1.9 Information and installation instructions for self adhesive mounting bases HellermannTyton use two different types of adhesive for self adhesive bases: acrylate and synthetic rubber. These differ in the operating temperature range and the 'pull off' force of the adhesive. Synthetic rubber has an excellent initial grip, allowing for almost immediate use. Acrylate adhesive has less initial grip, so there is a need to wait for a few hours before use, but has a higher 'pull off' force than synthetic rubber. This enables a permanent fixing lasting months or even years. To use these adhesives the surface must be dry, and free of dust, oil, oxides, parting agents and other impurities. For this the use of isopropane/ water (50/50) is recommended. After cleaning allow the surface to dry completely. Peel off the protective backing on the self adhesive base, ensuring the adhesive is not touched. Apply the part to the surface and press down firmly for several seconds. Acrylate Synthetic rubber Base material PE foam or PU foam Base material PE foam range at least up to +105 ºC range at least -40ºC to +60ºC 1. Instructions for use The surface must be dry, free from dust, oil, oxides, parting agents and other impurities. The surface to be glued should be cleaned using a clean cloth and isopropanol /water (50/50). When using other appropriate cleaning agents, ensure that they do not attack the surface or leave any residues. 2. 4. After cleaning allow the surface to dry completely. Press down firmly on the base for several seconds. 3. 5. Peel off protective backing and ensure the adhesive area is not touched. Depending on the type of adhesive, wait for several minutes (synthetic rubber) or hours (acrylate) so that the adhesive can bond completely with the surface.!we will be happy to send you on request an up to date technical datasheet for whichever adhesive you are using. 162
1.9 Fixing Parts with Special Adhesive SolidTack-Series Sometimes it is not possible to fix a cable with standard fixing parts and mounting bases. This is a common problem with varnished surfaces when it is not possible to drill a hole, use an edge clip or weld stud, or where methods are too time consuming and expensive. It is also problematic for surfaces such as PE or PP where a standard adhesive base does not work. For these applications a new mounting base range with special adhesive has been developed. The adhesive tape is made of an acrylate mass with a superior initial tack, achieving a strong bond on painted surfaces and plastics with a low surface energy such as PE or PP. Three different sizes of mounting base for cable ties are available. Two separate clamp sizes are also available to fix and secure flat and round cables without using a cable tie. These products work on varnished and powder coated surfaces as used in the railway, aviation or automotive industry. They can also be used on plastic covers, cases and parts as used in a variety of other industries. Acrylate Adhesive Adhesive mod. Acrylate -40 C to +90 C SolidTack products work on varnished and powder coated surfaces. Polyamide 6.6 (PA66) -40 C to +85 C Continuous, Polyamide 6.6 High Impact Modified (PA66HIR) -40 C to +80 C Continuous, UL94 HB (excluding MB3, MB4, MB5 Flat Ribbon Cables FKH Series Ø (FH) Strap max. (G) Colour MB Series 151-00432 MB3APT 19.0 19.0 3.8 3.1 4.1 PA66 Black (BK) 151-00514 MB3APT 19.0 19.0 3.8 3.1 4.1 PA66 Natural (NA) 151-00433 MB4APT 28.0 28.0 4.7 4.0 5.4 PA66 Black (BK) 151-00587 MB4APT 28.0 28.0 4.7 4.0 5.4 PA66 Natural (NA) 151-00434 MB5APT 38.0 38.0 6.4 4.7 10.0 PA66 Black (BK) FKH Series For Cable max. 151-00312 FKH50AVHB 56.5 25.0 3.1 50.0 PA66HIR Black (BK) 151-00313 FKH80AVHB 86.0 25.0 3.1 80.0 PA66HIR Black (BK) 163
1.9 Self Adhesive / Screw Fixing MB-Series Square-Cut Available in either screw or self adhesive mounting this range offers a safe and secure fixing base. Simple to install with a screw or bolt they give excellent security, particularly in areas of high vibration. The Self Adhesive mounts are designed to offer the maximum surface area, and in conjunction with the specially developed adhesive ensures that a very high pull-off force is achieved.the MB mounts offer '4-way' entry for the cable tie enabling quicker and more flexible installation. MB and TY. MB3A. Designed specifically for holding heavier cable bundles these mounting bases can be used in many industries from agriculture to truck manufacture. They offer a very secure fixing and can be used with a wide variety of heavy duty cable ties up to 8mm wide. Polyamide 6.6 (PA66) -40 C to +85 C Continuous, For more information on the types of adhesive used please turn to page 162. MB2A MB3-5(A) MB4CA Ø (FH) Centres (F) Strap max. (G) Colour Adhesive 151-01802 MB2A 13.0 13.0 4.1 2.7 PA66 White (WH) Synthetic rubber 151-28359 MB3 19.0 19.0 3.8 3.1 13.2 4.1 PA66 Natural (NA) 151-28349 MB3A 19.0 19.0 3.8 3.1 13.2 4.1 PA66 Natural (NA) Synthetic rubber 151-28320 MB3A 19.0 19.0 3.8 3.1 13.2 4.1 PA66 Black (BK) Synthetic rubber 151-28479 MB4 28.0 28.0 4.7 4.0 20.0 5.4 PA66 Natural (NA) 151-28469 MB4A 28.0 28.0 4.7 4.0 20.2 5.4 PA66 Natural (NA) Synthetic rubber 151-28430 MB4A3 28.0 28.0 4.7 4.0 20.2 5.4 PA66 Black (BK) Acrylate 151-28459 MB4CA 29.0 29.0 5.7 4.2 5.4 PA66 Natural (NA) Synthetic rubber 151-28449 MB4CAS* 29.0 29.0 5.7 4.2 5.4 PA66 Natural (NA) Synthetic rubber 151-00324 MB5 37.7 37.7 6.2 4.7 25.3 10.0 PA66 White (WH) 151-28529 MB5A 37.7 37.7 6.9 4.7 25.3 10.0 PA66 Natural (NA) Synthetic rubber 151-28530 MB5A3 38.0 38.0 6.4 4.7 25.3 10.0 PA66 Black (BK) Acrylate * Plastic box Please note! Not all products listed on this page may have this approval. For product specific approvals please refer to the Appendix. 164
1.9 Self Adhesive / Screw Fixing TY-Series longish design TY mounts are particularly suitable for applications with minimal space - they are mounted into the equipment prior to cable installation. The cables can be attached using a range of standard cable ties. These products are designed for simple, yet robust, installation in a wide variety of applications - particularly used in telecoms equipment, switchgear and control cabinets. TY3G1 (S) TY8G1 (S) Polyamide 6.6 UV Resistant (PA66W) -40 C to +85 C Continuous, Polyamide 6.6 (PA66) For more information on the types of adhesive used please turn to page 162. -40 C to +85 C Continuous, Ø (FH) Centres (F) Strap max. (G) Colour Adhesive 151-21319 TY3G1 20.0 14.0 3.7 2.2 15.0 4.0 PA66 Natural (NA) 151-11319 TY3G1S 20.0 14.0 3.7 2.2 15.0 4.0 PA66 Natural (NA) Acrylate 151-11310 TY3G1S 20.0 14.0 3.7 2.2 15.0 4.0 PA66W Black (BK) Acrylate 151-21819 TY8G1 32.0 25.0 5.2 3.2 15.0 8.0 PA66 Natural (NA) 151-11819 TY8G1S 32.0 25.0 5.2 3.2 15.0 8.0 PA66 Natural (NA) Acrylate 151-11810 TY8G1S 32.0 25.0 5.2 3.2 15.0 8.0 PA66W Black (BK) Acrylate 165
1.9 Self Adhesive / Screw Fixing Q-mount Series QM Q-mounts allow a 4-way entry for Q-ties and are available in a screwable or self adhesive version. Due of the special design of the mounting base, they offer a perfect solution in combination with the Q-tie cable ties. The Q-mount keeps the Q-tie in place during pre-assembly and ensures that the Q-tie does not slip out even in difficult situations, for example vertical mounting positions. Q-mount QM, 4-way entry, adhesive/screwable. Please find more Q-Series products for your system solution on page 81 and 508. Mounting Base Q-mount The Q-mount base locks the Q-tie in vertical positon, your hands are free to apply the cables. Synthetic rubber Base material range PE foam at least -40ºC to +60ºC Colour Polyamide 6.6 (PA66) Natural (NA), Black (BK) -40 C to +105 C Continuous, Ø (FH) Strap max. (G) Colour Adhesive 151-10901 QM20 20.0 20.0 3.7 3.1 4.0 PA66 Natural (NA) 151-10902 QM30 30.0 30.0 4.5 4.1 5.1 PA66 Natural (NA) 151-10903 QM40 40.0 40.0 5.5 4.1 8.4 PA66 Natural (NA) 151-10904 QM20A 20.0 20.0 3.7 3.1 4.0 PA66 Natural (NA) Synthetic rubber 151-10905 QM30A 30.0 30.0 4.5 4.1 5.1 PA66 Natural (NA) Synthetic rubber 151-10906 QM40A 40.0 40.0 5.5 4.1 8.4 PA66 Natural (NA) Synthetic rubber 151-10911 QM20 20.0 20.0 3.7 3.1 4.0 PA66 Black (BK) 151-10912 QM30 30.0 30.0 4.5 4.1 5.1 PA66 Black (BK) 151-10913 QM40 40.0 40.0 5.5 4.1 8.4 PA66 Black (BK) 151-10914 QM20A 20.0 20.0 3.7 3.1 4.0 PA66 Black (BK) Synthetic rubber 151-10915 QM30A 30.0 30.0 4.5 4.1 5.1 PA66 Black (BK) Synthetic rubber 151-10916 QM40A 40.0 40.0 5.5 4.1 8.4 PA66 Black (BK) Synthetic rubber 166
1.9 Paste Adhesive Mount PMB5 The PMB5 paste adhesive mount is suitable for fixings with paste/liquid adhesive. With several holes in the plate a firm closure between the mount and the cured adhesive is achieved. The PMB5 is made of heat resistant material so that it can also be applied in combination with hot-melt adhesive. The mount can be used with a variety of cable ties up to 4.8 mm width. To complement the MB Self Adhesive Cable Tie Mounts the PMB5 paste adhesive mount was developed. In combination with different paste/liquid adhesives this mount can even be installed onto uneven surfaces. In the same way the PMB5 is a good alternative if a fixing without screws is necessary. This paste adhesive mount is used in the railway supply industry as well as in the renewable energy industry. Further applications are in the ship building industry, in the electrical industry and the production of switching cabinets. PMB5 mount with paste adhesive. L G H PMB5 W Polyamide 6.6 Heat Stabilised (PA66HS) -40 C to +105 C continuous, (+145 C for 500 h) UL94 V2 Strap max. (G) Colour 151-00498 PMB5 36.0 36.0 10.7 4.8 PA66HS Black (BK) 167