High Performance Schottky Rectifier, 16 D 2 PK ase cathode 2 1 3 N/C node PRODUCT SUMMRY Package TO-263 (D 2 PK) I F(V) 16 V R 35 V, 45 V V F at I F.63 I RM 4 m at 125 C T J max. 15 C Diode variation Single die E S 24 mj FETURES 15 C T J operation High frequency operation Low forward voltage drop High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance Guard ring for enhanced ruggedness and long term reliability Meets MSL level 1, per J-STD-2, LF maximum peak of 26 C EC-Q1 qualified Material categorization: for definitions of compliance please see /doc?99912 DESCRIPTION This VS-MR16... Schottky rectifier has been optimized for low reverse leakage at high temperature. The proprietary barrier technology allows for reliable operation up to 15 C junction temperature. Typical applications are in switching power supplies, converters, freewheeling diodes, and reverse battery protection. MJOR RTINGS ND CHRCTERISTICS SYMOL CHRCTERISTICS VLUES UNITS I F(V) Rectangular waveform 16 V RRM 35/45 V I FSM t p = 5 μs sine 18 V F 16 pk, T J = 125 C.57 V T J -65 to +15 C VOLTGE RTINGS PRMETER SYMOL VS-MR1635PbF VS-MR1645PbF UNITS Maximum DC reverse voltage V R Maximum working peak reverse voltage V RWM 35 45 V SOLUTE MXIMUM RTINGS PRMETER SYMOL TEST CONDITIONS VLUES UNITS Maximum average forward current I F(V) T C = 134 C, rated V R 16 Following any rated Non-repetitive peak surge current I FSM rated V RRM applied 5 μs sine or 3 μs rect. pulse load condition and with 18 Surge applied at rated load condition half wave single phase 6 Hz 15 Non-repetitive avalanche energy E S, I S = 3.6, L = 3.7 mh 24 mj Current decaying linearly to zero in 1 μs Repetitive avalanche current I R Frequency limited by T J maximum V = 1.5 x V R typical 3.6 Revision: 18-Oct-16 1 Document Number: 9434 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T /doc?9
ELECTRICL SPECIFICTIONS PRMETER SYMOL TEST CONDITIONS VLUES UNITS Maximum forward voltage drop V FM (1) 16 Note (1) Pulse width < 3 μs, duty cycle < 2 %.63 T J = 125 C.57 Maximum instantaneous.2 I RM reverse current Rated DC voltage T J = 125 C 4 m Maximum junction capacitance C T V R = 5 V DC (test signal range khz to 1 MHz), 25 C 14 pf Typical series inductance L S Measured lead from top of terminal to mounting plane 8. nh Maximum voltage rate of change dv/dt Rated V R V/μs V THERML - MECHNICL SPECIFICTIONS PRMETER SYMOL TEST CONDITIONS VLUES UNITS Maximum junction temperature range T J -65 to +15 Maximum storage temperature range T Stg -65 to +175 C Maximum thermal resistance, junction to case R thjc DC operation 1.5 Typical thermal resistance, case to heatsink R thcs Mounting surface, smooth and greased.5 C/W pproximate weight 2 g.7 oz. minimum 6 (5) kgf cm Mounting torque maximum 12 () (lbf in) Marking device Case style D 2 PK MR1635 Revision: 18-Oct-16 2 Document Number: 9434 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T /doc?9
I F - Instantaneous Forward Current () 1 T J = 15 C T J = 125 C.2.4.6.8 1. 1.2 V FM - Forward Voltage Drop (V) Fig. 1 - Maximum Forward Voltage Drop Characteristics I R - Reverse Current (m) 1..1.1.1.1 T J = 15 C T J = C T J = 5 C T J = 125 C T J = 75 C 5 15 2 25 3 35 4 45 V R - Reverse Voltage (V) Fig. 2 - Typical Values of Reverse Current vs. Reverse Voltage C T - Junction Capacitance (pf) 2 3 4 5 V R - Reverse Voltage (V) Fig. 3 - Typical Junction Capacitance vs. Reverse Voltage Z thjc - Thermal Impedance ( C/W) 1.1.1 Single pulse (thermal resistance) D =.75 D =.5 D =.33 D =.25 D =.2.1.1.1.1.1.1 1 t 1 - Rectangular Pulse Duration (s) Fig. 4 - Maximum Thermal Impedance Z thjc Characteristics P DM Notes: 1. Duty factor D = t 1 /t 2 2. Peak T J = P DM x Z thjc + T C t 1 t 2 Revision: 18-Oct-16 3 Document Number: 9434 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T /doc?9
155 15 llowable Case Temperature ( C) 15 145 14 135 13 125 12 Square wave (D =.5) Rated V R applied See note (1) DC 5 15 2 25 verage Power Loss (W) 5 RMS limit DC D =.75 D =.5 D =.33 D =.25 D =.2 5 15 2 25 I F(V) - verage Forward Current () I F(V) - verage Forward Current () Fig. 5 - Maximum llowable Case Temperature vs. verage Forward Current Fig. 6 - Forward Power Loss Characteristics I FSM - Non-Repetitive Surge Current () t any rated load condition and with rated V RRM applied following surge t p - Square Wave Pulse Duration (µs) Fig. 7 - Maximum Non-Repetitive Surge Current (Per Leg) L D.U.T. IRFP46 High-speed switch Current monitor R g = 25 Ω Freewheel diode 4HFL4S2 + V d = 25 V Fig. 8 - Unclamped Inductive Test Circuit Note (1) Formula used: T C = T J - (Pd + Pd REV ) x R thjc ; Pd = forward power loss = I F(V) x V FM at (I F(V) /D) (see fig. 6); Pd REV = inverse power loss = V R1 x I R (1 - D); I R at V R1 = rated V R applied Revision: 18-Oct-16 4 Document Number: 9434 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T /doc?9
ORDERING INFORMTION TLE Device code VS- MR 16 45 TRL PbF 1 2 3 4 5 6 7 1 - product 2 - Essential part number 3 - = surface mount 4 - Current rating (16 = 16 ) 5 - Voltage code = V RRM 6 - None = tube (5 pieces) TRL = tape and reel (left oriented) TRR = tape and reel (right oriented) 7 - PbF = lead (Pb)-free 35 = 35 V 45 = 45 V ORDERING INFORMTION PREFERRED P/N QUNTITY PER T/R MINIMUM ORDER QUNTITY PCKGING DESCRIPTION VS-MR1635PbF 5 ntistatic plastic tubes VS-MR1635TRRPbF 8 8 13" diameter reel VS-MR1635TRLPbF 8 8 13" diameter reel VS-MR1645PbF 5 ntistatic plastic tubes VS-MR1645TRRPbF 8 8 13" diameter reel VS-MR1645TRLPbF 8 8 13" diameter reel LINKS TO RELTED DOCUMENTS Dimensions Part marking information Packaging information SPICE model /doc?9546 /doc?9554 /doc?9532 /doc?9547 Revision: 18-Oct-16 5 Document Number: 9434 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T /doc?9
DIMENSIONS in millimeters and inches D 2 PK Outline Dimensions Conforms to JEDEC outline D 2 PK (SMD-22) (3) L1 (2)(3) E 4 c2 (E) (D1) (3) Pad layout 11. (.43) 9.65 (.38) D L2 2 x e 1 2 3 H (2) 2 x b2 2 x b C Detail. M M c ±.4 M E1 View - H (3) 17.9 (.7) 15. (.625) 2.32 (.8) Plating 2.64 (.3) 2.41 (.96) (4) b1, b3 3.81 (.15) ase Metal Gauge plane Lead tip to 8 L3 L L4 Detail Rotated 9 CW Scale: 8:1 1 Seating plane (c) (b, b2) Section - and C - C Scale: None c1 (4) SYMOL MILLIMETERS INCHES MILLIMETERS INCHES NOTES SYMOL MX. MX. MX. MX. NOTES 4.6 4.83.16.19 D1 6.86 8..27.315 3 1..254.. E 9.65.67.38.42 2, 3 b.51.99.2.39 E1 7.9 8.8.311.346 3 b1.51.89.2.35 4 e 2.54 SC. SC b2 1.14 1.78.45.7 H 14.61 15.88.575.625 b3 1.14 1.73.45.68 4 L 1.78 2.79.7.1 c.38.74.15.29 L1-1.65 -.66 3 c1.38.58.15.23 4 L2 1.27 1.78.5.7 c2 1.14 1.65.45.65 L3.25 SC. SC D 8.51 9.65.335.38 2 L4 4.78 5.28.188.28 Notes (1) Dimensioning and tolerancing per SME Y14.5 M-1994 (2) Dimension D and E do not include mold flash. Mold flash shall not exceed.127 mm (.5") per side. These dimensions are measured at the outmost extremes of the plastic body (3) Thermal pad contour optional within dimension E, L1, D1 and E1 (4) Dimension b1 and c1 apply to base metal only (5) Datum and to be determined at datum plane H (6) Controlling dimension: inch (7) Outline conforms to JEDEC outline TO-263 Revision: 8-Jul-15 1 Document Number: 9546 For technical questions within your region: Diodesmericas@vishay.com, Diodessia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUJECT TO CHNGE WITHOUT NOTICE. THE PRODUCTS DESCRIED HEREIN ND THIS DOCUMENT RE SUJECT TO SPECIFIC DISCLIMERS, SET FORTH T /doc?9
Legal Disclaimer Notice Vishay Disclaimer LL PRODUCT, PRODUCT SPECIFICTIONS ND DT RE SUJECT TO CHNGE WITHOUT NOTICE TO IMPROVE RELIILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. ll operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Revision: 13-Jun-16 1 Document Number: 9