Contact Us: FACTORY UTV LLC. 9237 Beatty Drive Sacramento, CA 95826 Phone : (96) 383-2730 E-mail : info@factoryutv.net Go online: www.factoryutv.net U.H.M.W. Skid Plate / Under Armor package Ultra. High. Molecular. Weight. polyethylene all terrain skid plate / under armor kit for UTV s Installation guide Pioneer 000 & 000 5 206
Pioneer 000 / 000-5 206 Skid Plate Mounting Hardware Kit Front Differential Skid Hardware /4-20 x Flange Bolt /4-20 x 3/4 Self Tapping Bolts 2 4 /4-20 Flange nuts 2 6 #S Main Skid Hardware /4-20 x 3/4 Self Tapping Bolt M6 -. 0 x 35 mm Flange Bolts 2 Nylon Spacer #S 22 Rear Skid Hardware 5/6-8 x 3/4 self tapping bolt L Shaped Mounting Bracket 7 This Kit Requires That You Re-Use Your Stock Skid Mounting Bolts (Minus The Stock Washers) We recommend the use of a thread locker compound When securing bolts 2
Stock skid plate Removal Pioneer 000 / 000-5 (206) Save Stock Bolts For Future Steps Remove all stock skid plates (6x) Total Stock Bolts # Note : Remove plastic pop bolt # First: Remove stock skid Plate Save all stock Bolts (for further steps) will not be reusing stock washers 3
Rear Skid Plate Pioneer 000 / 000-5 (206) # Install L Shaped Mounting Bracket Use : (x) Stock Bolt in center of L bracket Use : (x) 5/6th 8 x 3/4 self tapping bolt Fasten rear lip of L bracket to the top of the rear cross member Tighten all bolts securely before going on to step () L Bracket Direction. Tighten bolts securely J-Clip installed for Future Step # # Install Rear Skid Use : (7x) Stock Bolts W/ (7x) (Provided) Finger tighten bolts for adjustments 4
Main Skid Pioneer 000 / 000-5 (206) Figure #A # S Install: Main Skid Plate Use: Remaining Stock Bolts & Install : Center bolts first, loosely Align Tongue and groove on rear skid plate Finger tighten all bolts # At center top Install: M6 -.0 x 35 flange bolt With nylon spacer ( #S ) And Counter sunk washer, Through mounting hole Starting with the (2x) Rear mounting holes on main skid Make a score or mark the center of the holes () Drill a 3/6th inch hole, thread /4-20 tap if desired Use: /4 20 x 3/4 self tapping bolts for steps 3-4 Follow the same procedure as mentioned in step () for side bolts, Tighten all bolts securely 5
Front Diff Skid Pioneer 000 / 000-5 Make sure marked holes align prior to drilling # Install: Front Differential (Diff) plate Hold diff. plate in place, align with tongue & groove on main skid: Make a score or mark the center of the holes # Drill 3/8 the inch holes, thread /4-20 tap if desired ( see figure: () ) Use: (2x) /4-20 x Flange Bolts w/ /4-20 Ny-Lock Nuts &/ & Repeat previous step for the front () & () Mounts Make a score or mark the center of the holes () Drill 3/6th inch holes, thread /4-20 tap if desired Use: /4 20 x 3/4 self tapping bolts and For () & () Bend upper lip to nose while fastening Tighten all bolts securely 6
A-Arm Guard instructions Pioneer 000 / 000-5 (206) Direction of A-Arms & Spacers Front A-Arm Hardware (8x) x D Clamps (8x) Ny-Lock Nuts (8x) /4 Gold Washers (8x) /4-20 x Counter Sunk Bolts Rear A-Arm Hardware (8x) x Box Clamps (8x) Ny-Lock Nuts (8x) /4 Gold Washers (8x) /4-20 x Counter Sunk Bolts Front A-Arms ( Front A-Arm Guards ) Install : A-Arm guard, Hold in place Align & install Use: x D Clamps with/ /4-20 x counter sunk bolts /4 Gold Washers & Ny Lock Nuts finger tighten bolts to allow adjustment Tighten all bolts securely when done ( Rear A-Arm Guards ) (using similar method) Install : Rear A-Arm Guards Use: x Box Clamps with/ /4-20 x counter sunk bolts /4 Gold Washers & Ny Lock Nuts finger tighten bolts to allow adjustment Tighten all bolts securely when done Rear A-Arms 7