oad cell Overview Combined error comb Repeatability v ±0.0% C n ±0.0% C n The shear beam load cell is particularly suitable for implementation in container, overhead rail conveyor and platform scales. esign The measuring element is a shear tension spring made of stainless steel to which strain gauges are applied. The strain gauges are arranged at 4 to the longitudinal axis on the side of the spring body and are therefore subject to shear forces. Under the influence of the load acting in the measuring direction, the spring bodies and therefore the friction-locked strain gauges are elastically deformed. This generates a measuring signal voltage that is proportional to the load. Technical specifications 1 Possible applications odel oads /maximum load max. inimum initial loading min ax. working load u opper scales Conveyor belt scales Overhead rail scales Platform scales Shear beam load cell 0. t (0.49 tn..) 1 t (0.98 tn..) t (1.97 tn..) t (4.9 tn..) 0kg 10% max. Creep error cr 0 min ± 0.0% C n Temperature coefficient Zero signal T o 0.0% C n / Characteristic value T c 0.017% C n / lectrical characteristic values Recommended reference voltage U ref... 1 V C Input resistance R e 1000 ± 10 Output resistance R a 1004 ± Insulation resistance R is 000 at 0 V C Connection and environmental conditions Rated temperature range tn -10...+40 C(14...104 ) Operating temperature range tu -...+6 C(-1...+149 ) Storage temperature range ts -...+6 C(-1...+149 ) Sensor material (IN) Stainless steel egree of protection according to IP68 N 609; IC 609 Recommended tightening torque of the fixing screws max = 0., 1, t 10 Nm 1) max = t 0 Nm 1) Cable connection unction Color XC + Green XC- lack SIG + White SIG - Red Shield Transparent Certificates and approvals ccuracy class according to C OI R60 reak load d Safe lateral load Iq easurement characteristic values 00% max. 100% max Rated measuring path h n at max. max = 00 kg (0.49 tn..) 0.1 mm (0.00 in) max = 1t (0.98tn..) 0.1 mm (0.008 in) max = t (1.97tn..) 0.9 mm (0.011 in) max = t (4.9tn..) 0.8 mm (0.014 in) Rated characteristic value C n.0 ± 0.00 mv/v Tolerance o of zero signal ±1.0% C n ax. load cell verification intervals 000 n C in. load cell verification intervals V min max = 00 kg (0.49 tn..) max /10 000 max = 1,, t (0.98, 1.97, max /1 000 4.9 tn..) inimum application range R min(c) max = 00 kg (0.49 tn..) 0% max = 1,, t (0.98, 1.97, 0% 4.9 tn..) 1) The tightening torque is to be selected according to the strength class of the screws. / Siemens WT 10 018
oad cell Selection and ordering data rticle No. imensional drawings oad cells type W0 S-S S egal-for-trade acc. to OI R60 up to 000d, connecting cable m (9.84 ft) at 00 kg (1 10.1 lb) up to 1 t (0.98 tn..),connecting cable 6 m (19.68 ft) at t (1.97 tn..) up to t (4.9 tn..) 7107-0.8 (0.11) ØG Ø. (0.1) Click on the rticle No. for the online configuration in the PI ife Cycle Portal. 00 kg (1 10.1 lb) 1t(0.98tn..) t(1.97tn..) t(4.9tn..) P 4 4 G 4 P Ø xplosion protection Without 0 xplosion protection for zones 0, 1,, 0, 1, 1 C C Ø 0. 1 10 (.1) 10 (.1) 10 (.1) 17 (6.77) 16 (0.6) 16 (0.6) 16 (0.6) 19 (0.6).4 (1.00).4 (1.00).4 (1.00) 8.1 (1.0) (.99) (.99) (.99) 9 (.74) (1.6) (1.6) (1.6) 8 (1.0) 1 (0.1) 1 (0.1) 1 (0.1) 0. ØG 0. 1 0. 0. 0. 0. (1.89) 14 (0.) 14 (0.) 14 (0.) 0 (0.79) 6 (1.0) 8 (1.10) (1.6) 40 (1.7) (1.6) (1.6) 6 (1.4) 44 (1.7) 7 (.4) 7 (.4) 7 (.4) (.99) 1 1 1 0 load cell, dimensions in mm (inch) Siemens WT 10 018 /
ounting unit Overview The self-aligning mounting unit for load cells is particularly suitable for implementation in container, platform and roller table scales. Technical specifications ounting unit for load cells of the series 0., 1, t (0.49, 0.98, t (4.9 tn..) 1.97 tn. ) aximum lateral deflection ± mm (0.1 inch) ± mm (0.1 inch) with load cell ifting path of the top mm (0.1 inch) mm (0.1 inch) plate Restoring force per millimeter 1 %/mm 10%/mm of lateral deflection of the top plate in % of the applied load with load cell Permitted supporting load with fixed top plate kn kn Permitted lifting force on kn 0 kn the top plate Permitted transverse force on the top plate with fixed top plate kn kn esign Selection and ordering data 1 The mounting unit comprises a base plate and a top plate, a selfaligning bolt and two countersunk screws. ounting units The top plate is aligned and fixed above the base plate with the two countersunk screws. This results in a stable unit. The height of the top plate is adjusted so that it is three millimeters above the installation height with load cell. In this state the mounting unit serves as an installation aid and can be used as a dummy for light installation jobs. 00 kg (1 10.1 lb), 1 t (0.98 tn..) Prior to installation, the load cell is inserted with the self-aligning t (1.97 tn..) bolt into the mounting unit. Then the complete unit is installed in t (4.9 tn..) the scales. s the result, the load bearing implement and the installation units are aligned. The load cells are not yet loaded. Shims (accessories) inally the load bearing implement is lowered by undoing two hex nuts under the top plate. The weight now rests on the load cells. aterial: Stainless steel or load cells with a rated load of In this state the load cell and the pressure pieces together form 1)) a self-centering unit. The mounting unit permits sideways displacement of the top plate, and hence of the load bearing imple- Contents: 16 units, each 0. mm thick 00 kg, 1 t, t (0.49, 0.98, 1.97 tn. ) ment, by up to three millimeters. or load cells of the series aterial: Stainless steel or load cells with a rated load of: 1)) Click on the rticle No. for the online configuration in the PI ife Cycle Portal. or mounting units of the series t (4.9 tn. ) Contents: 4 units each 0. mm thick, 16 units each 1 mm thick rticle No. G P 7707-4 0 0 771- G00 771-4PG00 1) ) The load cell is not included in the scope of delivery. It is highly recommendable to use a grounding cable (7701-11) in order to protect the load cell. /4 Siemens WT 10 018
ounting unit imensional drawings I C ØG (6x) C 0,... 80 (.1) 10 (4.1).4 (0.88) 1.6 (1.4) 1 (0.9) 0 (0.79) (.99) 108 (4.) 1 (0.9) (0.98) 60 (.6) 80 (.1) 0,... ØG 11 (4.) 1. (0.) 10 (4.7) 10 (.91) I 80 (.14) 100 (.94) 90 (.4) 110 (4.) 110 (4.) 14 (.71) 1 (0.9) 0 (0.79) s 140 (.1) (0.1) 18 (7.8) (0.1) G_WT01_XX_1009 ounting unit for load cells, dimensions in mm (inch) Siemens WT 10 018 /
ase plate with elastomer bearing Overview esign lastomer bearings are rubber-metal composites made of neoprene and stainless steel. Their special design means that lateral movement of the load bearing implement does not result in high transverse force on the load cell. If the load bearing implement is displaced by more than 4 mm (0.16 inch) in the horizontal direction, measures for restricting sideways play (e.g. stops) must be provided in the construction of the load bearing implement. The base plate of stainless steel is used for suitable fixing of the load cell on the base. The load cell is not included in the scope of delivery of the base plate or elastomer bearing. The base plate and the elastomer bearing form a self-centering bearing unit together with the load cells of the series. It suppresses oscillations and shocks to a certain extent. Selection and ordering data ase plate or load cells of the series aterial: Stainless steel or load cells with a rated load of: 1)) Click on the rticle No. for the online configuration in the PI ife Cycle Portal. 0, 1t (0.49 0.98tn.) t (1.97tn.) t (4.9tn.) lastomer bearings or load cells of the series aterial: neoprene, stainless steel or load cells with a rated load of: 1)) 0, 1t (0.49 0.98tn.) t (1.97tn.) t (4.9tn.) rticle No. 7707-4 0 0 G P C G C P C Technical specifications 1 ase plate with elastomer bearing for load cells 00 kg (0.49 tn..) 1t (0.98tn..) t (1.97tn..) t (4.9 tn..) aximum permitted lateral ± 4 mm (0.16 in) ± 4 mm (0.16 in) ± 4 mm (0.16 in) ± 4 mm (0.16 in) deflection Vertical rigidity.9 kn/mm.9 kn/mm 9.98 kn/mm 9.98 kn/mm orizontal rigidity 0.16 kn/mm 0.16 kn/mm 0.4 kn/mm 0.4 kn/mm Compression at rated load 0.68 mm (0.07 in) 1.8 mm (0.00 in) 0.6 mm (0.04 in) 1.46 mm (0.07 in) 1) ) The load cell is not included in the scope of delivery. It is highly recommendable to use a grounding cable (7701-11) in order to protect the load cell. /6 Siemens WT 10 018
ase plate with elastomer bearing imensional drawings 0 (1.97) 6 (0.4) ØC N Ø11 (0.4) Ø G Rated load øc G 0,, 1 100 (.94) 7 (.9) 8 (.) 140 (.1) 10 (4.7) 1 (0.9) 110 (4.) 10 (4.7) 90 (.4) 100 (.94) 140 (.1) 10 (4.7) 1 (0.9) 110 (4.) 10 (4.7) 90 (.4) 100 (.94) 18 (7.8) 10 (.91) 0 (0.79) 14 (.71) Rated load 0,, 1 90 (.4) 90 (.4) 110 (4.) ø 11 (0.4) 11 (0.4) 1. (0.) 1 (0.9) 1 (0.9) (0.98) 47 (1.8) 1 (.01) 69 (.7) N 117.4 (4.6) 108 (4.) 117.4 (4.6) 11 (4.41) 1.1 (6.0) 14 (.8) G_WT01_XX_101 ase plate with elastomer bearing for load cells, dimensions in mm (inch) Siemens WT 10 018 /7