Remove Label Yellow s Cyan s Light s Light Cyan s Remove Label Hewlett Packard Cartridges Refill instructions for the HP Cartridges: 22, 27, 28, 56, 57 & 58. DeskJet: 220, 310, 450, 450nt, 450ci, 450cbi, 3320, 3325, 3420, 3425, 3450, 3520, 3550, 3600, 3650, 3740, 3743, 3744, 3745, 3840, 3843, 3845, 5100, 5150, 5550, 5551, 5552, 5600, 5650, 5652, 5850, 9600, 9650, 9670, 9680. OfficeJet: 2455, 4110, 4200, 5500, 5508, 5510, 5515, 6100, 6110, 6110xi, PSC: 1110, 1200, 1205, 1209, 1210, 1215, 1219, 1300, 1310, 1311, 1315, 1317, 1350, 1355, 2105, 2110, 2110v, 2110xi, 2115, 2170, 2175, 2175v,2175xi, 2179i, 2210, 2400, 2405, 2410, 2500, Photosmart: 100, 130, 140, 145, 230, 240, 245, 4700, 7150, 7200, 7260, 7350, 7400, 7450, 7550, 7600, 7660, 7700, 7760, 7762, 7900, 7960, P230, P245, P7450, P7550, 7650gp, P7755, P7660, P7345. COLOUR & PHOTO CARTRIDGE 1. The filler holes are located under the coloured top of the cartridge 2. Peel label back on top of cartridge. 3. Assemble syringe and steel filling tube and fill with appropriate colour ink. 4. Insert the steel filling tube into the appropriate filling holes. (See diagram above). Push down into centre of the sponge. IMPORTANT: Cartridge contains a sponge and a slight resistant may be felt. 5. SLOWLY Inject ink. When ink overflows from filling hole or starts to leak from print heads cartridge is full. Stop injecting immediately. Blot printer heads with tissue before continuing to fill next colour. IMPORTANT: Clean syringe with water and dry before refilling next colour. 6. After refilling replace label back over hole and seal with adhesive tape. 7. Leave the cartridge to stand overnight on non-absorbent surface this will ensure no IMPORTANT: DO NOT LEAVE ON TISSUE. 8. Install cartridge and run a priming cycle. PLEASE NOTE: The ink indicator level may need to be turned off. Check your HP instructions manual for details. 102
HEWLETT PACKARD Hewlett Packard Colour Copier: 110, 120, 140, 145, 150, 155, 160, 170, 180, 190, 210, 260, 270, 280, 290, Copyjet M. DesignJet: 220, 230, 250c, 330, 330d. 350c, 430c, 450c, 455ca, 488ca, 700, 750c, 750c+, 755cm, 1050, 1055, 2000cp, 2500cp, 2800cp Wide, 3000cp Wide, 3500cp, 3800cp Wide. DeskJet: 700, 710, 710c, 712, 720, 720c, 722c, 810, 810c, 812c, 815c, 820c, 820cse, 820cxi,, 820csi, 830c, 832c, 840c, 841c, 842c, 843c, 845c, 850c, 855c, 855cse, 855csi, 855cxi, 865cse, 870cse, 870cxi, 880c, 882c, 890c, 895c, 895cxi, 920c, 930c, 932c, 934c, 935c, 940c, 950c, 952c, 955c, 957c, 960cse, 960cxi, 970cse, 970cxi, 980cxi, 990, 990cxi, 995c, 1000, 1000c, 1000cse, 1000cxi, 1100c, 1100cse, 1100cxi, 1120c, 1120cse, 1200c, 1200cps, 1220c, 1220cse, 1220cps, 1220cxi, 1280, 1600c, 1600m, 1600n, 3810, 3816, 3820, 3822, 6122, 6127, 9300.OfficeJet: G55, G55xi, G85, G85xi, G95, K60, K80, R40, R45, R60, R65, R80, T45, T65, V30, V40, V45, 1170, 1175, 5105, 5110. OfficeJet Pro: 1150c, 1150cse, 1170c, 1170cse, 1175c, 1175cse. Photosmart: 1115, 1215, 1215vm, 1218, 1218xi, 1315, P1000, P1100, P1100xi, P1115, P1215, P1218, P1315. PSC: 500, 500si, 700, 750, 750xi, 950. Professional series: 825c, 930c, 932c, 935c, 950c, 952c, 955c, 960c, 970c, 990c, 995c, 1000c, 1120c, 1220c, 1600c, 3820, 6122, 6127. Digital Colour Copiers: 310. Fax: 1220, 1220xi, 1230. 1. Turn the cartridge upside down. Remove the plastic film that seals the filling hole and push ball bearing into the cartridge using an old ballpoint pen. IMPORTANT: DO NOT use the steel filling tube to push in the ball bearing. 2. Assemble the syringe and steel filling tube and fill with ink. 3. SLOWLY inject ink into the filling hole, keeping the syringe as upright as possible. Fill the cartridge until ink appears around the filling hole and then pull back on the syringe and withdraw just 2-3mls of ink. 4. Gently squeeze the sides of the cartridge whilst inserting the rubber plug into the filling hole. Secure the plug with strong adhesive tape. This seal MUST be airtight, if not cartridge will leak. 5. Turn the cartridge the correct way up and place it on an old saucer or dish. Ink may initially seep from the print heads whilst the vacuum within the cartridges is reestablished. This is quite normal. Allow up to an hour for the seepage to stop and then blot the print heads clean with kitchen roll. Check the seepage has stopped before replacing the cartridge in the printer. IMPORTANT: DO NOT LEAVE THE CARTRIDGE STANDING ON TISSUE. 6. Clean the syringe with water and dry for future use. 7. Install cartridge into printer and run a cleaning cycle as per printer instructions. IMPORTANT: For best results, refill whilst ink still remains in cartridge. Empty cartridges should be refilled immediately. 103
Yellow IMPORTANT: DO NOT follow the implied filling sequence shown on the side of the colour cartridge. Follow the colour filling details in our instructions. (See filling diagram). Cyan HEWLETT PACKARD Hewlett Packard Colour Copier: 160, 170, 180, 190, 260, 270, 280, 290. DeskJet: 700, 710, 710c, 712, 720, 720c, 722c, 810, 810c, 812c, 815c, 820c, 820cse, 820cxi,, 820csi, 830c, 832c, 840c, 841c, 842c, 843c, 845c, 850c, 855c, 855cse, 855csi, 855cxi, 865cse, 870cse, 870cxi, 880c, 882c, 890c, 895c, 920c, 930c, 932c, 934c, 935c, 940c, 950c, 952c, 955c, 957c, 960cse, 960cxi, 970cse, 970cxi, 980cxi, 990, 990cxi, 995c, 1000, 1000c, 1000cse, 1000cxi, 1100c, 1100cse, 1100cxi, 1120c, 1120cse, 1200c, 120cps, 1220cse, 1220cxi, 1280, 3810, 3816, 3820, 3822, 6122, 6127, 9300.OfficeJet: G55, G55xi, G85, G85xi, G95, K60, K80, R40, R45, R60, R65, R80, T45, T65, V30, V40, V45, 1170, 1175, 5105, 5110. OfficeJet Pro: 1150c, 1150cse, 1170c, 1170cse, 1175c, 1175cse. Photosmart: 1115, 1215, 1215vm, 1218, 1218xi, 1315, P1000, P1100, P1100xi, P1115, P1215, P1218, P1315. PSC: 500, 500si, 700, 750, 750xi, 950. Professional Series: 825c, 930c, 932c, 935c, 950c, 952c, 955c, 960c, 970c, 990c, 995c, 1000c, 1120c, 1220c, 1600c, 3820, 6122, 6127. Digital Colour Copier: 310. Fax: 1220, 1220xi, 1230. 1. The filling holes are located on top of the cartridge and are sealed with small-vented plugs. Push these plugs into the cartridge using an old ballpoint pen. Do not use the steel filling tube for this purpose. 2. Assemble the syringe and steel filling tube and fill with the appropriate colour ink. 3. Insert the steel filling tube into the appropriate filler hole, following the details in the diagram above. Push steel filling tube downwards into centre of the cartridge. IMPORTANT: The cartridge contains a sponge and a slight resistance may be felt. 4. SLOWLY inject ink. Blot the print heads with tissue to remove any excess ink before continuing to refill next colour. IMPORTANT: Clean syringe with water and dry before refilling next colour. 5. Leave cartridge to stand overnight on a protective, non-absorbent surface to ensure no leakage and to give the ink time to fully saturate the sponge. IMPORTANT: DO NOT LEAVE ON TISSUE. 6. Install the cartridge in the printer and run a cleaning cycle as per printer instructions. IMPORTANT: For best results, refill whilst ink still remains in cartridge. Empty cartridges should be refilled immediately. 104
BLACK HP 338 CARTRIDGE 1. Peel back label to locate filler hole (See Diagram) 2. Assemble syringe and steel filling tube and fill with black ink 3. Insert steel filling tube into the appropriate filling hole and push into the centre of the sponge. Making sure the filling tube is straight and not at an angle. 4. SLOWLY inject ink until slight leakage appears from the filling hole. 5. After refilling place label back over filling hole. 6. Leave the cartridge to stand overnight on protective non-absorbent surface this will ensure no 7. Install cartridge and run a cleaning cycle. IMPORTANT: For best results, refill whilst ink still remains in the cartridge. Empty cartridges left for more than a week do not always give a successful re-fill. 105
Filling hole BLACK HP 339 CARTRIDGE 1. Peel back label to locate filler hole (See Diagram) 2. Assemble syringe and steel filling tube and fill with black ink 3. Insert steel filling tube into the appropriate filling hole and push into the centre of the sponge. Making sure the filling tube is straight and not at an angle. 4. SLOWLY inject ink until slight leakage appears from the filling hole. 5. After refilling place label back over filling hole. 6. Leave the cartridge to stand overnight on protective non-absorbent surface this will ensure no 7. Install cartridge and run a cleaning cycle. IMPORTANT: For best results, refill whilst ink still remains in the cartridge. Empty cartridges left for more than a week do not always give a successful re-fill. 106