Product Description is a Premium coloured wood product. It is a relatively high density wood fibre panel engineered to provide colour right throughout. is a natural product and therefore susceptible to or surface discrepancies and colour differences. The fibres have been individually impregnated with organic dyes and chemically bonded using specially designed resins resulting in the following physical and mechanical properties: Features Consistent fibre bonding through depth of sheet 30% stronger than standard MDF Bowing resistant Moisture Resistant Consistent fibre bonding through depth of sheet Scratches are difficult to detect Easy to machine Conforms to standards: AS/NZS 859.:004 Colours: There are eleven standard colours; Black, Blue, Brown, Chocolate, Green, Grey, Light Grey, Orange, Red, Violet, Yellow, Sheet Size: 440mm x 0mm Sheet Thickness: 8mm, mm, 6mm, 9mm, 30mm* * Not available in all colours Formaldehyde E Content: Applications Furniture Acoustic panels Wall cladding Ceilings/partitions Commercial fit-out Tabletops Retail/restaurants/ Bathrooms bars/hotels Storage Modinex panels and boards should be treated with special care, avoid leaning large doors, panels and sheets against walls or other surfaces, this will cause bowing of the product and may void any warranty obligations held by Modinex. Finish Application Guidelines:. Sand the surface to remove any marks caused by industrial sanding and handling (calibration stripes).. Sand edges with fine sanding paper (00grit) to ensure they are sealed with its own dust (this happens when the edge feels almost as smooth as the surface). 3. Apply first coat of sealer being generous on the edges to allow increased absorption. 4. Allow drying time as per manufacturers instructions. 5. Sand all surfaces with fine sand paper (00grit). 6. Apply second coat of sealer as per manufacturers instructions. 7. Allow drying time as per manufacturers instructions 8. Add topcoat to desired gloss level. Care and Maintenance: To remove surface smudges on a good quality finish a simple wipe down with soap and warm water is usually sufficient (care should be taken not to allow moisture to pond on the surface). For more extensive damage caused a furniture polish may be used (this is related to damage to the finish only, and not related to. Refer to manufacturers product data sheet for further details. Product Limitations: predoantly consists of wood fibre and natural dyes. This may result in a range of or inconsistencies, such as colour variation and/or pockets of lighter or darker colour. Standard industry procedure and good work practices are usually sufficient to identify and imise the effect of these inconsistencies during the manufacturing process. Because is predoantly a natural product it may slightly vary in colour across individual sheets, or from sheet to sheet. Homogeneity of colour between different panels is not covered by warranty. In some cases stripes may be evident due to the manufacturing process. These stripes are generally more proent on one face of the sheet than the other. In this case the reverse side of the sheet should be selected as the visible face. When stacking be sure to place on a flat surface, face to face, this will keep the product in its optimal condition, also be sure not to drag the products across each other as this will cause scratches and damage the surface. Phone 800 56 455 Email sales@urbanline.com.au
Assembly and Finishing Traditional construction methods used for MDF apply. can be finished in polyurethane, oils, varnishes or wax. We recommend utilising Vitrecure VC30 which is a clear UV-cured coating. Application is designed for interior use, such as kitchens, bathrooms, laundries, wardrobes, domestic, restaurants, bars, shopfitting and commercial furniture. This product has been designed with the consumer in d and is a perfect solution for all joinery applications. Product Properties Property Unit 8 6 9 5 30 Density Kg/m 3 850 80 800 790 750 740 Swelling (4 hours) % 0 8 8 7 7 Internal Bond N/mm 0.80 0.80 0.75 0.75 0.75 0.75 Bending Strength N/mm 4 40 38 38 36 36 Modulus of Elasticity N/mm 3400 300 300 300 3000 3000 Swelling After Cyclic Test % 9 6 5 5 5 5 Internal Bond After Cyclic Test N/mm 0.30 0.5 0.0 0.0 0.5 0.5 Level of Formaldehyde mg/00g dry board 8 (Class E) Fire F a 30 (Class D-s, d0) Cyclic Tests, Hydrophobic Test Standard (EN3) Temp (ºC) Hours In the Water 0 70 In the Freezer - a -5 4 In the Oven 70 70 Chemical Composition Chemical Entity Cas No Proportion Fire Tests Early Fire Hazard Indices To As 530.3 Cas No Plantation Soft Wood None >80% Urea Formaldehyde (UF) Resin 90-05-6 <0% Melae Urea Formaldehyde (MUF) Resin 5036-3-9 Decorative Paper None <% Paraffin Wax 800-74- <% Ignitability Index -4 Spread of flame index 5 7 Heat evolved index 4 6 Smoke developed index 3 5 Paraffin Wax 800-74- Phone 800 56 455 Email sales@urbanline.com.au
Two supports Three supports L L L L Multiple supports L L L L L Safety Factor 3 dn/m = kg/m Loading Table or 3 Supports Multiple Supports Thickness (mm) L (m) Maximum Load (dn/m ) IL/300 (dn/m ) Maximum Load (dn/m ) IL/300 (dn/m ) 6 6 9 30 0.3 068 5 49 45 0.4 598 45 700 58 0.5 380 0 446 6 0.6 6 9 307 3 0.3 66 373 649-469 0,4 7 5 485 9 o.5 80 73 948 94 0.6 560 38 655 50 0.3 3780 86 448 060 0.4 356 480 449 0.5 353 77 583 4 0.6 936 97 095 4 0.3 5334 449 634 85 0.4 994 603 3500 757 0.5 9 30 35 38 0.6 33 69 548 4 0.3 43 556 457 69 0,4 6979 39 857 904 0.5 4459 77 53 477 0.6 3090 67 363 846 0.7 65 46 649 55 0.8 79 7 03 345 0.9 36 84 594 36.0 099 9 87 66 3 Phone 800 56 455 Email sales@urbanline.com.au
Cabinet drawers 8mm Velchromat panel with 4mm deep rebates Dadoes 4mm deep 4mm in from ends 3 A Sub-framework. 8mm profile BACK. Stainless steel wood screws 3. Profiled on CNC router BOTTOM DRAWER BOX FRONT 4. Inter-changeable colours as an option. SIDE Stainless steel wood screws 4 DRAWER FRONT OPEN 36. Frame 5.6 mm Specified B Hinges and scew rebated fittings hinged doors. mm profile imum. 90º hinge. mm 8mm Velchromat panel 8mm Velchromat panel with 4mm deep rebates SIDE BACK 69 BOTTOM 90º Hinge CLOSED Dadoes 4mm deep 4mm in from ends 3 Frame Stainless steel wood screws 3 7 36. 5.6 DRAWER BOX FRONT 4 DRAWER FRONT OPEN Frame mm Specified scew fittings 3.5 Door 93º Cabinet door Door edge to ø35 bore edge C. Drawer fitting distance mm 3.5 Door 93º 9 94 C Cabinets 9 A. Cabinet hinges Structural timber battens Structural timber battens. 9mm profile wall 30 30 omat profile anchors. Utilise CNC router to form each component. 3. Glue and screw as required. 00 349 330 9 9mm profile 9 94 9 70 9mm profile r Pull 630 k shelves 00 70 900 9mm profile 550 900 king panel 00 Wall anchors Finger Pull 00 door panel 09 009 00 6mm thick shelves 50 50 00 700 80 9mm Backing panel 700 80 00 00 D. Kitchen drawer cabinet E. Kitchen under-sink cabinet 30mm thick door panel 00 4 FRONT ELEVATION 00 Phone 800 56 455 Email sales@urbanline.com.au SIDE ELEVATION 00 FRONT ELEVATION B. D Shoe Storage Cabinet
Storage cabinet 349 330 9 9 94 9 A Sub-framework. 9mm profile 00. Wall anchors 3. Profiled on CNC router 630 4. Glue and screw as required. 00 00 9mm profile Wall anchors Finger Pull 00 09 009 00 6mm thick shelves 00 00 9mm Backing panel 00 00 30mm thick door panel 00 00 Statement Of Hazardous Nature: B. SIDE ELEVATION In its intact state, this product is not classified as a hazardous substance according to the criteria of Safe Work Australia. Dust from the dry product is classified as a hazardous substance according to the criteria of Safe Work Australia. E Rating as per AS/NZS 859.:004 FRONT ELEVATION Sample Classification: Group Number: Group 3 (In accordance with Specification A.4 of the Building Code of Australia.), Average specific extinction area: 9. m²/kg (Refer to Specification C.0 section 4(c) of the Building Code of Australia.), Notes:. The results of this fire test may be used to directly assess fire hazard, but it should be recognised that a single test method will not provide a full assessment of fire hazard under all fire conditions.. As per Section 9 (n) of AS 5637.:05, the deteration of the group number was based on the AS/NZS 3837:998 test, and was deemed valid in the cone calorimeter for the assignment of National Construction Code (NCC) group number. 5 Phone 800 56 455 Email sales@urbanline.com.au
is an environmental friendly non-toxic substance made from recycled pine wood and mill waste. panels are manufactured using waste wood such as branches and chips from softwood forests. In using waste wood helps to sustain forests and imize carbon emissions given off from felling machinery. s manufacturing plant generates enough boimass to sustain its thermal energy requirements, without burning fossil fuels. Environmental credentials: PEFC ST 00: 03 FSC STD 40-004 V- FSC STD 40-005 V- Also the carcinogenic odourless chemical gas known as formaldehyde which is found in the wood fibre bonding resin used in standard MDF is imal in where a special organic nontoxic wood fibre bonding resin is used allowing Valchomat safe to be used in the manufacture of kids toys. Formaldehyde emissions are within the lowest limit standards for wood based materials. also use the same colour dye used in fabric. This dye is organic and non-toxic. 6 Phone 800 56 455 Email sales@urbanline.com.au