Fifth Wheel Hitch INSTALLATION MANUAL

Fifth Wheel Hitch INSTALLATION MANUAL VICTORIA INDUSTRIES LTD. 4224 Commerce Circle Victoria, B.C. CANADA V8Z 6N6 Tel: (250) 386-6231 Fax: (250) 383-6533 Web Site: http//www.hijacker.com Revision Date: 03/15/11 IMPORTANT NOTICE: This manual and all advice issuing from the office of Victoria Industries Ltd. are given conscientiously and in good faith. However, the purchaser has full control of, and must accept responsibility for, the use and application of our products in their possession. While our products carry a manufacturer s warranty against defects, Victoria Industries Ltd. will not accept liability for damages resulting from the misuse or misapplication of our products. These installation instructions are for installation of Hijacker hitches in trucks with a 6 ½ box (minimum) or 8 box. Victoria Industries does not have any recommended installations for trucks with less than a 6 ½ box. This includes trucks with a 5 ½ box.

HIJACKER FIFTH WHEEL HITCH INSTALLATION MANUAL SECTION 1: GENERAL INFORMATION 1 Fifth Wheel Hitch Warranty 2 Fifth Wheel Hitches Model Code 3 General Installation And Safety (*) Instructions 4 Hitch / Truck Combinations: Installation Brackets Required 5 Optional Frame Brackets 6 Hitch Heights 7 Trouble Shooting Instructions 8-9 Hijacker Double Pivot Head Assembly 10 SECTION 2: UL HITCHES (all Ultra cross bed mounted base rail models) 11 UL Hitch 3D Schematic Drawings and Part Numbers 12-18 UL Hitch Rail Dimensions 19 UL Base Rail Shim Install 20 UL Frame Bracket Kits: F150BK04 21 F350ULBK 22 D1535BK 23 D1535ND 24 D3500BK2 25 T07ULBK 26 N04F 27 UL05DAK 28 FB001001 29 FB002001 30 FB002002 31 INSTALLATIONS: FORD: 1973-88 F Series 2.100 FORD: 1989-96 F150 / F-250 (6 ½ & 8 Box) 2.101 FORD: 1992-98 F350 (8 Box) 2.102 FORD: 1997-98 F250 Heavy Duty (6 ½ & 8 Box) 2.102 FORD: 1997 F250 Light Duty (6 ½ & 8 Box) 2.103 FORD: 1997-2003 F-150 (6 ½ & 8 Box) 2.104 FORD: 1998 F-250 Light Duty (6 ½ & 8 Box) 2.104 FORD: 1999-2004 F250 / F350 Super Duty (6 ½ & 8 Box) 2.105 FORD: 1999-2000 F250 Light Duty (6 1/2" & 8 Box) 2.106 FORD: 2000-07 F-450 / F-550 Super Duty 2.107 FORD: 2004-2010 F150 (6 ½ & 8 Boxes Only) 2.108 FORD: 2005-2010 F250 / F350 Super Duty (6 ½ & 8 Box) 2.109 FORD: 2008-2010 F450 Super Duty (6 ½ & 8 Box) 2.109 FORD: 2011 F250 / F350 Super Duty (6 ½ & 8 Box) 2.110 FORD: 2011 F450 Super Duty (6 ½ & 8 Box) 2.110 CHEV / GMC: 1981-87 Pickups 2.200 CHEV / GMC: 1988-97 1500 / 2500 (6 ½ Box) 2.201 CHEV / GMC: 1988-98 1500/2500/3500 (8 Box) 2.202 CHEV / GMC: 1998-2000 3500 (8 Box) 2.202 CHEV / GMC: 1998-99 1500/2500 (6 ½ Box) 2.203 CHEV / GMC: 1998-2000 3500 (6 ½ Box) 2.203 CHEV / GMC: 1999-2006 Silverado & Sierra 1500/2500 (6 ½ Box) 2.204 CHEV / GMC: 2001-04 1500 HD (6 ½ Box) 2.204 CHEV / GMC: 1999-2006 Silverado & Sierra 1500/2500 (8 Box) 2.205 CHEV / GMC: 2003-06 Silverado & Sierra 1500 & 1500 HD (6 ½ Box) 2.206

CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD (8 Box) 2.207 CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD (6 ½ Box) 2.208 CHEV / GMC: 2001-07 Silverado & Sierra 3500 HD (8 Box) (includes Quad Cab) 2.209 CHEV / GMC: 2007-2011 Silverado & Sierra 1500 HD (6 ½ Box) 2.210 CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD (6 ½ Box) 2.211 CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD (8 Box) 2.212 CHEV / GMC: 2007-2010 Silverado & Sierra 3500 HD (8 Box) 2.213 CHEV / GMC: 2011 Silverado & Sierra 2500 & 3500 HD (6 ½ Box) 2.214 CHEV / GMC: 2011 Silverado & Sierra 2500 & 3500 HD (8 Box) 2.215 DODGE: 1993 & Earlier Ram 2.300 DODGE: 1994-2001 RAM 1500 (6 ½ Box) 2.301 DODGE: 1994-2002 RAM 2500 / 3500 (6 ½ Box) 2.301 DODGE: 1994-97 RAM 1500 / 2500 / 3500 (8 Box) 2.302 DODGE: 1998-2001 RAM 1500 (8 Box) 2.303 DODGE: 1998-2002 Ram 2500/3500 (8 Box) 2.303 DODGE: 2002-08 Ram 1500 (4x2 & 4x4) (6 ½ & 8 Box) (includes MegaCab) 2.304 DODGE: 2003-2011 Ram 2500 (4x2& 4x4) (6 ½ & 8 Box) (includes MegaCab) 2.304 DODGE: 2003-2011 Ram 3500 (4x4 models only) (6 ½ & 8 Box) (includes MegaCab) 2.304 DODGE: 2003-2011 Ram 3500 (4x2 models only) (6 ½ & 8 Box) (includes MegaCab) 2.305 DODGE: 2002 & Earlier Dakota 2.306 DODGE: 2003-04 Dakota (6 ½ Box) (Does not include Quad Cabs) 2.307 DODGE: 2005 Dakota (6 ½ Box) (Does not include Quad Cabs) 2.308 TOYOTA: 2000 & earlier T100 Regular & Extended Cab (includes 4x4) 2.400 TOYOTA: 2000-2006 Tundra Regular & Extended Cab (6 ½ & 8 Box) 2.401 TOYOTA: 2007-2011 Tundra Regular & Extended Cab (6 ½ & 8 Box) 2.402 NISSAN: 2004-07 Titan (6 ½ & 8 Box) 2.500 NISSAN: 2008 Titan (8' Box only) 2.501 SECTION 3: SL HITCHES (all Slider parallel mounted base rail models) 32 SL Hitch 3D Schematic Drawings and Part Numbers 33-37 SL Hitch Rail Dimensions 38-39 SL Frame Bracket Kits: F150SLBK 40 INSTALLATIONS: F350SLBK 41 D24SLBK 42 D34SLBK 43 SL05DAK 44 FB101001 45 FB102001 46 FB103001 47 FORD: 1973-88 F Series 3.100 FORD: 1989-96 F150 / F-250 (6 ½ & 8 Box) 3.101 FORD: 1992-98 F350 (8 box) 3.102 FORD: 1997-98 F250 Heavy Duty (6 ½ & 8 Box) 3.102 FORD: 1997 F250 Light Duty (6 ½ & 8 Box) 3.103 FORD: 1997-2003 F-150 (6 ½ & 8 Box) 3.104 FORD: 1998 F-250 Light Duty (6 ½ & 8 Box) 3.104 FORD: 1998 & Earlier Ranger 3.105 FORD: 1999 Ranger 3.106 FORD: 1999-2000 F250 Light Duty (6 ½ & 8 Box) 3.107 FORD: 1999-2004 F250 / F350 Super Duty (6 ½ & 8 Box) 3.108 FORD: 2004-2011 F150 (6 1/2 & 8 Boxes Only) 3.109 FORD: 2005-2010 F250 / F350 Super Duty (6 ½ & 8 Box) 3.110

FORD: 2008-2010 F450 Super Duty (6 ½ & 8 Box) 3.110 FORD: 2011 F250 / F350 Super Duty (6 ½ & 8 Box) 3.111 FORD: 2011 F450 Super Duty (6 ½ & 8 Box) 3.111 CHEV / GMC: 1981-87 3.200 CHEV / GMC: 1988-97 1500 / 2500 (6 ½ Box) 3.201 CHEV / GMC: 1988-98 1500/2500/3500 (8 Box) 3.202 CHEV / GMC: 1998-2000 3500 (8 Box) 3.202 CHEV / GMC: 1997 & Earlier S-10 3.203 CHEV / GMC: 1998-99 1500/2500 (6 ½ Box) 3.204 CHEV / GMC: 1998-2000 3500 (6 ½ Box) 3.204 CHEV / GMC: 1999-2006 Silverado & Sierra 1500/2500 (6 ½ Box) 3.205 CHEV / GMC: 2001-04 1500 HD (6 ½ Box) 3.205 CHEV / GMC: 1999-2006 Silverado & Sierra 1500/2500 (8 Box) 3.206 CHEV / GMC: 2003-06 Silverado & Sierra 1500 & 1500 HD (6 ½ Box) 3.207 CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD (6 ½ Box) 3.208 CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD (8 Box) 3.209 CHEV / GMC: 2001-07 Silverado & Sierra 3500 HD (8 Box) (includes Quad Cab) 3.210 CHEV / GMC: 2007-2011 Silverado & Sierra 1500 HD (6 ½ Box) (24 SL Install) 3.211 CHEV / GMC: 2007-2011 Silverado & Sierra 1500 HD (6 ½ Box) (34 SL Install) 3.212 CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD (6 ½ Box) 3.213 CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD (8 Box) 3.214 CHEV / GMC: 2007-2010 Silverado & Sierra 3500 HD (8 Box) 3.215 CHEV / GMC: 2011 Silverado & Sierra 2500 & 3500 HD (6 ½ Box) 3.216 CHEV / GMC: 2011 Silverado & Sierra 2500 & 3500 HD (8 Box) 3.216 DODGE: 1993 & Earlier Ram 3.300 DODGE: 1994-2001 RAM 1500 (6 ½ Box) 3.301 DODGE: 1994-2002 RAM 2500 / 3500 (6 ½ Box) 3.301 DODGE: 1994-97 RAM 1500 / 2500 / 3500 (8 Box) 3.302 DODGE: 1998-2001 RAM 1500 (8 Box) 3.303 DODGE: 1998-2002 Ram 2500/3500 (8 Box) 3.303 DODGE: 2002-08 Ram 1500 (4x2 & 4x4) (6 ½ & 8 Box) (includes MegaCab) (24 SL Install) 3.304 DODGE: 2003-2011 Ram 2500 (4x2& 4x4) (6 ½ & 8 Box) (includes MegaCab) (24 SL Install) 3.304 DODGE: 2003-2011 Ram 3500 (4x4 models only) (6 ½ & 8 Box) (includes MegaCab) (24 SL Install) 3.304 DODGE: 2003-2011 Ram 3500 (4x2 models only) (6 ½ & 8 Box) (includes MegaCab) (24 SL Install) 3.304 DODGE: 2002-08 Ram 1500 (4x2 & 4x4) (6 ½ & 8 Box) (includes MegaCab) (34 SL Install) 3.305 DODGE: 2003-2011 Ram 2500 (4x2& 4x4) (6 ½ & 8 Box) (includes MegaCab) (34 SL Install) 3.305 DODGE: 2003-2011 Ram 3500 (4x4 models only) (6 ½ & 8 Box) (includes MegaCab) (34 SL Install) 3.305 DODGE: 2003-2011 Ram 3500 (4x2 models only) (6 ½ & 8 Box) (includes MegaCab) (34 SL Install) 3.305 DODGE: 2002 & Earlier Dakota 3.306 DODGE: 2003-04 Dakota (6 ½ Box) (Does not include Quad Cabs) (24 SL Model Only) 3.307 DODGE: 2005 Dakota (6 ½ Box) (Does not include Quad Cabs) (24 SL Model Only) 3.308 DODGE: 2009-2011 Ram 1500 (4x2 & 4x4) (6 ½ Box) (includes MegaCab) (24 SL Install) 3.309 TOYOTA: 1998-2001 Tacoma Regular & Extended Cab (includes 4x4) (24 SL Install Only) 3.400 TOYOTA: 2000 & earlier T100 Regular & Extended Cab (includes 4x4) 3.401 TOYOTA: 2000-2006 Tundra Regular & Extended Cab (6 ½ & 8 Box) (34 SL Install Only) 3.402 SECTION 4: UMS HITCHES (all under box mounted base rail models) 48 UMS Hitch 3D Schematic Drawings and Part Numbers 49-53 FB201001 54 FB202001 55 FB202002 56

UMS Hitch Rail Dimensions 57 INSTALLATIONS: FORD: 1999-2011 F250 / F350 Super Duty (6 ½ & 8 Box) 4.100 FORD: 2008-2011 F450 Super Duty (6 ½ & 8 Box) 4.100 FORD: 2004-2011 F150 (6 ½ & 8 Box) (Regular and Super Cab only) 4.101 CHEV / GMC: 2007-08 Silverado & Sierra 2500 HD (8 Box) 4.200 CHEV / GMC: 2003-07 Silverado & Sierra 1500 & 1500 HD (6 ½ Box) 4.200 CHEV / GMC: 2001-07 Silverado & Sierra 3500 HD (8 Box) 4.200 CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD (6 ½ Box) 4.200 CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD (8 Box) 4.200 CHEV / GMC: 2007-2010 Silverado & Sierra 3500 HD (8 Box) 4.200 CHEV / GMC: 2007-2011 Silverado & Sierra 1500 & 1500 HD (6 ½ Box) (Tube Frame) 4.300 CHEV / GMC: 2011 Silverado & Sierra 2500 & 3500 HD (6 ½ Box) 4.201 CHEV / GMC: 2011 Silverado & Sierra 2500 & 3500 HD (8 Box) 4.202 DODGE: 2002-08 Ram 1500 & 2003-2011 Ram 2500/3500 (6 ½ & 8 Box) 4.300 SECTION 5: AUTOSLIDE HITCH 58 AutoSlide Hitch 3D Schematic Drawings and Part Numbers 59-60 AutoSlide 5 th Airborne Adapter Plate 61 AutoSlide Mor/Ryde Adapter Plate 62 AutoSlide Instructions 63-74 SECTION 6: GOOSENECK HITCH INFORMATION 75 Gooseneck Hitch 3D Schematic Drawings and Part Numbers 76-79 Gooseneck Hitch Dimensions 80-84 SL Gooseneck Hitch Assembly 85-86 SECTION 7: BULLETINS AND UPDATES 87 Bed Liner Installations 88

Section 1 --- General Information 1

2 Fifth Wheel Hitch Warranty If any part or parts manufactured by Victoria Industries Limited, (the manufacturer), should prove to be defective within five years from the date it is delivered new to the original purchaser, return the part prepaid to Victoria Industries Limited, 941 Ellery Street, Victoria, BC, V9A 4R9 and if in its opinion the defect is due to defective materials or workmanship furnished by the manufacturer, the part will be replaced or repaired without charge for the part, labor or freight involved in its replacement. The manufacturer s responsibility is limited to the replacement of defective parts as described above and is in lieu of all conditions or warranties expressed or implied, statutory or otherwise. The purchaser takes the part or parts as is and with faults, without any warranty as to merchantability or fitness for any purpose and the manufacturer shall not be responsible for any loss, damage, injury, expense, or other liability, in tort or in contract arising out of the use, design or condition of any part or parts or arising out of any defective part or parts, occurring to any person or to the property of any persons, whether arising from the negligence of the manufacturer or otherwise. Any defective part or parts must be returned to the manufacturer with all postage or shipping charges prepaid promptly upon discovery of the defect. In no event will this warranty apply to any part or parts that have been modified, re-worked, or altered in anyway without prior consent of Victoria Industries Limited or if the part or parts are received at the manufacturer s place of business after five years from the date of delivery to the original purchaser. If in the opinion of the manufacturer the defect in any part or parts is not the result of defective material or workmanship furnished by the manufacturer the part or parts may be disposed of as scrap twenty days after notice to the purchaser of the manufacturer s decision. For the warranty to be effective, the original bill of sale must be retained as proof of purchase and be made available if required by the manufacturer.

Fifth Wheel Hitches Model Code 3 Hijacker XX - XXX XX UNIT WIDTH STYLE GROSS VEHICLE WEIGHT RATING 24 = 24 Slider (installs ALONG the truck bed ) 16 = 16,000 lbs. 34 = 34 UL - = Ultra (installs ACROSS the truck bed) 21 = 21,000 lbs. - - P = Double Pivot (2-axis pivoting design) 25 = 25,000 lbs. - - F = Flat Deck (has 2-axis pivot design) - - G = Gooseneck ( ball-type hitch) Examples: 24-UL-16 24-SLP-21 24-SLF-21 24-in. wide Ultra model, 16,000 lbs. GVW capacity. 24-in. wide Slider model, Double Pivot design, 21,000 lbs. GVW cap 24-in. wide Slider model, Flat Deck (double pivot), 21,000 lbs. GVW cap. The complete HIJACKER FIFTH WHEEL HITCHES product line is as follows: 24-UL-16 24-ULP-16 24-ULP-21 24-ULG-25 24-ULS-16 24-USP-16 24-USP-21 The 24-UL (Ultra) Models all install the same way. The 24-ULS (Ultra Slide) Models all install the same way. 24-SL-16 24-SLP-16 24-SLP-21 24-SLG-25 24-SLF-21 The 24-SL (Slider) Models all install the same way. 34-SL-16 34-SLG-25 The 34-SL Models both install the same way.

General Installation and Safety (*) Instructions 4 ANY DEVIATION FROM RECOMMENDED INSTRUCTIONS MAY VOID WARRANTY OR ACCEPTANCE OF LIABILITY ON THE PART OF VICTORIA INDUSTRIES LTD. 1. TOOLS -- Required for all installations in this manual: Heavy duty drill (1/2 chuck) SHARP drill bits: sizes: 3/4 spanner and socket wrenches Tape measure Vehicle jack and lug wrench (optional) 1/4 (pilot drill) 9/16 1/2 2. REAR TIRE REMOVAL -- Optional to make installation easier. a. FOLLOW TRUCK MANUFACTURER S JACK PLACEMENT INSTRUCTIONS * b. USE JACK STANDS -- DO NOT WORK UNDER VEHICLE SUPPORTED ONLY BY JACK* 3. PARTS a. Check parts list shipped with your particular HIJACKER FIFTH WHEEL HITCH product. b. See Hitch/Truck Combinations page for standard or special brackets required for any vehicle/hitch combination. c. Instruction sheets give our recommended procedure to ensure that the hitch head sits at least even with, or up to 3 ahead of the truck rear axle centerline. 4. DOUBLE CHECK BEFORE DRILLING THAT: * a. No fluid lines or other obstructions are at bolt-hole locations; b. You have not substituted bolts inferior to Grade 5. ~ For further information, contact Victoria Industries Ltd. tel. (250) 386-6231

Hitch/Truck Combinations: Installation Brackets or Kits Required 5 VEHICLE 24-UMS-21 24-UL Models 24-SL Models 34-SL Models FORD 2011 F250/350 Super Duty 2011 F450 Super Duty (6 ½ & 8 Boxes) FB201001 FB001001 FB101001 None Available 2005-2010 F250/350 Super Duty FB201001 F350ULBK or F350SLBK F350SLBK 2008-2010 F450 Super Duty (6 ½ & 8 Boxes) 2004-2011 F150 (6 ½ & 8 Boxes) (NOT for 5 ½ box installs) UM401006 kit 2001-07 F450/550 "Chassis Cab" Will not fit 1999-2004 F250/350 "Super Duty" (6 ½ & 8 Boxes) FB201001 1992-98 F350 (6 ½ & 8 Boxes) Will not fit 1997-98 F250 "Heavy Duty" (6 ½ & 8 Boxes) Will not fit F350ULND F150BK04 or F150ULND 2-411, 1-411AL, 1-411AR 2-411, 1-411EL, 1-411ER 2-411, 1-411AL, 1-411AR 2-411, 1-411AL, 1-411AR F150SLBK kit Not recommended Will not fit Not recommended 6 - Standard 411 6 - Standard 411 6 - Standard 411 6 - Standard 411 6 - Standard 411 6 - Standard 411 1997-99 F250 "Light Duty" (6 ½ & 8 Boxes) Will not fit 4 - Standard 411 6-411D 6 411B 1997-2003 F150 (6 ½ & 8 Boxes) Will not fit 4 - Standard 411 6-411D 6 411B 1989-96 F150/250 (6 ½ & 8 Boxes) Will not fit 2-411, 1-411AL, 1-411AR 6-Standard 411, 2-FB- SLN 6 - Standard 411 2000 & earlier Ranger (6 ½ Boxes) Will not fit Will not fit 6-411B Will not fit 1973-88 F Series (6 ½ & 8 Boxes) Will not fit CHEVROLET 2-411, 1-411AL, 1-411AR 6 - Standard 411 6 - Standard 411 2011 Silverado 2500 & 3500 HD (6 ½ box only) FB202001 FB002001 FB102001 None Available 2011 Silverado 2500 & 3500 HD (8 box only) FB202002 FB002002 FB102001 None Available 2001-2010 Silverado 2500 & 3500 HD (6 ½ & 8 Boxes) (Includes New Body Style) 2007-2011 Silverado &Sierra 1500 (6 ½ Box) (tube frame) 1999-2007 Silverado & Sierra 1500 / 2500 (6 ½ & 8 Boxes) UM401001 kit UM401004 kit 4 - Standard 411 or C3500ULND 4 Standard 411 or C1500ULND 6-411D 6 411B D24SLBK D34SLBK UM401001 kit 4 - Standard 411 6-411D 6 411B 2001-07 Silverado 1500 HD (6 ½ & 8 Boxes) UM401001 kit 4 - Standard 411 6-411D 6 411B 1988-2001 3500 (8 Box) Will not fit 4 - Standard 411 4 411 & 2-411C 4 411 & 2-411B 1988-98 1500 / 2500 (8 Box) Will not fit 4 - Standard 411 4 411 & 2-411C 4 411 & 2-411B 1988-98 1500 / 2500 (6 ½ Box) Will not fit 4 - Standard 411 4 411 & 2-411C 4 411 & 2-411B 1988 & earlier S-10 (6 ½ Box) Will not fit Will not fit 6 - Standard 411 Will not fit 1987 & earlier (6 ½ & 8 Boxes) Will not fit DODGE 2 411 & 2-411AR Not recommended 6 411C 2009 2011 Ram 1500 (6 ½ & 8 Boxes) None Available None Available FB103001 None Available 2002-2008 Ram 1500 (4x2 & 4x4) D1535BK or UM401004 kit (6 ½ and 8 Boxes) (Includes Mega Cab) D1535ND D24SLBK D34SLBK 2003/2011 Ram 2500 (4x2 & 4x4) D1535BK or 2003/2011 RAM 3500 (4x4 only) UM401004 kit D1535ND (6 ½ and 8 Boxes) (Includes Mega Cab ) D24SLBK D34SLBK 2003/2011 Ram 3500 (4x2 only) (6 ½ and 8 Boxes) (Includes Mega Cab ) UM401004 kit D3500BK2 kit D24SLBK D34SLBK 1994-2001 Ram 1500/2500/3500 1994-2002 Ram 2500/3500 (6 ½ & 8 Boxes) Will not fit 4 - Standard 411 6 - Standard 411 6 - Standard 411 1993 & earlier Ram (6 ½ & 8 Boxes) Will not fit 4 - Standard 411 6 - Standard 411 6 - Standard 411 2005 Dakota (6 ½ Box) Will not fit 2003/04 Dakota (6 ½ Box) Will not fit UL05DAK kit or 4 411B 2-411, 1-411AL, 1-411AR SL05DAK kit or 6 Standard 411 Will not fit 6 - Standard 411 Will not fit 2001 & earlier Dakota Will not fit 4 - Standard 411 6 - Standard 411 Will not fit TOYOTA 2001 & earlier Tacoma Will not fit Will not fit 6-411C Will not fit 2001-06 Tundra (6 ½ and 8 Boxes) Will not fit 4 - Standard 411 Not recommended 6 411B 2007-2010 Tundra (6 ½ and 8 Boxes) Will not fit T07ULBK Kit Will not fit ill not fit 2000 & earlier T100 Will not fit 4 - Standard 411 6-411C 6 - Standard 411 NISSAN 2004-07 Titan (6 ½ & 8 Boxes) 2008 Titan (8 Box Only) Will not fit N04F kit Will not fit Will not fit

Optional Frame Brackets 6

Hijacker 7 Hitch Heights The following is a list of the highest and lowest adjustments for the different models of Fifth Wheel Hitches. From bed of truck to top of head: 24 & 34-SL-16 14½ to 17½ 24-UL-16 15 ½ to 18 ½ 24-SLP-16 & 21 15 to 18 24-ULP-16 & 21 16 to 19 24-ULS-16 14 ½ to 17 ½ 24-USP-16 & 21 15 to 18 24-SLF-21 9 24-UMS-21 15 to 18 24-AS-18 17 ¾ to 20 ¼ 24-UAS-18 17 ¼ to 19 ¾

Trouble Shooting Instructions 8 Problem Possible Cause Solution Hitch won t open or close easily Hitch no sitting level when uncoupled Banging and/or bumping felt during stopping and starting from stop Front end of truck feels light and steering feels loose and has swaying Trailer is not sitting level when coupled up (Front to back) Jaw adjustment bolt too tight Trailer weight on locking bar Trailer king pin raised too high Locking bar is gummed up with dirt Trailer is on uneven ground (This should not be a problem if you have a double pivot hitch) Locking bar is bent Single pivot hitch should have some tilt downward towards tailgate only, if some side to side, rubber bumper(s) damaged or missing Jaw adjustment bolt too loose Jaw adjustment bolt missing Trailer hitch weight is light, which may cause bouncing at hitch Trailer hitch weight is too heavy Hitch was installed too far rear of the axle Improper hitch height setting and/or improper king pin height setting Trailer suspension too high or low Truck suspension too high or low Follow procedure for adjusting jaw bolt (see diagram 2) Block trailer wheels, idle truck backwards in reverse, apply parking brake, place in park, re-try to uncouple trailer Lower trailer so front of king pin box contacts the middle of the hitch first. This will let the hitch level itself to allow smooth coupling and uncoupling (see diagram 3) Squirt some WD40 or oil into the locking bar tube, work handle loose, open and close several times, and re-grease locking bar (see diagram 1) Place a piece of wood under the tire of the low side of truck to help level, then uncouple Contact Victoria Industries Limited at: Ph: 250-386-6231 Fax: 250-383-6533 Replace rubber bumpers (available at Victoria Industries Limited) Follow procedure for adjusting jaw bolt (see diagram 2) Install a new bolt and locking nut (available at Victoria Industries Limited) Check trailer manufacturer s hitch weight. Shift weight towards front of trailer Check trailer manufacturer s hitch weight. Shift weight towards back of trailer Re-locate hitch to above or slightly ahead of axle as described in the installation instructions Adjust addle bracket up or down on siderail plates to correct or king pin may need to be adjusted (if adjustable) Axle of trailer can be moved to top or bottom of leaf springs on most trailers to adjust the trailer height Riser block or other suspension extenders may need to be removed from high ground clearance 4x4 s to accommodate trailer

Trouble Shooting Instructions 9 Squirt WD40 or other oil into locking bar tube, open and close locking bar several times, and re-grease. Adjustable Jaw Bolt Setup: Make sure the handle is lubricated between arrows at all times. To do this, pull handle all the way out and turn down then brush with grease. Diagram 1 All Fwh24, FWH24PA, and FWH34 fifth wheel hitch heads are equipped with an adjustable jaw bolt. The jaw bolt is not adjusted at the factory. This allows the customer to set the jaw to the amount of play they prefer to have, in order to couple and uncouple with ease. To adjust, make sure nut B is loosened away from the hitch. With the hitch in the closed or locked position, tighten bolt A up finger tight till it can t go in any more. Then back bolt A off ½ a turn and tighten nut B up against the frame with a ¾ wrench to secure the bolt. This initial adjustment should give the proper amount of play to ensure smooth coupling and uncoupling, as well as a smooth ride. If further adjustment is necessary, repeat the procedure by adjusting the bolt a ¼ turn each time. Bolt A Diagram 2 Nut B Incorrect Correct Diagram 3

Hijacker Double Pivot Head Assembly 10 To attach the FWH24PA hitch head to the 403PA saddle bracket, use the procedure shown below. 1. Pull the pin out of the hitch head and place inside bracket on saddle assembly and insert long attachment pin. 2. Fully insert long pin and attach the locking lynch pin to secure. Revised July 7, 2003

Section 2 --- UL Hitches 11

24-UL-16 12

24-ULP-16 13

24-ULP-21 14

24-ULS-16 15

24-USP-16 16

24-USP-21 17

UL401-IK Installation Kit 18

UL Rail Dimensions 19

Ultra Hitch Install Shim 20 Due to some of the configurations of corrugations in the bed of the box, we supply for use 4-3/8 x 1 ½ x 5 spacers to prevent the box from collapsing in slightly during tightening of the bolts that go down through the box. With the space between the ribs wider and taller on some trucks, the end of the base rails do not span across the valley of the ribs creating a potential for crushing. The following procedures are recommended. **The use of the UL FB washers is not needed when using the 3/8 spacers for installations. Extra 3/8 x 1 ½ x 5 shims are available from Victoria Industries Limited so they can be stocked by the dealer/installers along with any optional frame brackets. 3/8 x 1 ½ x 5 spacer Typical Ultra Install End view showing spacer spanning from flange to flange under the base rail.

F150BK04 Installation Kit 21 This page is a frame specific installation for the 2004-2011 Ford F150 standard 8 and 6 ½ box pickup trucks. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. F150BK04 Contents: 1 F150FD Front Frame Bracket (Driver side) 1 F150FP Front Frame Bracket (Passenger side) 1 F150RD Frame Bracket (Driver side) 1 F150RP Frame Bracket (Passenger side) 4 5/8 x 3 1/2 Bolts NC Plated 4 5/8 Washers NC Plated 4 5/8 Locknuts NC Plated 8 ½ x 1 ½ Knurl Bolts NC Plated 8 ½ Serrated Flange Nuts Plated 1 Fish Wire Use #2 holes for drilling and mounting front base rail. 5/8 x 3 1/2 bolts Bracket F150FP Bracket F150FD Use #3 holes for drilling and mounting rear base rail. Bracket F150RD Bracket F150RP ½ flange nuts on outside with frame brackets (1/2 x 1 ½ knurl bolts feed through from inside of frame)

F350ULBK Installation Kit 22 This is a frame specific installation for the 2005-2010 Ford F250/350 standard 8 and 6 ½ box trucks and 2008-2010 F450 truck installations. Kit for Hijacker Ultra hitch install includes: F350ULBK Contents 2 F350FDS bracket (driver side) 8 1/2 x 1 1/2 hex bolts 2 F350FPS bracket (passenger side) 8 1/2 flat washers 4 5/8 lock nuts 8 1/2 lock nuts 4 5/8 flat washers 4 5/8 x 3 1/2 carriage bolts F350FDS brackets

D1535BK Installation Kit 23 This is a frame specific installation for the 2002-08 Dodge 1500 and 2003-2011 2500 two wheel and four wheel drive trucks and the 3500 Ram four wheel drive pickupp trucks, including the MegaCab models. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. D1535BK Contents: 1 B1535DS Front Frame Bracket (Driver side) 1 A1535PS Front Frame Bracket (Passenger side) 1 C35 Frame Bracket (Driver side) 1 D35 Frame Bracket (Passenger side) 2 5/8 x 3 1/2 Bolts NC Plated 2 5/8 x 6 Bolts NC Plated 4 5/8 Washers NC Plated 4 5/8 Locknuts NC Plated 8 ½ x 1 ½ Knurl Bolts NC Plated 8 ½ Serrated Flange Nuts Plated 1 Fish Wire 5/8 x 3 1/2 bolts Bracket A1535PS 5/8 x 6 bolts Use second hole in for drilling and mounting. C35 Bracket D35 Bracket Bracket B1535DS ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame) ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame) Use inner most hole for drilling and mounting.

D1535ND Installation 24 This is a frame specific installation for the 2002-08 Dodge 1500 and 2003-2011 2500 two wheel and four wheel drive trucks and the 3500 Ram four wheel drive pickup trucks, including the MegaCab models. This installation does not require drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. D1535ND Contents: 1 - Left Front Bracket (#1) 2-1/2-13 x 6 ½ U-Bolt (#12) 1 - Left Front Clamp Bracket (#2) 8-1/2 Wide Flat Washer 1 - Right Front Bracket (#3) 8-1/2-13 Nylon Lock Nut 1 - Right Front Clamp Bracket (#4) 4-1/2-13 x 5 Carriage Bolt 1 - Rear Mounting Bracket (#5) 2-5/8-11 x 3 Hex Bolt 1 - Rear Mounting Bracket (#6) 2-5/8-11 x 5 ½ Hex Bolt 1 - Spacer U-Bracket 4-5/8 Wide Flat Washer 4-3/4 Spacer Plate 2-5/8 Standard Flat Washer 2-2 3/8 Tube Spacer 4-5/8 Lock Washer 4 - Spacer Plate 2-5/8-11 Hex Nut 1-1/2-13 x 5 ½ U-Bolt

D3500BK2 Installation 25 This is a frame specific installation instruction for the 2003-2011 Dodge 3500 Ram 4x2 pickup trucks including the MegaCab models. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. D3500BK2 Contents: 1 A3500DS Front Frame Bracket (Driver side) 1 A3500PS Front Frame Bracket (Passenger side) 1 C35 Frame Bracket (Driver side) 1 D35 Frame Bracket (Passenger side) 2 5/8 x 3 1/2 Bolts NC Plated 2 5/8 x 6 Bolts NC Plated 4 5/8 Washers NC Plated 4 5/8 Locknuts NC Plated 8 ½ x 1 ½ Knurl Bolts NC Plated 8 ½ Serrated Flange Nuts Plated 1 Fish Wire 5/8 x 3 1/2 bolts Bracket A3500PS Use outside holes for drilling and mounting. 5/8 x 6 bolts D35 Bracket Bracket A3500DS ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame) ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame) C35 Bracket Use inner most hole for drilling and mounting.

T07ULBK Installation 26 This is a frame specific installation for the UL model hitches in 2007-2010 Toyota Tundra 6 ½ foot and 8 foot box pickup trucks. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. T07ULBK Contents: 2 411 Frame Brackets 1 411AL Frame Bracket 1 Frame Spacer Plate 4 5/8 Flange nuts NC Plated 3 5/8 x 3 Carriage Bolts 1 5/8 x 5 Carriage Bolt 6 ½ x 1 ½ Bolts Plated 6 ½ Lock Nuts Plated 6 ½ Flat Washers Plated Use second holes for drilling and mounting rear base rail. Drill through top of frame on passenger side only and use Frame Spacer Plate as shown. 5/8 x 3 carriage bolts 5/8 x 5 carriage bolt Use outside holes for drilling and mounting front base rail. Frame Spacer Plate 411AL Frame Bracket 411 Frame Bracket 5/8 flange nut

N04F Installation 27 This is a frame specific installation for the 2004-07 Nissan Titan pickup trucks with 8 and 6 ½ boxes and the 2008 8 box. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. N04F Contents: 2 411F Frame Brackets 2 411 Frame Brackets 4 5/8 x 3 1/2 Bolts NC Plated 4 5/8 Washers NC Plated 4 5/8 Locknuts NC Plated 4 ½ x 2 x 5 Plates 8 ½ x 1 ½ Knurl Bolts NC Plated 8 ½ Serrated Flange Nuts Plated 1 Fish Wire Use end holes for drilling and mounting. 5/8 x 3 1/2 bolts 411F Bracket 411 Bracket ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame)

UL05DAK Installation 28 This is a frame specific installation instruction for the 2005 Dodge Dakota with the 6 1/2 box. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. UL05DAK Contents: 4 411B Frame Brackets 4 5/8 x 3 1/2 Bolts NC Plated 4 5/8 Washers NC Plated 4 5/8 Locknuts NC Plated 8 ½ x 1 ½ Knurl Bolts NC Plated 8 ½ Serrated Flange Nuts Plated 1 Fish Wire (not shown) Use end holes for drilling and mounting. 5/8 x 3 1/2 bolts 1/2 x 1 ½ knurl bolts feed through from inside of frame ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame) 411B brackets

FB001001 Installation Kit 29 This is a frame specific installation for the 2011 Ford F250/350 standard 8 and 6 ½ box trucks and 2011 F450 truck installations. Kit for Hijacker Ultra hitch install includes: 1 Driver Side Frame Bracket 2 ¾ x 2 ½ Hex Bolts NC Plated 1 Passenger Side Frame Bracket 2 ¾ Flat Washers Plated 4 5/8 x 3 1/2 Bolts NC Plated 2 ¾ Nylon Lock Nuts NC Plated 8 5/8 Washers NC Plated 1 ½ x 1 ½ Knurl Bolt NC Plated 4 5/8 Locknuts NC Plated 1 ½ Serrated Flange Nut Plated 3 ½ x 1 ½ Hex Bolts NC Plated 1 Fish Wire (not shown) 3 ½ Flat Washers Plated 3 ½ Nylon Lock Nuts NC Plated Use end holes for drilling and mounting. 5/8 x 3 1/2 bolts ½ flange nut (1/2 x 1 ½ knurl bolt feeds through from inside of frame at this hole only)

FB002001 Installation Kit 30 This is a frame specific installation for the 2011 Chev and GMC Sierra 6 ½ box truck installations. Kit for Hijacker Ultra hitch install includes: 1 Driver Side Frame Bracket 4 Slotted Base Rail Shims 1 Passenger Side Frame Bracket 4 Carriage Bolt Plates 4 5/8 x 3 Bolts NC Plated 4 5/8 x 2 Carriage Bolts NC Plated 8 5/8 Washers NC Plated 4 5/8 Serrated Flange Nuts Plated 4 5/8 Locknuts NC Plated 1 Fish Wire (not shown) Use second holes in from end for drilling and mounting. 5/8 x 3 bolts 5/8 x 2 carriage bolts & bolt plates feed through from inside of frame 5/8 flange nuts (5/8 x 2 carriage bolts & bolt plates feed through from inside of frame)

FB002002 Installation Kit 31 This is a frame specific installation for the 2011 Chev and GMC Sierra 8 box truck installations. Kit for Hijacker Ultra hitch install includes: 1 Driver Side Frame Bracket 4 Slotted Base Rail Shims 1 Passenger Side Frame Bracket 4 Carriage Bolt Plates 4 5/8 x 3 Bolts NC Plated 4 5/8 x 2 Carriage Bolts NC Plated 8 5/8 Washers NC Plated 4 5/8 Serrated Flange Nuts Plated 4 5/8 Locknuts NC Plated 1 Fish Wire (not shown) Use second holes in from end for drilling and mounting. 5/8 x 3 bolts 5/8 flange nuts (5/8 x 2 carriage bolts & bolt plates feed through from inside of frame) 5/8 x 2 carriage bolts & bolt plates feed through from inside of frame

FORD: 1973-88 F Series 2.100 HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two 5/8 holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), the 411-AL (front driver s side), 411-AR (front passenger s side) and 411 (rear) brackets, SAE flat washers and locknuts onto carriage bolts. b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1989-96 F150 / F250 6 ½ & 8 Box 2.101 HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two 5/8 holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), the 411-A (front) and 411 (rear) brackets, SAE flat washer and locknut in place onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1992-98 F350 8 Box 2.102 FORD: 1997-98 F250 Heavy Duty 6 ½ & 8 Box HIJACKER HITCH: 24-UL Models INSTALLATION June 8, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 31 3/4 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two 5/8 holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), the 411-A (front) and 411 (rear) brackets, SAE flat washer and locknut in place onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1997 F250 Light Duty 6 ½ & 8 Box 2.103 HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 1/4 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, THIRD HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1997-2003 F150 6 ½ & 8 Box 2.104 1998 F250 Light Duty 6 ½ & 8 Box HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 1/4 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, THIRD HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 80 FT.LBS.

FORD: 1999-2004 F250 / F350 Super Duty 6 ½ & 8 Box 2.105 HIJACKER HITCH: 24-UL Models INSTALLATION March 23, 2006 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 1/4 from back edge of truck box to square hole centers in rear bedrail. This will place the hitch 1/2 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. b. Drop in two 5/8 x 3 1/2 carriage bolts. c. Drill two 5/8 holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two 5/8 x 3 1/2 carriage bolts. 4. a. Under box, loosely install the 411(front) brackets and 411E (rear) brackets, FB washers 5/8 flat washers and locknuts in place onto the carriage bolts (4 places). On 2005-06 models the F350ULBK install kit will be required. See install 2.02 b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1999-2000 F250 Light Duty 6 ½ & 8 Box 2.106 HIJACKER HITCH: 24-UL Models INSTALLATION June 8, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 1/4 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, THIRD HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 2000-2007 F450 / F550 Super Duty 2.107 HIJACKER HITCH: 24-UL Models only INSTALLATION Jan. 17, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 37 1/2 from back edge of truck frame to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two 5/8 x 3 1/2 carriage bolts. c. Drill two 5/8 holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two 5/8 x 3 1/2 carriage bolts. 4. a. Under box, loosely install the 411A (front) brackets and 411 (rear) brackets, FB washers 5/8 flat washers and locknuts in place onto the carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 2004-2011 F150 6 ½ & 8 Boxes (NOT for 5 ½ box install) 2.108 HIJACKER HITCH: 24-UL Model (F150BK04 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 ½ from back edge of truck box to square hole centers in rear bed rail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two 5/8 dia. holes thru FRONT BEDRAIL, 2 nd HOLE POSITION, as shown. Use bed rail with the 3 square holes in the end. Drop in two 5/8 x 3 ½ bolts. b. Drill two holes in REAR BEDRAIL, 3 rd HOLE POSITION. Drop in two 5/8 x 3 1/2 bolts. 4. a. Use frame brackets F150FD (drivers side) and F150FP (passenger side) on front base rail #1 and frame brackets F150RD (drivers side) and F150RP (passenger side) on rear base rail #2. Brackets will be bolted onto frame by drilling frame and fishing bolt and lock washer through frame with a fish wire and attach with flange nut on outside of bracket. Find access holes in the frame as shown on diagram. These can be used to fish the bolt and lock washers through. b. Under box, loosely install rear frame brackets first, using 5/8 SAE flat washers and lock nuts onto 5/8 bolts. Hold rear brackets up against the frame and tighten up under the box. Using the holes in the frame bracket as guides, drill 9/16 holes into frame. Fish 1/2 bolts and lock washers through access hole 1 and fasten with 1/2 flange nuts on outside of frame bracket. c. Repeat with front brackets using access hole 2 for fishing the bolts and lock washers through. 5. a. BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Use an air impact gun to fasten brackets with ½ x 1 1/2 long hex bolts and flange nuts for all brackets. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 2005-2010 F250/350 Super Duty 6 ½ & 8 Box 2.109 2008-2010 F450 Super Duty 6 ½ & 8 Box HIJACKER HITCH: 24-UL Models (F350ULBK install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 1/4 from back edge of truck box to square hole centers in rear bedrail. This will place the hitch 1/2 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. b. Drop in two 5/8 x 3 1/2 carriage bolts. c. Drill two 5/8 holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two 5/8 x 3 1/2 carriage bolts. 4. a. Under box, loosely install the F350ULBK brackets, FB washers, 5/8 flat washers and locknuts in place onto the carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 80 FT.LBS.

FORD: 2011 F250/350 Super Duty 6 ½ & 8 Box 2.110 2011 F450 Super Duty 6 ½ & 8 Box HIJACKER HITCH: 24-UL Models (FB001001 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 from back edge of truck box to square hole centers in rear bedrail. This will place the hitch 1 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. Attach base rails and frame brackets using the frame specific instructions that came with the FB001001 installation bracket kit.

CHEVROLET: 1981-87 Pickups 2.200 HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 34 1/2 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. b. Drop in two extra-long (5/8 x 5 long) carriage bolts. c. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two (5/8 x 3 1/2 long) carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts: use standard 411 bracket on driver s side front and passenger side rear; use special 411-AR bracket in remaining two positions. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEVROLET: 1988-97 1500 / 2500 6 ½ Box 2.201 HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 28 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEVROLET: 1988-98 1500/2500/3500 8 Box 2.202 1998-2000 3500 8 Box HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 34 1/4 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washer and lock nut. c. Press bracket tight against frame member; tighten nut snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 1998-99 1500/2500 6 ½ Box 2.203 1998-2000 3500 6 ½ Box HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 28 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 1999-2007 Silverado & Sierra 1500/2500 6 ½ Box 2.204 2001-02 1500 HD 6 ½ Box HIJACKER HITCH: 24-UL Models INSTALLATION Feb. 5, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 28 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 1999-2007 Silverado & Sierra 1500/2500 8 Box 2.205 HIJACKER HITCH: 24-UL Models INSTALLATION Feb. 5, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2003-07 Silverado & Sierra 1500 & 1500 HD 6 ½ Box 2.206 HIJACKER HITCH: 24-UL Models INSTALLATION Feb. 5, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 28 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD 8 Box 2.207 HIJACKER HITCH: 24-UL Models INSTALLATION Nov. 16, 2006 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 33 3/4 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD 6 ½ Box 2.208 HIJACKER HITCH: 24-UL Models INSTALLATION Nov. 16, 2006 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 30 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2001-07 Silverado & Sierra 3500 HD 8 Box 2.209 HIJACKER HITCH: 24-UL Models INSTALLATION Nov. 16, 2006 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 34 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 2007-2011 Silverado & Sierra 1500 6½ Box (tube frame) 2.210 HIJACKER HITCH: 24-UL Models INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 27 1/2 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. Slide 3/8 plated shims under base rails in valley closest to carriage bolt at both ends. 4. a. Under box, place FB washers (2 wide flat bar) and frame brackets onto carriage bolt. b. Loosely install SAE washers and lock nuts. c. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Brackets will be bolted onto frame by drilling frame and fishing knurl bolt through frame with a fish wire and attach with hex nut and lock washer on outside of bracket. Use a 1/2 drill for holes.* -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long knurl bolts, hex nuts, and lock washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD 6 ½ Box (New Style) 2.211 HIJACKER HITCH: 24-UL Models INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 28 1/2 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. d. Place a plated shim under base rail in bed depression closest to each bolt (see above). 4. a. Under box, place frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 2007-2010 Silverado & Sierra 2500 HD 8 Box (New Style) 2.212 HIJACKER HITCH: 24-UL Models INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 34 1/2 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. d. Place a plated shim under base rail in bed depression closest to each bolt (see above). 4. a. Under box, place frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. b. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2007-2010 Silverado & Sierra 3500 HD 8 Box (New style) 2.213 HIJACKER HITCH: 24-UL Models INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 33 1/2 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, SECOND HOLE POSITION. Drop in two carriage bolts. d. Place a plated shim under base rail in bed depression closest to each bolt (see above). 4. a. Under box, place frame brackets onto carriage bolts. b. Loosely install SAE washers and lock nuts. c. Press brackets tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets to frame with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2011 Silverado & Sierra 2500/3500 HD - 6 1/2 Box 2.214 HIJACKER HITCH: 24-UL Models (FB002001 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 3/8 from back edge of truck box to square hole centers in rear bedrail. This will place the hitch 1 1/2 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. Attach base rails and frame brackets using the frame specific instructions that came with the FB002001 installation bracket kit.

CHEV/GMC: 2011 Silverado & Sierra 2500/3500 HD - 8 Box 2.215 HIJACKER HITCH: 24-UL Models (FB002002 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 3/8 from back edge of truck box to square hole centers in rear bedrail. This will place the hitch 1 1/2 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. Attach base rails and frame brackets using the frame specific instructions that came with the FB002002 installation bracket kit.

DODGE: 1993 & Earlier Ram 2.300 HIJACKER HITCH: 24-UL Models INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 37 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, THIRD HOLE POSITION, as shown. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 1994-2001 RAM 1500 6 ½ Box 2.301 1994-2002 RAM 2500/3500 6 ½ Box HIJACKER HITCH: 24-UL Model INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 31 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Use OUTSIDE hole locations, front and rear. Drop in two carriage bolts. b. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two carriage bolts. You will have to use two 5/8 x 5 long bolts to go through cross member. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 1994-97 RAM 1500 / 2500 / 3500 8 Box 2.302 HIJACKER HITCH: 24-UL Model INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 35 1/2 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Use OUTSIDE hole locations, front and rear. Drop in two carriage bolts. b. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two carriage bolts. You will have to use two 5/8 x 5 long carriage bolts to go through cross member. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 1998-2001 RAM 1500 8 Box 2.303 1998-2002 RAM 2500/3500 8 Box HIJACKER HITCH: 24-UL Model INSTALLATION Jan. 31, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 34 1/2 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Use OUTSIDE hole locations, front and rear. Drop in two 5/8 x 3 ½ carriage bolts. b. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two 5/8 x 5 carriage bolts to go through the cross member. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2002-08 RAM 1500 (4x2 & 4x4) 6 ½ & 8 Box (includes MegaCab) 2.304 2003-2011 RAM 2500 (4x2 & 4x4) 6 ½ & 8 Box (includes MegaCab) 2003-2011 RAM 3500 (4x4 only) 6 ½ & 8 Box (includes MegaCab) HIJACKER HITCH: 24-UL Model (D1535BK install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 (short box) or 34 (long box) from back edge of truck box to square hole centers in rear bed rail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two 5/8 dia. holes thru FRONT BEDRAIL, SECOND HOLE POSITION, as shown. Use bed rail with the 3 square holes in the end. Drop in two 5/8 x 3 ½ bolts. b. Drill two holes in REAR BEDRAIL, INSIDE POSITION. Drop in two 5/8 x 6 bolts. **You will have to use the two 5/8 x 6 long bolts to go through cross member. Frame bracket will mount inside frame facing inwards as shown in circled close up. 4. a. Under box, loosely install frame brackets, SAE flat washers and lock nuts onto 5/8 bolts (4 places). b. Use frame brackets B1535DS (drivers side) and A1535PS (passenger side) on front base rail #1 and frame brackets C35 (drivers side) and D35 (passenger side) on rear base rail #2. Brackets will be bolted onto frame by drilling frame and fishing knurl bolt through frame with a fish wire and attach with flange nut on outside of bracket. There are access holes just behind the rear cross member. These can be used to fish the knurl bolt through. Use a 1/2 drill for holes. 5. a. BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Use an air impact gun to fasten brackets with ½ x 1 1/2 knurl bolts and flange nuts for all brackets. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2003-2011 3500 (4x2 models only) 6 ½ & 8 Box 2.305 HIJACKER HITCH: 24-UL Model (D3500BK2 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 (short box) or 34 (long box) from back edge of truck box to square hole centers in rear bed rail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two 5/8 dia. holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Use bed rail with the 3 square holes in the end. Drop in two 5/8 x 3 ½ bolts. b. Drill two holes in REAR BEDRAIL, INSIDE POSITION. Drop in two 5/8 x 6 bolts. **You will have to use the two 5/8 x 6 long bolts to go through cross member. Frame bracket will mount inside frame facing inwards as shown in circled close up. 4. a. Under box, loosely install frame brackets, SAE flat washers and lock nuts onto 5/8 bolts (4 places). b. Use frame brackets A3500D (drivers side) and A3500P (passenger side) on front base rail #1 and frame brackets C35 (drivers side) and D35 (passenger side) on rear base rail #2. Brackets will be bolted onto frame by drilling frame and fishing knurl bolt through frame with a fish wire and attach with flange nut on outside of bracket. Front brackets will use existing frame hole under the cross member for the bottom hole in bracket so only one hole need be drilled. There are access holes just behind the rear cross member. These can be used to fish the knurl bolt through. Use a 1/2 drill for holes. 5. a. BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with ½ x 1 1/2 knurl bolts and flange nuts for all brackets. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2001 & Earlier Dakota 2.306 HIJACKER HITCH: 24-UL Model INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, THIRD HOLE POSITION, as shown - NOTE: use OUTSIDE hole locations instead, front and rear, if desired. b. Drop in two carriage bolts. c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2003-04 Dakota 6 ½ Box (does not include Quad Cab) 2.307 HIJACKER HITCH: 24-UL Model INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 28 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, THIRD HOLE POSITION, as shown - NOTE: use OUTSIDE hole locations instead, front and rear, if desired. b. Drop in two carriage bolts. ** (5/8 x 3 hex head gr. 5 bolts can be substituted instead of using the carriage bolts because of space restrictions under the box. This will allow the bolts to be easily tightened from up top). c. Drill two holes in REAR BEDRAIL, THIRD HOLE POSITION. Drop in two bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411AR (driver side) front frame bracket and 411AL (pass. side) front frame bracket, 411 frame brackets on rear rail, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2005 Dakota 6 1/2 Box 2.308 HIJACKER HITCH: 24-UL Model (UL05DAK install kit required) INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 29 3/4 from back edge of truck box to square hole centers in rear bed rail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two 5/8 dia. holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Drop in two 5/8 x 3 ½ bolts. b. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two 5/8 x 3 1/2 bolts. Frame bracket will mount outside of frame facing outwards as shown in circled close up. 4. a. Under box, install the 411B frame brackets, SAE flat washers and lock nuts onto 5/8 bolts (4 places). Tighten bolts. b. Brackets will be bolted onto frame by drilling frame (use holes in frame brackets as guides) and fishing 1/2 x 1 1/2 knurl bolts (supplied with install kit # UL05DAK) through frame with a fish wire and attach with serrated flange nut on outside of bracket. There are access holes in the frame that can be used to fish the knurl bolt through. Use a 1/2 drill for holes. 5. a. BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Use an air impact gun to fasten brackets with ½ x 1 1/2 knurl bolts and flange nuts for all brackets. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

TOYOTA: 2000 & earlier T100 Regular & Extended Cab (includes 4x4) 2.400 HIJACKER HITCH: 24-UL Model INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 39 from back edge of truck box to square hole centers in rear bedrail. This places hitch 2 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstructions (frame members, etc.) 3. a. Drill two 5/8 dia. holes thru FRONT bedrail, OUTSIDE position as shown. b. Drop in two 5/8 x 3 1/2 long carriage bolts. c. Drill two holes in REAR bedrail, OUTSIDE position. Drop in two carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and locknuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 4 long hex bolts (not supplied), washers, & nuts. This installation will require 4 long ½ bolts to go through box frame. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

TOYOTA: 2000-2006 Tundra Regular & Extended Cab (includes 4x4) 2.401 HIJACKER HITCH: 24-UL Model INSTALLATION June 9, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 35 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Use OUTSIDE hole locations, front and rear. Drop in two 5/8 x 3 ½ carriage bolts. b. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two 5/8 x 3 ½ carriage bolts. 4. a. Under box, loosely install FB washers (2 wide flat bar), 411 frame brackets, SAE flat washers and lock nuts onto carriage bolts (4 places). b. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

TOYOTA: 2007-2010 Tundra Reg & Extended Cab 6 ½ & 8 Box 2.402 HIJACKER HITCH: 24-UL Model (T07ULBK install kit required) 5/8 flange nut INSTALLATION Nov. 11, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 from back edge of truck box to square hole centers in rear bedrail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two dia. 5/8 holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Use OUTSIDE hole locations, front and rear. Drop in two 5/8 x 3 ½ carriage bolts. b. Drill two holes in REAR BEDRAIL, 2 nd HOLE POSITION. Drop in 5/8 x 3 carriage bolt on driver side and save 5/8 x 5 carriage bolt for passenger side. NOTE: On passenger side rear hole, drill down through top of frame as well. 4. a. Under box, loosely install frame brackets and 5/8 flange nuts onto carriage bolts on both driver side and front passenger side brackets (3 places). b. On rear passenger side place spacer block between top of frame and under side of box. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

NISSAN: 2004-07 Titan 6 ½ & 8 Box Extended Cab 2.500 HIJACKER HITCH: 24-UL Model (N04F install kit required) FB shim 411F INSTALLATION Jan. 17, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 33 1/2 from back edge of truck box to square hole centers in rear bed rail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two 5/8 dia. holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Drop in two 5/8 x 3 ½ bolts. b. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two 5/8 x 3 1/2 bolts. 4. a. Under the box, loosely install frame brackets, FB shim, SAE flat washers and lock nuts onto 5/8 bolts (see drawing below). b. Use the longer 411F frame brackets on front base rail #1 and standard 411 frame brackets on rear base rail #2. Brackets will be bolted onto frame by drilling frame and fishing knurl bolt through frame with a fish wire and attach with flange nut on outside of bracket. Use a 1/2 drill for holes. 5. a. BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Use an air impact gun to fasten brackets with ½ x 1 1/2 knurl bolts and flange nuts for all brackets. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

NISSAN: 2008 Titan 8 Box Only 2.501 HIJACKER HITCH: 24-UL Model (N04F install kit required) INSTALLATION: Oct. 1, 2008 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 32 from back edge of truck box to square hole centers in rear bed rail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. Drill two 5/8 dia. holes thru FRONT BEDRAIL, OUTSIDE POSITION, as shown. Drop in two 5/8 x 3 ½ bolts. b. Drill two holes in REAR BEDRAIL, OUTSIDE POSITION. Drop in two 5/8 x 3 1/2 bolts. 4. a. Under the box, loosely install frame brackets, SAE flat washers and lock nuts onto 5/8 bolts. Place FB shim under ends of base rails in valley (see inset above). b. Use the longer 411F frame brackets on front base rail #1 and standard 411 frame brackets on rear base rail #2. Brackets will be bolted onto frame by drilling frame and fishing knurl bolt through frame with a fish wire and attach with flange nut on outside of bracket. Use a 1/2 drill for holes. 5. a. BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Use an air impact gun to fasten brackets with ½ x 1 1/2 knurl bolts and flange nuts for all brackets. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

Section 3 --- SL Hitches 32

24-SL-16 33

24-SLP-16 34

24-SLP-21 35

34-SL-16 36

24-SLF-21 37

24 SL Rail Dimensions 38

34 SL Rail Dimensions 39

F150SLBK Installation 40 This is a frame specific installation instruction for the 2004-2011 Ford F150 Regular and Super Cab pickup trucks. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. F150SLBK Contents: 1 F150SLD Frame Bracket (Driver side) 1 F150SLP Frame Bracket (Passenger side) 6 1/2 x 3 Bolts NC Plated 6 1/2 Washers NC Plated 6 1/2 Locknuts NC Plated 6 3/16 x 1 1/2 square Plated Washers 8 ½ x 1 ½ Knurl Bolts Plated 8 ½ Serrated Flange Nuts Plated 1 Fish Wire F150SLD Frame Bracket 1/2 x 3 bolts Cab F150SLP Frame Bracket ½ flange nuts on outside with frame brackets (1/2 x 1 ½ knurl bolts feed through from inside of frame) Tailgate

F350SLBK Kit 41 2005-2010 Ford F250/350 & 2008-2010 F450 installation kit for Hijacker SL hitch installs includes: 4 411 brackets 12 1/2 x 1 1/2 hex bolts 1 F350FPS bracket 18 1/2 flat washers 1 F350FDS bracket 18 1/2 lock nuts 6 SL107 square washers 6 ½ x 3 bolts 24-SL install shown. 34-SL install would have brackets turned to the outside of the frame.

D24SLBK Installation 42 This is a frame specific installation instruction for the 24-SL-16 hitch in 2002-08 Dodge Ram1500 and 2003-2011 Ram 2500 & 3500 two wheel and four wheel drive pickup trucks (including the MegaCab models) and the 2007-2011 Chev & GMC 1500 pick up truck with tubular frame. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. D24SLBK Contents: 6 411D Frame Brackets 6 1/2 x 3 Bolts NC Plated 6 1/2 Flat Washers NC Plated 6 1/2 Locknuts NC Plated 6 SL107 Square Washers Plated 12 ½ x 1 ½ Knurl Bolts NC Plated 12 ½ Serrated Flange Nuts Plated 1 Fish Wire Use holes 2, 3, and 4 for drilling and mounting. 1/2 x 3 bolts SL107 Square washer 411D Bracket ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame)

D34SLBK Installation 43 This is a frame specific installation instruction for the 34-SL 16 hitch on 2002-08 Dodge Ram1500 and 2003-2011 Ram 2500 & 3500 two wheel and four wheel drive pickup trucks (including the MegaCab models) and the 2007-2011 Chev & GMC 1500 pickup trucks. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. D34SLBK Contents: 6 411BB Frame Brackets 6 1/2 x 3 Bolts NC Plated 6 1/2 Flat Washers NC Plated 6 1/2 Locknuts NC Plated 6 SL107 Square Washers Plated 12 ½ x 1 ½ Knurl Bolts NC Plated 12 ½ Serrated Flange Nuts Plated 1 Fish Wire Use holes 2, 3, and 4 for drilling and mounting. 1/2 x 3 bolts 411BB Frame Bracket ½ flange nuts (1/2 x 1 ½ knurl bolts feed through from inside of frame)

SL05DAK Installation 44 On the reverse side of this page is a frame specific installation instruction for the 2005 Dodge Dakota with the 6 1/2 box. This installation requires drilling of the frame for frame brackets. Below is a view of the parts and how they are installed. SL05DAK Contents: 6 411 Frame Brackets 6 1/2 x 3 Bolts NC Plated 6 1/2 Flat Washers NC Plated 6 1/2 Lock Nuts NC Plated 6 1 1/2 Square Plate Washers 12 ½ x 1 ½ Knurl Bolts NC Plated 12 ½ Serrated Flange Nuts Plated 1 Fish Wire (not shown) 1/2 x 3 Bolts 1/2 Flat Washers 1 1/2 Square Plate Washers & 1/2 Lock Nuts 411 Brackets 1/2 x 1 ½ knurl bolts feed through from inside of frame 1/2 flange nuts

FB101001 Installation Kit 45 This is a frame specific installation for the 2011 Ford F250/350 standard 8 and 6 ½ box trucks and 2011 F450 truck installations. Kit for Hijacker SL hitch install includes: 1 Driver Side Frame Bracket 2 3/4 x 2 1/2 Hex Bolts NC Plated 1 Passenger Side Frame Bracket 2 3/4 Flat Washers Plated 6 1/2 x 3 1/2 Bolts NC Plated 2 3/4 Nylon Lock Nuts NC Plated 9 1/2 Washers NC Plated 1 1/2 x 1 1/2 Knurl Bolt NC Plated 9 1/2 Locknuts NC Plated 1 1/2 Serrated Flange Nut Plated 3 1/2 x 1 1/2 Hex Bolts NC Plated 1 Fish Wire (not shown) 6 Square Flat Washers Plated Use holes #1, #3 and #5 for drilling and mounting. 1/2 x 3 1/2 bolts ½ flange nut (1/2 x 1 ½ knurl bolt feeds through from inside of frame at this hole only) Square Flat Washers

FB102001 Installation Kit 46 This is a frame specific installation for the 2011 Chev and GMC Sierra 6 ½ and 8 box truck installations. Kit for Hijacker SL hitch install includes: 1 Driver Side Frame Bracket 6 Square Flat Washers Plated 1 Passenger Side Frame Bracket 4 Carriage Bolt Plates 6 1/2 x 3 Bolts NC Plated 4 5/8 x 2 Carriage Bolts NC Plated 6 1/2 Washers NC Plated 4 5/8 Serrated Flange Nuts Plated 6 1/2 Locknuts NC Plated 1 Fish Wire (not shown) Use holes #1, #3 and #4 for drilling and mounting. 1/2 x 3 bolts Square Flat Washers 5/8 flange nuts (5/8 x 2 carriage bolts & bolt plates feed through from inside of frame) 5/8 x 2 carriage bolts & bolt plates feed through from inside of frame

FB103001 Installation Kit 47 This is a frame specific installation for the 2009-2011 Dodge 1500 6 4 box truck installations. Kit for Hijacker SL hitch install includes: 1 Front Passenger Side Frame Bracket 1 Front Driver Side Frame Bracket 1 Rear Passenger Side Frame Bracket 1 Rear Driver Side Frame Bracket 6 1/2 x 3 Bolts NC Plated 6 Square Flat Washers Plated 6 1/2 Washers NC Plated 4 1/2 x 1 1/2 Knurl Bolt NC Plated 6 1/2 Locknuts NC Plated 4 1/2 Serrated Flange Nut Plated 2 1/2 x 6 Hex Bolts NC Plated 1 Fish Wire (not shown) 2 1/2 Lock Washers Plated Use holes #2, #5 and #6 for drilling and mounting. 1/2 x 3 1/2 bolts Front frame brackets must be attached by drilling frame and attaching with knurled bolts and flange nuts Square Flat Washers 1/2 x 6 bolt and lock washer feed through from bottom of frame and thread into frame bracket Rear frame bracket

FORD: 1973-88 F SERIES 3.100 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 24 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #5 and #6, each bedrail. Drop in four remaining hex bolts. 3. Note: The SL-34 installs outside the frame. 4. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1989-96 F150 / F250 6 ½ & 8 Box 3.101 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 22 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) on bolts #1 and #3, and FB-SLN sliding nuts on 2 rear bolts #6, and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1992-98 F350 8 Box 3.102 1997-98 F250 Heavy Duty 6 ½ & 8 Box HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 23 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #6, each bedrail. Drop in four remaining hex bolts. 3. Note: SL-24 Model can use FB-SLN on #6 HOLE. The SL-34 installs outside the frame. 4. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1997 F250 Light Duty 6 ½ & 8 Box 3.103 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 21 3/4 from back edge of truck box to back edge of bedrail. 2. Check underneath box at bolt hole locations for any obstructions (frame members, etc.) 3. a. Drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #5, each bedrail. Drop in four remaining hex bolts. 4. a. Under box, place 411-D (or 411-B for SL-34) frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1997-2003 F150 6 ½ & 8 Box 3.104 1998 F-250 Light Duty 6 ½ & 8 Box HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Oct 18, 2000 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 21 3/4 from back edge of truck box to back edge of bedrail. 2. Check underneath box at bolt hole locations for any obstructions (frame members, etc.) 3. a. Drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 4. a. Under box, place 411-D (or 411-B for SL-34) frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1998 & Earlier Ranger 3.105 HIJACKER HITCH: 24-SL Model INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 23 3/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 3. Note: SL-24 Model can use FB-SLN on #6 HOLE. 4. a. Under box, place 411-B frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1999 Ranger 3.106 HIJACKER HITCH: 24-SL Model INSTALLATION Jan 1, 1999 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 3. Note: SL-24 Model can use FB-SLN on #6 HOLE. 4. a. Under box, place 411-B frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1999-2000 F-250 Light Duty 6 ½ & 8 Box 3.107 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Mar 22, 1999 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 1/4 from back edge of truck box to back edge of bedrail. 2. Check underneath box at bolt hole locations for any obstructions (frame members, etc.) 3. a. Drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 4. a. Under box, place 411-D (or 411-B for SL-34) frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 1999-2004 F250 / F350 Super Duty 6 ½ & 8 Box 3.108 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION March 23, 2004 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 25 (see note) from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #6 (see note), each bedrail. Drop in four remaining hex bolts. 3. Note: The SL-34 installs outside the frame. 4. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). Measure 25 1/2 for the 05-06 trucks and use holes 1, 3, & 4. b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 2004-2011 F150 6 ½ & 8 Boxes (NOT for 5 ½ box installs) 3.109 HIJACKER HITCH: 24-SL Model only (F150SLBK install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 ½ from back edge of truck box to end of the bed rail. 2. Check underneath box at bolt hole locations for any obstruction (frame members, etc.). 3. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1 in each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 4. a. Under box, loosely install frame brackets first, using square plated flat washers and lock nuts onto 1/2 bolts. Hold brackets up against the frame and tighten up under the box. b. Using the holes in the frame bracket as guides, drill 1/2 holes into frame. Fish 1/2 rib neck bolts through access hole (shown) and fasten with 1/2 flange nuts on outside of frame bracket. c. Repeat with bracket on other side. 5. a. BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Use an air impact gun to fasten brackets with ½ x 1 1/2 rib neck bolts and flange nuts for both brackets. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 2005-2010 F250/350 Super Duty 6 ½ & 8 Box 3.110 2008-2010 F450 Super Duty 6 ½ & 8 Box HIJACKER HITCH: 24-SL & 34-SL Models (F350SLBK install kit required) INSTALLATION October 13, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 25 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #4 of each bedrail. Drop in four remaining hex bolts. 3. Note: The SL-34 installs outside the frame. 4. a. Under box, place standard 411 frame brackets onto hex bolts (4 places) and the F350SLBK brackets on the #1 hole hex bolt. b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

FORD: 2011 F250/350 Super Duty 6 ½ & 8 Box 3.111 2011 F450 Super Duty 6 ½ & 8 Box HIJACKER HITCH: 24-SL Models (FB101001 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 23 1/4 from back edge of truck box to the open rear end of each bedrail. This will place the hitch 1/2 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. Attach base rails and frame brackets using the frame specific instructions that came with the FB101001 installation bracket kit.

CHEVROLET: 1981-87 Pickups 3.200 HIJACKER HITCH: 34-SL Models (Note: 34-SL recommended) INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 24 1/8 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place frame brackets 411-C for 34-SL installation (recommended) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEVROLET: 1988-97 1500 / 2500 6 ½ Box 3.201 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 19 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear pin hole position, to parallel bed rails. d. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place two frame brackets 411C (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts in HOLE #1 position. b. Place standard 411 frame brackets onto remaining bolts. c. Loosely install FB washers (1 1/2 square washers) and lock nuts. d. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEVROLET: 1988-98 1500/2500/3500 8 Box 3.202 1998-2000 3500 8 Box HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 25 1/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 (or use alternate #4), and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place two frame brackets 411C (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts in HOLE #1 position. b. Place standard 411 frame brackets onto remaining bolts. c. Loosely install FB washers (1 1/2 square washers) and lock nuts. d. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEVROLET: 1997 & Earlier S-10 3.203 HIJACKER HITCH: 24-SL Model INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 19 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 1998-99 1500/2500 6 ½ Box 3.204 1998-2000 3500 6 ½ Box HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION July 28, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 19 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place two frame brackets 411C (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts in HOLE #1 position. b. Place standard 411 frame brackets onto remaining bolts. c. Loosely install FB washers (1 1/2 square washers) and lock nuts. d. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 1999-2007 Silverado & Sierra 1500/2500 6 ½ Box 3.205 2001-04 1500 HD 6 ½ Box HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Feb. 5, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 19 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. Front bracket will require drilling thru both walls of frame and fasten with ½ x 4 bolts or you can fish ½ x 1 ½ bolt thru inside of frame with thin wire and fasten nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 1999-2007 Silverado & Sierra 1500/2500 8 Box 3.206 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Feb. 5, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 22 1/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. Front bracket will require drilling thru both walls of frame and fasten with ½ x 4 bolts or you can fish ½ x 1 ½ bolt thru inside of frame with thin wire and fasten nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2003-07 Silverado & Sierra 1500 & 1500 HD 6 ½ Box 3.207 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Feb. 5, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 19 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. Front bracket will require drilling thru both walls of frame and fasten with ½ x 4 bolts or you can fish ½ x 1 ½ bolt thru inside of frame with thin wire and fasten nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD 6 ½ Box 3.208 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan. 17, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 3/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. Front bracket will require drilling thru both walls of frame and fasten with ½ x 4 bolts or you can fish ½ x 1 ½ bolt thru inside of frame with thin wire and fasten nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV / GMC: 2001-07 Silverado & Sierra 2500 HD 8 Box 3.209 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 17, 2007 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 24 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. Front bracket will require drilling thru both walls of frame and fasten with ½ x 4 bolts or you can fish ½ x 1 ½ bolt thru inside of frame with thin wire and fasten nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2001-07 Silverado & Sierra 3500 HD 8 Box 3.210 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Nov. 16, 2006 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 27 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2007-2011 Silverado & Sierra 1500 6 ½ Box (tube frame) 3.211 HIJACKER HITCH: 24-SL Model (D24SLBK install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 18 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, of each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #2 and #5, of each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six 411D frame brackets onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long knurl bolts and flange nuts by fishing ½ x 1 ½ bolts thru inside of frame with fish wire and fasten flange nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2007-2011 Silverado & Sierra 1500 6 ½ Box 3.212 HIJACKER HITCH: 34-SL Model (D34SLBK install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 18 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, of each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #2 and #5, of each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six 411BB frame brackets onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long knurl bolts and flange nuts by fishing ½ x 1 ½ bolts thru inside of frame with fish wire and fasten flange nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2007-2010 Silverado & Sierra 2500 HD 6 ½ Box (New Style) 3.213 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 1/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2007-2010 Silverado & Sierra 2500 HD 8 Box (New Style) 3.214 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 25 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2007-2010 Silverado & Sierra 3500 HD 8 Box (New style) 3.215 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 24 1/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame brackets 411D (for 24-SL installation) or 411B (for 34-SL installation) onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

CHEV/GMC: 2011 Silverado & Sierra 2500/3500 HD - 6 1/2 & 8 Box 3.216 HIJACKER HITCH: 24-SL Models (FB102001 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure from back edge of truck box to the open rear end of each bedrail as shown in illustration above. Note different measurements for long and short box. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. Attach base rails and frame brackets using the frame specific instructions that came with the FB102001 installation bracket kit.

DODGE: 1993 & Earlier Ram 3.300 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 25 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. d. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 1994-2001 RAM 1500 6 ½ Box 3.301 1994-2002 RAM 2500/3500 6 ½ Box HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION 18 Oct, 2000 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #6, each bedrail. Drop in four remaining hex bolts. Use hole #5 if truck equipped with overloads. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 1994-97 RAM 1500 / 2500 / 3500 8 Box 3.302 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 25 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear pin hole position, to parallel bed rails d. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 1998-2001 RAM 1500 8 Box 3.303 1998-2002 RAM 2500 & 3500 8 Box HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION Jan 1, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 24 1/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #5, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2002-08 RAM 1500 (4x2 & 4x4) 6 ½ & 8 Box (includes MegaCab) 3.304 2003-2011 RAM 2500/3500 (4x2 & 4x4) 6 ½ & 8 Box HIJACKER HITCH: 24-SL Model (D24SLBK install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 22 ¼ (short box) or 24 ¼ (long box) from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #4, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six 411D frame brackets onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long knurl bolts and flange nuts by fishing ½ x 1 ½ bolts thru inside of frame with fish wire and fasten flange nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2002-08 RAM 1500 (4x2 & 4x4) 6 ½ & 8 Box (includes MegaCab) 3.305 2003-2011 RAM 2500/3500 (4x2 & 4x4) 6 ½ & 8 Box HIJACKER HITCH: 34-SL Model (D34SLBK install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 22 ¼ (short box) or 24 ¼ (long box) from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 2, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Slide hitch to rear position, to parallel bed rails. d. Drill thru HOLES #3 and #4, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place six frame (411BB) brackets onto hex bolts. b. Loosely install FB washers (1 1/2 square washers) and lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long knurl bolts and flange nuts by fishing ½ x 1 ½ bolts thru inside of frame with fish wire and fasten flange nut on outside. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2002 & Earlier Dakota 3.306 HIJACKER HITCH: 24-SL Model INSTALLATION Oct 18, 2000 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 19 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2003 Dakota 6 ½ Box (does not include Quad Cab) 3.307 HIJACKER HITCH: 24-SL Model only INSTALLATION 26 Sept, 2002 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 18 1/4 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1, each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, nuts, washers. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2005 Dakota 6 ½ Box 3.308 HIJACKER HITCH: 24-SL Model only (SL05DAK install kit required) INSTALLATION Nov. 10, 2004 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 1/2 from back edge of truck box to back edge of bedrail. 2. a. First check for obstructions under box, then drill two dia. 17/32 holes thru HOLE # 1 of each bedrail. b. Drop in two dia. 1/2 x 3 long hex bolts. c. Drill thru HOLES #3 and #5, of each bedrail. Drop in four remaining hex bolts. 3. a. Under box, place standard 411 frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 4. The fish wire will be required to fish the bolts through an access hole in the frame. Insert the 1/2 x 1 1/2 knurl bolts (supplied with install kit # SL05DAK) through drilled holes from inside the frame and use flange nuts to fasten on bracket side. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 bolts and flange nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

DODGE: 2009-2011 RAM 1500 6 ½ Box 3.309 HIJACKER HITCH: 24-SL Models (FB103001 install kit required) INSTALLATION December 29, 2010 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 20 3/4 from back edge of truck box to the open rear end of each bedrail. This will place the hitch 1/2 ahead of the axle. 2. Check underneath box at bolt hole locations for any obstruction (gas line, wiring, etc.). 3. Attach base rails and frame brackets using the frame specific instructions that came with the FB103001 installation bracket kit.

TOYOTA: 1998-2001 Tacoma Regular & Extended Cab (includes 4x4) 3.400 HIJACKER HITCH: 24-SL Model only INSTALLATION 18 Oct, 2000 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 21 3/4 from back edge of truck box to back edge of bedrail. This places hitch 1½ ahead of axle. 2. Check underneath box at bolt hole locations for any obstructions (frame members, etc.) 3. a. Drill two 17/32 dia. holes thru HOLE # 2, each bedrail. b. Drop in two 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 4. a. Under box, place 411-C frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. The brackets for hole #2 on each side will require 4 long ½ bolts to go through box frame in front of axle. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

TOYOTA: 2000 & earlier T100 Regular & Extended Cab (includes 4x4) 3.401 HIJACKER HITCH: 24-SL & 34-SL Models INSTALLATION July 20, 1998 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 27 1/4 from back edge of truck box to back edge of bedrail. This places hitch directly over axle. 2. Check underneath box at bolt hole locations for any obstructions (frame members, etc.) 3. a. Drill two 17/32 dia. holes thru HOLE # 2, each bedrail. b. Drop in two 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 4. a. Under box, place 411-C (24-SL) or 411 (34-SL) frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 4 long hex bolts (not supplied), washers, and nuts. These installations will require 4 long ½ bolts to go through box frame. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

TOYOTA: 2000-2005 Tundra Regular & Extended Cab (includes 4x4) 3.402 HIJACKER HITCH: 34-SL Models INSTALLATION Jun 20, 2005 1. a. Completely assemble hitch. See GENERAL INSTRUCTIONS and SAFETY, p. 1.10. b. Set hitch into back of truck, center it side to side. c. Measure 24 1/2 from back edge of truck box to back edge of bedrail. This places hitch directly over axle. 2. Check underneath box at bolt hole locations for any obstructions (frame members, etc.) 3. a. Drill two 17/32 dia. holes thru HOLE # 2, each bedrail. b. Drop in two 1/2 x 3 long hex bolts. c. Drill thru HOLES #4 and #6, each bedrail. Drop in four remaining hex bolts. 4. a. Under box, place 411-B frame brackets onto hex bolts (6 places). b. Loosely install FB washers (1 1/2 square washers) & lock nuts. c. Press each bracket tight against frame member; tighten nuts snug against box. 5. a. Pilot drill* and drill dia.1/2 holes into truck frame, at two places thru holes each frame bracket -- BE CAREFUL OF ELEC. OR FLUID LINES behind frame members. b. Fasten brackets with 1/2 x 1 1/2 long hex bolts, washers, nuts. c. TIGHTEN ALL BOLTS to 90 FT.LBS.

Section 4 --- UMS Hitches 48

24-UMS-21 49

UM401001 Base Rail Kit 50

UM401004 Base Rail Kit 51

UM401005 Base Rail Kit 52

UM401006 Base Rail Kit 53

FB201001 Base Rail Kit 54

FB202001 Base Rail Kit 55

FB202002 Base Rail Kit 56

UMS Base Rail Dimensions 57

Hijacker Underbox Mounting System 4.100 1999-2011 Ford F250/F350 Super Duty 2005-2011 Ford F450 Super Duty (For install in 6 ½ and 8 boxes only) FB201001 General Assembly and Install Instructions Hitch Assembly: 1. Place the base rails on a flat level surface and insert and lock the side rail plates into the base rail holes as shown in the UM402001 instructions. 2. Loosely bolt the saddle bracket (403PA) and the two cross braces to the side rails using the fasteners provided in the UM402001 carton. 3. Tighten all the bolts. 4. Unlock and remove the hitch assembly from the base rails and put to the side for later. Truck Bed Drilling Instructions: Note: On some model years you will have to undo the emergency brake cable from the frame on the driver s side. Reattach after hitch installation. It may also make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. The four 2 diameter holes that need to be drilled through the box are done by the following method: 1. Use the measurements shown in drawing #1 to mark out the four holes that will be drilled through the truck bed. 2. Start out by measuring 37 3/4 from the end of the bottom of the truck bed (tailgate end) to a point on the left side of center of the bed and mark it. Do the same on the right side of center of the bed and mark it. Draw a line across the bed using these two marks as a reference. 3. Measure out and find the center of the truck bed and draw a line from the front to the rear of the bed. 4. Measure out 14 13/16 to either side of the middle centerline slightly ahead of the fender well and slightly behind the fender well. 5. Draw a line between these two points. Do the same on the other side. 6. Measure out (towards the cab) 13 1/2 from the points where the line that goes across the bed intersects with the two lines that are 14 13/16 off the center running the length of the bed. Mark these two points. 7. There should now be four spots marked out for drilling. Double check that the rear to hole marks are exactly 37 3/4 from the end of the bed and that the front holes marks are exactly 13 1/2 forward of those marks. 8. Check the hole marks from side to side and make sure they are exactly 29 5/8 apart from each other. 9. Finally, check for square by measuring diagonally from opposite corners (drawing #2). The measurement should be the same both ways. It should measure 32 9/16.

10. After all the hole marks have been double checked for proper placement, use a center punch and hammer to mark out the spots for drilling. 11. Drill the holes using a 2 hole saw. De-bur the holes using a small file and apply some touch up paint to match colour (not supplied). Drawing #1 Drawing #2

Base Rail Installation: 1. With the four 2 holes drilled in the truck bed, insert the base rails one at a time with hole side up on top of the truck frame at the point just forward of the axle (drawing #3). Insert the first rail all the way to span across to the other side of the frame and slide it back towards the holes closest to the tailgate and position it under the holes. Repeat with the second base rail and position under the forward set of holes. Insert at this point and slide rearward to position under holes Drawing #3 2. With base rails in position below the bed and the base rail holes centered under the holes that were drilled in the bed of the truck, re-install and lock the hitch assembly into the base rails from the top side of the box. 3. Measure and center the entire hitch assembly side to side and front to back so that it is as close to center of the holes in the bed. 4. Attach the frame brackets (oval holes) to the tapped holes in the ends of the base rails using the 1/2 x 1 1/2 bolts and lock washers provided. 5. Tighten the bolts to the base rails. 6. For the 2011 model year installation is a no drill application that uses existing frame holes. See drawings below. 7. For 2010 and earlier models use the holes in the frame bracket plates as a guide and drill the frame in the two smaller mounting holes on each frame bracket with a 33/64 drill bit. You may want to drill smaller pilot holes to make drilling easier. The larger 3/4 hole and bolt is not used for these earlier installs. It is best to install a 1/2 x 1 1/2 bolt, washer, and lock nut after each hole is drilled to ensure there is no shifting of the hitch while drilling the next hole(s). 8. Tighten all bolts.

9. Re-install the rear wheels (if removed), double check all fasteners for tightness, and lower truck (if raised). 10. Unlock and lift the hitch assembly out of the box to make sure it can be removed and inserted with relative ease. If there was any shifting during installation that caused any binding, simply loosen the 4 bolts that attach the base rail to the frame brackets and realign the base rail and retighten. 11. Ensure the side rail locking pins are turned and secured in the locked position with the safety pins. Install the hitch head to the saddle bracket. FB201001 Parts List: 2 Base Rails (Part # UM401005B) 2 Frame Bracket Plates (Part # UM401005A) 7 1/2 x 1 1/2 Bolts (Part # 104) 1 1/2" x 1 1/2 Knurl Bolt 1 1/2" Flange Nut 4 1/2 Lock Washers (Part # 102) 3 1/2 Lock Nuts (Part # 106) 7 1/2 Flat Washers (Part # 105) 2 3/4 x 2 ½ Hex Bolts 2 3/4" Flat Washers 2 3/4 Lock Nuts 4 Bed Plugs (not shown) (Part # UM407) 1 Fish Wire (not shown) 1/2 x 1 1/2" Bolts, 1/2 Lock Washers & 1/2 Flat Washers Base Rails (UM401004B) 1/2 x 1 1/2" Bolts, 1/2 Lock Washers & 1/2 Flat Washers 1/2 x 1 1/2 Knurl Bolt 3/4 Flat Washer & 3/4 Lock Nut Frame Bracket Plates (UM401004A) 1/2 Flange Nut 3/4 x 2 1/2 Bolt

Hijacker Underbox Mounting System 4.101 2004-2011 Ford F150 Pickup Truck (For install in 6 ½ and 8 boxes only) UM401006 General Assembly and Install Instructions Hitch Assembly: Place the base rails on a flat level surface and insert and lock the side rail plates into the base rail holes as shown in the UM402001 instructions. Loosely bolt the saddle bracket (403PA) and the two cross braces to the side rails using the fasteners provided in the UM402001 carton. Tighten all the bolts. Unlock and remove the hitch assembly from the base rails and put to the side for later. Truck Bed Drilling Instructions: Note: It will make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. The four 2 diameter holes that need to be drilled through the box are done by the following method: 1. Use the measurements shown in drawing #1 to mark out the four holes that will be drilled through the truck bed. 2. Start out by measuring 34 1/2 from the end of the bottom of the truck bed (tailgate end) to a point on the left side of center of the bed and mark it. Do the same on the right side of center of the bed and mark it. Draw a line across the bed using these two marks as a reference. 3. Measure out and find the center of the truck bed and draw a line from the front to the rear of the bed. 4. Measure out 14 13/16 to either side of the middle centerline slightly ahead of the fender well and slightly behind the fender well. 5. Draw a line between these two points. Do the same on the other side. 6. Measure out (towards the cab) 13 1/2 from the points where the line that goes across the bed intersects with the two lines that are 14 13/16 off the center running the length of the bed. Mark these two points. 7. There should now be four spots marked out for drilling. Double check that the rear to hole marks are exactly 34 1/2 from the end of the bed and that the front holes marks are exactly 13 1/2 forward of those marks. 8. Check the hole marks from side to side and make sure they are exactly 29 5/8 apart from each other. 9. Finally, check for square by measuring diagonally from opposite corners (drawing #2). The measurement should be the same both ways. It should measure 32 9/16. 10. After all the hole marks have been double checked for proper placement, use a center punch and hammer to mark out the spots for drilling.

11. Drill the holes using a 2 hole saw. De-bur the holes using a small file and apply some touch up paint to match color (not supplied). Drawing #1 Drawing #2

Base Rail Installation: IF the base rails are unable to be slid into position because of insufficient space by the lip of the box bed, then use one of the following two methods to install the base rails. 1. A) Remove the mounting bolts that attach the box to the truck frame on one side only. Raise and block the box high enough so the base rails can be inserted (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Lower and bolt the box back to the frame. Position base rails under holes drilled in bed. OR B) Locate a spot on both sides of the box support cross members on either side of the truck and cut and bend up a 3 1/2 wide section of the sheet metal lip where the bed and the fender well of the box join (drawing # 4). Insert base rails (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Bend the sheet metal back down and position base rails under holes drilled in bed. IMPORTANT: Ensure that the shorter base rail with the angled crossbar is in the position closest to the tailgate with the vertical side of the angle beside the box cross member (drawing #5). Angle allows clearance for motor/pump assembly. Bend up Cut Drawing # 3 Drawing # 4 2. With base rails in position below the bed and the base rail holes centered under the holes that were drilled in the bed of the truck, position one of the 1/2 thick shims under each end of the base rails between them and the top of the frame. Re-install and lock the hitch assembly into the base rails from the topside of the box. Truck Bed Base Rail 1/2 shim Cross member Tailgate Drawing # 5 Drawing # 6

3. Measure and center the entire hitch assembly side to side and front to back so that it is as close to center of the holes in the bed. 4. Attach the frame brackets to the base rails with the end of the frame bracket that has the pair of holes that are closest to each other, towards the cab of the truck (see drawing # 7). Fasten with the 5/8 x 1 3/4 bolts and secure with a 5/8 flat washer and 5/8 lock nut. Truck Cab Access hole Drawing # 7 5. Tighten the bolts to the base rails ensuring that the frame bracket is up against the truck frame. 6. Using the holes in the frame bracket plates as a guide, drill the frame in the four mounting holes on each frame bracket with a 1/2 drill bit. You may want to drill smaller pilot holes to make drilling easier. Insert a 1/2 x 1 1/2 knurl bolt into the drilled hole using the fish wire provided, through the access hole. Secure on the outside of the frame bracket with a flange nut. Do this after the first hole is drilled to ensure there is no shifting of the hitch while drilling the next hole(s). 7. Tighten all bolts. 8. Re-install the rear wheels (if removed), double check all fasteners for tightness, and lower truck (if raised). 9. Unlock and lift the hitch assembly out of the box to make sure it can be removed and inserted with relative ease. If there was any shifting during installation that caused any binding, simply loosen the 4 bolts that attach the base rail to the frame brackets and realign the base rail and retighten. 10.Ensure the side rail locking pins are turned and secured in the locked position with the safety pins. Install the hitch head to the saddle bracket.

UM401006 Parts List: 2 Base Rails 2 Frame Bracket Plates 4 1/2 x 2 x 5 Shims 4 5/8 x 1 3/4 Bolts 4 5/8 Flat Washers 4 5/8 Lock Nuts 8 1/2 x 1 1/2 Knurl Bolts 8 1/2 Serrated Flange Nuts 1 Fish Wire (not shown) 4 Bed Plugs (not shown) Front Base Rail 5/8 Lock Nuts Rear Base Rail Frame Bracket Plates 5/8 x 1 3/4 Bolt & Flat Washer 1/2 flange Nuts 1/2 x 1 1/2 Knurled Bolts (inserted through access hole in frame)

Hijacker Underbox Mounting System 4.200 1999-2007 Chev and GMC 1500/2500 (classic style) 2001-2010 Chev and GMC 2500 HD and 3500 HD 2003-07 Chev and GMC 1500 HD (classic style) (For install in 6 ½ and 8 boxes only) UM401001 General Assembly and Install Instructions Hitch Assembly: Place the base rails on a flat level surface and insert and lock the side rail plates into the base rail holes as shown in the UM402001 instructions. Loosely bolt the saddle bracket (403PA) and the two cross braces to the side rails using the fasteners provided in the UM402001 carton. Tighten all the bolts. Unlock and remove the hitch assembly from the base rails and put to the side for later. Truck Bed Drilling Instructions: Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. The four 2 diameter holes that need to be drilled through the box are done by the following method: 1. Use the measurements shown on the drill hole measurement chart to mark out the four holes that will be drilled through the truck bed. 2. Start out by measuring the distance stated for the particular model of truck you are doing the installation on (refer to model on chart) from the end of the bottom of the truck bed (tailgate end) to a point on the left side of center of the bed and mark it. Do the same on the right side of center of the bed and mark it. Draw a line across the bed using these two marks as a reference. 3. Measure out and find the center of the truck bed and draw a line from the front to the rear of the bed. 4. Measure out 14 13/16 to either side of the middle centerline slightly ahead of the fender well and slightly behind the fender well. 5. Draw a line between these two points. Do the same on the other side. 6. Measure out (towards the cab) 13 1/2 from the points where the line that goes across the bed intersects with the two lines that are 14 13/16 off the center running the length of the bed. Mark these two points. 7. There should now be four spots marked out for drilling. Double check that the rear to hole marks are exactly the distance stated for the model of truck you are doing the installation on (refer to model on chart) from the end of the bed and that the front holes marks are exactly 13 1/2 forward of those marks. 8. Check the hole marks from side to side and make sure they are exactly 29 5/8 apart from each other.

9. Finally, check for square by measuring diagonally from opposite corners (drawing #1). The measurement should be the same both ways. It should measure 32 9/16. 10. After all the hole marks have been double checked for proper placement, use a center punch and hammer to mark out the spots for drilling. 11. Drill the holes using a 2 hole saw. De-bur the holes using a small file and apply some touch up paint to match color (not supplied). Base Rail Installation: Heat Shield Removal: Drawing # 1 On some models there will be a heat shield that is attached to the bottom of the truck box that will have to have a section of it removed to make clearance for the base rail(s). 1. If the shield is below the level of the top of the frame, the base rail will have room to span across from frame rail to frame rail. 2. If the heat shield is above the level of the top of the frame, the shield must be cut and removed before the base rails can be installed. 3. Cut the heat shield just rear of the box support cross member that is at the front of the wheel well of the truck (see drawing # 2). Remove the screws that hold the rear section of the heat shield in place. A # 25 Torx head driver or and/or a 10 mm wrench or socket will be required to remove these screws. 4. Remove the heat shield. Rear of truck Cab of truck Drawing # 2 Cut here Remove bolts Wheel well

Use one of the following two methods to install the base rails. Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. 1. A) Remove the mounting bolts that attach the box to the truck frame on one side only. Raise and block the box high enough so the base rails can be inserted (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Lower and bolt the box back to the frame. Position base rails under holes drilled in bed. OR B) Locate a spot on both sides of the box support cross members on either side of the truck and cut and bend up a 3 1/2 wide section of the sheet metal lip where the bed and the fender well of the box join (drawing # 4). Insert base rails (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Bend the sheet metal back down and position base rails under holes drilled in bed. Bend up Cut Drawing # 3 Drawing # 4 2. With base rails in position below the bed and the base rail holes centered under the holes that were drilled in the bed of the truck, position one of the 1/8 thick shims under each end of the base rails between them and the top of the frame. Drop a 5/8 x 1 1/2 bolt through the top of the end of the base rail and shim (drawing # 5). Re-install and lock the hitch assembly into the base rails from the topside of the box. Truck Bed Base Rail 1/8 Shim Frame Push bracket against frame when fastening to base rail. Drawing # 5

3. Measure and center the entire hitch assembly side to side and front to back so that it is as close to center of the holes in the bed. 4. Attach the frame brackets to the base rails with the portion of the frame bracket that is notched out towards the cab of the truck (see drawing # 6). Fasten with the 5/8 bolts that were inserted in the mounting holes and secure with a 5/8 flat washer and 5/8 lock nut. Notched out end towards cab Cab of truck Drawing # 6 5. Tighten the bolts to the base rails ensuring that the frame bracket is up against the truck frame. 6. Using the holes in the frame bracket plates as a guide, drill the frame in the four mounting holes on each frame bracket with a 1/2 or 33/64 drill bit. You may want to drill smaller pilot holes to make drilling easier. It is best to install a 1/2 x 1 1/2 bolt, washer, and lock nut after each hole is drilled to ensure there is no shifting of the hitch while drilling the next hole(s). 7. Tighten all bolts. 8. Re-install the rear wheels (if removed), double check all fasteners for tightness, and lower truck (if raised). 9. Unlock and lift the hitch assembly out of the box to make sure it can be removed and inserted with relative ease. If there was any shifting during installation that caused any binding, simply loosen the 4 bolts that attach the base rail to the frame brackets and realign the base rail and retighten. 10.Ensure the side rail locking pins are turned and secured in the locked position with the safety pins. Install the hitch head to the saddle bracket.

Drill Hole Measurement Chart Tailgate

UM401001 Parts List: 2 Base Rails (Part # UM401001B) 2 Frame Bracket Plates (Part # UM401001A) 4 1/8 Shims (Part # UM406C) 8 1/2 x 1 1/2 Bolts (Part # 104) 8 1/2 Flat Washers (Part # 105) 8 1/2 Lock Nuts (Part # 106) 4 5/8 x 1 1/2 Bolts (Part # UM416) 4 5/8 Flat Washers (Part # 418) 4 5/8 Lock Nuts (Part # 417) 4 Bed Plugs (not shown) (Part # UM407) 5/8 x 1 1/2 Bolt (UM416) 1/2 x 1 1/2 Bolts (104) 1/2 Flat Washers (105) Base Rails (UM401001B) 1/8 Shims (UM406C) 1/2 Lock Nuts (106) Frame Brackets (UM401001A) 5/8 Flat Washer (418) 5/8 Lock Nut (417)

Hijacker Underbox Mounting System 4.201 2011 Chev and GMC 2500HD and 3500 HD (For install in 6 ½ boxes only) FB202001 General Assembly and Install Instructions Hitch Assembly: 5. Place the base rails on a flat level surface and insert and lock the side rail plates into the base rail holes as shown in the UM402001 instructions. 6. Loosely bolt the saddle bracket (403PA) and the two cross braces to the side rails using the fasteners provided in the UM402001 carton. 7. Tighten all the bolts. 8. Unlock and remove the hitch assembly from the base rails and put to the side for later. Truck Bed Drilling Instructions: Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. The four 2 diameter holes that need to be drilled through the box are done by the following method: 12. Use the measurements shown on the drill hole measurement chart to mark out the four holes that will be drilled through the truck bed. 13. Start out by measuring the distance stated for the particular model of truck you are doing the installation on (refer to model on chart) from the end of the bottom of the truck bed (tailgate end) to a point on the left side of center of the bed and mark it. Do the same on the right side of center of the bed and mark it. Draw a line across the bed using these two marks as a reference. 14. Measure out and find the center of the truck bed and draw a line from the front to the rear of the bed. 15. Measure out 14 13/16 to either side of the middle centerline slightly ahead of the fender well and slightly behind the fender well. 16. Draw a line between these two points. Do the same on the other side. 17. Measure out (towards the cab) 13 1/2 from the points where the line that goes across the bed intersects with the two lines that are 14 13/16 off the center running the length of the bed. Mark these two points. 18. There should now be four spots marked out for drilling. Double check that the rear to hole marks are exactly the distance stated for the model of truck you are doing the installation on (refer to model on chart) from the end of the bed and that the front holes marks are exactly 13 1/2 forward of those marks. 19. Check the hole marks from side to side and make sure they are exactly 29 5/8 apart from each other. 20. Finally, check for square by measuring diagonally from opposite corners (drawing #1). The measurement should be the same both ways. It should measure 32 9/16. 21. After all the hole marks have been double checked for proper placement, use a center punch and hammer to mark out the spots for drilling.

22. Drill the holes using a 2 hole saw. De-bur the holes using a small file and apply some touch up paint to match colour (not supplied). Base Rail Installation: Heat Shield Removal: Drawing # 1 On some models there will be a heat shield that is attached to the bottom of the truck box that will have to have a section of it removed to make clearance for the base rail(s). 1. If the shield is below the level of the top of the frame, the base rail will have room to span across from frame rail to frame rail. 2. If the heat shield is above the level of the top of the frame, the shield must be cut and removed before the base rails can be installed. 3. Cut the heat shield just rear of the box support cross member that is at the front of the wheel well of the truck (see drawing # 2). Remove the screws that hold the rear section of the heat shield in place. A # 25 Torx head driver or and/or a 10 mm wrench or socket will be required to remove these screws. 4. Remove the heat shield. Rear of truck Cab of truck Drawing # 2 Cut here Remove bolts

Use one of the following two methods to install the base rails. Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. 12. A) Remove the mounting bolts that attach the box to the truck frame on one side only. Raise and block the box high enough so the base rails can be inserted (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Lower and bolt the box back to the frame. Position base rails under holes drilled in bed. OR B) Locate a spot on both sides of the box support cross members on either side of the truck and cut and bend up a 3 1/2 wide section of the sheet metal lip where the bed and the fender well of the box join (drawing # 4). Insert base rails (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Bend the sheet metal back down and position base rails under holes drilled in bed. Bend up Cut Drawing # 3 Drawing # 4 13. With base rails in position below the bed and the base rail holes centered under the holes that were drilled in the bed of the truck, position one of the 1/8 thick shims under each end of the base rails between them and the top of the frame. Drop a 5/8 x 1 1/2 bolt through the top of the end of the base rail and shim (drawing # 5). Re-install and lock the hitch assembly into the base rails from the topside of the box. Truck Bed Base Rail 1/8 Shim Frame Push bracket against frame when fastening to base rail. Drawing # 5

14. Measure and center the entire hitch assembly side to side and front to back so that it is as close to center of the holes in the bed. 15. Attach the frame brackets to the base rails. Fasten with the 5/8 bolts that were inserted in the mounting holes and secure with a 5/8 flat washer and 5/8 lock nut. 16. Tighten the bolts to the base rails ensuring that the frame bracket is up against the truck frame. 17. Install the 5/8 carriage bolts and bolt plates by fishing them through an access hole on the inside of the frame and fasten them to the outside of the frame brackets with the 5/8 flange nuts. See drawing on last page. 18. Tighten all bolts to 150 ft. lbs. torque. 19. Re-install the rear wheels (if removed), double check all fasteners for tightness, and lower truck (if raised). 20. Unlock and lift the hitch assembly out of the box to make sure it can be removed and inserted with relative ease. If there was any shifting during installation that caused any binding, simply loosen the 4 bolts that attach the base rail to the frame brackets and realign the base rail and retighten. 21. Ensure the side rail locking pins are turned and secured in the locked position with the safety pins. Install the hitch head to the saddle bracket.

Drill Hole Measurement Chart Tailgate

FB202001 Parts List: 2 Base Rails 2 Frame Bracket Plates 4 1/8 Shims 4 5/8 x 2 Carriage Bolts 4 5/8 Carriage Bolt Plates 4 5/8 x 1 1/2 Bolts 4 5/8 Flat Washers 4 5/8 Lock Nuts 4 5/8 Flange Nuts 4 Bed Plugs (not shown) (Part # UM407) 1 5/8 Fish Wire (not shown) Frame Bracket Base Rails (UM401001B) 5/8 x 1 1/2 Bolt 5/8 x 2 Carriage Bolts & 5/8 Carriage Bolt Plates 5/8 Flange Nuts 1/8 Shims (UM406C) 5/8 Flat Washer (418) 5/8 Lock Nut (417)

Hijacker Underbox Mounting System 4.202 2011 Chev and GMC 2500HD and 3500 HD (For install in 8 boxes only) FB202002 General Assembly and Install Instructions Hitch Assembly: 9. Place the base rails on a flat level surface and insert and lock the side rail plates into the base rail holes as shown in the UM402001 instructions. 10. Loosely bolt the saddle bracket (403PA) and the two cross braces to the side rails using the fasteners provided in the UM402001 carton. 11. Tighten all the bolts. 12. Unlock and remove the hitch assembly from the base rails and put to the side for later. Truck Bed Drilling Instructions: Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. The four 2 diameter holes that need to be drilled through the box are done by the following method: 23. Use the measurements shown on the drill hole measurement chart to mark out the four holes that will be drilled through the truck bed. 24. Start out by measuring the distance stated for the particular model of truck you are doing the installation on (refer to model on chart) from the end of the bottom of the truck bed (tailgate end) to a point on the left side of center of the bed and mark it. Do the same on the right side of center of the bed and mark it. Draw a line across the bed using these two marks as a reference. 25. Measure out and find the center of the truck bed and draw a line from the front to the rear of the bed. 26. Measure out 14 13/16 to either side of the middle centerline slightly ahead of the fender well and slightly behind the fender well. 27. Draw a line between these two points. Do the same on the other side. 28. Measure out (towards the cab) 13 1/2 from the points where the line that goes across the bed intersects with the two lines that are 14 13/16 off the center running the length of the bed. Mark these two points. 29. There should now be four spots marked out for drilling. Double check that the rear to hole marks are exactly the distance stated for the model of truck you are doing the installation on (refer to model on chart) from the end of the bed and that the front holes marks are exactly 13 1/2 forward of those marks. 30. Check the hole marks from side to side and make sure they are exactly 29 5/8 apart from each other. 31. Finally, check for square by measuring diagonally from opposite corners (drawing #1). The measurement should be the same both ways. It should measure 32 9/16. 32. After all the hole marks have been double checked for proper placement, use a center punch and hammer to mark out the spots for drilling.

33. Drill the holes using a 2 hole saw. De-bur the holes using a small file and apply some touch up paint to match colour (not supplied). Base Rail Installation: Heat Shield Removal: Drawing # 1 On some models there will be a heat shield that is attached to the bottom of the truck box that will have to have a section of it removed to make clearance for the base rail(s). 5. If the shield is below the level of the top of the frame, the base rail will have room to span across from frame rail to frame rail. 6. If the heat shield is above the level of the top of the frame, the shield must be cut and removed before the base rails can be installed. 7. Cut the heat shield just rear of the box support cross member that is at the front of the wheel well of the truck (see drawing # 2). Remove the screws that hold the rear section of the heat shield in place. A # 25 Torx head driver or and/or a 10 mm wrench or socket will be required to remove these screws. 8. Remove the heat shield. Rear of truck Cab of truck Drawing # 2 Cut here Remove bolts

Use one of the following two methods to install the base rails. Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. 22. A) Remove the mounting bolts that attach the box to the truck frame on one side only. Raise and block the box high enough so the base rails can be inserted (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Lower and bolt the box back to the frame. Position base rails under holes drilled in bed. OR B) Locate a spot on both sides of the box support cross members on either side of the truck and cut and bend up a 3 1/2 wide section of the sheet metal lip where the bed and the fender well of the box join (drawing # 4). Insert base rails (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Bend the sheet metal back down and position base rails under holes drilled in bed. Bend up Cut Drawing # 3 Drawing # 4 23. With base rails in position below the bed and the base rail holes centered under the holes that were drilled in the bed of the truck, position one of the 1/8 thick shims under each end of the base rails between them and the top of the frame. Drop a 5/8 x 1 1/2 bolt through the top of the end of the base rail and shim (drawing # 5). Re-install and lock the hitch assembly into the base rails from the topside of the box. Truck Bed Base Rail 1/8 Shim Frame Push bracket against frame when fastening to base rail. Drawing # 5

24. Measure and center the entire hitch assembly side to side and front to back so that it is as close to center of the holes in the bed. 25. Attach the frame brackets to the base rails. Fasten with the 5/8 bolts that were inserted in the mounting holes and secure with a 5/8 flat washer and 5/8 lock nut. 26. Tighten the bolts to the base rails ensuring that the frame bracket is up against the truck frame. 27. Install the 5/8 carriage bolts and bolt plates by fishing them through an access hole on the inside of the frame and fasten them to the outside of the frame brackets with the 5/8 flange nuts. See drawing on last page. 28. Tighten all bolts to 150 ft. lbs. torque. 29. Re-install the rear wheels (if removed), double check all fasteners for tightness, and lower truck (if raised). 30. Unlock and lift the hitch assembly out of the box to make sure it can be removed and inserted with relative ease. If there was any shifting during installation that caused any binding, simply loosen the 4 bolts that attach the base rail to the frame brackets and realign the base rail and retighten. 31. Ensure the side rail locking pins are turned and secured in the locked position with the safety pins. Install the hitch head to the saddle bracket.

Drill Hole Measurement Chart Tailgate

FB202002 Parts List: 2 Base Rails 2 Frame Bracket Plates 4 1/8 Shims 4 5/8 x 2 Carriage Bolts 4 5/8 Carriage Bolt Plates 4 5/8 x 1 1/2 Bolts 4 5/8 Flat Washers 4 5/8 Lock Nuts 4 5/8 Flange Nuts 4 Bed Plugs (not shown) (Part # UM407) 1 5/8 Fish Wire (not shown) Frame Bracket Base Rails (UM401001B) 5/8 x 1 1/2 Bolt 5/8 x 2 Carriage Bolts & 5/8 Carriage Bolt Plates 5/8 Flange Nuts 1/8 Shims (UM406C) 5/8 Flat Washer (418) 5/8 Lock Nut (417)

Hijacker Underbox Mounting System 4.300 2002-08 Dodge Ram 1500 & 2003-2011 Dodge Ram 2500 and 3500 Includes 4x2 and 4x4 models & MegaCab models 2007-2011 Chev Silverado & GMC Sierra 1500 Short Box (For install in 6 ½ and 8 boxes only) Hitch Assembly: UM401004 General Assembly and Install Instructions Place the base rails on a flat level surface and insert and lock the side rail plates into the base rail holes as shown in the UM402001 instructions. Loosely bolt the saddle bracket (403PA) and the two cross braces to the side rails using the fasteners provided in the UM402001 carton. Tighten all the bolts. Unlock and remove the hitch assembly from the base rails and put to the side for later. Truck Bed Drilling Instructions: Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. The four 2 diameter holes that need to be drilled through the box are done by the following method: 1. Use the measurements shown in drawing # 1 to mark out the four holes that will be drilled through the truck bed. 2. Start out by measuring from the end of the bottom of the truck bed (tailgate end) to a point on the left side of center of the bed and mark it. Do the same on the right side of center of the bed and mark it. Draw a line across the bed using these two marks as a reference. 3. Measure out and find the center of the truck bed and draw a line from the front to the rear of the bed. 4. Measure out 14 13/16 to either side of the middle centerline slightly ahead of the fender well and slightly behind the fender well. 5. Draw a line between these two points. Do the same on the other side. 6. Measure out (towards the cab) 13 1/2 from the points where the line that goes across the bed intersects with the two lines that are 14 13/16 off the center running the length of the bed. Mark these two points. 7. There should now be four spots marked out for drilling. Double check that the rear to hole marks are exactly (34 1/4 for short box and 36 1/4 for long box models) from the end of the bed and that the front holes marks are exactly 13 1/2 forward of those marks. 8. Check the hole marks from side to side and make sure they are exactly 29 5/8 apart from each other. 9. Finally, check for square by measuring diagonally from opposite corners (drawing # 2). The measurement should be the same both ways. It should measure 32 9/16. 10. After all the hole marks have been double checked for proper placement, use a center punch and hammer to mark out the spots for drilling. 11. Drill the holes using a 2 hole saw. De-bur the holes using a small file and apply some touch up paint to match color (not supplied).

Drawing # 1 Drawing # 2

Base Rail Installation: Use one of the following two methods to install the base rails. Note: It may make the install easier if the truck s rear end was lifted and blocked and/or remove the rear wheels to have more access for drilling of the frame. 1. A) Remove the mounting bolts that attach the box to the truck frame on one side only. Raise and block the box high enough so the base rails can be inserted (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Lower and bolt the box back to the frame. Position base rails under holes drilled in bed. OR B) Locate a spot between the box support cross members on either side of the truck and cut and bend up a 3 1/2 wide section of the sheet metal lip where the bed and the fender well of the box join (drawing # 4). Insert base rails (with locking pin holes up) and span across and rest on top of each side of the frame (drawing # 3). Bend the sheet metal back down and position base rails under holes drilled in bed. Bend up Cut Drawing # 3 Drawing # 4 2. With base rails in position below the bed and the base rail holes centered under the holes that were drilled in the bed of the truck, position one of the 3/8 thick shims under each end of the base rails between them and the top of the frame. Drop a 5/8 x 1 3/4 bolt through the top of the end of the base rail and shim (drawing # 5). Re-install and lock the hitch assembly into the base rails from the topside of the box. Truck Bed Base Rail 3/8 Shim Frame Push bracket against frame when fastening to base rail.

Drawing # 5 3. Measure and center the entire hitch assembly side to side and front to back so that it is as close to center of the holes in the bed. 4. Attach the frame brackets to the base rails with the 5/8 bolts that were inserted in the mounting holes and secure with a 5/8 lock washer and 5/8 hex nut. 5. Tighten the bolts to the base rails ensuring that the frame bracket is up against the truck frame. 6. Using the holes in the frame bracket plates as a guide, drill the frame in the four mounting holes on each frame bracket with a 1/2 drill bit. You may want to drill smaller pilot holes to make drilling easier. 7. Brackets will be bolted onto frame by fishing a 1/2 x 1 1/2 knurl bolt through frame with a fish wire and attach with a 1/2 flange nut on outside of bracket. There are access holes just behind the rear cross member. These can be used to fish the bolt through. 8. Tighten all bolts. 9. Re-install the rear wheels (if removed), double check all fasteners for tightness, and lower truck (if raised). 10.Unlock and lift the hitch assembly out of the box to make sure it can be removed and inserted with relative ease. If there was any shifting during installation that caused any binding, simply loosen the 4 bolts that attach the base rail to the frame brackets and realign the base rail and retighten. 11.Ensure the side rail locking pins are turned and secured in the locked position with the safety pins. Install the hitch head to the saddle bracket.

UM401004 Parts List: 2 Base Rails (Part # UM401001B) 4 Frame Bracket Plates (Part # UM401004A) 4 3/8 Shims (Part # UM406D) 8 1/2 x 1 1/2 Knurl Bolts (Part # 500) 8 1/2 Serrated Flange Nuts 4 5/8 x 1 3/4 Bolts (Part # 508) 4 5/8 Lock Washers 4 5/8 Hex Nuts 1 Fish Wire (not shown) (Part # BFW52) 4 Bed Plugs (not shown) (Part # UM407) 5/8 x 1 3/4 Bolt (508) 1/2 Flange Nuts 3/8 Shims (UM406D) Base Rails (UM401001B) Frame Brackets (UM401004A) 1/2 x 1 1/2 Knurled Bolts (500) 5/8 Lock Washer and 5/8 Hex Nut

Section 5 --- AutoSlide Hitch 58

24-AS-18 59

24-UAS-18 60

Hijacker AutoSlide Capture Plate 5 th Airborne Pin Box Application: e 61 1. Place capture plate up under pin box, inserting the king pin through the hole opening (drawing 1). 2. Once the hole clears the collar on the bottom of the king pin and is even with the 2 diameter middle, pull the capture plate towards the front (drawing 2) so bent lip can clear front bend of pin box plate (drawing 3). 3. Push capture plate back to clear top shoulder of king pin and press up flush against the trailer king pin plate (drawing 4). 4. Fasten to king pin with 3/8 bolts and nuts using existing holes in king pin skid plate at rear. Push bolts with a washer up through the capture plate and have the nut and washer on the inside portion of the king pin box. Tighten securely (drawing 5). 1 2 3 4 5

AUTOSLIDE ADAPTER FOR MOR/RYDE INSTALL INSTRUCTIONS 62 1) Remove four 9/16-12 bolts 2) Push restraining rods toward 3) Slide spacer blocks in to with 13/16 socket. center of box. channel. 4) Install bolt through hole. 5) Install and tighten nut (self 6) Slide Hijacker skid pad locker) x 4 (making sure wedge is to rear of box) into place. 7) Put plate in location using 8) Align opposite corners to 9) Align all four bolts before two 9/16-12 bolts opposite restraining rods. tightening. corners to hold plate. 10) Tighten all four bolts. 11) Completed installation. Torque to 85 ft.-lbs.