~ AUX
SPECIFICATI MODEL OUTPUT INPUT OTHERS NOTE LCM-0UDA- Current level selectable via DIP switch, please refer to DIP SWITCH TABLE section CURRENT LEVEL 50mA 500mA 600mA 700mA(default) 900mA 050mA RATED POWER 5W DC VOLTAGE RANGE ~ 00V ~ 70V ~ 59V ~ 50V ~ 9V ~ V OPEN CIRCUIT VOLTAGE (max.) 0V 65V CURRENT RIPPLE Note.6 5.0% max. @rated current CURRENT TOLERANCE ±5% AUXILIARY DC OUTPUT Nominal V(deviation.~.6V)@50mA for AUX-Type only SETUP TIME Note. 000ms / 5VAC VOLTAGE RANGE Note. 90 ~ VAC 7 ~ 86VDC (Please refer to "STATIC CHARACTERISTIC" section) FREQUENCY RANGE POWER FACTOR (Typ.) TOTAL HARMIC DISTORTI EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) MTBF DIMENSI PACKING Note. 7 ~ 6Hz 87.5% MAX. No. of PSUs on 6A CIRCUIT BREAKER units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 5VAC LEAKAGE CURRENT <0.5mA / 0VAC SHORT CIRCUIT Constant current limiting, recovers automatically after fault condition is removed PROTECTI OVER VOLTAGE 0 ~ 0V Shutdown o/p voltage, re-power on to recover OVER TEMPERATURE Shutdown o/p voltage,re-power on to recover DIMMING Please refer to "DIMMING OPERATI" section FUNCTI SYNCHRIZATI Please refer to "SYNCHRIZATI OPERATI section TEMP. COMPENSATI By external NTC, please refer to TEMPERATURE COMPENSATI OPERATI section WORKING TEMP. Tcase=-0 ~ 90 (Please refer to OUTPUT LOAD vs TEMPERATURE section) MAX. CASE TEMP. Tcase=90 ENVIRMENT WORKING HUMIDITY 0 ~ 90% RH non-condensing STORAGE TEMP., HUMIDITY -0 ~, 0 ~ 95% RH TEMP. COEFFICIENT VIBRATI ±0.0%/ (0 ~ 50 ) 0 ~ 500Hz, G 0min./cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS DALI STANDARDS UL8750 approved Comply with IEC686-0, 0, 07 SAFETY & WITHSTAND VOLTAGE I/P-O/P:.75KVAC EMC ISOLATI RESISTANCE I/P-O/P:>00M Ohms / 500VDC / 5 / 70% RH EMC EMISSI PF 0.98/5VAC @ full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) THD< 0%(@load 75%) (Please refer to TOTAL HARMIC DISTORTI(THD) section) 0.A/5VAC COLD START 5A(t width=70μ s measured at 50% I peak) at 5VAC; Per NEMA 0 Compliance to FCC part 5 Subpart B 9.6K hrs min. MIL-HDBK-7F (5 ).5*8.5*mm (L*W*H) 0.8Kg ; 5pcs/6Kg/.CUFT
BLOCK DIAGRAM PFC fosc : 60KHz PWM fosc : KHz RECTIFIERS Vaux (optional) I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING RECTIFIERS & FILTER CURRENT LIMIT MCU V -V DA DA- PFC CTROL O.L.P. O.T.P. PWM CTROL O.V.P. DETECTI CIRCUIT DIP SWITCH TABLE LCM-0UDA is a multiple-stage constant current driver, selection of output current through DIP switch is exhibited below. Io DIP S.W. 5 6 50mA 500mA 600mA 700mA(factory default) 900mA 050mA
DIMMING OPERATI LCM-0UDA DA- DA PUSH AC/N AC/L Push Button AC/N AC/L PUSH dimming(primary side) Action Action duration Function Short push 0.~ sec. Turn -OFF the driver Long push.5~0 sec. Every Long Push changes the dimming direction, dimming up or down Reset > sec. Set up the dimming level to 00% The factory default dimming level is at 00%. If the push action lasts less than 0.05 sec., it will not lead to a change for the status of the driver. Up to 0 drivers can perform the PUSH dimming at the same time when utilizing one common push button. The maximum length of the cable from the push button to the last driver is 0 meters. The additive push button can be connected only between the PUSH terminal, as displayed in the diagram, and AC/L (in brown or black); it will lead to short circuit if it is connected to AC/N. DALI interface(primary side) Apply DALI signal between DA and DA- DALI protocol comprises 6 groups and 6 addresses. First step is fixed at 6% of output.
SYNCHRIZATI OPERATI Synchronization up to 0 drivers ( master 9 slaves) Dimming operating range : 0%~00% Sync cable length : < 5m Sync cable type : Flat cable Sync cable cross section area : AWG (0.~0.mm ) LCM-0UDA (Slave ) SYN. SYN. SYN. LCM-0UDA LCM-0UDA - - (Master) - - (Slave ) - - 5m 5m NOTE:. Please make sure all units are set to 00% dimming setting (factory default) before synchronizing.. Min. Dimming operating range depends on dimmer setting. TEMPERATURE COMPENSATI OPERATI LCM-0UDA have the built-in temperature compensation function ; by connecting a temperature sensor (NTC resistor) between the NTC / -NTC terminal of LCM-0UDA and the detecting point on the lighting system or the surrounding environment, output current of LCM-0UDA could be correspondingly changed, based on the sensed temperature, to ensure the long life of LED. 05 NTC derating curve Output Current (%) 00 95 90 85 75 70 0KΩ 0KO 0KΩ 0KO 70KΩ 70KO 65 55 60 65 70 75 85 90 95 Sensed Temperature( ) LCM-0UDA can still be operated normally when the NTC resistor is not connected and the value of output current will be the current level selected through the DIP switch. NTC reference: NTC resistance 0K 0K 70K Output Current < 60, 00% of the rated current (corresponds to the setting current level) > 60, output current begins to reduce, please refer to the curve for details. < 70, 00% of the rated current (corresponds to the setting current level) > 70, output current begins to reduce, please refer to the curve for details. <, 00% of the rated current (corresponds to the setting current level) >, output current begins to reduce, please refer to the curve for details. Notes:. MEAN WELL does not offer the NTC resistor and all the data above are measured by using THINKING TTC0 series.. If other brands of NTC resistor is applied,please check the temperature curve first. Dimming and synchronization function of the driver will be invalid when the "temperature compensation" function is in use.
OUTPUT LOAD vs TEMPERATURE 00 Others 00 60 900mA 60 LOAD (%) 0 0 050mA LOAD (%) 0 0-0 -5 0 5 0 0 5 50 55 60 70 (HORIZTAL) AMBIENT TEMPERATURE,Ta ( ) -0-5 0 0 5 55 65 75 90 Tcase ( ) (HORIZTAL) STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 00 Constant Current Mode 90 0.99 0.98 0.97 050 70 0.96 900 LOAD (%) 60 50 0 PF 0.95 0.9 0.9 0.9 0.9 PF 700 600 500 50 90 95 00 05 0 5 0 5 INPUT VOLTAGE (V) 60Hz 0.9 0% 0% 0% 0% 50% 60% 70% % 90% 00% De-rating is needed under low input voltage. LOAD (5Vac Input) TOTAL HARMIC DISTORTI (THD) Tcase at EFFICIENCY vs LOAD possess superior working efficiency that up to 87.5% can be reached in field applications. Tcase at 0.0% 90.0% 85.0% THD 5.0% 0.0% 5.0% 0.0% 5.0% 0% 0% 0% 0% 50% 60% 70% % 90% 00% 050 900 700 600 500 50 EFFICIENCY(%).0% 75.0% 70.0% 65.0% 60.0% 55.0% 50.0% 5.0% 0.0% 050 900 700 600 500 50 LOAD (5Vac Input) 0% 0% 0% 0% 50% 60% 70% % 90% 00% LOAD (5Vac Input)
MECHANICAL SPECIFICATI Case No.LCM-60A Unit:mm.5 0 -ψ. 5 TB 8.5 68 TB SYN. CN0 CN00 TB5 5 6 9. 65.5 7.8 7.8 -ψ 5 tc 0 tc Bottom View : Max. Case Temperature Terminal Pin No. Assignment( TB) Pin No. Assignment Pin No. AC/L AC/N 5 PUSH Assignment DA DA- Terminal Pin No. Assignment( TB) Pin No. Assignment Pin No. FAN(optional) -FAN(optional) Assignment NTC -NTC Pin(FAN) / Pin(-FAN) is the Auxiliary DC output for the optional model LCM-0UDA-AUX; it can be used to drive fan. Terminal Pin No. Assignment( TB5) Pin No. Assignment V -V SYN. Connector(CN0/CN00):JST BB-XH or equivalent Pin No. Assignment Mating Housing Terminal,, - JST XHP or equivalent JST SXH-00T-P0.6 or equivalent