www.heuletool.com For more case studies, testimonials, and videos We provide online tool selectors for the COF,, DEF and BSF product groups. Simply enter your application information and the correct tool will be provided complete with order number and sample drawing. We are also available on: ll Purpose Front & Back Chamfering of Through Holes Chamfers front and back surfaces in a single pass Provides high quality, consistent chamfers Coated carbide blades provide long tool life Sizes - (.97 -.984 ) available from stock 86.860.9900 www.heuletool.com Cat. No. HTC0 HTC08
Introduction Introduction The HEULE chamfering tool is the answer for today s manufacturers requiring simpler and more flexible solutions without sacrificing quality or tool life. is a very simple tool for deburring and/or chamfering through holes on the top and bottom without reversing the spindle, dwelling, or indexing the part. The tool offers a simple to use high quality chamfering tool with Carbide inserts coated with TiN, TiCN, or TilN to meet today s manufacturing needs. High Quality Consistent Chamfers The blades are ground with a patented geometry developed by HEULE to produce quality chamfers and eliminate secondary burrs. Different chamfer sizes can be achieved by selecting a different blade. There is no need for adjustments or operator intervention. In hard materials above Rc=8, request the -DF geometry. Long Tool Life The solid body design of the tool provides the highest durability of any deburring tool. dditionally, the coated carbide blades give longer tool life and faster operation speeds. This durability and blade life make the ideal choice for high volume manufacturers. Wide Range of Standard Tools tools are available from stock from to (0.079-0.984 ). The Cassette makes it possible to deburr even larger holes quickly and efficiently and is also available from stock. How Does It Work? s the rotating tool is fed into the hole, the front cutting edge deburrs the top of the hole by cutting a 4 chamfer. s the tool feeds into the part, the blade is forced into the body and slides in the blade window. When the blade is in the hole, only the ground sliding surface touches the hole protecting it from damage while the tool is fed through the part. There is no need to stop or reverse the spindle. When the blade reaches the back of the part the coiled spring acts with the control bolt to push it back out into cutting position. The back edge is deburred and chamfered as the tool is withdrawn. When the blade is again in the hole, the tool can be rapid fed out and on the next hole. Typical Parts How to Select the Tool and Blade: Selecting the proper tool is very easy and you only need to know the bore diameter and desired chamfer size. Tools are sold without blades. In most cases, there are four choices of blade sizes based on size of desired edge break. (Example:.00,.00,.00,.040 x 4 ) Sample Tool Selection. Use the bore size to select a tool body. Ød - Select the largest tool that fits the bore.. Use the desired chamfer size to select a blade. ØD - Select the proper cutting blade. Order Example: Bore Ø.00 / Chamfer Ø.0 (.0 x 4 ) Tool Body Order Number: -49 Blade Order Number: GH-Q-M-0744 88.860.9900 www.heuletool.com -860-9900 www.heuletool.com 89
Chamfering Tools For holes.0-9..97 -.74 Spare Parts Minimum Hole Ø Tool Diameter Tool Holder.0.97 4.9.9 -.0..7.4.4 -. 6.0.6.9. -6.0 6..6 6.4. -6. 7.0.76 6.9.7-7.0 7..96 7.4.9-7.. 7.8.07-8.. 8.. -8..4 8.8.46-9..74 9..66-9. * Blade sold separately Shank Diameter ØS Ø8 Ø8 Ø8 Ø8 Ø8 Ø8 Ø0 Ø0 Ø0 Ø0 (ØD= ØD+0.6) Blade Options* Front and Back Cutting Gs, 90, Carbide, TiIN GH-Q-M- Chamfer ØD () -004 (.) -00 (6.0) -006 (6.) -007 (7.0) -008 (7.) -009 () -00 (8.) -0 () -0 (9.) -0-00 (6.0) -006 (6.) -007 (7.0) -008 (7.) -009 () -00 (8.) -0 () -0 (9.) -0-04 (0.) -006 (6.) -007 (7.0) -008 (7.) -009 () -00 (8.) -0 () -0 (9.) -0-04 (0.) -0 (.0) BLDE OPTIONS -007 (7.0) -008 (7.) -009 () -00 (8.) -0 () -0 (9.) -0-04 (0.) -0 (.0) -06 (.) 7 Spare Parts 4 6 Set Screw Spring Distance Pin Control Bolt Blade Wrench GH-H-S-07 GH-H-F-009 GH-Q-E-004* GH-Q-E-0008 See Below GH-H-S-0 * For - through -9. use GH-Q-E-0068 Blades GH-S geometry 90 angle (a = 90 ) Max. Chamfer ØD. 6.0 6. 7.0 7. 8. 9. 0.0 0..0..0..0 fab TiIN coated GH-Q-M-004 GH-Q-M-00 GH-Q-M-006 GH-Q-M-007 GH-Q-M-008 GH-Q-M-009 GH-Q-M-00 GH-Q-M-0 GH-Q-M-0 GH-Q-M-0 GH-Q-M-04 GH-Q-M-0 GH-Q-M-06 GH-Q-M-07 GH-Q-M-08 GH-Q-M-09 * Non-stock standard item with extended delivery time bco TiIN coated* GH-Q-M-04 GH-Q-M-0 GH-Q-M-06 GH-Q-M-07 GH-Q-M-08 GH-Q-M-09 GH-Q-M-0 GH-Q-M- GH-Q-M- GH-Q-M- GH-Q-M-4 GH-Q-M- GH-Q-M-6 GH-Q-M-7 GH-Q-M-8 GH-Q-M-9 4 C 4.40 4.6 4.70 4.8.0.70.80 6.0 6.80 7.0 7.80 7.80 8.0 8. 8.80 0.8..6.6.6.7.7.7.7.7.7.8.8.8.8.8 6 PROGRMMING SPRE PRTS 7 CHNGE BLDES 90.860.9900 www.heuletool.com -860-9900 www.heuletool.com 9
8 Chamfering Tools For holes -.0. -.47 8 Spare Parts 8 Minimum Hole Ø. 8...4 9..74 0.0.94 0..4.0.4..4 Tool Diameter 7.8.07 8..7 8.8.46 9..66 9.8.86 0..406 0.8.4..44.0.47.8.46 * Blade sold separately Tool Holder 8-8- 8-4 8-74 8-94 8-4 8-4 8-4 8-47 (ØD= ØD+0.8) Blade Options* Front and Back Cutting Gs,90, Carbide, TiN GH-Q-M- Chamfer ØD () -070 (8.) -07 () -07 (9.) -07 () -07 (9.) -07-074 (0.) -07 (.0) -076 (.) -077 (.0) -078 (.) -07 (9.) -07-074 (0.) -07 (.0) -076 (.) -077 (.0) -078 (.) -079 (.0) BLDE OPTIONS -07-074 (0.) -07 (.0) -076 (.) -077 (.0) -078 (.) -079 (.0) -070 (.) 8 Spare Parts 8 4 6 Set Screw Spring Distance Pin Control Bolt Blade Wrench GH-H-S-09 GH-H-F-0007 GH-Q-E-008 GH-Q-E-000 See Below GH-H-S-00 Blades 8 GH-S geometry 90 angle (a = 90 ) Max. Chamfer ØD 8. 9. 0.0 0..0..0..0. fab TiN coated GH-Q-M-070 GH-Q-M-07 GH-Q-M-07 GH-Q-M-07 GH-Q-M-074 GH-Q-M-07 GH-Q-M-076 GH-Q-M-077 GH-Q-M-078 GH-Q-M-079 GH-Q-M-070 * Non-stock standard item with extended delivery time 4 bco TiN coated* GH-Q-M-070 GH-Q-M-07 GH-Q-M-07 GH-Q-M-07 GH-Q-M-074 GH-Q-M-07 GH-Q-M-076 GH-Q-M-077 GH-Q-M-078 GH-Q-M-079 GH-Q-M-070 6 7. 8. 8. 8.6 9.4 9.8 0. 0. B C..4.6.6.6.8.8.8.8.8.8 H.0.0.0.0.0.0.0.0.0.0.0 PROGRMMING SPRE PRTS 7 CHNGE BLDES 9.860.9900 www.heuletool.com -860-9900 www.heuletool.com 9
Chamfering Tools For holes.0-0.0.47 -.7 Spare Parts Minimum Hole Ø.0.47..49.0... 4.0. 4..7.0.9..60 6.0.60 6..60 7.0.669 7..689.709 8..79.748 9..768 0.0.7 * Blade sold separately Tool Diameter.8.46..484.8.04..4.8.4 4..6 4.8.8..60.8.6 6..64 6.8.66 7..68 7.8.70 8..70 8.8.740 9..760 9.8.780 Tool Holder -47-49 - - - -7-9 -60-60 -60-669 -689-709 -79-748 -768-7 -0740 (.) -074 (.0) -074 (.) -074 (4.0) -0744 (4.) -074 (.0) -0746 (.) -0747 (6.0) -0748 (6.) -0749 (7.0) -070 (7.) -07 () -07 (8.) -07 () -074 (9.) -07 (0.0) -076 (0.) (ØD= ØD+0.8) Blade Options* Front and Back Cutting Gs, 90, Carbide, TiN GH-Q-M- Chamfer ØD () -074-074 (.0) (.) -074-074 (.) (4.0) -074-0744 (4.0) (4.) -0744-074 (4.) (.0) -074-0746 (.0) (.) -0746-0747 (.) (6.0) -0747-0748 (6.0) (6.) -0748-0749 (6.) (7.0) -0749-070 (7.0) (7.) -070 (7.) -07 () -07-07 () (8.) -07-07 (8.) () -07-074 () (9.) -074-07 (9.) (0.0) -07 (0.0) -076 (0.) -076-077 (0.) (.0) -077-078 (.0) (.) BLDE OPTIONS -074 (4.0) -0744 (4.) -074 (.0) -0746 (.) -0747 (6.0) -0748 (6.) -0749 (7.0) -070 (7.) -07 () -07 (8.) -07 () -074 (9.) -07 (0.0) -076 (0.) -077 (.0) -078 (.) -079 (.0) 86 Spare Parts 4 6 Set Screw Spring Distance Pin Control Bolt Blade Wrench GH-H-S-09 GH-H-F-0007 GH-Q-E-00 GH-Q-E-000 See Below GH-H-S-00 Blades GH-S geometry 90 angle (a = 90 ) Max. Chamfer ØD..0. 4.0 4..0. 6.0 6. 7.0 7. 8. 9. 0.0 0..0..0 fab TiN coated GH-Q-M-0740 GH-Q-M-074 GH-Q-M-074 GH-Q-M-074 GH-Q-M-0744 GH-Q-M-074 GH-Q-M-0746 GH-Q-M-0747 GH-Q-M-0748 GH-Q-M-0749 GH-Q-M-070 GH-Q-M-07 GH-Q-M-07 GH-Q-M-07 GH-Q-M-074 GH-Q-M-07 GH-Q-M-076 GH-Q-M-077 GH-Q-M-078 GH-Q-M-079 * Non-stock standard item with extended delivery time 4 bco TiN coated* GH-Q-M-0740 GH-Q-M-074 GH-Q-M-074 GH-Q-M-074 GH-Q-M-0744 GH-Q-M-074 GH-Q-M-0746 GH-Q-M-0747 GH-Q-M-0748 GH-Q-M-0749 GH-Q-M-070 GH-Q-M-07 GH-Q-M-07 GH-Q-M-07 GH-Q-M-074 GH-Q-M-07 GH-Q-M-076 GH-Q-M-077 GH-Q-M-078 GH-Q-M-079 6 0. 0.7.0..0..8.0..6 4.0 4. 4. 4.8.0.4.6 6.0 6.4 6.6 B C..8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8 H.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0 PROGRMMING SPRE PRTS 77 CHNGE BLDES 94.860.9900 www.heuletool.com -860-9900 www.heuletool.com 9
0 Chamfering Tools For holes 0.0 -.0.7 -.78 0 Spare Parts 0 Minimum Hole Ø 0.0.7.0..0.866.0.906 4.0.94.0.984 6.0.04 7.0.06.0.4 0.0.8.0.0.0.60.0.99 4.0.9.0.78 Tool Diameter 9.8.780 0.8.89.8.88.8.898.8.97 4.8.976.8.06 6.8.0 7.8.094 8.8.4 9.8.7 0.8..8..8.9.8. 4.8.70 Tool Holder* 0-0.0 0-.0 0-.0 0-.0 0-4.0 0-.0 0-6.0 0-7.0 0-0- 0-0.0 0-.0 0-.0 0-.0 0-4.0 0-.0 * Blade sold separately * Non-stock standard item with extended delivery time (ØD= ØD+0.8) Blade Options* Front and Back Cutting Gs,90, Carbide, TiN GH-Q-M- and Chamfer ØD () -0770 (.0) -077 (.0) -077 (.0) -077 (.0) -077 (.0) -077 (4.0) -077-077 -0774 (.0) (4.0) (.0) -077 (4.0) -0774 (.0) -0774 (.0) -077 (6.0) -077 (6.0) -0776 (7.0) -077-0776 -0777 (6.0) (7.0) () -0776-0777 -0778 (7.0) () () -0777-0778 -0779 () () (0.0) -0778-0779 -0780 () (0.0) (.0) -0779-0780 -078 (0.0) (.0) (.0) -0780-078 -078 (.0) (.0) (.0) -078-078 -078 (.0) (.0) (4.0) -078-078 -0784 (.0) (4.0) (.0) -078-0784 -078 (4.0) (.0) (6.0) -0784-078 -0786 (.0) (6.0) (7.0) -078-0786 -07 (6.0) (7.0) () Spare Parts 0 4 6 Set Screw Spring Distance Pin Control Bolt Blade Wrench GH-H-S-09 GH-H-F-00 GH-Q-E-00 GH-Q-E-000 See Table GH-H-S-00 Blades 0 GH-S geometry 90 angle (a = 90 ) Max. Chamfer ØD.0.0.0 4.0.0 6.0 7.0 0.0.0.0.0 4.0.0 6.0 7.0 fab TiN coated GH-Q-M-0770 GH-Q-M-077 GH-Q-M-077 GH-Q-M-077 GH-Q-M-0774 GH-Q-M-077 GH-Q-M-0776 GH-Q-M-0777 GH-Q-M-0778 GH-Q-M-0779 GH-Q-M-0780 GH-Q-M-078 GH-Q-M-078 GH-Q-M-078 GH-Q-M-0784 GH-Q-M-078 GH-Q-M-0786 GH-Q-M-07 * Non-stock standard item with extended delivery time bco TiN coated* GH-Q-M-0770 GH-Q-M-077 GH-Q-M-077 GH-Q-M-077 GH-Q-M-0774 GH-Q-M-077 GH-Q-M-0776 GH-Q-M-0777 GH-Q-M-0778 GH-Q-M-0779 GH-Q-M-0780 GH-Q-M-078 GH-Q-M-078 GH-Q-M-078 GH-Q-M-0784 GH-Q-M-078 GH-Q-M-0786 GH-Q-M-07 4 7.0 7. 8. 0.0 0..0..0. 4.0 4..0. 7.0 7. 8. 6 B C 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0.................. H.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0 PROGRMMING SPRE PRTS 79 CHNGE BLDES 96.860.9900 www.heuletool.com -860-9900 www.heuletool.com 97
CS Cassette Chamfering Tools CS Cassette Chamfering Tools Slim Line Cassette Easy Incorporation with Various Multi-Tasking Tools while Producing Quality Front & Back Chamfers New Slim Line Cassette with GS geometry cutting blade. The Cassette is the smallest standard cassette Heule makes, measuring thick and 0 long. The advantage of the Slim Line Cassette is it can easily be incorporated into various multi-tasking tools, including drills, boring tools and other state of the art technology. Cassette The benefits are using Heule s quality front and back chamfer system with the industry s best hole making technology. The part number for the cassette is GH-Q-O-40. bore - Ød. X + 0.0-0.0-0. 7. Minimum Bore Ød Maximum Chamfer ØDmax Maximum Tool Diameter Calc. of the X offset 0-80 (Specials on request down to Ø.6) M +0. +0 Ø 6. + 0.0 Ød ØD ØD x 0. + 0. Reference Hole Diameter Over Blade Dia. Chamfer Diameter Tool Diameter Offset from Center 0.0 +0. + 4. +0 4x R.0 ØDmax= Ød+ Max = Bore Ød - 0. X=BORE Dia (Ød) 7. BLDE OPTIONS 8 Blade Options: Cassette Blades are available from stock as front and back cutting (fab) or back only cutting (bco). Chamfer 0. x 4º.0 x 4º C. GS Geometry 90º Carb-TilN 7.0 C Front & Back GH-Q-M- -0770-077 Back Only GH-Q-M- -770-77 Chamfer Spare Parts CSS; Order Number Complete GH-Q-O-40* 6. 6.6 C..8 0. x 90º.0 x 90º DF Geometry 90º Carbide-TilN Front & Back GH-Q-M- -0780* -078* Back Only GH-Q-M- -780* -78* 4 6 Blade* Bolt Spring Distance Pin Screw Set Screw See bove GH-Q-E-0008 GH-H-F-007 GH-Q-E-0046 GH-H-S-07 GH-H-S-0 *Blade sold separately. 90º. *Extended delivery 4 6 C 4º PROGRMMING. 0º 6. 6.8 7 C..8 SPRE PRTS 8 CHNGE BLDES 98.860.9900 www.heuletool.com -860-9900 www.heuletool.com 99
CS Cassette Chamfering Tools CS Cassette Chamfering Tools Cassette Large Bore Chamfering and Multi-Tasking is easy with Heule s Cassette The Cassette makes it possible to deburr larger holes quickly and efficiently and is also available from stock. New blade options include both DF and GS geometries. Large chamfer up to.060 (.) is possible. Use DF geometry for materials above 8Rc. The part number for the cassette is GH-Q-O-00. Cassette Ød ØD ØD x Reference Hole Diameter Over Blade Dia. Chamfer Diameter Tool Diameter Offset from Center Minimum Bore Ød Maximum Chamfer ØDmax Maximum Tool Diameter Calc. of the X offset ØDmax= Ød+.0 Max = Bore Ød -.0 X=BORE Dia (Ød) 40 BLDE OPTIONS 8 7.0 Blade Options: Cassette : Blades are available from stock as front and back cutting (fab) or back cutting only (bco). Maximum Chamfer DEF Front & Back Spare Parts Cassette B F G 0. 0.00 6 0.60 0 0.94 9. 0.74 0.4.0 0.09 6. 0.60 0 0.94 9. 0.74 0.4. 0.09 6. 0.60 0 0.94 9. 0.74 0.4 *Note: GS chamfer range can vary more than DF geometry. 4 DEF Back Only H.0 0.97.0 0.97.0 0.97 DEF front and back cutting 90 Carb-TiN GH-Q-M-090 GH-Q-M-0904 GH-Q-M-0907 GS Front & Back DEF back cutting only 90 Carb-TiN GH-Q-M-09 GH-Q-M-094 GH-Q-M-097 4 Cassette Set Screw Spring Control Bolt Blade Cap Screw GH-H-S-00 GH-H-F-00 GH-Q-E-000 See bove GH-H-S-00 PROGRMMING GS front and back cutting 90 Carb-TilN GH-Q-M-080 GH-Q-M-08 GH-Q-M-08 SPRE PRTS 8 CHNGE BLDES 00.860.9900 www.heuletool.com -860-9900 www.heuletool.com 0
Tooling for Coon Tap Holes 8 Special Blade Options DEF Geometry Tooling for Coon Tap Holes Deburring For holes -8 (0.97 through. ) Drill +0. Tool Dia. -0 Order Tap/Pitch Number M6-.0.0 (.97) -.0 4.9 /4-0. (.0) -.0 4.9 M7-.0 6.0 (.6) -6.0.9 /6-8 6. (.7) -6. 6.4 M8-. 6.7 (.64) -6. 6.4 /8-6 7.9 (.) -7. 7.4 Deburring Extended Range For holes 8-0. (0.6 through.00 ) Drill +0. Tool Dia. -0 Order Tap/Pitch Number M0-. 8.4 (.) - 7.9 M0-. 8.7 (.44) -8. 8.4 7/6-4 9. (.68) - 8.8 7/6-0 9.9 (.9) -9. 9. M-.7 0. (.406) -0.0* 9.8 / - 0.7 (.4) -0.* 0. L 88 88 88 88 88 88 L 98 98 98 98 07 07 NL 4. 4. 4. 40 40 40 NL...... SL 8 8 8 8 8 8 SL 8 8 8 8 47 47 Shank ØS Ø8 Ø8 Ø8 Ø8 Ø8 Ø8 Shank ØS Ø0 Ø0 Ø0 Ø0 Ø Ø 4 6 4 6 Set Screw Spring Distance Pin Control Bolt Blade Wrench GH-H-S-07 GH-H-F-009 GH-Q-E-004 GH-Q-E-0008 See bove GH-H-S-0 GH-H-S-07 GH-H-F-009 GH-Q-E-0068 GH-Q-E-0008 See bove GH-H-S-0 GH-H-S-07 GH-H-F-009 GH-Q-E-0067 GH-Q-E-0008 See bove GH-H-S-0 ØD=ØD+0.6 +0/-.00 Blade**, Carbide-TiIN, 90, fab Chamfer (ØD) Order Number 6. 7.0 7. 8. 8. 0.0 (.6) (.76) (.9) (.) (.) (.94) GH-Q-M-006 GH-Q-M-007 GH-Q-M-008 GH-Q-M-00 GH-Q-M-00 GH-Q-M-0 ØD=ØD+0.6 +0/-.00 Blade**, Carbide-TiIN, 90, fab Chamfer (ØD) Order Number 0..0..0..0 (.4) (.4) (.4) (.47) (.49) (.) GH-Q-M-04* GH-Q-M-0* GH-Q-M-06* GH-Q-M-07* GH-Q-M-08 GH-Q-M-09 ttainable chamfer size depends on material, blade force and feed rate. Not recoended for materials above 8Rc *Non-stock standard item with extended delivery time **Blade sold separately Spare Parts Order Number -.0-7. -- -0.0-0. PROGRMMING CHNGE BLDES 8 DEF Geometry 90 angle* (a = 90 ) Max. Chamfer 8. 9. 0.0 0..0..0..0. Front & Back Chamfering fab TiN coated GH-Q-M-00 GH-Q-M-0 GH-Q-M-0 GH-Q-M-0 GH-Q-M-04 GH-Q-M-0 GH-Q-M-06 GH-Q-M-07 GH-Q-M-08 GH-Q-M-09 GH-Q-M-00 bco TiN coated GH-Q-M-00 GH-Q-M-0 GH-Q-M-0 GH-Q-M-0 GH-Q-M-04 GH-Q-M-0 GH-Q-M-06 GH-Q-M-07 GH-Q-M-08 GH-Q-M-09 GH-Q-M-00 Back Only Chamfering 7. 8. 8. 8.6 9.4 9.8 0. 0. B C G Blade Options There are different blade options for the tool if an application requires a different chamfer than the standard 90 blade. The 60 blades offer a 60 angled chamfer instead of the standard 90 angled chamfer while the DEF geometry blades provide precision chamfering and handles larger burr formation...4.6.6.6.8.8.8.8.8.8 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. H.0.0.0.0.0.0.0.0.0.0.0 F BLDE OPTIONS 7 0.860.9900 www.heuletool.com -860-9900 www.heuletool.com 0
Special Blade Options DEF Geometry Technical Instructions DEF Geometry 90 angle* (a = 90 ) Max. Chamfer..0. 4.0 4..0. 6.0 6. 7.0 7. 8. 9. 0.0 0..0..0 Front & Back Chamfering fab TiN coated GH-Q-M-040 GH-Q-M-04 GH-Q-M-04 GH-Q-M-04 GH-Q-M-044 GH-Q-M-04 GH-Q-M-046 GH-Q-M-047 GH-Q-M-048 GH-Q-M-049 GH-Q-M-00 GH-Q-M-0 GH-Q-M-0 GH-Q-M-0 GH-Q-M-04 GH-Q-M-0 GH-Q-M-06 GH-Q-M-07 GH-Q-M-08 GH-Q-M-09 *Non-stock standard item with extended delivery time bco TiN coated GH-Q-M-040 GH-Q-M-04 GH-Q-M-04 GH-Q-M-04 GH-Q-M-044 GH-Q-M-04 GH-Q-M-046 GH-Q-M-047 GH-Q-M-048 GH-Q-M-049 GH-Q-M-00 GH-Q-M-0 GH-Q-M-0 GH-Q-M-0 GH-Q-M-04 GH-Q-M-0 GH-Q-M-06 GH-Q-M-07 GH-Q-M-08 GH-Q-M-09 0. 0.7.0..0..8.0..6 4.0 4. 4. 4.8.0.4.6 6.0 6.4 6.6 Back Only Chamfering B C G..8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8.8 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. 7. H.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0 F djusting the Chamfer Size Chamfer size is based on the size of the blade. The maximum possible chamfer size is between 0. and. per side depending on the blade size. The maximum chamfer size may not be possible when cutting harder materials such as those with hardness Rc>0 or exotic alloys. Setting the Blade Force The blade force can be adjusted with the set screw in the end of the shank. The blade force should be enough to ensure the blade extends completely after passing through the bore. Changing the blade force does not change the chamfer size. Increase the blade force by turning the set screw clockwise Decrease the blade force by turning the set screw counter-clockwise. Working with the correct blade pressure increases the blade life and improves the chamfer quality. If a very strong blade force is required, the harder spring can be inserted into the tools of and groups (not standard). Harder spring for is GH-H-F-004 Harder spring for is GH-H-F-00 dd suffix -HS for complete tool (ie. -4-HS) Changing Blades The blade change in the tool is quick and easy. There are no tools required and it can be done with the tool in the spindle. Remove the blade by simply pushing it past center and out the back of the tool. Install the new blade by pushing the back side of the blade through the window until it snaps. The tool is ready to run. 04.860.9900 www.heuletool.com -860-9900 www.heuletool.com 0
Prograing Information Prograing Information Prograing Information For Front & Back Chamfer Step : Set the RPM according to the suggested values. Step : (Move into position) Move the tool with rapid feed into position with the front. Step : (Cut front chamfer) Machine the part with cutting feed (cf) and speed (cs). Feed into the part the chamfer depth + 0.040 to ensure the tool is finished cutting. Step 4: (Rapid through part) Move the tool through the part with rapid feed until the blade is 0.040 beyond burr. The blade will not damage the through hole. Step : (Cut back chamfer) Machine the part with cutting feed (cf) and speed (cs). Feed into the part the chamfer depth + 0.040 to ensure the tool is finished cutting. Step 6: (Remove from the part) Remove the tool from the part with a rapid feed and proceed to the next hole. The blade will not damage the through hole. Back Chamfer Only Prograing Information (continued) Material luminum Brass Low Carbon Steels Med Carbon Steels Free Machining lloys Stainless Steel Gray Cast Iron Nodular Cast Iron Short Chipping Iron Titanium Important Note: Tool holder must be modified with blade locking mechanism for spindle speeds above 6,000 rpm. Please contact Heule Tool Corporation Engineering Department. Optional Locking Mechanism Configuration for Standard Tool Holders When Ordering please use a suffix -LM after the standard order number. Locking mechanism allows for higher RPM. Spring LM IPR (- GS) 0.006-0.0 0.006-0.04 0.004-0.008 0.004-0.009 0.004-0.006 0.00-0.00 0.004-0.008 0.00-0.007 0.00-0.007 0.00-0.00 Distance Pin LM IPR (- DF) 0.00-0.00 0.00-0.00 0.00-0.00 0.00-0.00 0.00-0.00 0.00-0.00 0.00-0.00 0.00-0.00 0.00-0.00 0.00-0.00 L L L L4 Order Example of Tooling with Locking Mechanism - 8 - - LM LM Indicates Tooling with Locking Mechanism Cap Screw LM DIMENSIONS () PRT NUMBER Tooling Size () L L L L4 Cap Screw - LM Distance Pin - LM Spring- LM.0 7..8 6. 9. GH-H-S-08- GH-Q-E-0089 GH-H-F-00 8 9. 6.8 7. 9. GH-H-S-08- GH-Q-E-0090 GH-H-F-00 0 0. 7.8 80. 9. GH-H-S-08- GH-Q-E-009 GH-H-F-00 8 8 7.9 8.4 4 GH-H-S-04- GH-Q-E-009 GH-H-F-00 0 9. 0 4 GH-H-S-04- GH-Q-E-0094 GH-H-F-00 Important Note: Tool holder must be modified for locking mechanism components. SFM 400-600 0-400 00-80 7-00-80 0-0-0 0-0 00-0 40-80 06.860.9900 www.heuletool.com -860-9900 www.heuletool.com 07
Troubleshooting PROBLEM Chamfer too small No chamfer at all Chamfer is too large Chamfer differs from front to back Poor surface finish Inconsistent chamfer Poor blade life (chipping) (excessive wear) EXPLNTION Selected blade is too small Blade force is too small Feed rate is too high Tool is incorrectly prograed Blade force is too small Blade is dull Too heavy of a burr Selected blade is too large Feed rate too small Blade force too high Feed varies between forward and reverse feed Variation of burr between front and back Tool or part not held properly Tool is unstable Speed rate is too high Varying feed rate Incorrect prograing position Tool is unstable Workpiece or tool not secured Insufficient machine stability Poor cutting conditions SOLUTION Choose larger blade (if possible) Increase blade force Reduce feed rate Check prograing depths Increase blade force Replace the blade Replace the drill tool Choose a smaller blade Increase the feed rate Reduce the blade force Use DF geometry Select a constant feed rate Reduce the feed rate when too small or increase feed rate when too large Increase blade tension Ensure tool and part are secured Reduce Speed Check workpiece and holder Ensure constant feed rate Check workpiece and holder Check prograing Reduce Speed Ensure tool or part is secured Recondition or rectify machine faults Check speed and feed and coolant supply Grinding may produce hazardous dust. To avoid adverse effects, use adequate ventilation and read MSDS. Cutting tools may break during use. To avoid injury, use proper safety precautions and protective equipment. Use the machine tool with sufficient rigidity and horsepower. Use a cover on a machine tool and protector, such as glasses, against shattering chips and broken tools due to misuse. Do not use insoluble oil because there is a danger of causing fire. VEX-S Combination Drill with Front & Back Chamfering of Through Holes High performance solid carbide drill tip combined with patented chamfering system VEX drill geometry for better chip control Quick and easy drill tip and chamfer blade replacement No presetting between drill changes 08.860.9900 www.heuletool.com Cat. No. HTC08