Assembly Instructions for Model: MF110 Thank you for choosing a Sanus Systems VisionMount wall mount. The MF110 is designed to mount LCD flat panels with VESA (Video Electronics Standards Association) hole pattern up to 200mm x 200mm and weighing up to 100 lb [45.5 Kg] to a vertical wall. It will allow the television to be pulled out 9.5 [241.3 mm] from of the wall. It will allow you to swivel the television ±30 (may vary with size of television), tilt +5 to -15, and have a ±6 roll control. CAUTIO: The size and weight of your television must not exceed 100 Lbs [45.5 Kg]. The wall must be capable of supporting five times the weight of the television plus the wall mount. ever use defective parts. Improper installation may cause property damage or personal injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or www.sanus.com. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Check carefully to make sure that there are no missing or defective parts. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. OTE: This mount is not intended for use on brick, concrete block, concrete, or steel wall studs. Typical wall anchors do not have sufficient holding power to support this mount. It is up to the installer to verify the safety of any installation method or hardware that is not provided by or recommended by Sanus Systems. Sanus Systems makes every effort to assure all necessary television mounting hardware is included. If the television mounting hardware you need is not included please consult your local hardware store or call Sanus Systems. Required Tools: Drill, 3/16 drill bit, wrench set, Philips screwdriver Supplied Parts and Hardware: (Some parts are not shown at the same scale) Wall Plate - A Qty.1 Arm Assembly - B Qty.1 M4 x 12 mm Bolt - C M5 x 12 mm Bolt - D M6 x 12 mm Bolt - E M4 x 30 mm Bolt - F M5 x 30 mm Bolt - G M6 x 35 mm Bolt - H M4 Lock Washer - I M5 Lock Washer - J M6 Lock Washer - K Sanus Systems 2221 Hwy 36 West, Saint Paul, M 55113 10.11.06 (6901-100044) Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
M4/M5 Spacer - L M6 Spacer - M M4/M5 Washer - M6 Washer - O Lag Bolt - P Lag Bolt Wsher - Q Wire Tie Clip - R Safety Bolt - S Qty. 2 Wire Tie - T 7/32 Allen Key - U Qty. 1 3/16 Allen Key - V Qty. 1 Step 1: Mount the Wall Plate: Wood Stud installation only CAUTIO: Do not overtighten the Lag Bolts (P). Tighten Lag Bolts until the Lag bolt Washer (Q) is pulled firmly against the Wall plate (A). If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch [15.8 mm] in thickness. Failure to heed this caution may result in property damage and/or personal injury. Diagram 1 Wood Stud Mounting: The Wall Plate (A) must be mounted to a wood stud. Use a high quality stud sensor to locate a stud. It is a good idea to verify where the stud is located with an awl or thin nail. Pre-drill a 2.5 [63.5 mm] deep hole at the desired height in the stud using a 3/16 drill bit. Make sure the hole is in the center area of the stud. Use this location for the middle hole in the Wall Plate. Use the Wall Plate as a template to mark the location of the top and bottom holes. Make sure the Wall Plate is level and drill a 2.5 [63.5 mm] deep hole using the 3/16 drill bit in the marked locations. Attach the Wall Plate to the wall using three Lag Bolts (P) and three Lag Bolt Washers (Q). Make sure the Wall Plate is oriented so the flat surface in the center of the plate is against the wall. See Diagram 1. OTE: The TV will be vertically centered on the Wall Plate once it is mounted. P Q A Stud Drywall cutaway to show studs.
Step 2: Add Arm Assembly to a television with a flat back OTE: If your television has a curved back, or any other obstruction, proceed directly to Step 3. First, determine the diameter of the Bolt (C,D,E) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below. You will thread the Bolt through the appropriate Lock Washer (I,J,K), a Washer (, O), the Monitor Plate, and finally thread it into the TV. Proceed to tighten all four Bolts until tight with a phillips screw driver. OTE: Arm has been cutaway in this Step to show critical parts. M5 Diameter Bolt J M6 Diameter Bolt D O K E M4 Diameter Bolt I C
Step 3: Add Arm Assembly to a television with a curved back, recessed area around the threaded inserts or any other obstruction. First, determine the diameter of the Bolt (F,G,H) your TV requires by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below. You will thread the Bolt through the appropriate Lock Washer (I,J,K), a Washer (, O), the Monitor Plate, the appropriate Spacer (L,M) and finally thread it into the TV. M5 Diameter Bolt L J M6 Diameter Bolt G M O K H M4 Diameter Bolt L F I
Step 4: Hang Arm Assembly on Wall Plate CAUTIO: This step may require two people to lift the assembly onto the Wall Plate. Sanus Systems is not responsible for property damage and/or personal injury. Orient the Arm Assembly (B) so that the arm extends directly away from the television and the transfer bracket is parallel with the television. Lift up the assembly and hook the transfer bracket onto the tab on the top of the Wall Plate (A) as shown in Diagram 4. Diagram 4 Wall Transfer B A Step 5: Add Safety Bolts CAUTIO: make sure the Safety Bolt (S) is tight. A loose Safety bolt will result in an unstable installation which may result in property damage and/or personal injury. Thread a Safety bolt (S) into the threaded hole on each side of the Transfer and tighten them with a phillips screwdriver until they are tight. See the detailed View of Diagram 5 for assistance. Diagram 5 Detailed View Transfer S OTE: Lower Hole on transfer bracket may be used to add a padlock for added security.
Step 6: Leveling and Adjusting Tension on the Monitor CAUTIO: Do not remove the Tension uts labeled in Diagram 6a. Removing Tension uts may result in property damage. Once the television is mounted onto the Wall Plate (A), and the Safety Bolts (S) are tight, it can be adjusted to level. Slightly loosen the two Allen Bolts on the back of the Arm Assembly (B). Once those two bolts are loosened, the television can be adjusted ±6º until level. When the television is level retighten the two Allen Bolts. The tilt can be adjusted by simply tilting the television. If you need to adjust the tension of the tilt, you can do so with the Tension Knobs. The Tension uts labeled in Diagram 6a can be slightly loosened or tightened to adjust the tension of the Arm Assembly. If you need to adjust the Tension ut closest to the TV, you must remove the Safety, adjust the tension and re-install the Safety as shown in the Safety installation view of Diagram 6b. Safety Diagram 6a Tension ut B Diagram 6b Safety Allen Bolts Tension Knobs Tension ut Step 7: Cable/Wire Management CAUTIO: Do not run cables through a pinch point. Running cables through pinch points may result in damage to the cables and/or personal injury. Before beginning cable management pull the television into the position as far from the wall as possible. Leave some slack in the cables so that during motion so there is no added tension on the connectors. Wire Tie Clips (R) can be attached to the holes in the top and the bottom of the Arm Assembly (B) by simply pressing them into place as shown in the Detailed View of Diagram 7. Wire Ties (T) can then be added to the Wire Tie Clips. Diagram 7 Detailed View R B CSAV, Inc. and its affiliated corporations and subsidiaries (collectively, CSAV ), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions, or variations. or does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.