Technical Data Sheet 0.8mm Height Flat Top Infrared LED Features Small double-end package Low forward voltage Good spectral matching to Si photo detector Package in 8mm tape on 7 diameter reel Pb free The product itself will remain within RoHS compliant version. Descriptions is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with flat top view lens. The device is spectrally matched with silicon photodiode and phototransistor. Applications PCB mounted infrared sensor Infrared emitting for miniature light barrier Floppy disk drive Optoelectronic switch Smoke detector Device Selection Guide LED Part No. Chip Material Lens Color IR GaAlAs Water Clear Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 1 of 10
Package Dimensions 1 2 1 2 1 Cathode 2 Anode Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25 ) Parameter Symbol Rating Units Continuous Forward Current I F 65 ma Peak Forward Current I FP 1.0 A Reverse Voltage V R 5 V Operating Temperature T opr -25 ~ +85 Storage Temperature T stg -40 ~ +85 Soldering Temperature T sol 260 Power Dissipation at(or below) 25 Free Air Temperature P d 130 mw Notes: *1:I FP Conditions--Pulse Width 100μs and Duty 1%. *2:Soldering time 5 seconds. Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 2 of 10
Electro-Optical Characteristics (Ta=25 ) Parameter Symbol Condition Min. Typ. Max. Units I F =20mA 0.2 0.7 Radiant Intensity Ee I F =100mA mw /sr -- 4.0 -- Pulse Width 100μs,Duty 1% Peak Wavelength λp I F =20mA -- 940 -- nm Spectral Bandwidth Δλ I F =20mA -- 45 -- nm I F =20mA -- 1.2 1.5 Forward Voltage V F I F =100mA Pulse Width 100μs,Duty 1% -- 1.4 1.8 V I F =1A -- 2.6 4.0 Reverse Current I R V R =5V -- -- 10 μa View Angle 2θ1/2 I F =20mA -- 150 -- deg Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 3 of 10
Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Fig.2 Spectral Distribution Ambient Temperature 140 120 100 80 60 40 20 0-25 0 20 40 60 80 100 100 80 60 40 20 0 IF=20mA Ta=25 C Fig.3 Peak Emission Wavelength Ambient Temperature 980 Fig.4 Forward Current vs. Forward Voltage 10 4 960 940 920 3 10 10 2 900-25 0 25 50 75 100 10 1 0 1 2 3 4 Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 4 of 10
Typical Electro-Optical Characteristics Curves Fig.5 Relative Intensity vs. Fig.6 Relative Radiant Intensity vs. Forward Current Angular Displacement 100-20 -10 0 10 20 Ie-Radiant Intensity(mW/sr) 10 1 1.0 0.9 0.8 0.7 30 40 50 60 70 80 0 10 0 1 2 3 10 10 10 IF-Forward Current (ma) 10 4 0.6 0.4 0.2 0 0.2 0.4 0.6 Fig.7 Relative Intensity vs. Ambient Temperature( C) 0.9 Fig.8 Forward Voltage vs. 1.3 Ambient Temperature( C) 0.7 IF=20mA 1.2 IF=20mA 0.5 1.1 0.3 25 50 75 100 120 1 25 50 75 100 120 Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 5 of 10
Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 6 of 10
4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 7 of 10
Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level:90% LTPD:10% NO. Item Test Conditions Test Hours/ Cycles Sample Sizes Failure Judgement Criteria Ac/Re 1 REFLOW Soldering TEMP.:260 ±5 6Mins 22pcs 0/1 5secs I R U 2 2 Temperature Cycle H : +100 15mins 50Cycles 22pcs Ee L 0.8 0/1 5mins V F U 1.2 L : -40 15mins 3 Thermal Shock H :+100 5mins 10secs 50Cycles 22pcs U:Upper Specification 0/1 L :-10 5mins Limit 4 High Temperature TEMP.:+100 1000hrs 22pcs L:Lower 0/1 Storage Specification 5 Low Temperature Storage TEMP.:-40 1000hrs 22pcs Limit 0/1 6 DC Operating Life I F =20mA 1000hrs 22pcs 0/1 7 High Temperature/ High Humidity 85 / 85% R.H 1000hrs 22pcs 0/1 Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 8 of 10
Package Dimensions Taping Dimensions 1 2 1 Cathode 2 Anode Unit:mm Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 9 of 10
Packing Quantity Specification 1.3000Pcs/1Volume,1Volume/1Bag 2.10Boxes/1Carton Label Form Specification RoHS CPN: Customer s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength EF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don t reproduce or cause anyone to reproduce them without EVERLIGHT s consent. EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936 Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306 Tucheng, Taipei 236, Taiwan, R.O.C http:\\www.everlight.com Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 2 Page: 10 of 10