TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic 24-Stage Frequency Divider is frequency divider coisting of 24 stages of flip-flop. The input section is equipped with an inverter to enable to use either RC oscillator circuit or crystal oscillator circuit and to accept pulse from external clock source. Each flip-flop is inverted by the falling edge of the output of previous stage flip-flop and this can count up to the maximum of 2 24 = 16,777,216. Since six outputs, 2 18, 2 19, 2 20, 2 21, 2 22, and 2 23 are available besides of 2 24, adjustment of frequency divided output can be achieved. Weight: 1.00 g (typ.) Pin Assignment Count Capacity Output Count Capacity Q18 2 18 = 262,144 Q19 2 19 = 24,288 Q20 2 20 = 1,048,76 Q21 2 21 = 2,097,12 Q22 2 22 = 4,194,304 Q23 2 23 = 8,388,608 Q24 2 24 = 16,777,216 1
Block Diagram 2
Logic Diagram Internal Flip Flop Logic Diagram Flip Flop Timing Chart 3
Absolute Maximum Ratings (Note) Characteristics Symbol Rating Unit DC supply voltage DD 1 SS 1 0.~ SS 1 + 20 DD 2 SS 1 0.~ DD 1 + 0. Input voltage IN SS 1 0.~ DD 1 + 0. Output voltage OUT SS 1 0.~ DD 1 + 0. DC input current I IN ± ma Power dissipation P D 300 mw Operating temperature range T opr 40~8 C Storage temperature range T stg 6~ C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Recommended Operating Conditio ( SS 1 = SS 2 = 0 ) (Note) Characteristics Symbol Test Condition Min Typ. Max Unit DC supply voltage DD 1, DD 2 3 18 Input voltage IN 0 DD 1 Note: The recommended operating conditio are required to eure the normal operation of the device. Unused inputs must be tied to either CC or GND. 4
Static Electrical Characteristics ( SS 1 = SS 2 = 0, DD 1 = DD 2) Characteristics High-level output voltage Low-level output voltage Output high current Symbol OH I OUT < 1 µa IN = SS, DD OL I OUT < 1 µa IN = SS, DD I OH OH = 4.6 OH = 2. OH = 9. OH = 13. Test Condition 40 C 2 C 8 C IN = SS, DD DD () 1 1 1 Min Max Min Typ. Max Min Max 4.9 9.9 14.9 0.61 2. 1. 4.0 0.0 0.0 0.0 4.9 9.9 14.9 0.1 2.1 1.3 3.4.00.00 1.00 0.00 0.00 0.00 1.0 4.0 2.2 9.0 0.0 0.0 0.0 4.9 9.9 14.9 0.42 1.7 1.1 2.8 0.0 0.0 0.0 Unit ma OL = 0.4 0.61 0.1 1.2 0.42 Output low current I OL OL = 0. OL = 1. 1 1. 4.0 1.3 3.4 3.2 12.0 1.1 2.8 ma IN = SS, DD Input high voltage Input low voltage Input current Quiescent supply current IH IL OUT = 0., 4. OUT = 1.0, 9.0 OUT = 1., 13. I OUT < 1 µa OUT = 0., 4. OUT = 1.0, 9.0 OUT = 1., 13. I OUT < 1 µa 1 1 3. 7.0 11.0 1. 3.0 4.0 3. 7.0 11.0 2.7. 8.2 2.2 4. 6.7 1. 3.0 4.0 3. 7.0 11.0 H level I IH IH = 18 18 0.1 0.1 1.0 L level I IL IL = 0 18 0.1 0.1 1.0 I DD IN = SS, DD (Note) 1 20 0.00 0.0 0.01 20 1. 3.0 4.0 300 600 µa µa Note: All valid input combinatio.
Dynamic Electrical Characteristics (Ta = 2 C, SS 1 = SS 2 = 0, DD 1 = DD 2, C L = 0 pf) Characteristics Output traition time (low to high) Output traition time (high to low) Propagation delay time (IN2-Q18) Propagation delay time (IN2-Q24) Propagation delay time (RESET-Qn) Symbol t TLH t THL t plh t phl t plh t phl t phl Max clock frequency f CL Max clock input rise time Max clock input fall time t rcl t fcl Min clock pulse width t W Min pulse width (RESET) t WH Test Condition DD () 1 1 1 1 1 1 1 1 1 Min Typ. Max Unit 3 6 8 70 3 30 70 3 30 1.1 0. 0.3 1.4 0.6 0.4 220 0 70 9. 17. 23. 200 0 80 200 0 80 9.0 3. 2.7 12 4. 3. 2600 00 70 µs µs MHz No limit µs Input capacitance C IN 7. pf 2 16 60 26 20 38 120 38 120 6
Waveforms for Measurement of Dynamic Characteristics Application Circuit When CR Oscillation is Used as Time Reference When Crystal Oscillation is Used as the Time Reference Typical Data X tal (Hz) C I, C O (pf) R O (Ω) 32.768 k 23 00 k 0 k 60 0 k 1 M 4~0 0 4.194304 M 12~1 0 R f = MΩ 7
Package Dimeio Weight: 1.00 g (typ.) 8
Note: Lead (Pb)-Free Packages DIP16-P-300-2.4A RESTRICTIONS ON PRODUCT USE 060116EBA The information contained herein is subject to change without notice. 0223_D TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical seitivity and vulnerability to physical stress. It is the respoibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situatio in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your desig, please eure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specificatio. Also, please keep in mind the precautio and conditio set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc. 0223_A The TOSHIBA products listed in this document are intended for usage in general electronics applicatio (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ( Unintended Usage ). Unintended Usage include atomic energy control itruments, airplane or spaceship itruments, traportation itruments, traffic signal itruments, combustion control itruments, medical itruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer s own risk. 0223_B The products described in this document shall not be used or embedded to any dowtream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulatio. 0606_Q The information contained herein is presented only as a guide for the applicatio of our products. No respoibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No licee is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 0223_C The products described in this document are subject to the foreign exchange and foreign trade laws. 0223_E 9