SafeDispatch TETRA Station Gateway User Guide Rev. 20160416.7008642
Gateway station CPE file MTM5400 For the gateway station you will have to change the following fields: in Subscriber Unit Parameters, you will set a value for gateway s Radio ISSI in Feature Flags, you will set the GPS will be unchecked CPS 6.2 R 06.20.09.00 Radio MTM5400 2
in PEI Parameters, you will set the Baud Rate values to 9600 Parity Bit value to PARITY_NONE Flow Control value to No flow control Stop Bits value to 1 Data Bits value to 8 in AT commands, you will set the ETSI AT SDS/Status Format will be unchecked Extended ETSI Addressing will be unchecked CPS 6.2 R 06.20.09.00 Radio MTM5400 3
User radio CPE file MTP850E GPS Settings GPS Authorized ISSI Base will be set to the Gateway s Radio ISSI value GPS Location Protocol value will be set to LRRP GPS Coordinates value will be set to Latitude/Longitude GPS in DMO value will be set to Enabled in Any DMO Mode SafeMobile Tetra Gateway Application is working only with LRRP Protocol : LRRP Configuration GPS SDS TL Disabled will be unchecked Note: TETRA radios have their GPS refresh interval set in their codeplug so the value which is setup in Subscriber and User management (Administrative module) is not used. CPS 6.2 R 06.20.09.00 Radio MTM5400 4
LRRP Profiles will be used to make subscriber radios send periodic GPS reports. LRRP Profiles: Status Profile GPS Event Location Enable will be checked GPS Event Timestamp Enable will be checked GPS LRRP Destination ISSI will be set to the Gateway s Radio ISSI value LRRP Profiles: Normal Periodic Profile GPS Event Location Enable set to TRUE (checked) GPS Event Timestamp Enable set to TRUE (checked) GPS LRRP Destination ISSI will be set to the Gateway s Radio ISSI value GPS Idle Report Period set to an integer value CPS 6.2 R 06.20.09.00 Radio MTM5400 5
LRRP Profiles: Emergency Periodic Profile GPS Event Location Enable set to TRUE (checked) GPS Event Timestamp Enable set to TRUE (checked) GPS LRRP Destination ISSI will be set to the Gateway s Radio ISSI value LRRP Profiles: Powerup Profile GPS Event Location Enable set to TRUE (checked) GPS Event Timestamp Enable set to TRUE (checked) GPS LRRP Destination ISSI will be set to the Gateway s Radio ISSI value CPS 6.2 R 06.20.09.00 Radio MTM5400 6
LRRP Profiles: Powerdown Profile GPS Event Location Enable set to TRUE (checked) GPS Event Timestamp Enable set to TRUE (checked) GPS LRRP Destination ISSI will be set to the Gateway s Radio ISSI value LRRP Profiles: Emergency Entry Profile GPS Event Location Enable set to TRUE (checked) GPS Event Timestamp Enable set to TRUE (checked) GPS LRRP Destination ISSI will be set to the Gateway s Radio ISSI value CPS 6.2 R 06.20.09.00 Radio MTM5400 7
Tetra Gateway application Check that the station is connected using a data cable (GMKN1022A for MTM800 or newer for MTM5400) and not a programming cable! To start the Tetra Gateway application, you will double click the TetraGW shortcut. In the opened window, you will select click Connect, after you have selected the serial communication port under Port name dropdown list. Status indicates the current gateway satsys Last update time of last radio data received Autoconnect option is available, will apply to next restart of gateway application. Tetra Gateway console when first started, status disconnected. It shows the available ports (the serial ports in PC). CPS 6.2 R 06.20.09.00 Radio MTM5400 8
After connecting the radio station, the gateway console will display messages about the state of gateway connection, gps, sms and others. Send keep Alive Request console message The gateway checks the radio connection status and will try to reconnect if the radios is powered off or restarted (expected delay time at reconnection is 10 30 seconds). CPS 6.2 R 06.20.09.00 Radio MTM5400 9
Gateway Status label will indicate current gateway activity: Serial port closed awaiting user to select serial port and click Connect Serial port opened connection with serial port established, looking for attached radio Communication with radio established ready to receive data from radio network Failed to communicate with radio failed to bind to radio, will retrying every 30 sec. Last Update timestamp label is updated for every LRRP Trigger received (gps, sms, ars) CPS 6.2 R 06.20.09.00 Radio MTM5400 10