Product catalog May 2010
T E L I O N 1 3 0 0 T R A N S C E I V E R M I L I T A R Y U S E Fully Digital Software Defined Radio Transceiver Capable of supporting virtually any type of waveform Provides ARDS-compliant Participant functionality, Pushto-Talk (various rates up to 1000 Slots/sec) Can be powered up from as low as 3.6VDC power supply High Data Rate (capable of up to 6.5 Mbps) Variety of user data interfaces of the same hardware Telion-1300 fully digital, spread spectrum software defined radio, board level E L E C T R O M E C H A N I C A L Input voltage range: 3.6 36 VDC Operating temperature range: -40 +80 deg C Humidity: up to 95%, non-condensing RF connector: MCX Board level transceiver provides 30-pin data connector Data Interfaces: Serial, SDLC, Ethernet Dimensions (board level) 3.18 x 2.89 x 0.47, fits PC/104 8/16-bit carrier boards
T E L I O N 1 3 0 0 T R A N S C E I V E R C H A R A C T E R I S T I C S Frequency band of operation RF channel throughput Signal OC-BW Modulation types supported Error correction Error detection Interleaving/ De-interleaving Network topologies supported RF Network security RF channel data encryption Dimensions (board level) 1350 1390 MHz, 25 khz spacing Defined by the loaded software: 1.2 Mb/s for ARDS waveform; Up to 1.2 Mb/s otherwise, capable of 6.5 Mbps. Dependent upon the type of modulation and RF bit rate selected. SOQPSK (ARDS-compliant), MSK, GMSK, FSK, capable of BPSK, QPSK. Convolutional code (r =1/2), Viterbi soft decision, k =7. Transceiver can support user-defined CRC protocol. Several standard protocols are supported CRC16 (default) CRC24 (MIL-STD 188-184), CRC32 matrix Interleaver/De-Interleaver TDMA, Push-to-Talk, Point-to-Point, Point-to- Multipoint, TDMA (including Masterless TDMA) The following parameters are user selectable; Hop rate as fast as 100,000 per second; Fast frequency hopping option; Number of data bytes within each RF packet; Deviation/modulation index for the RF Xmit; Hop table up to 128 frequency channels long; Each frequency channel is user selectable. Available cryptography: AES, DES, and 3DES algorithms. User-defined security keys. 3.18 x 2.89 x 0.47.
T I A M I S - 8 0 0 T R A N S C E I V E R F O R S E R I A L I N T E R F A C E S Fully digital, software defined radio transceiver Tiamis-800, software defined radio transceiver, extruded aluminum enclosure Supports almost any type of RF channel waveform (FM, PM, or AM); On-board encryption engine, randomizer, and encoder; If needed, can be used with external up/ down frequency converter or power amplifier to meet CDL requirements RF channel throughput adjustable according to the application needs from 2.4 kb/s to 1 Mb/s; Wide selection of data interfaces Spreading Spectrum by Frequency Hopping (hops as fast as 100,000 times/second), or Direct Sequence, or Hybrid User selectable frequency channels of operation with resolution of 0.25 khz; Operation Frequency Band is 824-960 MHz providing operation in almost any part of the world R E L A T E D P R O D U C T S Board level Tiamis-800 software defined radio transceiver Lexycom Configuration and Firmware Upgrade programs Interchangeable data interface Serial data options: Option 1100, 1102, 1103 Ethernet data options: Option 1200 Board level Antennas Cables
T I A M I S - 8 0 0 T R A N S C E I V E R C H A R A C T E R I S T I C S Frequency band of operation RF channel throughput Network topologies supported RF Network security RF channel data encryption Output power Sensitivity Input voltage range Operating temperature range Humidity RF connector Data interfaces supported Dimensions (board level) 824 960 MHz User selectable: from 1200 b/s to 256 kb/s for 2- level modulation schemas; up to 1 MB/s for more complex modulation types. Point-to-Point, Point-to-Multipoint, TDMA, Peer-to-Peer. In addition to the proprietary network protocol that is used, the following parameters of the transceiver are user selectable, providing required network security: Hop Rate as fast as 100,000 times per second; Fast frequency hopping option; Hop table up to 128 frequency channels long. Each frequency channel is user selectable with 0.25 khz resolution. Available cryptography: AES, DES, and 3DES algorithms. User-defined security keys. Programmable with 1 db steps, up to 1 Watt. -109 dbm @ BER 10^-6, RF channel bit rate of 130 kb/s, 2 level FSK 4.5 25 VDC. -35 + 80 deg C. Up to 90%, non-condensing. SMA With the appropriate interface board, the transceiver is capable of supporting the following data interfaces: RS232, RS422, RS485, USB, I2C, SPI, Ethernet, and Digital I/Os. 3 x 6.45 x 0.5.
T I A M I S - 8 0 0 L T R A N S C E I V E R F O R S E R I A L I N T E R F A C E S Frequency band 902-928 MHz Network Topologies: Point-to-Point, Point-to-Multipoint, TDMA, Peer-to-Peer Single Radio Repeater Tiamis-800L, software defined radio transceiver, extruded aluminum enclosure Data Encryption: AES, DES, and 3DES RF Channel throughput 130 kb/s On board firmware bank Selectable hop tables User Interchangeable data interface Output Power up to 1 Watt Minimum operating voltage is as low as 4.5 VDC R E L A T E D P R O D U C T S Tiamis-800L, software defined, board level, radio transceiver when equipped with Option 1100, Option 1102, or Option 1103. Interchangeable data interface Serial data options: Option 1100, 1102, 1103 Ethernet data options: Option 1200 Board level Accessories Antennas Cables
T I A M I S - 8 0 0 L T R A N S C E I V E R C H A R A C T E R I S T I C S Frequency band of operation RF channel throughput 902 928 MHz 130 kb/s Network topologies supported RF Network security Point-to-Point, Point-to-Multipoint, TDMA, Peer-to-Peer In addition to the proprietary network protocol that is used, the following parameters of the transceiver are user selectable, providing required network security: Hop table up to 128 frequency channels long. Number of data bytes in each RF packet RF channel data encryption Output power Sensitivity Input voltage range Operating temperature range Humidity RF connector Data interfaces supported Dimensions (board level) Available cryptography: AES, DES, and 3DES algorithms. User-defined security keys. Programmable with 1 db steps, up to 1 Watt. -110 dbm @ BER 10^-6, RF channel bit rate of 130 kb/s, 2 level FSK 4.5 25 VDC. -35 + 80 deg C. Up to 90%, non-condensing. SMA With the appropriate interface board, the transceiver is capable of supporting the following data interfaces: RS232, RS422, RS485, USB, I2C, SPI, Ethernet, and Digital I/Os. 3 x 6.45 x 0.5.
O P T I O N 1 1 0 0 F O R S E R I A L I N T E R F A C E S Supports up to two independent RS232 data channels Supports the Lexycom proprietary Intelligent Interface Type Recognition protocol Supports Setup/Diagnostics mode and the Firmware Banks Exchange algorithm Option 1100 - single RS232 and diagnostics port interface board User Interchangeable Attaches/piggybacks to the Tiamis-800 series Minimum operating voltage is as low as 4.5 VDC +/- 15 kv ESD protection (using HBM) Equipped with the push-button setup switch Sold separately or as a complete assembly with the Tiamis-800 series transceiver Tiamis-800 transceiver with Option 1100 - interface board I N T E R F A C E O P T I O N S Option 1100 - RS232 Interface, single channel, for use with board level product Option 11E0 - RS232 Interface, single channel, for use with enclosure product Option 1104 - RS232 Interface, dual channel, includes two RS232 channels, for use with board level product Option 11E4 - RS232 Interface, dual channel, includes two RS232 channels, for use with enclosure product
O P T I O N 1 1 0 0 C H A R A C T E R I S T I C S Data interface supported Connectors Setup/Diagnostics support Firmware Banks exchange protocol support Support of the Intelligent Interface Type Recognition protocol Data rates supported Data format supported Data port diagnostics support ESD protection Flow control Additional functions Mechanical dimensions Means of connecting to the Tiamis-800 transceiver Operating voltage range Operating temperature range Humidity Two independent RS232 data channels Data ports - DB-9 Power - 4 pin, 0.1 spacing straight connector Data2 port can be used as the setup/diagnostics port Yes Yes Up to 115.2 kb/s 5, 6, 7,and 8 Data Bits Even, Odd, and None Parity 1, 1.5, and 2 Stop Bits Local or remote loops are supported +/-15 kv using HBM CTS line indicates the status of the data buffer Equipped with a push-button Setup switch to force the transceiver into the setup mode. 3(W) x 3.41(L) x 0.625(H) inches Uses five #2 hardware screws with aluminum standoffs (supplied with the interface board). 4.5 25 VDC -35 + 80 deg C Up to 90%, non-condensing
O P T I O N 1 1 0 2 F O R S E R I A L I N T E R F A C E S Support one RS422 data channel and one RS232 data/ diagnostics channel Supports the Lexycom proprietary Intelligent Interface Type Recognition protocol Supports Setup/Diagnostics mode and the Firmware Banks Exchange algorithm Option 1102 - single RS422 and diagnostics port interface board User Interchangeable Attaches/piggybacks to the Tiamis-800 Minimum operating voltage is as low as 4.5 VDC Equipped with the push-button setup switch Sold separately or as a complete assembly with the Tiamis-800 transceiver Tiamis-800 transceiver with Option 1102 - interface board I N T E R F A C E O P T I O N S Option 1102 - RS422 Interface, single channel, for use with board level product Option 11E2 - RS422 Interface, single channel, for use with enclosure product Option 1106 - RS422 Interface, dual channel, includes one RS232 channel, for use with board level product Option 11E6 - RS422 Interface, dual channel, includes one RS232 channel, for use with enclosure product
O P T I O N 1 1 0 2 C H A R A C T E R I S T I C S Data interface supported Connectors Setup/Diagnostics support Firmware Banks exchange protocol support Support of the Intelligent Interface Type Recognition protocol Data rates supported Additional functions Mechanical dimensions Means of connecting to the Tiamis-800 transceiver Operating voltage range Operating temperature range Humidity One RS422 data channel and one additional (optional) RS232 data channel Data port and diagnostics port - DB-9 Power - 4 pin, 0.1 spacing straight connector Dedicated diagnostics port Yes Yes Up to 115.2 kb/s Equipped with a push-button Setup switch to force the transceiver into the setup mode. 3(W) x 3.41(L) x 0.625(H) inches Uses five #2 hardware screws with aluminum standoffs (supplied with the interface board). 4.5 25 VDC -35 + 80 deg C Up to 90%, non-condensing
O P T I O N 1 1 0 3 F O R S E R I A L I N T E R F A C E S Supports one RS485 data channel and one RS232 data/ diagnostics channel Supports the Lexycom proprietary Intelligent Interface Type Recognition protocol Supports Setup/Diagnostics mode and the Firmware Banks Exchange algorithm Option 1103 - single RS485 and diagnostics port interface board User Interchangeable Attaches/piggybacks to the Tiamis-800 Minimum operating voltage is as low as 4.5 VDC Equipped with the push-button setup switch Sold separately or as a complete assembly with the Tiamis-800 transceiver Tiamis-800 transceiver with Option 1103 - interface board I N T E R F A C E O P T I O N S Option 1103 - RS485 Interface, single channel, for use with board level product Option 11E3 - RS485 Interface, single channel, for use with enclosure product Option 1107 - RS485 Interface, dual channel, includes one RS232 channel, for use with board level product Option 11E7 - RS485 Interface, dual channel, includes one RS232 channel, for use with enclosure product
O P T I O N 1 1 0 3 C H A R A C T E R I S T I C S Data interface supported Connectors Setup/Diagnostics support Firmware Banks exchange protocol support Support of the Intelligent Interface Type Recognition protocol Data rates supported Additional functions Mechanical dimensions Means of connecting to the Tiamis-800 transceiver Operating voltage range Operating temperature range Humidity One RS485 data channel and one additional (optional) RS232 data channel Data port and diagnostics port - DB-9 Power - 4 pin, 0.1 spacing straight connector Dedicated diagnostics port Yes Yes Up to 115.2 kb/s Equipped with a push-button Setup switch to force the transceiver into the setup mode. 3(W) x 3.41(L) x 0.625(H) inches Uses five #2 hardware screws with aluminum standoffs (supplied with the interface board). 4.5 25 VDC -35 + 80 deg C Up to 90%, non-condensing
O P T I O N 1 1 0 8 E T H E R N E T - S E R I A L S E R V E R Legacy serial devices are now IP addressable with the Ethernet/Serial server Provides Ethernet connectivity for RS232, RS422, and RS485 equipment Ethernet-to-serial server handles all required protocol conversion Option 1108- Ethernet /Serial Server and diagnostics port interface board Supports the Lexycom proprietary Intelligent Interface Type Recognition protocol Supports Setup/Diagnostics mode and the Firmware Banks Exchange algorithm User Interchangeable, piggybacks to the Tiamis-800 Sold separately or as a complete assembly with the Tiamis-800L transceiver Tiamis-800 transceiver with Option 1108 - interface board I N T E R F A C E O P T I O N S Option 1108 - Ethernet Serial Server interface, single channel, for use with board level product Option 11E8 - Ethernet Serial Server interface, single channel, for use with enclosure product Option 110C - Ethernet Serial Server interface, dual channel, includes one RS232 channel, for use with board level product Option 11EC - Ethernet Serial Server Interface, dual channel, includes one RS232 channel, for use with enclosure product
O P T I O N 1 1 0 8 C H A R A C T E R I S T I C S Data interface supported Connectors Setup/Diagnostics support Firmware Banks exchange protocol support Support of the Intelligent Interface Type Recognition protocol Data rates supported Additional functions 10Base-T/100 Base-TX Ethernet RJ45 for Ethernet port; DB-9 for diagnostics port; Power - 4 pin, 0.1 spacing straight connector Dedicated diagnostics port Yes Yes Up to 115.2 kb/s Auto negotiates full/half duplex, 10Base-T or 100 Base-T speed. Supports UDP (datagrams 0x00, 0x01, 0x03, 0x05, and 0xFF) or TCP packets. Programmable port number and serial port settings. Supports telnet, Hosts List, AES encryption, event-driven programmable e-mail notification, MDI/MDI-X auto-crossover Extremely easy to set up and begin operating Mechanical dimensions Means of connecting to the Tiamis-800 transceiver Operating voltage range Operating temperature range Humidity 3(W) x 3.41(L) x 0.625(H) inches Uses five #2 hardware screws with aluminum standoffs (supplied with the interface board). 4.5 25 VDC -35 + 80 deg C Up to 90%, non-condensing
O P T I O N 1 2 0 0 F O R E T H E R N E T I N T E R F A C E S 10/100Base-T Ethernet Bridge; protocol transparent functionality Supports Auto-crossover, Full or Half-duplex Supports the Lexycom proprietary Intelligent Interface Type Recognition protocol Option 1200 - Ethernet and diagnostics port interface board Supports Setup/Diagnostics mode and the Firmware Banks Exchange algorithm User Interchangeable Attaches/piggybacks to the Tiamis-800 Equipped with the push-button setup switch Sold separately or as a complete assembly with the Tiamis-800 transceiver Tiamis-800 transceiver with Option 1200 - interface board I N T E R F A C E O P T I O N S Option 1200 - Ethernet Interface, single channel, for use with board level product Option 12E0 - Ethernet Interface, single channel, for use with enclosure product
O P T I O N 1 2 0 0 C H A R A C T E R I S T I C S Data interface supported Connectors Setup/Diagnostics support Firmware Banks exchange protocol support Support of the Intelligent Interface Type Recognition protocol Additional functions 10Base-T, 100Base-TX, and 100Base-T RJ45 for Ethernet port, DB-9 for diagnostics port Power - 4 pin, 0.1 spacing straight connector Dedicated diagnostics port Yes Yes Equipped with Link, Full/Half-duplex, Speed, and Collision LEDs Supports MDI/MDI-X auto-crossover Extremely easy to setup and begin operating. Requires almost no programming or user interaction auto negotiates speed, full/half duplex. Mechanical dimensions Means of connecting to the Tiamis-800 transceiver Operating voltage range Operating temperature range Humidity 3(W) x 3.41(L) x 0.625(H) inches Uses five #2 hardware screws with aluminum standoffs (supplied with the interface board). 4.5 25 VDC -35 + 80 deg C Up to 90%, non-condensing
E N C L O S U R E S F O R S E R I A L Extruded Aluminum enclosure with open plastic bezels and aluminum end plates Easy access slide off top cover Interchangeable front panel Tiamis-800 software defined radio transceiver in the enclosure when equipped with any serial data enclosure option. Single or dual data ports Equipped with toggle reset switch Enclosure design accommodates interface options RS232, RS422, RS485 Compact; 6.30 x 4.06 x 1.20 Tiamis-800 software defined radio transceiver in the enclosure when equipped with Option 11E8. Ethernet/Serial server. R E L A T E D P R O D U C T S Interchangeable data interface board Serial data options: Option 11E0, 11E4, 11E2, 11E6, 11E3, or 11E7 Interchangeable front panel Board level products Antennas Cables
E N C L O S U R E S F O R E T H E R N E T Allows the user to view, modify, and store Tiamis-800/Telion- 1300 transceiver settings Allows the user to save the settings from the transceiver into a file or load the settings from a previously stored file into the transceiver Allows the user to select the operating transceiver s firmware from the list of pre-stored programs Allows quick and easy mass-programming of transceivers for large scale systems Tiamis-800 software defined radio transceiver in the enclosure when equipped with Option 12E0 User-friendly graphical interface (Windows operating system compatible) Allows the user to restore the factory default settings Supplied by Lexycom with every transceiver purchase free of charge. The new releases are fully back compatible N E M A E N C L O S U R E K I T S Nema kits provide protection in harsh environments Non-conductive, impact resistant, UV resistant Enclosure door can be padlocked for added security Easy installation Enclosure kit only radios are ordered separately
F R O N T P A N E L S Front Panel Options for use with the Tiamis-800 series transceivers enclosure models. Front panels available for use with the interchangeable interface board enclosure product. S E R I A L ORDER OPTION: FP1100 for RS232, FP1102 for RS422 and FP1103 for RS485. Includes all front panel hardware for the Tiamis-800 series transceiver. E T H E R N E T / S E R I A L S E R V E R ORDER OPTION: FP1108 for Ethernet/Serial Server Includes all front panel hardware for the Tiamis-800 series transceiver. E T H E R N E T ORDER OPTION: FP1200 for Ethernet Includes all front panel hardware for the Tiamis-800 series transceiver.
F I R M W A R E U P G R A D E P R O G R A M F O R A L L M O D E L S Allows the user to view, erase, and upload up to 7 different firmware source codes into the Tiamis-800 transceiver s internal Flash memory Allows the user to view, erase, and upload up to 9 different firmware source codes into the Telion-1300 transceiver s internal Flash memory Provides simple and intuitive user graphical interfaces (Windows operating system compatible) Supplied by Lexycom with every Tiamis-800 transceiver purchase free of charge. The new releases are fully back compatible Starting with version 2.0, allows upgrade of the Boot sector on the radio R E L A T E D P R O D U C T S Tiamis-800, Telion-1300 SDR transceivers Lexycom Configuration Program
L E X N E T N E T W O R K D I A G N O S T I C S P R O G R A M F O R S E R I A L I N T E R F A C E S LEXNet network management software is included with all radios using serial interfaces LEXNet software allows for quick and easy network set up, management, maintenance, and troubleshooting Users are able to view, modify, and save the settings of all radios in the network remotely Data for individual radios in a network or for a complete network can be logged for a specified timeframe and then stored into a file for review LEXNet software can be run from any radio in the network ( the user is not required to be at the Master site) The Windows-based software is very intuitive with an easy to use interface On board electronic help file documentation R E L A T E D P R O D U C T S Tiamis-800 software defined radio transceiver Lexycom Firmware Upgrade program and Configuration software
L E X N E T N E T W O R K D I A G N O S T I C S P R O G R A M C H A R A C T E R I S T I C S System requirements: Windows 95 or later Requires less than 3 Mb of hard drive (includes Help file with documentation) When running, allocates less than 6 Mb of RAM Requires one of the COM ports on the computer LEXNet diagnostics is designed to operate over a point-topoint, point-to-multi-point or a TDMA network. The software provides a setup file, which automatically configures the user s computer for proper software installation. The LEXNet diagnostics software is free-of-charge and can be obtained from Lexycom s technical support staff.
C O N F I G U R A T I O N P R O G R A M F O R S E R I A L I N T E R F A C E S Allows the user to view, modify, and store Tiamis-800/ Telion-1300 transceiver settings Allows the user to save the settings from the transceiver into a file or load the settings from a previously stored file into the transceiver Allows the user to select the operating transceiver s firmware from the list of pre-stored programs Allows quick and easy mass-programming of transceivers for large scale systems User-friendly graphical interface (Windows operating system compatible) Allows the user to restore the factory default settings Supplied by Lexycom with every transceiver purchase free of charge. The new releases are fully back compatible R E L A T E D P R O D U C T S Tiamis-800, Telion-1300 SDR transceivers Lexycom Firmware Upgrade program
R F C A B L E S R F C A B L E S Cable LMR240 N-male to SMA-male connector Cable length Order Part Number 10 feet FGCA0102NS 25 feet FGCA0252NS 50 feet FGCA0502NS 100 feet FGCA1002NS Cable LMR400 N-male to SMA-male connector Cable length Order Part Number 10 feet FGCA0104NS 25 feet FGCA0254NS 50 feet FGCA0504NS 100 feet FGCA1004NS Please call for additional lengths and connector types. Note: Cable loss will impact performance. Lexycom Technologies uses a low loss cable designed for wireless applications. Please contact us for additional information. R E L A T E D P R O D U C T S Tiamis-800, Telion-1300 SDR transceivers Directional and omnidirectional antennas
D A T A & P O W E R C A B L E S D A T A C A B L E S RS232 DATA CABLES DB9M/DB9F; 6 foot length, shielded ORDER PART NUMBER: FGCA2090AA P O W E R C A B L E S POWER CABLE ADAPTOR 6 feet long, one end has a 2.1 mm center pin diameter round power connector ORDER PART NUMBER: FGCA0210KA 4PIN POWER CABLE Four wire power cable (wires are color coded). Provides power and reset function support for the Tiamis-800 transceiver when used with one of the interface boards manufactured by Lexycom ORDER PART NUMBER: ASCA0024AA WALL ADAPTOR P O W E R A D A P T O R AC-DC power wall adaptor, 800mA, 12V ORDER PART NUMBER: FGAN0800MA
A N T E N N A S D I R E C T I O N A L 6 Element Directional YAGI (10 db gain) 902-928 MHz (Enviro-Seal) ORDER PART NUMBER: FGAN0906YE Termination: Pigtail, N Female, Boom length 2.0 ft 3 Element Directional YAGI (6 db gain) 902-928 MHz ORDER PART NUMBER: FGAN0903YS Termination: Pigtail, N Female, Boom length1.1 ft All Antennas include mounting hardware
A N T E N N A S O M N I D I R E C T I O N A L 5 db OMNIDIRECTIONAL Antenna 902-928 MHz ORDER PART NUMBER: FGAN0905OS Termination: Pigtail, N Female, Overall length 30 inches Base to mast mounting hardware is included 1/2 WAVE PORTABLE Antenna P O R T A B L E 902-928 MHz, SMA Male ORDER PART NUMBER: FGAN0900PS DIPOLE Right Angle PORTABLE Antenna 890-960 MHz, SMA Male ORDER PART NUMBER: FGAN0900PD 1/2 WAVE Right Angle/Swivel PORTABLE Antenna 902-928 MHz, SMA Male ORDER PART NUMBER: FGAN0900PA
D O C U M E N T A T I O N At the time of the initial product purchase all required documentation is supplied to the users at no charge. Electronic copies of all of the documents may also be obtained from or via our technical support group. To request a paper or CD copy of any of the documents listed in this catalog, please, contact Lexycom s sales department. U S E R M A N U A L S The Tiamis-800 transceiver User Manual Paper Copy Part Number: Copy of the file on a CD Part Number: DOUM0001AB DOUM0001AC The Firmware Upgrade program User Manual Paper Copy Part Number: Copy of the file on a CD Part Number: DOFW0107MB DOFW0107MC The Configuration Program User Manual Paper Copy Part Number: Copy of the file on a CD Part Number: DOSW0114MB DOSW0114MC The Telion-1300 Documentation User Manual: DOSW0102TC Operating and Maintenance Manual Mechanical Drawings MTBF Calculation for Missile Flight&Launch Conditions