e Shelving Technical Manual v.9.17
Components Components 0.375 (10mm) 0.718 (18mm) wall standard 1.25 (32mm) 1.25 (32mm) shelf bracket 0.312 (8mm) fascia (optional) Finish Options Anodized Powder Coat Contact Element Designs for availability of additional finishes. natural aluminum (N) onyx () (X) oil rubbed bronze (ORB) 2 v. 9.18
Components Design Guidelines Wall Standard Lengths: 24, 48, 72, 96 Arm Bracket Depths: 10, 12 Custom wall standard lengths available up to 120 Custom bracket depths available up to 18 Recommended max. of 30 spacing between wall standard installation. Arm bracket easily installed at any point on wall standard with 1/8 allen wrench Shelf bracket mounting allows for a variety of shelf construction styles. (Shelves pictured not provided by Element Designs.) Fascia allows for ability to attach custom moulding. (Not provided by Element Designs.) Arm brackets on both sides of wall standard allows use of different shelf thicknesses and additional load capacity. 3 v. 9.18
Wall Standard Drilling Standard hole locations will be 4 from top and bottom, with middle holes spaced between evenly on center 4 v. 9.18
Glass Shelf Options Backpainted Glass - Available in 6mm, 10mm, 12mm white sand mocha scarlet black slate white sand mocha scarlet black slate silver bronze olive custom color elusion black BPG with grey glass elusion white BPG with low-iron satin Elusion glass will have 1 1/2 backpainted border Elusion border color available in silver bronze olive non-standard color all standard and custom colors. Standard Glass - Available in 6mm low-iron low-iron satin satin grey (smoked) grey reflective Standard Glass - Available in 10mm & 12mm bronze bronze reflective All Backpainted glass will have a light grey backer, unless otherwise specified Printed color swatches may not be an exact color representation Please order a physical sample for color accuracy. Please refer to Element Designs Catalog for all Non-Standard Color options Additional custom and metallic colors also available. Contact Element Designs for color options. All glass will have Flat Edge Polish low-iron low-iron satin satin Flat Edge Polish 5 v. 9.18 Technical specifications subject to change
Installation Instructions STEP 1: ATTACH. Screw Wall Standard to wall stud or use anchor to attach to the wall. 1- FRONT VIEW 1-3-QTR VIEW STEP 2: TRAP PLATE MUST ROTATE. Using the Allen wrench, loosen the Trap Plate enough that it may rotate easily (Figure 2a, 2b). Turn trap plate to align with Arm Bracket ridge, as shown (Figure 2c). Align Trap Plate with side channel. Be sure Trap Plate is loose and fully inserted into Wall Standard side channel (Figure 2d). Once tightened, the Trap Plate will rotate inside the side channel of the Wall Standard, locking the Arm Bracket into place (Figure 2e). FIGURE 2a FIGURE 2b FIGURE 2c FIGURE 2d FIGURE 2e STEP 3: INSTALL FASCIA (Optional) Attach Fascia to Front Channel of Wall Standard by tapping Fascia into the Standard Front Channel with a soft cloth and hammer (Figure 3c) ensuring a snug fit to Wall Standard. FIGURE 3a FIGURE 3b FIGURE 3c ALUMINUM FASCIA ALSO AVAILABLE 6 v. 9.18
Cleaning and Care To insure proper cleaning and care of your product, please follow these simple suggestions for our materials: Glass ( or satin surfaces) We recommend using 99% isopropyl alcohol, citrus or vinegar based cleaners on a clean, non-abrasive cloth or paper towel. If a heavy stain is present and does not come clean using the suggestions above, use isopropyl alcohol with a Magic Eraser by gently scrubbing until the mark is removed. Backpainted Glass Follow instructions above for the and/or satin surface of the glass, opposite the painted side. For the backpainted water based coating, we recommend using a mildly damp (water only) on a non-abrasive cloth to gently clean the coated side of the glass. Aluminum Extrusions Use a clean cloth with a mild detergent to clean the aluminum. NEVER use an abrasive cleaning pads such as a metallic sponge, solvents, strong detergents or other chemical agents when cleaning glass or aluminum. 7 v. 9.18
Warranty Element Designs aluminum frame cabinet door products are covered by a limited liability warranty from defects in material and workmanship over the functional lifetime of the doors. The warranty includes any defects in the fabricated door size, boring locations, aluminum framing flaws outside of quality standards, and glass imperfections outside of quality standards. Element Designs also warrants its doors from deterioration, discoloring, degrading, or overall changing through the course of the product s lifetime. This warranty does not apply if, in the judgment of Element Designs, the product fails due to damage from shipment, handling, storage, accident, abuse or misuse, or if it has been used or maintained in a manner not conforming to product s care instructions, has been modified in any way, or has been defaced. Repair by anyone other than Element Designs or an approved agent voids this warranty. The maximum liability of Element Designs is the product purchase price. 8 v. 9.18