LCD PDWM 225 PDWM 250 PDWM 275
.FOREWORD...2 2.INTRODUCTION...2 3.SYSTEM FETURES...2 4.SYSTEM TYPE...2 5.EIGHT CHNNEL RECEIVER FETURES...3 6.TRNSMITTER FUNCTION & FETURES...4-5 7.TRNSMITTER TTERY INSTLLTION...6.ODYPCK TRNSMITTER CONNECTION...7 9.SYSTEM CONNECTIONS... 0.TROULE SHOOTING...9 6.SPECIFICTIONS...9-0 2.OPTIONL CCESSORIES...0 5 6 2
EIGHT CHNNEL RECEIVER FETURES. Grille: Protects the cartridge and help reducing the breath sounds and wind 2 4 3 CH6 CH5 noise. 2. LCD Information Display: Show the 5 CH7 transmitter frequency channel ect. CH PLL 3.Down Function utton: Sets channel data. CH2 CH CH4 CH3 4.Up Function utton: Sets channel data. 6 EIGHT CHNNEL PROFESSIONL WIRELESSRECEIVER 5.Power and udio Mute Switch. 2 3 4 5 2 3 4 5 2 3 4 5 2 3 4 6.attery Cover: Open it to install the battery. 5 Front Panel NTENN CH - 9 0 0 0 CH 5- CH -4 0 0 0 0 CH - 0 2 NTENN 4 5 2 Rear Panel.Power utton: Power ON/OFF the receiver. 2.Down Function utton: Sets channel data. 3."RF" signal Indicator:It glows when the Receiver receive RF signal from Transmitter. 4.LCD Information Display: Show the receiver frequency channel ect. 5.Volume Knob: djust the volume output of receiver. 6.Up Function utton: Sets channel data. 7."F"udio Level Indicator: Indicate the wireless system audio signal level..ntenna. 9.Power switch of CH5-: When switch to "ON" position, it means CH5 to CH is on, all channcels from to is on for working. When switch to "OFF" position, it means CH5 to CH is off, only CH to CH4 is on for working. 0.XLR alanced Output Jack: Connect the audio cable from this jack to the input port of amplifier, mixer../4" udio Output Jack: Connect the audio cable from this jack to the input port of amplifier, mixer.(ch-4 or CH5-) 2. Power Jack: Connect the C/DC adapter to receiver. 3 3 6 DISPLY ELT-PCK TRNSMITTER 7 9 0. Power and udio Mute Switch. 2. ntenna: Transmit the RF signal of transmitter. 3. elt Clip: ttach the transmitter to the belt. 4. udio Input Jack: it is suitable for lavalier system/headset system. 5. Low attery Indicator: Red light glows when it is lack of power and should renew the battery. 6. LCD Information Display: Show the transmitter frequency channel ect. 7. Gain djusting Volume: djust the transmitter audio input gain..state Setting Switch: Set the using state of lavalier system(l)/headset system(h) /guitar system(g). 9.Up Function utton: Sets channel data. 0.Down Function utton: Sets channel data. 4
TRNSMITTER TTERY INSTLLTION. attery Installation of Handheld Microphone: Open the battery cover, Insert the supplied batteries into battery jar in polarity and cover the battery ODYPCK TRNSMITTER CONNECTION. Lavalier Microphone Connection: Connect the connecter of supplied lavalier microphone to the connecting jack of transmitter (shown as below) Set the transmitter work state in wireless lavalier system(l). 2. Headset Microphone Connection: Connect the connecter of supplied headset microphone to the connecting jack of transmitter(shown as below) Set the transmitter work state in wireless headset system(h). Rotate counterclockwise to open. 2. attery Installation of odypack Transmitter:Push open the battery cover, Insert the supplied batteries into battery jar in polarity and close the battery cover. DISPLY ELT-PCK TRNSMITTER Push down to open. OPERTING INSTRUCTIONS. Receiver Operation Power on receiver, press two "UP" buttons of module 2 and 3 together for second to enter the adjustment, when the LCD displays "UnLOC", it is under "Normal Operation". When the LCD displays "LOC", it is under "Locking Operation". a. Normal Operation -Press and hold "UP"/"DOWN" button, release the button once the CH number begins to flash -When it is flashing, continue to press "UP"/"DOWN" button to increase /decrease the channel orderly, select the desired channel -The selected channel will be save automatically without any action for 5 seconds. -Please refer to the following list for showing the adjusting channels. 5 6
NTENN NTENN CH - NTENN CH - CH - CH 5- CH -4 CH 5- CH -4 CH 5- CH -4 CH - CH - NTENN CH - NTENN NTENN b. Locking Operation -Press and hold "UP"/"DOWN" button, release the button once the CH number begins to flash -When it is flashing, continue to press "UP"/"DOWN"button to increase /decrease the channel orderly, select the desired channel -Once finish the channel adjustment of any one module, the channels of other seven modules will be changed automatically without any action to select the channels under same group. -The channels will be save automatically for using without any action for 5 seconds. -Please refer to the following list for showing group information. 2. Transmitter Operation Power on transmitter -Press and hold "UP"/"DOWN" button, release the button once the CH number begins to flash -When it is flashing, continue to press "UP"/"DOWN" button to increase /decrease channel orderly, select the same channel as chosen on receiver. -The selected channel will be save automatically for using without any action for 5 seconds. 3. Please pay attention: If hope to use multi-microphones together with better effect (less interference), we suggest to choose frequencies under same group for using. SYSTEM CONNECTION. Receiver Power Connection: Connect the DC connector of supplied C/DC adapter into the DC power input of receiver. Plug the C input connecter into an C20/60Hz or C220V/50Hz outlet. (Shown as below) 2. ntenna: Keep the position of antenna at a 45 angle from vertical,.(shown as below) djustable Freq. from Module to 4 djustable Freq. from Module 5 to CH: 0 CH: 02 CH: 03 CH: 04 CH: 05 CH: 06 CH: 07 CH: 0 Group "0" 623.200 626.625 639.400 645.075 673.225 677.975 66.375 695.375 CH: CH: 2 CH: 3 CH: 4 CH: 5 CH: 6 CH: 7 CH: Group "" 623.500 626.925 639.700 645.375 673.525 67.275 66.675 695.675 CH: 2 CH: 22 CH: 23 CH: 24 CH: 25 CH: 26 CH: 27 CH: 2 Group "2" 623.00 627.225 640.000 645.675 673.25 67.575 66.975 695.975 CH: 3 CH: 32 CH: 33 CH: 34 CH: 35 CH: 36 CH: 37 CH: 3 Group "3" 624.00 627.525 640.300 645.975 674.25 67.75 67.275 696.275 CH: 4 CH: 42 CH: 43 CH: 44 CH: 45 CH: 46 CH: 47 CH: 4 Group "4" 624.400 627.25 640.600 646.275 674.425 679.75 67.575 696.575 CH: 5 CH: 52 CH: 53 CH: 54 CH: 55 CH: 56 CH: 57 CH: 5 Group "5" 624.700 62.25 640.900 646.575 674.725 679.475 67.75 696.75 CH: 6 CH: 62 CH: 63 CH: 64 CH: 65 CH: 66 CH: 67 CH: 6 Group "6" 625.000 62.425 64.200 646.75 675.025 679.775 6.75 697.75 CH: 7 CH: 72 CH: 73 CH: 74 CH: 75 CH: 76 CH: 77 CH: 7 Group "7" 625.300 62.725 64.500 647.75 675.325 60.075 6.475 697.475 CH: CH: 2 CH: 3 CH: 4 CH: 5 CH: 6 CH: 7 CH: Group "" 625.600 629.025 64.00 647.475 675.625 60.375 6.775 697.775 3. udio Connection: Connect the corresponding output of receiver by supplied /4" phone jack audio cable or your XLR cable to the input of power amplifier, mixer. 7
3-5 500m 42MM X 223MM X 97MM X 2 7 257MM X 5.5MM X 5.5MM X 2 460 970 50 64 7 05MM X 65MM X 30MM 9 0