AVENTOS HK-S Assembly instructions Required parts Lift mechanism set Set includes: Lift mechanism (qty 2) Cover plate (left and right) Also includes: SCHR 4X #7 x mm (-/8 ) wood screw (qty 0) Power factor Opening angle 9 9 07 20K2B00.N 40 8 07 20K2C00.N 86 77 07 20K2E00.N Wood or wide aluminum door mounting plate Wood or wide aluminum mounting plate (qty 2) Wood or wide aluminum mounting plate Installation screw for wood doors Installation screw for wide alum doors 7H00 606N or 606P 7072A Narrow aluminum door mounting plate Narrow aluminum mounting plate (qty 2) (for use with AVENTOS HK-S only) Includes 699.00 installation screws (qty 4) Narrow aluminum mounting plate 20K4A00A02 Recommended parts for tension adjustment Use of a POZI bit insert and bit holder is recommended when adjusting the tension of the lift mechanism. #2 x 2" POZI bit insert POZI BIT #2x2 /4" bit holder BIT HOLDER Subject to technical modifications without notice. 20
Assembly WARNING Risk of injury from spring-loaded arm Do not push arm assembly down or leave in the down position Remove mechanism before installing or removing cabinet Locating pin locations and minimum depth Panel Face frame 2 2 64 Z 64 Z min. NOTE: Face frame cabinets must be blocked out flush with the frame. Overlay up to 20 24 26 Z 7. 4. Universal individual template is available for pre-boring locating pins 6.0.02 2 Attaching the lift mechanism Align the lift mechanism in the cabinet using the mm locator pins and attach the mechanism with the three wood screws provided. min. Ø #7 x mm (-/8") wood screws (qty ) 2 Subject to technical modifications without notice. 20
Attaching the mounting plates a Wood/wide aluminum frame doors b Narrow aluminum frame doors 2 8 + Overlay Overlay 6 + Overlay Overlay 2. + Overlay NOTE: Attach each mounting plate with two 606N or 606P wood screws for wood doors, two 7072A screws for wide aluminum doors or two 699.0 screws for narrow aluminum doors 4 Raise lever arm assembly with caution A B Standing at arm s length carefully raise the arm to the upright position. For the 20K2B00.NA, carefully remove the plastic tab. NOTE: Do not remove plastic tab until just before attaching the door Risk of injury from spring-loaded arm. Subject to technical modifications without notice. 20
Assembly Attaching the door Attach the door using the CLIP mechanism in the mounting plate. 6 Adjust the door tension Use a screw gun, POZI driver bit insert and bit holder to adjust each lift mechanism to the desired tension. 4 Subject to technical modifications without notice. 20
7 Finalize the door adjustments ± 2 mm ± 2 mm ± 2 mm Use a POZI screwdriver on cam adjustments for each of the three -dimensional adjustments. 8 Attach cover caps Place the left and right cover plates over the appropriate lift mechanisms and snap them in place. Subject to technical modifications without notice. 20
Removal WARNING Risk of injury from spring-loaded arm Do not push arm assembly down or leave in the down position Remove mechanism before installing or removing cabinet Removing the door Disengage the CLIP mechanism of the lever arm from the mounting plate Support the door with one hand and repeat on the other side 2 Removing the covers Remove the cover plate. 6 Subject to technical modifications without notice. 20
Other information Panel and Face frame clearance X door thickness door height Inch mm /2.0 /6.06. /2.094 2 /8.2 /2.6 4 07 /6.88 7 /2.29. /4.2 6 9 /2.28 7 Door thickness 6 9 22 26 X 70 9 49 /6. 8 /2.44 9 /8.7 9. /2.406 0 7 /6.48 /2.469 2 /2. 7 /2.. 9 /6.6 4 9 /2.94 /8.62 6 2 /2.66 7 /6.688 7. 2 /2.79 8 /4.7 9 2 /2.78 20 /6.8 20. 27 /2.844 2 Blum, Inc. 800-48-6788 sales.us@blum.com blum.com Subject to technical modifications without notice. 20 INST-AVT2-04. 7 /8.87 22 29 /2.906 2 /6.98 24 /2.969 24. 2.4