C CONTENTS CONTENTS PAGE 1 HAMMERSCREWS Haerscrews White Zinc Plated 2 Haerscrews Stainless A2-304 2 2 NYLON FRAME ANCHOR Nylon Frame s Yellow Zinc Plated 3 Nylon Plug 3 3 WINDOW FRAME ANCHOR Window Frame 4 4 METAL HAMMER IN Haer In All 5 Haer In Zamac 5 5 PLASTERBOARD ANCHORS Plasterboard Metal 6 Plasterboard Nylon 6 6 RUBBER NUT (EPDM) Rubber Nut (EPDM) 7 7 HOLLOW WALL ANCHOR Hollow Wall s TOGGLE ANCHORS Toggle 9 Toggle Nylon 9 C Fasteners Limited Construction Fastening Systems - World of Fixings
FIXING SELECTION GUIDE S SELECTOR Key Base Material Suitability Type Full Suitability Limited Suitability No-fines Dense Block Brickwork (Solid) Brickwork (Perforated) Stone Rock Light Aggregate Block (Solid) Light Aggregate Block (Hollow) Aerated Block Hollow Clay Pots Plasterboard Torque Controlled Haerset Page Type 1 2 Haerscrews 2 3 Nylon Frame 3 4 Window Frame 4 5 Metal Haer-in 5 6 Plasterboard s 6 7 Rubber Nut (EPDM) 7 Hollow Wall s 9 Toggle s Telephone: 0114 242 3333 Fax: 0114 242 3300 Email: sales@trutekfasteners.co.uk Website: www.trutekfasteners.com 1
1 The Trutek Haerscrew is one of the fastest and inexpensive methods of fixing for static loads that requires very little screwdriver work. The nylon sleeve is manufactured from durable polymide 6 which gives longer fixing life. This fixing can be used in concrete, solid bricks, lightweight concrete blocks, hollow blocks, rock and stonework. Conduit, drywall track Battens, brackets Skirting boards, signs Bricks ties, frame cramps Switch boxes, trunking Pre-assembled Zinc plated Stainless steel for full corrosion protection Nylon sleeve gives long life Countersunk head allows flush finish One operation through fixing Quick installation Haerscrew White Zinc Plated Plug Min Min Embedment Centre Spacing Edge Distance In 30N/ 2 Tension/Shear Zinc Plated 30 6-7 5 30 20 40 20 0.15 / 0.20 THS05030 5 40 6-7 10 30 20 40 20 0.20 / 0.20 THS05040 50 6-7 25 40 30 40 20 0.20 / 0.20 THS05050 35 7-5 40 30 50 25 0.25 / 0.2 THS06035 40 7-10 40 30 50 25 0.25 / 0.2 THS06040 6 50 7-25 40 30 50 25 0.25 / 0.2 THS06050 60 7-35 40 30 50 25 0.25 / 0.2 THS06060 70 7-45 40 30 50 25 0.25 / 0.2 THS06070 0 7-55 40 30 50 25 0.25 / 0.2 THS0600 60 9-10 25 50 40 60 30 0.40 / 0.40 THS0060 0 9-10 40 50 40 60 30 0.40 / 0.40 THS000 100 9-10 60 50 40 60 30 0.40 / 0.40 THS0100 120 9-10 0 50 40 60 30 0.40 / 0.40 THS0120 140 9-10 95 50 40 60 30 0.40 / 0.40 THS0140 Tensile and shear loads for all above are for 30 N/2 concrete at minimum embedment Haerscrew Stainless A2-304 5 6 Plug Min Min Embedment Centre Spacing Edge Distance In 30N/ 2 Tension/Shear Stainless A2 304 30 6-7 5 30 20 40 20 0.15 / 0.20 THS05030SS 40 6-7 10 30 20 40 40 0.20 / 0.20 THS05040SS 40 7-10 40 30 50 25 0.25 / 0.2 THS06040SS 60 7-35 40 30 50 25 0.25 / 0.2 THS06060SS 0 9-10 40 50 40 60 30 0.40 / 0.40 THS000SS 100 9-10 60 50 40 60 30 0.40 / 0.40 THS0100SS 1. Drill hole to correct diameter and recoended depth. 2. Remove debris and clean hole thoroughly. 3. Push haerscrew through fixture into base material until collar is flush with surface. 4. The anchor will expand by haering the screw until it is flush with the plug head. 2 Fasteners Limited Construction Fastening Systems - World of Fixings
2 The Trutek Nylon Frame is for fixing timber or metal door frames to concrete, stone, brick or blockwork. It has the benefit of being a through fixing which allows the material to be fixed in the correct place prior to being secured. The nylon sleeve is manufactured from durable polymide 6 which gives a longer fixing life. The pozi head screw provided is suitible for use with screw caps. Door & window frames Wall plates Battens Sole plates Through fixing Zinc plated High grade screw gives greater shear performance Nylon sleeve gives long life Through fixing Countersunk head allows flush finish Anti rotation lugs to prevent spinning No marking out is required Nylon Frame Yellow Zinc Plated 10 Plug Min Min Embedment Centre Spacing Edge Distance In 30N/ 2 Tension/Shear Zinc Plated 60 9-10 15 50 40 60 30 1.0 / 2.2 TNFA0060 0 9-10 35 50 40 60 30 1.0 / 2.2 TNFA000 100 9-10 55 50 40 60 30 1.0 / 2.2 TNFA0100 120 9-10 75 50 40 60 30 1.0 / 2.2 TNFA0120 0 11-12 30 55 45 70 35 1.3 / 3.0 TNFA1000 100 11-12 50 55 45 70 35 1.3 / 3.0 TNFA10100 120 11-12 65 55 45 70 35 1.3 / 3.0 TNFA10120 140 11-12 5 55 45 70 35 1.3 / 3.0 TNFA10140 160 11-12 110 55 45 70 35 1.3 / 3.0 TNFA10160 Tensile and shear loads for all above are for 30 N/2 concrete at minimum embedment Nylon Plug Plug Wood Wood Gauge Min Rec Tensile KN Product Code The Trutek Nylon Plug is made from Polymide 6. This increases the life of the product for long term reliability.this plug can be used with both brass and Stainless woodscrews where a corrosion fix is required. 5 25 2.5-4.0 4-30 0.47 TNP05 6 30 3.5-5.0 6-10 35 0.77 TNP06 7 40 4.0-5.5-12 40 0.97 TNP07 40 5.0-6.0 10-14 45 1.12 TNP0 10 50 6.0-.0 14-1 55 2.20 TNP10 12 60.0-10.0 1-24 70 2.95 TNP12 14 75 10.0-12.0 24-32 5 4.7 TNP14 1. Place frame in position and drill appropriate diameter hole through frame and into base material. 2. Remove debris and clean hole thoroughly. 3. Insert plug through into hole and lightly tap until flush with the surface. 4. Insert the screw and tighten until secure. Telephone: 0114 242 3333 Fax: 0114 242 3300 Email: sales@trutekfasteners.co.uk Website: www.trutekfasteners.com 3
3 The Trutek Window Frame is specially designed for fixing of upvc and aluminium frames. The retaining lugs at the top of the sleeve allow the frame to be located in the desired position without distortion. This fixing can be used to fix into concrete, stone, solid brickwork, perforated brickwork, rock and concrete block. upvc door & window frames Aluminium frames Anti rotation fins Zinc plated screw for corrosion resistance Retaining collar Captive expander cone Comes complete with cover caps Through fixing Countersunk head allows flush finish Anti rotation lugs to prevent spinning Window Frame Yellow Zinc Plated (c/w cover cap) Plug Min Min Embedment Centre Spacing Edge Distance In 30N/ 2 Tension/Shear Zinc Plated 100 9-10 60 50 40 60 30 0. / 1.0 TWFA0100 120 9-10 0 50 40 60 30 0. / 1.0 TWFA0120 140 9-10 100 50 40 60 30 0. / 1.0 TWFA0140 75 11-12 25 60 50 70 35 1.3 / 1.5 TWFA10075 100 11-12 50 60 50 70 35 1.3 / 1.5 TWFA10100 10 120 11-12 70 60 50 70 35 1.3 / 1.5 TWFA10120 140 11-12 90 60 50 70 35 1.3 / 1.5 TWFA10140 165 11-12 115 60 50 70 35 1.3 / 1.5 TWFA10165 Tensile and shear loads for all above are for 30 N/2 concrete at minimum embedment Countersunk Head Retaining Collar Frame Retaining Lugs Anti Rotation Fins Captive Expander Cone Zinc Plated 1. Drill hole to correct diameter and recoended depth. 2. Remove debris and clean hole thoroughly. 3. Tap anchor home until sleeve is flush with the frame. 4. Tighten with a pozidrive No. 2 screwdriver.then clip on cover cap. 4 Fasteners Limited Construction Fastening Systems - World of Fixings
4 The Trutek All Haer-In is a nail expanding anchor suitable for materials such as concrete, solid brickwork and solid stonework. It is a vandal proof anchor ideal for fixing signs and notices. This all steel version gives it a high fire resistance. It performs better than the nylon haerscrew in the fixing of plasterboard ceiling panels to a concrete soffit where a better load and fire resistance is beneficial. Signs, bill boards Switch boxes Trunking Brick ties All metal anchor for higher fire resistance Hardened steel expander nail Large diameter head Pre-assembled for quick installation Through fixing Vandal proof for security applications Metal Haer-in All White Zinc Plated 6 Min Flange Head In 30N/ 2 Tension In 30N/ 2 Shear Zinc Plated 35 6-7 13 22 13 1.0 1.4 TSH06035 50 6-7 2 22 13 1.0 1.4 TSH06050 The Trutek All Haer-In is a nail expanding anchor suitable for materials such as concrete, solid brickwork and solid stonework. It is a vandal proof anchor ideal for fixing signs and notices with a large diameter head that gives greater pull over strength. It has a zinc alloy body for corrosion protection. Signs, bill boards Switch boxes Trunking Brick ties Zinc alloy body for corrosion protection Hardened steel expander nail Pre-assembled for quick installation Through fixing Vandal proof for security applications Metal Haer-in Zamac White Zinc Plated Min Flange Head In 30N/ 2 Tension In 30N/ 2 Shear Zinc Plated 30 6-7 22 13 1.1 1.4 TZH06030 6 40 6-7 1 22 13 1.1 1.4 TSH06040 50 6-7 2 22 13 1.1 1.4 TSH06050 1. Drill hole to correct diameter and recoended depth. 2. Remove debris and clean hole thoroughly. 3. Insert haer-in anchor until it is flush with the fixture. 4. Drive the expander nail fully home using a haer. Telephone: 0114 242 3333 Fax: 0114 242 3300 Email: sales@trutekfasteners.co.uk Website: www.trutekfasteners.com 5
5 The Trutek TMPA anchor is a fast and cost effective fixing for lightweight items into plasterboard. It can be used in single or double thickness plasterboard. Rapid and easy installation can be achieved by use of a power or standard pozi drive screwdriver. Electrical boxes Sanitary ware Cable trunking Shelving Self drilling Flange prevents push through Supplied c/w screw Fast and easy installation No min/max plasterboard thickness Cost effective fixing Metal Plasterboard Thread Rec Tensile KN Rec Shear KN Zinc Alloy 4 25 35 15 37 0.06 0.1 TMPA Product supplied c/w screws The Trutek TNPA anchor is a fast and cost effective fixing for lightweight items into plasterboard. It can be used in single or double thickness plasterboard. Rapid and easy installation can be achieved by use of a power or standard pozi drive screwdriver. Electrical boxes Sanitary ware Cable trunking Shelving Nylon Plasterboard Self drilling Flange prevents push through Supplied c/w screw Fast and easy installation No min/max plasterboard thickness Cost effective fixing Nylon construction reduces risk when fixing near electrical cables Thread Rec Tensile KN Rec Shear KN Nylon 4 25 35 15 37 0.06 0.1 TNPA Product supplied c/w screws 1. Position the fixture and mark out holes. Using a pozi drive screwdriver bit, push the fixing firmly into the plasterboard until thread engages. 2. Maintaining firm pressure, screw the fixing into the plasterboard until flush. 3. Place fixture in position, insert screw and tighten until secure. 6 Fasteners Limited Construction Fastening Systems - World of Fixings
6 The Trutek EPDM Rubber Nut is a versatile fixing for problem base materials, cavity fixings and dynamic loads. It can be used for fixing into perforated bricks, hollow concrete block, plastic, sheet metal, plywood and is especially effective in brittle materials. It fits tightly into irregular holes forming a watertight seal. Heating & ventilation systems Blind fixing Hollow concrete flooring Car panelling Brass nut resists corrosion Provides watertight seal Prevents leakage at joints Suitable where access is limited Expands into irregular holes Resists hot oils up to 110ºc Rubber Nut (EPDM) Thread Dia. Wall Min. Wall. Overall Flange Flange Rec Tightening Torque Nm Product Code 3 6 14 24 1.0 11.0 1.0 TRN03240 4 2 13 1.0 11.0 1.0 TRN04100 6 14 24 1.0 11.0 1.0 TRN04240 10 2 14 1.3 13.0 1. TRN05150 5 10 6 14 25 1.3 14.0 1. TRN05250 10 19 26 40 1.3 14.0 1. TRN05400 13 2 15 1.3 16.0 4.0 TRN06150 6 13 3 13 25 1.3 16.0 4.0 TRN06250 13 13 23 35 1.3 16.0 4.0 TRN06350 16 6 15 25 5.7 22.0.0 TRN0250 16 25 35 50 1.6 20.0.0 TRN0500 10 20 25 35 55 1.3 22.5 10.0 TRN10550 12 24 33 45 75 1.3 27.0 15.0 TRN12750 Trutek Recoended Tensile s 3 10 Plasterboard 10 Plywood 7N Hollow Blocks Product Code TRN03240 0.2 TRN04100 TRN04240 0.2 TRN05150 0.1 0.2 TRN05250 0.2 0.3 TRN05400 0.2 TRN06150 0.1 0.4 TRN06250 TRN06350 0.2 0.4 0.4 TRN0250 1.0 1.0 TRN0500 2.3 2.2 TRN10550 2.4 TRN12750 s may vary subject to the condition of the base material 1. For hollow applications drill a hole the same diameter as the rubber nut through the cavity. For solid materials, drill to a min. depth equal to the length of rubber nut. 2. Remove debris and clean hole thoroughly. 3. Insert the rubber nut upto the flange.then put the fixture in place. 4. Insert bolt and tighten. The rubber nut works as well in regular holes by expanding firmly against the sides of the hole. Telephone: 0114 242 3333 Fax: 0114 242 3300 Email: sales@trutekfasteners.co.uk Website: www.trutekfasteners.com 7
7 The Trutek Hollow Wall is a preassembled cavity fastener. It can be used to fix into plasterboard, clay pot ceilings, sheet steel. Small Sizes can be used to fix into hardboard and plywood.the screw in this fixing can be removed and re-fitted making it ideal for removal of fixtures for redecorating. The Trutek Setting Tool is available which allows for fast, repetitive fixing. Electrical fittings Shelving Pipe saddles Radiators Brackets Hollow Wall Zinc and yellow passivated Combination head screw Anti rotation lugs Large flange prevents pull into base Fast installation with setting tool The screw can be removed and re-fitted Flush finish head Plug Size Wall Rec Tensile Kn Rec Sheer Kn 20 M4 X 25 0-5 THW04025 3 M4 X 45 16-16 0.10 0.14 THW04045 46 M4 X 50 17 16-23 0.10 0.14 THW04050 60 M4 X 65 20 1-32 0.10 0.23 THW04065 3 M5 X 45 17 6-13 0.1 0.23 THW05045 10 52 M5 X 60 26-16 0.1 0.23 THW05060 65 M5 X 70 26 16-32 0.1 0.23 THW05070 13 52 M6 X 60 30 7-16 0.29 0.34 THW06060 65 M6 X 70 26 16-32 0.29 0.34 THW06070 Rec. loads are based on 12 plasterboard Hand Setting Tool THWT01 1. Drill hole the recoended size. 2. Insert the fixing into the hole.tap fixing lightly ensuring that the anti-rotation lugs penatrate the base material. 3. Attach setting tool to screw and position the anchor. Smaller sizes may be set with a screwdriver. 4. Remove the screw and position the fixture. Insert screw through fixture and base material and tighten until secure. Fasteners Limited Construction Fastening Systems - World of Fixings
The Trutek Spring Toggle is an all metal wing cavity fastener. It is ideal for ceiling installations due to its fire resistant properties. It offers high loadings in plasterboard as the wings spread the load over a wide area. Overhead lighting Curtain tracks Pictures High fire resistance Zinc and yellow passivated Machine screw for ease of tightening Spreads load over wide area Heavy gauge material for increased loads Heavy gauge nut prevents stripping Spring Toggle Wing & and Wing Only Thread Cavity Rec Tensile Kn Product Code 11 3 X 50 3 30 20 0.10 TST03050 4 X 50 4 20 30 0.14 TST04050 14 5 X 50 5 20 30 0.1 TST05050 5 X 75 5 45 30 0.1 TST05075 5 X 100 5 70 30 0.1 TST05100 1 6 75 X 6 45 30 0.30 TST06075 11 3 20 0.10 TST03 14 4 30 0.14 TST04 5 30 0.1 TST05 1 6 30 0.30 TST06 22 40 0.60 TST0 25 10 40 0.0 TST10 1. Drill hole the recoended size. 2. Compress the wings and push the fixing into the hole. 3. Tighten the screw until the fixture is secure. Nylon Toggle The Trutek Nylon Toggle is a one piece cavity fastener. It is a medium duty anchor for use in plasterboard. s can be removed and refitted to allow for redecoration and can be used with both woodscrews or self-tapping screws. Main applications are ceiling fixtures, light shelving, brackets and hooks. Wood Size Wood Guage Wall Min. Cavity Rec Tensile Kn Product Code 3.5-4.0 6-10-13 30 0.12 TTA10 3.5-4.0 6-10-16 35 0.12 TTA12 3.5-4.0 6-10-20 40 0.12 TTA16 1. Drill an hole in base material. 2. Compress the wings and push the fixing into the hole. 3. Tap the fixing flush with the surface. 4. in the fixing making sure the screw length is 25 longer than the combined fixture & plasterboard. Telephone: 0114 242 3333 Fax: 0114 242 3300 Email: sales@trutekfasteners.co.uk Website: www.trutekfasteners.com 9