Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
ssembly Procedures ssembly Procedure J Trim odes ode J/01.109.047 J/0.059.039 Soft solder all around Press cap in until seated ap Insulator (if supplied) Solder center conductor to contact J/03.059.079 J/04.050.059 1) Trim cable as shown. Remove any burrs from jacket and center conductor. ) Soft solder cable jacket to body, making sure that end of cable is flush with step in body. Solder center conductor into contact slot, assemble insulator disc (if supplied), then press cap into body until seated or screw into place. ssembly Procedure K Heat-shrink tubing (if supplied) rimp or solder sleeve Solder hole (for solder-type connectors only) 1) Trim cable per chart. Slide crimp (or solder) sleeve and heat-shrink tubing (if supplied) back onto cable. Solder.015" ) Solder contact onto center conductor, fixturing to maintain gap as shown. Flare cut end of braid slightly by rotating dielectric. Heat-shrink tubing rimp or solder sleeve dielectric end 3) Insert cable/contact into rear of body, with all braid wires on outside of crimp tail. Push cable in until cable dielectric bottoms in connector. Trim excess braid wires even with shoulder of body. Slide crimp sleeve forward until flush with body and crimp (see page 11 for hex die sizes). (For solder-type connectors, solder braid to body and sleeve through hole in sleeve.) Slide heat-shrink tubing into place and shrink with hot-air gun. Plug body assembly and contact shown; procedure is identical for jack connectors. Trim odes ode ode K/01.50.70.110 K/07.0.90.135 K/0.00.70.140 K/08.40.60.090 K/03.5.90.110 K/09.090.135.160 K/04.5.330.110 K/10.50.415.115 K/05.50.330.110 K/11.50.400.150 K/06.50.315.095 K/1.8.390.140 I-J-K Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
ssembly Procedures ssembly Procedure L Trim odes ode L/01.50.438.109 L/0.15.19.109 L/03.34.344.109 L/04.195.70.050 L/05.095.155.050 L/06.81.390.070 1) Trim cable per chart. Slide crimp (or solder) sleeve onto cable. Solder hole (for solder-type connectors) rimp or solder sleeve ) Insert cable into rear of body, with all braid wires on outside of crimp tail. Push cable in until end of braid touches connector body shoulder and center conductor rests in contact slot. Slide crimp sleeve forward until flush with body and crimp (see page 11 for hex die sizes). (For solder-type connectors, solder braid to body and sleeve through hole in sleeve.) Solder center conductor into contact slot, assemble insulator disc (if supplied), then press cap into body until seated or screw into place. rimp or solder sleeve Press cap in until seated ap Insulator (if supplied) Solder center conductor to contact ssembly Procedure M Trim odes ode M/01.81.390.140 acknut 1) Trim cable per chart. Slide crimp (or solder) sleeve and backnut onto cable. Solder hole (for solder-type connectors) rimp or solder sleeve lamp Insulator ontact ) Flare cut end of braid slightly by rotating dielectric. Insert cable into rear of clamp, with all braid wires on outside of crimp tail.slide insulator over cable dielectric until it is flush with front of clamp, and cable insulation bottoms inside insulator. Slide contact onto center conductor, with contact shoulder flush with front of insulator. Solder contact to center conductor. Solder 3) Slide crimp sleeve forward until flush with clamp shoulder; crimp as close to shoulder as possible. (see page 11 for hex die sizes). (For solder-type connectors, solder braid to body and sleeve through hole in sleeve.) 4) Insert prepared cable into back of body. Slide nut forward and tighten to 1 15 inch-pounds. rimp Tools For Flexible M50/5-01 * For Delta cable groups. See MIL-PRF-3901 specifications for dies sizes used with M3901 cable groups. Frame only P/N M50/5-01 Use with interchangeable dies listed below. * Hex Die Size Die Set P/N losure, 3, 4.49 hex,.400 wide M50/5-61 5, 6.13 hex,.400 wide M50/5-19 7.55 hex,.400 wide M50/5-19 9.18 hex,.400 wide M50/5-35 10.151 hex,.400 wide M50/5-37 11.105 hex,.400 wide M50/5-33 I-L-M Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
Mounting s onnector Flanges (Panel Mounted onnectors) (L) typ. typ. square 4-hole flanges 04 1/.360.089 05 1/.340.10 07 11/16 #3-56 tap 08 11/16.136 09 11/16.15 10 11/16.10 1 11/16.109 18 3/4.531.136 6 1.718 #6-3 tap 7 1.718 #4-40 tap 30 1.718.166 3 1.718.136 3 1.718.136* 33 1.718.15 34 1 3 /3.81.150 36 1 3 /16.906 #6-3 tap 39 1 3 /16.906.15 40 1 3 /16.906.15 45 1.437.57 91.375.50.067 91.375.3.093 * ountersunk to.45 dia. Panel utouts (ulkhead Mounted onnectors) dia. D-Hole 51.755.73 54.630.598 55.630.583 57.557.531 59.505.473 6.44.410 63.407.36 65.380.348 66.319.9 67.55.36 68.195.176 dia. Double D-Hole 69.755.69 7.630.536 75.380.341 84.319.78 D dia..065 typ. D dia. typ. P.. oard Drilling dia. typ. (L) typ. (L) typ. (P traces are shown for illustrative purpose only, and are not representative of actual circuitry.) oaxial connectors D P01.067.400.00.045 P0.045.50.045 P03.067.300.150.035 P05.067.00.100.055 P06.067.00.100.045 P07.045.177.088.045 P08.03.100.050.03 (L) typ..15 (L) dia. typ. (L) typ. (P traces are shown for illustrative purpose only, and are not representative of actual circuitry.) Twinax onnectors D P04.045.50.045 (L) D dia. typ. dia. -hole flanges D 9.3.481.65.10 9.60.481.65.10 95.640 1.015 1.30.15 Round Hole 8.55 89.380 1 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
s Delta s s 1 RG-5, 5, 5, 1, 1; M17/73, /16 1 1 RG-6, 6; M17/ 1 RG-143, 143, 1, ; M17/73, /11, /16 RG-8, 8, 13; M17/74 RG-11, 11; M17/6 3 RG-9, 9, 9, 14; M17/75 3 3 RG-13, 16; M17/77 3 RG-5; M17/17 4 RG-393; M17/17 5 RG-58, 58, 58, 141, 141; M17/8, /111 6 6 RG-55, 14, 14, 3, 400; M17/60, /84, /18 6 RG-55, 55, 14; M17/60, /84 7 7 RG-59, 59, 59, 6, 6, 6, 6, 10; M17/9, /30, /97 7 RG-71, 71, 71; M17/90 8 8 RG-1; M17/54 8 RG-180, 180, 180, 195; M17/95, /137 9 9 RG-174, 188, 188, 316; M17/15 9 RG-179, 179, 187, 187; M17/94, /136 10 Double-Shielded RG-174, 316; M17/15 11 RG-178, 178, 178, 196, 196; M17/93 1.50" semi-rigid; RG-401; M17/19 13.141" semi-rigid; RG-40; M17/130 14.085" semi-rigid; RG-405; M17/133 15 RG-10, 1, 15; M17/6, /74 16 RG-14, 17; M17/78, /165 17 RG-17, 18 18 RG-18, 19 19 RG-115 0 RG-118, 8 1 RG-16 RG-30 3 RG-303 4 RG-304 5 Special 8X cable; contact factory for details. 6 elden 881 7 RG-108, 108; M17/45 8 RG-,, ; M17/15 9 elden 907; Dearborn 607; IM 73611 30 M17/176 31 T&T 735 RG-5, 5, 1 RG-6, 6 1 RG-8, 8 RG-9, 9, 3 RG-10 15 RG-11, 11 RG-1 15 RG-13 3 RG-14 16 RG-17 17 RG-18 18 RG-1, 1 1 RG-,, 8 RG-55, 55 6 RG-55 6 RG-58, 58, 5 RG-59, 59, 7 RG-6, 6,, 7 RG-71, 71, 7 RG-108, 108 7 RG-115 19 RG-118 0 RG-1 8 RG-16 1 RG-141, 141 5 RG-14, 14 6 RG-14 6 RG-143, 143 1 RG-174 9 RG-174DS 10 RG-178, 178, 11 RG-179, 179 9 RG-180, 180, 8 RG-187, 187 9 RG-188, 188 9 RG-195 8 RG-196, 196 11 RG-10 7 RG-1 1 RG-13 RG-14 3 RG-15 15 RG-17 16 RG-18 17 RG-19 18 RG- 1 RG-3 6 Finder RG-5 3 RG-8 0 RG-30 RG-303 3 RG-304 4 RG-316 9 RG-316DS 10 RG-393 4 RG-400 6 RG-401 1 RG-40 13 RG-405 14 M17/ 1 M17/6 M17/15 8 M17/8 5 M17/9 7 M17/30 7 M17/45 7 M17/73 1 M17/16 1 M17/11 1 M17/74 M17/75 3 M17/17 3 M17/77 3 M17/60 6 M18/84 6 M17/18 6 M17/97 7 M17/54 8 M17/95 8 M17/137 8 M17/15 9 M17/93 11 M17/19 1 M17/130 13 M17/133 14 M17/78 16 M17/165 16 M17/176 30 T&T 735 31 elden 881 6 elden 907 9 Dearborn 607 9 IM 73611 9 Note: MIL-PRF-3901 QPL connectors have cable groups defined by the MIL specification, not the Delta cable groups shown here. See page 185 for M3901 cable groups. Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
Ordering & Warranty Information Warranty We warrant our parts to be free of defects and workmanship for one year from purchase. During that time we will repair or replace (at our option) er s, or military installation costs. No other warranties apply, and no other liability may be assumed or extended by representatives or distributors. The terms of the applicable warranty or warranties, as the case may be, as set forth herein are the sole and exclusive warranty terms that shall have any any product order, resulting from the quotation and such terms and in lieu of all other warranties, expressed or implied, including the implied Returns Returns will be accepted only with a Return uthorization number issued by Delta, and are subject to inspection and acceptance upon arrival. Restocking charges will be determined prior to issusnce of Return uthorization. ll claims for shortages must be made within 30 days of receipt by customer. Ordering Information Order changes, cancellation, or termination will be accepted only with written approval from Delta Electronics Manufacturing. or to sale. opyright, Trademarks, & Patents Entire contents copyright 017, Delta Electronics Manufacturing orporation. Reproduction rights are hereby granted for, and sp urchasing procedures, by Delta customers only. Heli-Grip, PressMount, and Global Manufacturer logo are trademarks. The Heli-Grip design is covered by U.S. and foreign patents. Delta Electronics Manufacturing orporation 416 abot Street, P.O. ox 53 everly, M 01915 FSM/GE 00795 3 Delta Electronics Mfg. orp. deltarf.com 978-97-1060 sales@deltarf.com
Delta Electronics Mfg. orp. www.deltarf.com 978-97-1060 sales@deltarf.com PO ox 53 416 abot St. everly, M 01915