Dual Single-Pole OptoMOS Relays Normally Open & Normally Closed Parameter Rating Units Load Voltage 6 V Load Current 1 A Max On-resistance.4 Ω Features 37V rms Input/Output Isolation Small 8-Pin Package Low Drive Power Requirements (TTL/CMOS Compatible Arc-Free With No Snubbing Circuits No EMI/RFI Generation Machine Insertable, Wave Solderable Surface Mount Version Tape & Reel available Description is a 6V, 1A,.4Ω dual Solid State Relay integrating independent normally open (1-Form-A and normally closed (1-Form-B relays into a single package. It features a superior combination of low on-resistance and enhanced peak load current (A max. handling capability. Approvals UL Recognized Component: File # E7627 CSA Certified Component: Certificate # 117739 EN/IEC 69-1 Certified Component TUV Certificate B 9 7 494 4 Applications Telecommunications Instrumentation Multiplexers Data Acquisition Electronic Switching I/O Subsystems Utility Meters (gas, oil, electric and water Medical Equipment-Patient/Equipment Isolation Security Aerospace Industrial Controls Ordering Information Part # S STR Form-A Description 8-Pin DIP (/Tube 8-Pin Surface Mount (/Tube 8-Pin Surface Mount (/Reel Switching Characteristics of Normally Open Devices Pin Configuration 9% I LOAD % 1 + Control - Normally Closed 2 Control - Normally Closed 3 + Control - Normally Open 4 Control - Normally Open 8 7 6 Normally Closed Normally Open Form-B t on Switching Characteristics of Normally Closed Devices t off I LOAD 9% % t off t on Pb RoHS 2/9/EC e3 DS-- www.clare.com 1
Absolute Maximum Ratings @ 2ºC Parameter Ratings Units Blocking Voltage 6 V P Reverse Input Voltage V Input Control Current ma Peak (ms 1 A Input Power Dissipation 1 mw Total Power Dissipation 2 8 mw Isolation Voltage, Input to Output 37 V rms Operational Temperature -4 to +8 C Storage Temperature -4 to +12 C 1 Derate Linearly 1.33 mw/ C 2 Derate Linearly 6.67 mw/ C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Electrical Characteristics @ 2ºC Parameter Conditions Symbol Min Typ Max Units Characteristics: Form-A (Normally Open Load Current Continuous - I L - - 1 Peak t < ms I LPK - - A On-resistance I L =1A R ON -.21.4 Ω Off-State Leakage Current V L =6V I LEAK - - 1 μa Output Capacitance V, f=1mhz C OUT - - pf Switching Speeds Turn-On t =ma, V L =V ON -.7 Turn-Off t OFF -.9 ms Input Control Current I L =1A - - 2 ma Input Dropout Current -.1 - - ma Characteristics: Form-B (Normally Closed Load Current Continuous - I L - -. Peak t < ms I LPK - - 1.2 A On-resistance I L =.A R ON - 1.63 2 Ω Off-State Leakage Current V L =6V, =ma I LEAK - - 1 μa Output Capacitance =ma, V, f=1mhz C OUT - 28 - pf Switching Speeds Turn-On t =ma, V L =V ON -.8 Turn-Off t OFF -.76 ms Input Control Current - - - 2 ma Input Dropout Current I L =.A.1 - - ma Common Characteristics: Form-A and Form-B Input Voltage Drop =ma V F.9 1.2 1.4 V Reverse Input Current V R =V I R - - μa Capacitance, Input to Output - C I/O - 3 - pf *NOTE: If both poles operate simultaneously load current must be derated so as not to exceed the package power dissipation value. 2 www.clare.com
PERFORMANCE DATA* 3 1-Form-A & s Typical LED Forward Voltage Drop (N=, T A =2ºC, =ma 2 Typical On-Resistance (N=, T A =2ºC, I L =1A, =ma Typical On-Resistance (N=, T A =2ºC, I L =ma, 2 1 1 1 1.2 1.22 1.23 1.23 1.24 1.24 LED Forward Voltage Drop (V.6.7.8.9.2.211 On-Resistance (Ω 1.49 1.3 1.7 1.61 1.6 1.69 On-Resistance (Ω Typical Blocking Voltage (N=, T A =2ºC Typical Blocking Voltage (N=, T A =2ºC, =ma Typical (N=, T A =2ºC, I L 1 1 1 6. 66. 66. 67. 67. 68. 7 76 77 78 79 8.6.69.73.77.81.8 LED Forward Current (ma 2 Typical (N=, T A =2ºC, I L 2 Typical Turn-On Time (N=, T A =2ºC, I L =ma, =ma Typical Turn-Off Time (N=, T A =2ºC, I L =ma, =ma 1 1 1.16.17.18.19..21 LED Forward Current (ma.7.61.6.69.73.77 Turn-Off Time (ms.77.82.87.92.97.2 Turn-On Time (ms Typical Turn-On Time (N=, T A =2ºC, I L =ma, =ma 2 Typical Turn-Off Time (N=, T A =2ºC, I L =ma, =ma 1 1.7.3.3.76.99.622 Turn-On Time (ms.63.67.71.7.79.83 Turn-Off Time (ms *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. www.clare.com 3
PERFORMANCE DATA* Load Current (A 1.2 1..8.6.4.2 Form-A Relay Typical Load Current vs. Temperature ( =ma Leakage Current (na 1 Typical Leakage vs. Temperature Measured Across Pins & 6 (V L =6V Typical Blocking Voltage vs. Temperature 7 69 68 67 66 6 64 63. -4-4 6 8 Temperature (ºC -4-4 6 8 Temperature (ºC 62-4 - 4 6 8 Temperature (ºC 2. Typical Turn-On vs. Temperature =ma 9 Typical Turn-Off vs. Temperature =ma Typical Turn-On vs. LED Forward Current =ma Turn On Time (ms 2. 1. 1. =ma Turn Off Time (μs 8 8 7 7 6 6 =ma Turn-On (μs 8 6 4. -4-4 6 8 Temperature (ºC -4-4 6 8 Temperature (ºC 3 4 LED Forward Current (ma Turn-Off Time (μs Typical Turn-Off vs. LED Forward Current =ma 77.8 77.7 77.6 77. 77.4 77.3 77.2 77.1 3 4 LED Forward Current (ma AC On-Resistance (Ω.26.24.22..18.16.14 Typical On-Resistance (AC vs. Temperature =ma, =ma.12-4 - 4 6 8 Temperature (ºC LED Current (ma.9.9.8.8.7 Typical vs. Temperature.7-4 - 4 6 8 Temperature (ºC Typical Load Current vs. Load Voltage (T A =2ºC, =ma 1. 6 Energy Rating Curve Current (A.. -. Load Current (A 4 3 2 1-1. -. -.1 -. -.....1. Voltage (V μs μs 1ms ms ms 1s s s Time *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.clare.com
PERFORMANCE DATA*.6 Form-B Relay Typical Load Current vs. Temperature ( 3 Typical Leakage vs.temperature Measured Across Pins 7&8 ( =ma, V L =6V Typical Blocking Voltage vs. Temperature ( =ma 94 Load Current (A..4.3.2.1 Leakage Current (na 3 92 9 88 86 84 82. -4-4 6 8 Temperature (ºC -4-4 6 8 Temperature (ºC 8-4 - 4 6 8 Temperature (ºC Turn-On Time (μs Turn-Off Time (ms 8 7 6 4 3 Typical Turn-On vs. Temperature =ma =ma -4-4 6 8 Temperature (ºC Typical Turn-Off vs. LED Forward Current =ma 2. 2. 1. 1.. 3 4 LED Forward Current (ma Turn-Off Time (ms On-Resistance (Ω Typical Turn-Off vs. Temperature =ma 4. 4. 3. I 3. F 2. 2. 1. =ma 1.. -4-4 6 8 Temperature (ºC Typical On-Resistance vs. Temperature =ma, 1.8 1.7 1.6 1. 1.4 1.3 1.2 1.1-4 - 4 6 8 Temperature (ºC Turn-On Time (μs LED Current (ma 1-Form-B Typical Turn-On vs. LED Forward Current =ma 423 422 421 4 419 418 417.4.3.3.2..1 3 4 LED Forward Current (ma Typical vs. Temperature =ma. -4-4 6 8 Temperature (ºC.6 Typical Load Voltage vs. Load Current (T A =2ºC, 1. Energy Rating Curve Current (A.4.2. -.2 -.4 Load Current (A 1.3 1.1.9.7. -.6-1. -.8 -. -.3..3..8 1. Voltage (V.3 μs μs 1ms ms ms 1s s s Time *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. www.clare.com
Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. Clare classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product is rated Moisture Sensitivity Level 1 (MSL 1, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-33. ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-62. Reflow Profile This product has a maximum body temperature rating of ºC for a maximum of 3 seconds. All other guidelines of J-STD- must be observed. Board Wash Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorinebased solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb RoHS 2/9/EC e3 6 www.clare.com
Mechanical Dimensions 2.4 ±.127 (. ±. 6.3 ±.127 (. ±..47 ±.76 (.18 ±.3 4.64 TYP (.16 9.62 ±.381 (.38 ±.1 3.32 ±.1 (.13 ±.2 7.6 ±.24 (.3 ±. 9.144 ±.8 (.36 ±. 7.239 TYP. (.28.24 TYP (.1 8-.8 DIA. (8-.31 DIA. 6.3 ±.127 (. ±. 7.6 ±.127 (.3 ±. PCB Hole Pattern 2.4 ±.127 (. ±. 7.6 ±.127 (.3 ±..889 ±.2 (.3 ±.4 Dimensions mm (inches 2.4 ±.127 (. ±. 9.62 ±.381 (.38 ±.1 3.32 ±.1 (.13 ±.2.63 ±.127 (.2 ±. PCB Land Pattern 2.4 (. 6.3 ±.127 (. ±. 4.44 ±.127 (.17 ±. 9.2 ±.24 (.37 ±. 7.6 ±.24 (.3 ±..47 ±.76 (.18 ±.3.24 ±.127 (. ±. 1.6 (.649.6 (.2 8.9 (.33.813 ±.1 (.32 ±.4 Dimensions mm (inches 33.2 DIA. (13. DIA. Top Cover Tape Thickness.2 MAX. (.4 MAX. Bo=.3 (.46 W=16. (.63 Embossed Carrier Embossment K =4.9 (.193 K 1 =4. (.16 Ao=.3 (.46 P=12. (.472 User Direction of Feed Dimensions mm (inches NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all Notes for constant dimensions listed on page of EIA-481-2 For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. 7 Specification: DS-- Copyright, Clare, Inc. OptoMOS is a registered trademark of Clare, Inc. All rights reserved. Printed in USA. 6/7/