INSTALLATION INSTRUCTIONS Square Free Standing Floor Mount Tub Filler Model D35900900 Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin. RECOMMENDED TOOLS AND MATERIALS Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun. Tubing Cutter Caulking Channel Locks 6mm Hex Wrench ROUGHING-IN DIMENSIONS: For reference 7-5/8" (95 mm) *Adequate floor support is required. The wood support must be a minimum of 2" (5 mm) thick by 0" (25 mm) wide. 2x6 lumber is NOT adequate for this application. IMPORTANT NOTICE TO THE INSTALLER! Please check with your local Code Authority for acceptable installation requirements for this Roman Tub set with hand shower. Some local codes may require a vacuum breaker and/or a pressure balanced mixing valve to be installed in conjunction with this product. 26-7/8" (68 mm) 5/6" (7 mm) PLASTER GUARD FINISHED FLOOR 2-5/8" (67 mm) MIN. -3/" (2 mm) MAX. /2" NPT FEMALE THREAD HOT Sealing Tape 7-7/8" (99 mm) max Finished Surface min 0" (25 mm) MIN. Adjustable Wrench -/8" (0 mm) -5/8" (0 mm) -3/" SQ. (20 mm) ESCUTCHEON FINISHED FLOOR Center Level Level 32-5/8" - 3-5/8" (830-880mm) *WOOD SUPPORT FLOOR JOIST /2" NPT FEMALE THREAD COLD 3-7/8" - 33-7/8" (809-859 mm) *2" MIN. (5 mm) Drill FINISHED WALL 0-5/8" (27 mm) 7-3/8" (87 mm) 2-/2" MIN. (6 mm) 2" (50 mm) Flat Blade Screwdriver Phillips Screwdriver S A V E F O R F U T U R E U S E In the United States: DXV One Centennial Avenue Piscataway, New Jersey 08855 Attention: Director of Customer Care For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 227-273 www.dxv.com In Canada: DXV 5900 Avebury Road Mississauga, Ontario L5R 3M3 Canada Toll Free: -800-387-0369 Local: 905-306-093 Fax: -800-395-98 www.dxv.ca In Mexico: DXV Via Morelos 330 Col. Santa Clara Coatitla Ecatepec, Estado de México 5550 Toll Free: 0-800-839200 www.dxv.mx Product names listed herein are trademarks of AS America, Inc. AS America, Inc. 207 - -
INSTALL TUB FILLER FLOOR SUPPORT CAUTION Turn off hot and cold water supplies before beginning. Note: Refer to Roughing-in Dimensions on first page for additional information. Adequate floor support is required. The WOOD SUPPORT () must be a minimum of 2" (5 mm) thick by 0" (25 mm) wide. 2x6 lumber is NOT adequate for this application. WOOD SUPPORT () must be located with in the MIN. and MAX. arrows that are marked on the PLASTER GUARD (3). IMPORTANT: Use a ROUND BUBBLE LEVEL (2) to level the WOOD SUPPORT (). The WOOD SUPPORT () must be perfectly level. Secure WOOD SUPPORT () to floor joists. Check for level again. FINISHED FLOOR LINE 0"-2" (25-305mm) WOOD SUPPORT 2 ROUND BUBBLE LEVEL 2-5/8" (67mm) MIN. -3/" (2mm) MAX. 2" (5mm) MIN. 0" (25mm) MIN. FLOOR JOIST 2 INSTALL HOT AND COLD WATER SUPPLIES Sweat together Hot and Cold Supply assemblies. Apply sealing tape to threaded connections. Tighten connections so that the Hot inlet will be on the left when facing the front of the Tub Filler. Note: Turn MANIFOLD MOUNTING BASE () over. The Hot and Cold inlets are marked. See View A. SEALING TAPE HOT VIEW A VIEW A COLD - 2 -
3 INSTALL MANIFOLD MOUNTING BASE Locate the position on the wood support where the MANIFOLD MOUNTING BASE () will be installed. Use the MANIFOLD MOUNTING BASE () as a guide to mark the four mounting hole locations. Drill pilot holes if required. Secure the MANIFOLD MOUNTING BASE () to the WOOD SUPPORT () with SCREWS (5) provided. Verify that the MANIFOLD MOUNTING BASE () is level and then fully tighten SCREWS (5). 3 HOT 2 COLD FINISH PLUMBING CONNECTIONS Finish all Hot and Cold supply connections to the MANIFOLD MOUNTING BASE (). Loosen the two PLASTER GUARD SCREWS (6) and remove the PLASTER GUARD (7). Make sure the two TEST PLUGS (8) are tight, but do not over tighten. Turn on water supplies and test for leaks. Turn off water supplies. Replace PLASTER GUARD (7) and attach with SCREWS (6). 2 3 HOT COLD - 3 -
5 FINISH FLOOR INSTALLATION Complete the installation of the Finished Floor. Tile as close to the PLASTER GUARD (7) as you can. Caulk between Finished Floor and PLASTER GUARD (7). FINISHED FLOOR ROUGH FLOOR 6 REMOVE EXPOSED PLASTER GUARD Cut the exposed part of the PLASTER GUARD (7) flush with the finished floor. Be careful not not damage the floor. FINISHED FLOOR 2 mm to mm - -
7 REMOVE HOT AND COLD TEST PLUGS With a wrench remove the center TEST PLUG (8) first. Figure A. If the TEST PLUGS (8) cannot be removed in one piece as shown in Figure A, the lower half will have to be removed using a 6 mm Hex Wrench, Figure B. 6mm HEX WRENCH FIGURE A FIGURE B 8 CLEAN ALL FITTING MOUNTING SURFACES Vacuum and clean all mounting surfaces and mounting holes. IMPORTANT: Debris on sealing surface will cause Tub Filler to leak at this connection. CLEAN - 5 -
9 INSTALL TUB FILLER Note: Floor and plaster guard are removed for clarity in this illustration. Remove PLASTIC CAP from MOUNTING ADAPTER (0). Before final installation, check that all sealing surfaces are clean and that the two O-RINGS (9) are installed in the MOUNTING ADAPTER (0). Install the MOUNTING ADAPTER (0) into the MANIFOLD MOUNTING BASE (). Install the four MOUNTING SCREWS and WASHERS () through the MOUNTING PLATE (2) and into the MANIFOLD MOUNTING BASE (). Do not tighten. Rotate the TUB FILLER right or left to align with Tub. Tighten MOUNTING SCREWS () with 6mm Hex Wrench to secure TUB FILLER. 9 6 3 ALIGN 8 Install HAND SHOWER BRACKET (3) onto ADAPTER (). Tighten set screw with HEX WRENCH (5) supplied to secure BRACKET (3). Install SEALS (6) on both ends of the SPRAY HOSE (7). Connect the end with the flat to the DIVERTER (8) using an adjustable wrench. Hand tighten the connection to the HAND SHOWER (9). Note: When not in use, the HAND SHOWER (9) should be seated in the HAND SHOWER BRACKET (3). 5 7 6 FLAT 6mm HEX WRENCH O-RING SEALS 9 2 REMOVE PLASTIC CAP 0-6 -
0 TEST INSTALLED FAUCET Move HANDLE (20) into off position and remove AERATOR (2). Turn on water supplies and check all connections for leaks. Check MANIFOLD () connections for leaks. Apply sealant to under side edge on ESCUTCHEON (22). Slide ESCUTCHEON (22) down to finished floor. Press into place. Clean up excess sealant. Operate HANDLE (20) On to Off, Hot and Cold to flush water lines thoroughly. Lift HAND SHOWER (9) from the holder and direct spray into tub. Pull DIVERTER KNOB (23) and check HAND SHOWER (9) and HOSE (7) connections for leaks. Push DIVERTER KNOB (23) in and place HAND SHOWER (9) into HOLDER (3). Replace AERATOR (2). 2 9 3 23 20 7 22 APPLY SEALANT - 7 -
Square Free Standing Floor Mount Tub Filler MODEL NUMBER D35900900 M96568-YYY0A AERATOR ASSEMBLY M96569-YYY0A DIVERTER ASSEMBLY Replace the YYY with appropriate finish code POLISHED CHROME 00 BRUSHED NICKEL MATTE BLACK 23 M96567-YYY0A HAND SHOWER BRACKET KIT M96566-YYY0A HAND SHOWER M97063-0070A ADAPTER M96572-0070A CARTRIDGE M9657-YYY0A HANDLE ESCUTCHEON M96570-YYY0A HANDLE KIT H9600.XXX HOSE & SEALS M96563-0070A FAUCET MOUNTING KIT M96560-0070A SCREW & ANCHOR KIT - 8 -