CAON: Vaughn Single Pendant Assembly and nstallation nstructions BEFOE NSALLNG FXE, MAKE SE E POWE O E CC S NED OFF A E MAN FSE BOX / CC BEAKE LY BOX. mportant Safety nstructions: hese instructions are provided for your safety. t is very important that they are read carefully and completely before beginning the assembly and installation of this lighting fixture. We strongly recommend that a professional electrician install all direct wire fixtures. S PODC MS BE NSALLED N ACCODANCE W E APPLCABLE NSALLAON CODES BY A PESON FAMLA W E CONSCON AND OPEAON OF E PODC AND E AZADS NVOLVED. he lighting fixture is meant for indoor use. t must be connected only to 3-wire, single-phase electrical supply systems (provided with Ground wire or equivalent protection system). For your safety, it is strongly recommended that two people install the lighting fixture. his fixture has been rated for up to E26 one (1) 60-Watt maximum YPE standard (tubular) incandescent light bulb (not included) or one (1) 13-Watt compact fluorescent light bulb (not included) or one (1) 9-watt SBLED light bulb ( not included).o avoid the risk of fire, do not exceed the recommended lamp wattage. his lighting fixture is intended for indoor or protected/covered outdoor areas. Do not expose to direct rainfall. SABLE FO EE DY O DAMP LOCAONS. Save these instructions. WANNG: o reduce the risk of fire, electrical shock or personal injury, always turn off light fixture and allow it to cool prior to replacing light bulb. Do not touch bulb when fixture is turned on. Do not look directly at lit bulb. Keep flammable materials away from lit bulb. his lighting fixture contains lead, a chemical known to the State of California to cause cancer, birth defects and other reproductive harm. Wash hands after installing, handling, cleaning or otherwise touching this light fixture. Pre-assembly: emove all parts and hardware from box along with any plastic protective packaging. Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware. For your safety and convenience, assembly by two people is recommended. S/CN Page 1 of 7
OOLS EQED (not included): Parts ncluded: (A) Mounting Plate (1) (a) Wrench (1) (B) hreaded ube (1) (b) Socket ing (1) (C) Fixture Loop (1) (c) Washer (1) (D) Canopy (1) (E) Canopy Nut (1) (F) anging Loop (1) (G) 5.75 Connection tubes (2) () 12 Connection tubes (2) () 17.75 Connection tubes (2) (J) Joint (1) (K) Light Fixture (1) (L) ex Nut (1) (M) Socket (1) (Q) Glass Shade (1) () Open Wrench (1) (S) Closable Link (1) () Connectors (6) () Caps (5) (V) 18 hreaded ubes (2) (W) 11.75 hreaded ubes (2) (X) 6 hreaded ubes (2) (Y) Allen Wrench (1) ardware Enclosed: (N) Green Ground Screw (1) (O) Mounting Screws (2) (P) Plastic Wire Nut Connectors (3) K O J Mount i ng Scr ews 3X V M P Pl ast i c Wi r e Nut Connect or s 3X W N P C O Gr een Gr ound Scr ew 1x Junction box S F E S/CN Page 2 of 7 G X c b a Q D Y L A N B
o adjust the suspension length of the fixture: 1. Note: he adjustment or shortening of the lighting fixture s suspension length is only needed if the factory set length is not appropriate for your installation. We recommend that you adjust the Connection od quantity to the proper desired length before cutting the electrical cord. Determine the lighting fixture suspension length from the ceiling for the product installation, allowing the extra cord length for the outlet junction box wire connections as noted below. 2. (See A1,A2,A3 &A4)) hread the fixture 2 wire cord, bare copper wire through the Connector (), 18 hreaded ube (V). hread the Connector () into the Joint (J) by rotating clockwise until tight. And thread the 18 hreaded ube (V) into the Connector () by rotating clockwise until tight. Slide 17.75 Connection tubes () and Caps () along the hreaded tubes (V). se the Additional ubes (G//) as needed, to adjust the fixture s suspension length by following the procedures as shown in illustration A2, A3 &A4.. W G F Y X J V V W G X 3. (See A5) f needed, cut off the extra power cord length on the 2 wire cord and bare ground wire so that they all are at least 6 inches (152.4 mm) long within the outlet junction box (J-box). S/CN Page 3 of 7
Assembly & nstallation nstructions: S OFF E MAN ELECCAL SPPLY FOM E MAN FSE BOX/CC BEAKE. Carefully unpack all fixture parts and hardware and lay them on a clear workspace. C D E 1. Separate Mounting Loop (C) from Canopy (D) by removing Canopy Nut (E) in counter-clockwise direction. Do not discard as well these will be used later. 2. Attach the hreaded ube (B) into the threaded bore of the anging Loop (C) and rotate the hreaded ube (B) clockwise until it is tightly engaged within the anging Loop (C). Attach the Mounting Plate (A) onto the top end of the hreaded ube (B) so that a portion of the hreaded ube (B) extends beyond the Mounting Plate (A) 3. Position the ex Nut (L) onto the top end of hreaded ube (B). ighten the ex Nut (L) until tight using pliers so that the anging Loop (C) is now firmly secured to the middle of the Mounting Plate (A). S/CN Page 4 of 7
4. Weave the fixtures power cord and bare ground wire through every other loop to the top of Chain, and then through the anging Loop and hreaded ube. P 5. Please read the section o Make the Wire Connections Below. 1/2 inch exposed wi r es 6. Attach the Mounting Plate (A) onto the junction box using Mounting Screws (O) S/CN Page 5 of 7
B7 7. Slide Canopy Nut (E) and Canopy (D) to the tube. ook anging Loop (F) to Closable Link (S) B8 8. Slide the Canopy (D) upward along the tube with the upper rim of the canopy pressed gently against the ceiling surface. Position the Canopy Nut (E) against the anging Loop (C) and rotate the nut clockwise to engage it with the threaded portion of the anging Loop (C) until secure. Do not over tighten this nut. B9 K M Q c b 9. nsert Glass Shade (Q) into Light Fixture (K) and secure with washer (c) and socket ring (b). ighten with wrench (a). a M B10 10. nsert the specified light bulb into the Socket (M). DO NO EXCEED E SPECFED WAAGE. S/CN Page 6 of 7
o Make the Wire Connections: 1. Gently pull existing wire down from the ceiling junction box and allow wires to hang. he O or LVE wire is usually black. he NEAL wire is usually white. Check to see if there is a ground wire that is usually green or green with a yellow stripe or exposed copper metal wire. f needed, use a pair of wire strippers to remove about 1/2 inch of insulation from each wire. 2. Carefully inspect the fixtures wires. he NEAL FXE WE has FNE LONGDNAL DGES running along its length. he O FXE WE is SMOO and the BAE COPPE WE is the GOND WE. f you have any doubt and cannot identify the power-supply wires with confidence, then we recommend that you ask an electrician and that you not continue with the installation. 3. With the help of another person to hold the weight of the fixture, attach the fixture wires to the junction box wires as shown in the illustrations. Connect the GOND FXE WE to the GOND J-BOX WE using the Plastic Wire Nut Connector (P) and wrap the connection with electrical tape. Be sure that no wire strands are exposed. A N f the junction box DOES NO have a GOND WE, wrap the fixture's bare ground wire around the Green Ground Screw (N) and insert the screw into the Mounting Plate (A), marked as GND, and tighten screw to secure the wire. Connect the NEAL FXE WE to the NEAL J-BOX WE first and then connect the O FXE WE to the O J-BOX WE using the Plastic Wire Nut Connectors (P). Wrap these connections with electrical tape. Be sure that no wire strands are exposed. NOE: S MPEAVE A E JNCON BOX N YO OME BE POPELY GONDED!S DO NO EVESE E O AND NEAL CONNECONS O SAFEY WLL BE COMPOMSED. 4. Check the wiring connections and if all looks good, gently tuck the wire connections neatly into the ceiling junction box. Care instructions: Wipe clean with a soft, dry cloth or static duster. Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the fixture s finish. hank you for your purchase Stores catalog www.williams-sonoma.com SA 1.877.812.6235 S/CN Page 7 of 7