3mA TinyPower TM LDO Features Output voltage ranges: Fixed range of 1.8V 2.5V 2.7V 3.V 3.3V 5.V type. Highly accuracy: 2% Low voltage drop: 24mV (typ. V OUT =5.V at 3mA Maximum Input Voltage: 8V Guaranteed output current: 3mA Low quiescent current: 4A (typ. Current limiting Over-temperature shutdown SOT23 SOT23-5 SOT89 TO92 Packages Applications Portable electronics PC peripherals Wireless devices Battery powered devices Cordless phones Electronic scales General Description The HT72XX series of positive linear regulators features low quiescent current (4A typ. with low dropout voltage making them ideal for battery applications. The space-saving SOT23 package is attractive for Pocket and Hand Held applications. The devices are capable of supplying 3mA of output current continuously. They are available with several fixed output voltages ranging from 1.8V to 5.V. Although designed primarily as fixed voltage regulators these devices can be used with external components to obtain variable voltages and currents. These rugged devices have Thermal Shutdown and Current Limiting to prevent device failure under the Worst of operating conditions. Selection Table Part No. Output Voltage Tolerance Package Marking HT7218 1.8V HT7225 2.5V HT7227 2.7V HT723 3.V HT7233 3.3V 2% SOT23 SOT23-5 SOT89 TO92 72XX# (for SOT23 72XX# (for SOT23-5 HT72XX# (for SOT89 HT72XX (for TO92 HT725 5.V Note: XX stands for output voltages. For lead free devices TO92 package will add a # mark at the end of the date code whereas SOT89 & SOT23 SOT23-5 packages will add a # mark at the end of the marking. Rev. 1.2 1 September 3 28
Block Diagram 8 1 L A H? K H H A J 5 D K J @ M 6 D A H = 5 D K J @ M 8 7 6-4 2 8 H A B 4 / Pin Assignment 5 6! 5 6! # 5 6 & ' 6 ' 8 1 8 7 6 6 % : :. H J 8 E A M 6 % : : 6 F 8 E A M % : : 6 F 8 E A M % : : 6 F 8 E A M / 8 1 8 7 6 / 8 7 6 8 1 / - / 8 1 8 7 6 * J J 8 E A M / 8 7 6 8 1 / - / 8 1 8 7 6 / 8 1 8 7 6 Pin Description Pin No. SOT23 SOT23-5 SOT89 TO92 Pin Name Description 3 CE Chip enable pin high enable 2 5 3 3 VOUT Output pin 3 1 2 2 VIN Input pin 1 2 1 1 GND Ground pin 4 NC No connection Absolute Maximum Ratings* Maximum Supply Voltage... up to 8.5V Operating Temperature...4C to85c Storage Temperature...5C to125c Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. * Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional but do not guarantee specific performance limits. The guaranteed specifications apply only for the test conditions listed. Rev. 1.2 2 September 3 28
Thermal Information Symbol Parameter Package Max. Unit JA P D Thermal Resistance (Junction to Ambient (Assume no ambient airflow no heat sink Power Dissipation SOT23 667 C/W SOT23-5 5 C/W SOT89 2 C/W TO92 2 C/W SOT23.15 W SOT23-5.2 W SOT89.5 W TO92.5 W Note: P D is measured at Ta= 25C Electrical Characteristics T j =25C V IN =V OUT 1.V I O =1mA unless otherwise specified Symbol Parameter Test Conditions Min. Typ. Max. Unit V IN Input Voltage 8 V V OUT Output Voltage Tolerance 2 2 % I SS Quiescent Current I O =ma V CE =V IN 4 7 A V LOAD Load Regulation (Note1 1mAI OUT 3mA.4.8 %/ma V DROP Dropout Voltage (Note2 V OUT =2% I OUT =3mA V O 1.8V 8 12 2.5VV O 2.7V 35 4 3.VV O 5.V 24 3 V LINE Line Regulation V OUT 1.VV IN 8.V.2.3 %/V I LIM Current Limit (Note3 V OUT =1% 3 ma V IH CE Input High Threshold V OUT 1VV IN 8V 2. V V IL CE Input Low Threshold V OUT 1VV IN 8V.8 V I SD Shutdown Current CE input voltage.8v.5 1 A mv 8 7 6 6 = Note: Temperature Coefficient 4C<Ta<85C.8 mv/c 1. Load regulation is measured at a constant junction temperature using pulse testing with a low ON time and is guaranteed up to the maximum power dissipation. Power dissipation is determined by the input/output differential voltage and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. The maximum allowable power dissipation at any ambient temperature is P D =(T J(MAX Ta / JA. 2. Dropout voltage is defined as the input voltage minus the output voltage that produces a 2% change in the output voltage from the value at V IN =V OUT 1V with a fixed load. 3. Current limit is measured by pulsing for a short time. Rev. 1.2 3 September 3 28
Application Circuits Basic Circuits 8 1 8 1 6 % : : 8 7 6 8 7 6 5 A H E A I. /. 5 E C A F E J / 8 1 8 1 6 % : : 8 7 6 8 7 6-5 A H E A I. /. 5 E C A F E J / Typical Application Circuits High output current positive voltage regulator 6 H 1 8 1 4 8 1 6 % : : 8 7 6 8 7 6 5 A H E A I 14 - / 1. /. 5 E C A F E J / 8 * - 4 1 14 - / > 1 1 4 1- / Rev. 1.2 4 September 3 28
Increased Output voltage Circuit 8 1. 8 1 8 7 6 8 7 6 6 % : : 5 A H E A I 15 5 /. 8 : : 4 4 5 E C A F E J / V = V (1 R2 R1 I OUT XX SS R2 Dual Supply Circuit 1 8 1 1 8 1 6 % : : 5 A H E A I / 8 7 6 8 : :!. 8 7 6. 8 1 6 % : : 5 A H E A I / 8 7 6. 4 8 : : 8 7 6 5 E C A F E J / V = V V OUT1 XX2 XX1 V OUT2 = V XX2 Tracking Voltage Regulator 8 1 8 1 6 % : : 8 7 6 8 7 6 5 A H E A I. / 5 E C A F E J /. 4 4 * 8 1 8 -V = V x R O OUT R B A Rev. 1.2 5 September 3 28
Package Information 3-pin SOT23 Outline Dimensions - A G > Symbol Dimensions in mm Min. Nom. Max. A 1. 1.3 A1.1 A2.7.9 b.35.5 C.1.25 D 2.7 3.1 E 1.4 1.8 e 1.9 H 2.6 3. L.37 1 9 Rev. 1.2 6 September 3 28
5-pin SOT23-5 Outline Dimensions - A G > Symbol Dimensions in mm Min. Nom. Max. A 1. 1.3 A1.1 A2.7.9 b.35.5 C.1.25 D 2.7 3.1 E 1.4 1.8 e 1.9 H 2.6 3. L.37 1 9 Rev. 1.2 7 September 3 28
3-pin SOT89 Outline Dimensions * 1 -. / Symbol Dimensions in mil Min. Nom. Max. A 173 181 B 59 72 C 9 12 D 35 47 E 155 167 F 14 19 G 17 22 H 59 I 55 63 J 14 17 Rev. 1.2 8 September 3 28
3-pin TO92 Outline Dimensions * -. / Symbol Dimensions in mil Min. Nom. Max. A 17 2 B 17 2 C 5 D 11 2 E 9 11 F 45 55 G 45 65 H 13 16 I 8 18 4 6 Rev. 1.2 9 September 3 28
Product Tape and Reel Specifications Reel Dimensions 6 * 6 SOT23 SOT23-5 Symbol Description Dimensions in mm A Reel Outer Diameter 178.1. B Reel Inner Diameter 62.1. C Spindle Hole Diameter 13..2 D Key Slit Width 2.5.25 T1 Space Between Flange 8.4 1.5/-. T2 Reel Thickness 11.4 1.5/-. SOT89 Symbol Description Dimensions in mm A Reel Outer Diameter 18.1. B Reel Inner Diameter 62.1.5 C Spindle Hole Diameter 12.75.15/-. D Key Slit Width 1.9.15 T1 Space Between Flange 12.4.2/-. T2 Reel Thickness 17../-.4 Rev. 1.2 1 September 3 28
3-pin TO92 Reel Dimensions (Unit: mm 2 =? = C A 7 F. = J 5 E @ A 7 F! 2 =? = C A 7 F. = J 5 E @ A M # & "! & &! $ Rev. 1.2 11 September 3 28
Carrier Tape Dimensions 2 2 J -. 9 * 2 4 A A A 1 = H E C SOT23 SOT23-5 Symbol Description Dimensions in mm W Carrier Tape Width 8..3 P Cavity Pitch 4..1 E Perforation Position 1.75.1 F Cavity to Perforation (Width Direction 3.5.5 D Perforation Diameter 1.5.1/-. D1 Cavity Hole Diameter 1.5.1/-. P Perforation Pitch 4..1 P1 Cavity to Perforation (Length Direction 2..5 A Cavity Length 3.15.1 B Cavity Width 3.2.1 K Cavity Depth 1.4.1 t Carrier Tape Thickness.2.3 C Cover Tape Width 5.3.1 SOT89 Symbol Description Dimensions in mm W Carrier Tape Width 12..3/-.1 P Cavity Pitch 8..1 E Perforation Position 1.75.1 F Cavity to Perforation (Width Direction 5.5.5 D Perforation Diameter 1.5.1/-. D1 Cavity Hole Diameter 1.5.1/-. P Perforation Pitch 4..1 P1 Cavity to Perforation (Length Direction 2..1 A Cavity Length 4.8.1 B Cavity Width 4.5.1 K Cavity Depth 1.8.1 t Carrier Tape Thickness.3.13 C Cover Tape Width 9.3.1 Rev. 1.2 12 September 3 28
3-pin TO92 Carrier Tape Dimensions 2 D 9 9 9 J 9 2.. 2 TO92 Symbol Description Dimensions in mm I1 Taped Lead Length (2.5 P Component Pitch 12.71. P Perforation Pitch 12.7.3 P 2 Component to Perforation (Length Direction 6.35.4 F 1 Lead Spread 2.5.4/-.1 F 2 Lead Spread 2.5.4/-.1 h Component Alignment..1 W Carrier Tape Width 18. 1./-.5 W Hold-down Tape Width 6..5 W 1 Perforation Position 9..5 W 2 Hold-down Tape Position (.5 H Lead Clinch Height 16..5 H 1 Component Height Less than 24.7 D Perforation Diameter 4..2 t Taped Lead Thickness.7.2 H Component Base Height 19..5 Note: Thickness less than.38.5mm~.5mm P Accumulated pitch tolerance: 1mm/2pitches. ( Bracketed figures are for consultation only Rev. 1.2 13 September 3 28