OWNR S MNUL randview ex azebo with Netting Product code: 71 M12207 UPC code: 769455 761170 Vendor Item: SS-I-138-2NZ ate of purchase: / / 1
Special Warning ssemble your gazebo on a soft, non-abrasive surface to avoid damage. The gazebo is heavy. Use care when handling. ssembly by six adults is recommended. The gazebo is not intended to be a permanent structure. Take it down during high winds or it may be damaged. KP LL LM N T SOURCS WY ROM CNOPY RIC The canopy is made with flame-resistant fabric which meets CPI-84 specifications. It is not fireproof. The canopy fabric will burn if left in continuous contact with flame source. The application of any foreign substance to the canopy fabric may render the flame-resistant properties ineffective. Caution: This gazebo is made for explicit purpose of providing limited outdoor sun shade and is not to be used as a toy, shelter or tent. This gazebo is not intended for inclement weather in any form including, but not limited to: rain, hail, sleet, snow and/or wind. o not locate structure near any open flame. o not use structure as a support. o not shake, lean or climb on structure. Children under age of 10, near the structure, should be supervised by a competent adult at all times. PRTS Read through all the instructions before beginning assembly. Unpack and identify all the parts. Place them on a flat, non-abrasive surface. ssembly by six people is recommended. (6) Leg Post (3) ecorative nel C (1) Tabletop Crossbar (6) Top eam (1) (1) Short Canopy rame Long Canopy rame Center Piece Center Piece (6) Long Canopy rame ar (6) Short Canopy rame ar I (1) (1) Tabletop Tabletop (with I label) (with label) K (2) Tabletop Support ar L (1) Tabletop Support ar 2
M (1) Large Canopy N (1) Wind Vent Canopy O (6) Net CCSSORIS (51 + 3 spares) Short olt Pg (2) llen Wrench Pb (7 + 1 spare) Long olt Ph (2) Open ex Wrench (66 + 3 spares) Metal Washer Pi (1) Touch-up int Pd (8 + 1 spare) Nut Pj (1) ssembly Instructions Sheet Pe (6) racket Pk (1) Plastic Washer Pf (12) Lawn Stake Pl (1) ook 3
SSMLY INSTRUCTIONS 1 ttach a decorative panel () to two leg posts (). Insert two hooks of decorative panel () into two holes of two leg posts (). See ig. 1. Then insert the pins through the decorative panel () and into the leg post () for each hole. See ig. 2. Repeat procedure for the remaining decorative pannels () and leg posts (). ig. 1 NOT: or the decorative panel, the horizontal crossbar with holes should face upside as shown in figure. ig. 2 2 ttach the tabletop crossbar (C) to the assembled frame (&) Line up all holes and for each hole insert a short bolt () through a metal washer (), through the bracket of tabletop crossbar (C) and secure into the leg post () or into the decorative pannel (). See ig. 3 and ig. 4. Tighten all bolts. NOT: The holes of tabletop crossbars (C) should face inside (for attaching to tabletops). ig. 4 C C C ig. 3 3 ttach a top beam () to assembled frame (&). Line up all holes and for each hole insert a short bolt () through a metal washer () through the top beam () and secure into leg post (). on t tighten completely. Repeat procedure for the other side and the remaining top beam (). See ig. 5. NOT: or the decorative panel, the vertical crossbar with holes should face inside as shown in figure. ig. 5 ig. 6 Pe ttach a bracket (Pe) to a leg post () as shown in the fighure. Line up the holes and insert a short bolt () through a metal washer (), through the bracket (Pe) and secure into the post () for each hole. o not tighten completely. Repeat procedure for the remaining brackets (Pe). See ig. 6. Tighten all bolts. 4
4 ttach the long canopy frame bars () to the long canopy frame center piece (). Push down the button and insert a frame bar () into the center piece (), make sure the button fits securely into the hole. Repeat procedure for the remaining long canopy frame bars. See ig. 7. ig. 7 5 Place the large canopy (M) over the assembled canopy frame (&) and spread to the location. See ig. 8. ig. 8 M 6 ttach the short canopy frame bars () to the short canopy frame center piece (). Push down the button and insert a frame bar () into the center piece (), make sure the button fits securely into the hole. Repeat procedure for the remaining short canopy frame bars. See ig. 9. ig. 9 7 Place the wind vent canopy (N) over the assembled canopy frame (&). Insert each end of the frame bars () into the pockets of the wind vent canopy (N). Pull down the canopy fabric and spread. See ig. 10. N N ig. 10 5
8 ttach the assembled short canopy frame (&) to the assembled long canopy frame (&). Push down the button and insert long canopy frame center () into the short canopy frame center piece (), make sure the button fits securely into the hole. See ig. 11. t the same time, insert long canopy frame bars () into short frame bars (). See ig. 12. rom inside of the canopy, fasten Velcro tabs to connect the wind vent canopy (N) with the large canopy (M). ig. 11 N ig. 12 M 9 Place the completed canopy onto the top of assembled leg posts. Line up the holes, insert a long bolt (Pb) through a metal washer (), through the canopy frame bar (), through the bracket (Pe), through another metal washer () and secure with a nut (Pd). on t tighten completely. Repeat procedure for the remaining five canopy frame bars (). Tighten all bolts and nuts. See ig. 13. Pull down the edges of the canopy fabric and insert each tip of the canopy frame bar () into the pocket of the canopy fabric. Pe Pb Pd ig. 13 10 : ttach the tabletop () to the tabletop crossbar (C). Line up the holes, insert a short bolt () through a metal washer (), the tabletop () and secure into the tabletop crossbar (C) for each hole. See ig. 14. on t tighten completely. Insert the bracket of tabletop () into support bar (K) and line up the holes. See ig. 15. Insert a short bolt () through a metal washer (), the support bar (K) and secure into the bracket of tabletop (). See ig. 16. Insert a short bolt () through a metal washer (), through the other end of support bar (K) and secure into decorative panel (). See ig. 17. on t tighten completely. Repeat procedure for tabletop (I). 6
: ttach the support bar (L) to decorative panel (). Line up the holes, insert a short bolt () through a metal washer (), though the bracket of support bar (L) and secure into decorative panel (). See ig. 18. ttach the tabletop () to the tabletop (I). Line up the hole, insert a short bolt () through a metal washer (), the tabletop (I), the tabletop (), another metal washer () and secure with a nut (Pd). ttach the support bar (L) to the tabletop (&I). Insert a long bolt (Pb) through a metal washer (), the tabletop (&I), a plastic washer (Pk), the support bar (L), another metal washer () and secure with a nut (Pd). See ig. 19. Securely tighten all botls and nuts. ig. 14 M C ig. 15 I K L ig. 16 ig. 17 K K ig. 18 L Pd L Pd Pk Pb I ig. 19 11 Secure the gazebo to the ground by inserting the lawn stakes (Pf) through the holes at the bottom of the leg post () into the ground. See ig. 20. Pf Pf ig. 20 7
ig. 23 12 ttach the nets (O) to the top beams () with Velcro tabs. See ig. 21. Make sure the top beam is between the two edges of the canopy fabric (M). asten the canopy and net to the leg posts with the hooks. See ig. 22. ttach the S shaped hook (Pl) to the ring of canopy frame center piece (). The S shaped hook is used for hanging decoration items if necessary. See ig. 23. Pl O ig. 22 M O Your gazebo is now ready for use. njoy! ig. 21 O PLS NOT: 1. To remove canopy support bars press the pushpin in the cylinder that connects the top and bottom canopy supports and lift evenly as shown in the figure. 2. To remove any bars connected by the pushpin, press the pushpin in the bar and pull out the bar evenly as shown in the figure. CR INSTRUCTIONS Wash with a mild solution of soap and water; rinse thoroughly. ry completely. o not use bleach or solvents. Cover furniture with outdoor furniture covers when not in use. Please refer to part numbers when reordering or questions or comments about product: Call toll-free: 800-457-4652 Made in / ech en CIN istributed by Sears, Roebuck and Co., offman states, IL 60179 sears.com See our extensive assortment of outdoor living products on-line at www.sears.com and www.kmart.com 8