MINIATURE RELAY POLE to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES 2 A maximum carrying current Capable of 2 A maximum continuous carrying current in the contact Superior reliability gold-overlay contacts P type: Gold-overlay silver-palladium contacts International terminal pitch of one inch grid terminal layout High sensitivity, low power dissipation types also available Standard types:.4 W (A or B type) High sensitivity types:.2 W (C or E type) Conforms to FCC.32 (high dielectric strength type) UL recognized (File number E3) CSA recognized (File number LR2) RoHS compliant since date code: 433A Please see page for more information ORDERING INFORMATION FBR2 S A D2 U P 2 ( CSA) [Example] (a) (b) (c) (d) (e) (f) (g) (h) (a) Series Name FBR2 (b) Enclosure S: Flux free type N: Plastic sealed type A: Standard A type } (nominal power.4 W type) (c) Coil Power and Schematics B: Standard B type C: High sensitivity C type } (nominal power.2 W type) E: High sensitivity E type (d) Nominal Voltage (Example) D3: 3 VDC D2: 2 VDC (refer to the COIL DATA CHART) (e) UL Standard Nil : Standard U : UL4 recognized (f) Contact Material P : Gold-overlay silver-palladium M : Gold-overlay silver (g) Special Type Nil : Standard 2 : High dielectric strength type (h) CSA Standard Nil : Standard -CSA : UL4 + CSA recognized (e) is U Note: The designation name is stamped on the top of the relay case as follows: (Example) Designation ordered: FBR2SAD-P Stamp: 2SAD-P
SAFETY STANDARD AND FILE NUMBERS UL4 (File No. E3) C22.2 No. 4 (File No. LR34 or LR2) Nominal voltage. to 24 VDC A 2 VDC resistive. A 3 VAC resistive SPECIFICATIONS Contact rating Item Standard (A or B type) High sensitive (C or E type) Contact Arrangement form C (SPDT) Material Resistance (initial) Rating (resistive) Maximum Carrying Current Maximum Switching Power Max. Switching Voltage* Maximum Switching Current Gold-overlay silver-palladium or gold-overlay silver Maximum mω (at. A VDC). A VAC or A 2 VDC 2 A VA or 2 W 2 VAC or VDC.2 A (AC) or 2 A (DC) Minimum Switching load* 2 Plastic sealed ma (reference) Flux free ma Coil Nominal Power (at C) Approximately.4 W Approximately.2 W Operate Power (at C) Approximately.3 W maximum Approximately.4 W maximum Operating Temperature 2 C to + C (no frost) 2 C to + C (no frost) Operating Humidity 4 to %RH Time Value Operate (at nominal voltage) Maximum ms Release (at nominal voltage) Maximum ms Insulation Resistance (initial) Minimum MΩ (at VDC) Dielectric between coil and contacts VAC minute (standard) Strength, VAC minute (high dielectric strength type) between open contacts VAC minute Life Mechanical operations minimum Electrical 3 operations minimum (at A/ 2 VDC resistive load) (Refer to the REFERENCE DATA) operations minimum (at 2 A/ 2 VDC resistive load) operations minimum (at. A/ VDC resistive load) Other Vibration Resistance to Hz (double amplitude of. mm) Shock Resistance Misoperation m/s 2 (± ms) m/s 2 (± ms) Endurance, m/s 2 (± ms) Weight Approximately 4 g * If the switching voltage exceeds the rated contact voltage, reduce the current. The current values vary according to the type of load. * 2 Values when switching a resistive load at normal room temperature and humidity and in a clean environment. The minimum switching load varies with the switching frequency and operation environment. 2
COIL DATA CHART. STANDARD (A or B type) MODEL Nominal Nominal Coil current Must Must Maximum Nominal Coil A type B type voltage resistance (at nominal operate release allowable temperature (±%) voltage) voltage voltage voltage power rise Flux free Plastic sealed Flux free Plastic sealed approx. FBR2SAD-n FBR2NAD-n FBR2SBD-n FBR2NBD-n. VDC Ω 3 ma FBR2SAD3-n FBR2NAD3-n FBR2SBD3-n FBR2NBD3-n 3 VDC Ω ma FBR2SAD-n FBR2NAD-n FBR2SBD-n FBR2NBD-n VDC Ω 9 ma % max. % min. % of Approx. Approx. FBR2SAD-n FBR2NAD-n FBR2SBD-n FBR2NBD-n VDC Ω ma of nominal of nominal nominal mw 4 deg voltage voltage voltage (at nominal (at nominal FBR2SAD9-n FBR2NAD9-n FBR2SBD9-n FBR2NBD9-n 9 VDC Ω ma voltage) voltage) FBR2SAD2-n FBR2NAD2-n FBR2SBD2-n FBR2NBD2-n 2 VDC 3 Ω 3 ma FBR2SAD24-n FBR2NAD24-n FBR2SBD24-n FBR2NBD24-n 24 VDC,2 Ω 9 ma Note: All values in the table are measured at C. 2. HIGH SENSITIVITY (C or E type) MODEL Nominal Nominal Coil current Must Must Maximum Nominal Coil C type E type voltage resistance (at nominal operate release allowable temperature (±%) voltage) voltage voltage voltage power rise Flux free Plastic sealed Flux free Plastic sealed approx. FBR2SCD-n FBR2NCD-n FBR2SED-n FBR2NED-n. VDC 2 Ω 2 ma FBR2SCD3-n FBR2NCD3-n FBR2SED3-n FBR2NED3-n 3 VDC 4 Ω ma FBR2SCD-n FBR2NCD-n FBR2SED-n FBR2NED-n VDC Ω 42 ma % max. % min. 22% of Approx. Approx. FBR2SCD-n FBR2NCD-n FBR2SED-n FBR2NED-n VDC Ω 33 ma of nominal of nominal nominal mw 2 deg voltage voltage voltage (at nominal (at nominal FBR2SCD9-n FBR2NCD9-n FBR2SED9-n FBR2NED9-n 9 VDC Ω 23 ma voltage) voltage) FBR2SCD2-n FBR2NCD2-n FBR2SED2-n FBR2NED2-n 2 VDC Ω ma FBR2SCD24-n FBR2NCD24-n FBR2SED24-n FBR2NED24-n 24 VDC 2, Ω 9 ma Note: All values in the table are measured at C. CHARACTERISTIC DATA Range of operation temperature and voltage (Standard.4 W type) Range of operation temperature and voltage (high sensitive.2 W type) Operate and release time data Nominal voltage multiplying factor (%) Coil temperature rise ( C) 3 9 3 Maximum allowable coil voltage Operating voltage range (Data) assumes that the maximum allowable temperature of E type insulation coil is C Must operate voltage 3 Operating temperature ( C) Coil temperature rise data (at C) Nominal voltage multiplying factor (%) Standard (.4 W type) High sensitive (.2 W type). Contact load current (A)..3. 3 9 Operating voltage range Maximum allowable coil voltage Must operate voltage 3 Operating temperature ( C) (Data) assumes that the maximum allowable temperature of E type insulation coil is C Maximum switching capacity AC resistive load ( AC contact rating) DC resistive load ( DC contact rating) Service life (operations) Time (msec) 4 3 2 (x 4 ) Not including bounce time Operate time Release time.2.4.. Coil power (W) Life curve V AC resistive load 2 V DC resistive load 2 V DC resistive load.2.4.. Coil power (W) 3 Contact load current (A)... 2. Contact load current (A) 3
REFERENCE DATA Distribution of operate and release voltage FBR2 Operate n = Release Distribution of operate and release time FBR2 n = Operate Release Distribution of contact resistance FBR2 n = Distribution (%) 3 Distribution (%) Distribution (%) 3 Nominal voltage multiplying factor (%) DIMENSIONS. STANDARD (Flux free type) Dimensions Schematics (BOTTOM VIEW) +.. +.. (A type or C type) (B type or E type).3. +..2 (.24)..3 (.2). 3.2 2.4 2 2 2. N-TYPE (Plastic sealed type) Dimensions Schematics (BOTTOM VIEW) +. +... (A type or C type) (B type or E type).3. +.. 3.2 2 2.2 (2.4) (.9). 2.4 3. PC BOARD MOUNTING HOLE LAYOUT PC board mounting hole layout (BOTTOM VIEW) ø..2 2 3 4 3 Time (ms) Contact resistance (mω). 2.4 Unit: mm 4
RoHS Compliance and Lead Free Relay Information. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/micro/fcai/relays/lead-free-letter.pdf) Lead free solder paste currently used in relays is Sn-3.Ag-.Cu. All signal and most power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). LF is marked on each outer and inner carton. (No marking on individual relays). To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 2,. (Amendment to Directive 2/9/EC) 2. Recommended Lead Free Solder Profile Recommended solder paste Sn-3.Ag-.Cu. Reflow Solder condtion Flow Solder condtion: Pre-heating: maximum C Soldering: dip within sec. at 2 C soler bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 3 C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical realys. 4. Tin Whisker Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test.
Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-, Higashigotanda 2-chome, Shinagawa-ku Tokyo 4, Japan Tel: (-3) 449- Fax: (-3) 449-22 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. E. Caribbean Drive Sunnyvale, CA 99 U.S.A. Tel: (-) 4-49 Fax: (-) 4-49 Email: marcom@fcai.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ Europe Fujitsu Components Europe B.V. Diamantlaan 2 232 WV Hoofddorp Netherlands Tel: (3-23) 9 Fax: (3-23) 9 Email: info@fceu.fujitsu.com Web: http://www.fujitsu.com/emea/services/components/ Asia Pacific Fujitsu Components Asia Ltd. 2E Pasir Panjang Road #4- Citilink Warehouse Complex Singapore 29 Tel: () 3- Fax: () 23-32 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property off their respective owners. Fujitsu Components America does not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. reserves the right to change specifications/datasheets without prior notice. Rev. //.