Installation Instructions for the Multi SmartBox Please read thoroughly before beginning the installation. Notes a) Proficient DIY skills are assumed. b) It is assumed a suitably qualified electrical installer will make all electrical connections. c) The Multi SmartBox is designed for anchoring to a floor. A level and firm floor, such as concrete or flags, is assumed. It is recommended that the Multi unit is additionally anchored to a solid wall for extra secure reinforcement. d) Please consult with your local hardware store in the event your property requires alternative fixing parts to those supplied with your Multi SmartBox. Note that the supplier or manufacturer of your Multi SmartBox will not be responsible for any damages carried out by this installation. e) Anchor Holes have not been drilled in the Multi SmartBox so as to allow the purchaser flexibility in how to do the installation. Tools required Power Screw Driver recommended 8mm Metal Drill Metal 8mm Masonry Drill Bit Extended 8mm Drill Bit sufficiently long to drill through the property wall Adjustable Spanner Marking pencil Parts supplied 4 Adjustable feet 2 Floor Anchor Bolts, 8mm diameter, 120mm long 4 Wall Anchor Bolts, 8mm diameter, 80mm long Antenna +12V Power Charger Unit
1. Preparation for Floor Installation Turn the Multi SmartBox on its side and drill 2 holes in its base (8mm Metal Drill Bit) to coincide with the 2 predrilled floor holes in the support bars. Figure 1. Position the unit at its desired location. Ensure easy access is allowed for and that fully open doors do not impact on the location surrounds. Adjust the feet to ensure the unit is level. Mark through the 2 drilled floor holes to corresponding anchor hole positions on the concrete floor. Figure 2. Remove the unit and drill the 2 ground anchor holes in the concrete ground using the 8mm Masonry Drill bit to a depth of 100mm. 2. Preparation for Wall Installation Mark the positions for 4 holes in the unit s back and drill out using the 8mm Metal Drill Bit. Figure 3. Reposition the unit and insert the 2 floor anchor bolts. Ensure it is level and partially tighten the floor bolts. Mark through the 4 wall mount holes to corresponding positions in the solid wall. Remove the unit and drill out the wall holes using the 8mm Masonry Drill Bit to a depth of 80mm. 3. Antenna Connection and +12V Power Charger Connection For the purposes of these instructions, it is assumed that the Power Charger will be plugged into an electrical socket located within a property and that its lead be thread through an exterior wall to the SmartBox. Other arrangements could apply. For example, a +12V connection could be taken from an electric gate power supply, etc. Locate the Antenna and Power Charger Lead Holes at the back of the SmartBox. (Alternatively, locate the Lead Holes underneath the SmartBox). Figures 4a, 4b. Remove the SmartBox Internal Panel by undoing the 4 holding screws. Figure 5. A Control Module is attached on the inner side of the Internal Panel. This Control Module has mating connectors for the Antenna and Power Charger Leads. Antenna
Locate the Antenna connector on the Control Module. Thread the Antenna lead through the SmartBox Lead Hole and connect it to the Control Module's Antenna connector. The Antenna has a magnetic base. Attach the Antenna to a suitable position on the SmartBox. Power Charger Reposition the SmartBox and mark through the Charger lead hole to a corresponding hole on the solid wall. Remove the SmartBox and drill out the wall hole using the extended 8mm Masonry Drill Bit. Thread the Power Charger lead through the wall. Ensure the Power Charger is not plugged in. Reposition the SmartBox. Thread the Charger lead through the SmartBox Lead Hole and connect it to the Control Module's Charger connector. Replace the Internal Panel and reconnect the 4 holding screws. 4. Installation It is assumed that the Antenna and Power Charger Leads are connected. See 3 above. Reposition the Multi SmartBox. Insert the 2 floor 120mm anchor bolts for positioning. Partially screw in. Insert the 4 wall 80mm anchor bolts. Partially screw in. Gradually tighten all bolts until all are securely fixed to their anchor points.
Figure 1 Figure 2 Figure 3
Figure 4a Figure 4b Figure 5