Thank you for your purchase. lease follow the instructions below for correct assembly. D I J V W X Y Z bolt x4 nut x4 x6 x10 dowel x16 locking nut x0 bolt x0 x0 shelf plug x8 handle x safety strap x1 x1 wall anchor x1 Wall trap wall x1 washer x L M N O x1 slide rail x slide rail x slide rail x slide rail x wedge x1 wheel x4 wheel x4 x1 ardware upplied hillips & lathead drivers required or quicker assembly, we recommend the use of a power drill on a low-speed setting. WNIN: ny furniture that is not anchored to a wall has the potential to tip over in certain circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake. ccordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device provided should fit most wall types, but please note that different wall materials may require different fixing devices from those supplied. 1
1 D D 9 Drawers x N O J 10 D D 1 D D 11 1 J J ttach 1x handle (J) to each panel [9] and [10] as shown, and secure with 4x s (D). ttach x wheels () and () to each panel [9] and [10] as shown, and secure with x s (). Tighten with a driver. ttach 1x slide rail (N) to panel [1] and 1x slide rail (O) to panel [1] using 4x s (). Insert 4x bolts () into panel [11]. ttach 1x handle (J) to panel [11] and secure with x s (D). Tighten all with a driver epeat this step to assemble the other two drawers.
4 Drawers x 1 1 1 L L L 11 14 M M M ttach panels [1] and [1] to panel [11] with 4x locking nuts (). lide panel [1] between the grooves of side panels [1] and [1] to form the drawer base. ttach panel [14] and secure with 4x s (). Tighten with a driver. epeat this step to assemble the other two drawers. ttach x slide rails (L) to panel [] and x slide rails (M) to panel [] and secure with 18x s (). Tighten with a driver.
6 ttach 8x bolts () to panel [1]. ttach panels [], [], [4] and [] to panel [1] using 8x dowels () and secure with 8x locking nuts (). Tighten with a flathead driver. 1 4 1 4
Jolt Wardrobe MLY INTUTION 7 8 7 7 7 4 8 4 lide x panels [7] down the grooves between panels [] and [], panels [] and [4], and panels [4] and []. ttach panel [8] to the main unit using 8x dowels () and secure with 8x s (). Tighten with a driver.
9 10 6 6 nsure slot in nut is facing incoming bolt. 16 17 8 17 16 ttach panels [16] and [17] together as shown using 4x nuts () and 4x bolts ().Tighten with a driver. ttach the legs to panel [8] using 1x s () and tighten with a driver. ttach leg support [6] and tighten as shown. 6
11 1 I I 18 18 Insert 8x shelf plugs (I) into the cabinet to hold panels [18] level on top of them. Insert the three drawers, ensuring they slide easily along the rails. 7
1 14 10 9 back O Note: If the door is not sliding smoothly or sitting straight, there is a in the middle of the wheel on the bottom of each door that can be tightened/loosened until the door is sitting properly. ttach door panels [9] and [10] as shown, starting with the back door first and then the front door. ress the clip down on the back of the door to assemble the door. ush the clip back up to lock into place. ttach 1x wedges () into each corner of the back panels and secure with 1x s (). Tighten with a driver. 8
1 16 strap washer V wall plug washer Z X Z Y W W Z V Once assembled lift the cabinet into the desired location, do not drag. ttach the safety strap (V) to the underside of the top back edge of the unit using 1x washer (Z) and 1x (Y). Tighten with a driver. ttach the other end of the safety strap (V) to the wall with 1x washer (Z), 1x wall plug (X) and 1x (Y) and tighten with a driver. You re done, enjoy! 9