Product Information Packet Hydraulic Qwik-Lok Inch: March, 0 When the E Series product line was introduced, it was a best-in-industry choice for workholding. Over the years, Chick has built on that success, employing new manufacturing technologies, incorporating customer feedback, and continuing to work every day to support our mission of efficiency through workholding innovation. As the vast majority of our customers have experienced, the System line for batch production and the One-Lok TM CNC Vise one-off production offer even greater benefits in versatility, speed, strength, and efficiency than older Chick systems. Therefore, as of March, 0, no new complete E Series workholding systems will be sold. Qwik-Lok Manual Qwik-Lok Hydraulic Multi-Lok Specialty Multi-Lok QL QL-S Bi-Lok Manual Bi-Lok Hydraulic BL BL-S BL-QC BL-H BLH-QC MLA08 MLA08-LP MLB08 MLB MLB Chick will continue to support E Series customers with spare parts and accessories. While most E Series parts will continue to be a stocked item (see red circles on following pages), some items will not be stocked. These items will be available in one of the following ways: Items marked by a gray circle will be available only while supplies last. For example, bases will be available while we have the material and machines to make them. During this time, we will make sure that we have all of the items to be able to assemble the bases complete. However, when the material runs out, we will no longer offer these items. Made-to-order Items marked by a yellow circle (e.g., faceplates, jaw carriers, high jaws) will no longer be inventoried but will NOT be retired at this time. Instead, in an effort to support our customers, they will be available on a made-to-order basis. Note: Made-to-order items will require a $8 setup fee on every order (including repeat orders) regardless of quantity ordered and a minimum two-week delivery.
Bi-Lok Spare Parts and Accessories Overview RNDP-7-RD-0 Hydraulic manifold plate plugs (qty ) Slide assembly SP-SAS Manual aluminum SP-SAS-H Hydraulic SP-CVR Cover set SP-JP Jaw pin (includes jaw pin, O-ring) 8 7 JCL-0 QwikChange TM jaw carrier set SP-BAS-BL Bi-Lok base HS Swivel handle LHCS-00-0-0 Handle seal plate mounting screws 00-000 Handle seal plate / SP-WA Stop washer & stop washer screw ( sets) 7 RNDP--RD-0 Round plugs (qty ) 8 ELBL--7 Label (qty ) 00-0 Hydraulic manifold plate (includes mounting screws & plugs) SP-JPK Jaw pin knob (only) PE-. Pin extractor 7 SHCS-7-7-0 Fixed jaw mounting screws (qty ) 8 SP-TWR T-wrench 7 8 7.77. ChickWorkholding.com
Qwik-Lok Spare Parts Overview 0-070 Locating bushing (qty ) RNDP-7-BL-0 Hydraulic manifold plate plugs (qty ) Slide assembly 8 SP-SAS Manual aluminum SP-SAS-H Hydraulic 0 SP-CVR Cover set JQL-00AL-0 QwikChange TM dual station jaw (standard only) SP-JP Jaw pin (includes jaw pin, O-ring) 7 SP-BAS-QL Qwik-Lok base HS Swivel handle LHCS-00-0-0 Handle seal plate mounting screws (qty ) 00-000 Handle seal plate / SP-WA Stop washer & stop washer screw ( sets) 7 RNDP--RD-0 Round plugs (qty ) 8 RNDP-0-RD-0 Round plugs (qty ) ELBL--8 Label 00-0 Hydraulic manifold plate (includes mounting screws & plugs) 7 SP-JPK Jaw pin knob (only) 8 PE-. Pin extractor SHCS-7-0-0 Fixed jaw mounting screws (qty ) 0 SP-TWR T-wrench 7 8 7.77. ChickWorkholding.com
Multi-Lok Spare Parts and Accessories Overview 0-070 Locating bushing (qty ) Slide assembly 7 SP-SAS Manual Slide assembly SP-CVR Cover set JQL-00AL-0 QwikChange dual station jaw set (standard only) SP-JP Jaw pin (includes jaw pin, O-ring) Multi-Lok column SP-CLMA Low Profile SP-CLMB Standard ELBL-- Label (qty ) SP-TP Top plate LHCS-7-0-0 Top plate mounting screws (qty ) RNDP-0-RD-0 Round plugs (qty ) 8 HS Swivel handle SP-JPK Jaw pin knob (only) PE-. Pin extractor SHCS-7-0-0 Fixed jaw mounting screws (qty ) SP-TWR T-wrench 8 7 7.77. ChickWorkholding.com
QwikChange TM Accessories Overview JQL-00AL-0 QwikChange dual station jaw set (standard only) SP-JP Jaw pin (includes jaw pin, O-ring) SP-CVR Cover set QwikChange dual station jaw set JQL-8XAL-0 Wide JQL-00AL-0 High Not Applicable for QwikChange faceplate (standard) 8 FPQCA-XAL-0 Low Profile 8 FPQCB-XAL-0 Standard Height 7 QwikChange faceplate (wide) FPQCA-8XAL-0 Low Profile FPQCB-8XAL-0 Standard Height QwikChange jaw carrier set JCL-0 8 8 Not Applicable for 7 SHCS-7-0-0 Fixed jaw mounting screws (qty ) SHCS-7-7-0 Fixed jaw carrier mounting screws (qty ) Hard jaw plates (A) JHSTD-0 Standard (Set of ) (B) JHTHK-0 Thick (Set of ) Hard jaw plate mounting screws /- by (A) LHCS-00-0-008 /8 Long (qty 8) (B) SHCS-00--008 / Long (qty 8) (C) SHCS-00-7-008 / Long (qty 8) SHCS-00--008 Soft jaw plate mounting screws (qty ) Single station end plate 7 00-000 Bi-Lok Single station end plate 7 00-000 Qwik-Lok Single station end plate 8 SP-JPK Jaw pin knob (only) JSL-0 Soft jaw plate (set of ) 7 7.77. ChickWorkholding.com
SLIDE ASSEMBLY Spare Parts and Accessories Overview Slide Assembly, MANUAL Complete Slide Assembly -7 SP-SAS Standard -7 SP-SAS-S Steel,,, - ESRK Slide Rebuild Kit SP-THS Third Hand Screw 00-08 Clamping Block - EHWT Third Hand Hardware Kit SP-CVR Cover Set ( pieces) 7 00-0-00 Ball Plunger 00-0-0- O-Ring Seal - Large (Qty ) 00-0 Screw 00-0-00- O-Ring Seal - Small (Qty ) & 7 ESLD Slide 00-0-0- U-Cup Seal (Qty ) & 7 ESNT Slide Nut 7 7 8 Slide Assembly, HYDRAULIC -,, SP-SAS-H Hydraulic Slide Assembly 00-0-0 Compression Spring, -8,, ESRK-H Slide Rebuild Kit 00-0-00 Ball Plunger 00-0 Hex Ring 00-08 Hydraulic Clamping Block SP-THS Third Hand Screw -8 SP-HWT Third Hand Hardware Set (Qty ) SP-CVR Cover Set ( pieces) 00-0- Manifold Supply Tube SHCS-00-0-0 Manifold Plate Mounting Screws Hydraulic Manifold Plate 0 008-0 Bi-Lok 0 00-0 Qwik-Lok 7 8 7 8 Hydraulic Slide Assy (Conversion Kit) - PC-BL Bi-Lok Conversion Kit - PC-QL Qwik-Lok Conversion Kit 00-0 Hydraulic Slide Cap 00-0- Screw & SPH-SLD Hydraulic Slide & SPH-SNT Hydraulic Slide Nut 00-0-007 Manifold Plate Plugs (Qty ) 7.77. ChickWorkholding.com 0
Notes E SERIES DUAL STATION SET-UP: Jaw Center Jaw Jaw Third Hand Mechanism. Design and machine QwikChange Machinable Jaws to interface with the workpiece(s), or install hard jaws. NOTE: All reference surfaces must be located on the Center Jaw. Loosen the screw on the Third Hand Mechanism with the T-wrench.. Slide Jaw (moving jaw at the rear end of system) far enough from the Center Jaw to fi t the fi rst workpiece.. Insert the first workpiece against the Center Jaw and slide Jaw toward workpiece leaving a desired clearance. (Clearance range should fall between.00 to.0 ) NOTE: This clearance is set to ensure easy part removal when the system is unclamped, and will allow for variations in part size.. Tighten the screw on the Third Hand Mechanism until it bottoms. NOTE: Hand tightened screw only( Ft Lbs). Do not overtighten!. Remove the fi rst workpiece. 7. Adjust Jaw (moving jaw at the operator s end of system) using the T-wrench so that it is far enough from the Center Jaw to fi t the second workpiece. NOTE: The total travel of units is.0, units is.00. The total clearance for both Jaw and Jaw must be less than the overall travel of the unit. 8. Insert the both workpieces and turn power on. NOTE: If using a power booster, be sure the booster has a large enough volume to operate the set-up.. To unload workpieces, turn off power. Chick Hydraulic Workholding Systems are single acting (spring return). SET UP SINGLE STATION SET-UP: Jaw Jaw Third Hand Mechanism. Design and machine QwikChange Jaws to interface with the workpiece(s), or install hard jaws.. Bolt endplate to near end of Workholding System with four of the included socket head cap screws. NOTE: If setting up Multi-Lok skip step, since topplate is already bolted to Multi-Lok column.. Loosen the screw on the Third Hand Mechanism with the T-wrench. NOTE: Adjustment of the Third Hand Mechanism screw is not necessary when the system is used in the single station mode. It should be left in the loose condition to allow free movement of Jaw.. Slide Jaw fl ush with the end plate and bolt Jaw to the endplate with two of the included socket head cap screws. NOTE: All reference surfaces must be located on Jaw and/or the Center Jaw. Use the T-wrench to adjust Jaw to provide clearance to load workpieces.. Insert the workpiece and turn power on. NOTE: If using a power booster, be sure the booster has a large enough volume to operate the set-up. 7. To unload workpiece, turn off power. Chick Hydraulic Workholding Systems are single acting (spring return). CHICK WORKHOLDING SOLUTIONS, INC 00 Keystone Drive Warrendale, PA 08 USA Phone: (7) 77- Fax: (7) 77- Toll Free: (800) -CHICK (800) - www.chickworkholding.com Revised: 0-NOV-0 Document: 800-0-0 Page of
Notes E SERIES.7 END PLATE THROUGH HOLE WITH C'BORE ON FARSIDE FOR Ø /8 X.7 MINIMUM LENGTH BOLTS HOLES.0000 ±.000.000 Ø.000 X. DP HOLES FOR DOWEL PINS OR CHICK LOCATING KEYS HOLES JAW.00.0 CENTER JAW.0.0000 ±.000.000 JAW.00.000 ±.00.000 ±.00.000 DIMENSIONS THIRD HAND MECHANISM THIRD HAND SCREW. ±.00.7.00 SIZE SAE PORT PLACES.7.00 ±.00.7.. ±.00.000 CHICK WORKHOLDING SOLUTIONS, INC 00 Keystone Drive Warrendale, PA 08 USA Phone: (7) 77- Fax: (7) 77- Toll Free: (800) -CHICK (800) - www.chickworkholding.com Revised: 0-NOV-0 Document: 800-0-0 Page of
E SERIES Item Number Description A B C JQL-00AL.00 High Jaws.0.00. JQL-00AL.00 High Jaws.0.00. JQL-8XAL 8.00 Wide Jaws 7.0.00. A B Notes Grey area indicates No Cut zone.. MACHINABLE AREA.0.8.7 Ø. C CHICK WORKHOLDING SOLUTIONS, INC 00 Keystone Drive Warrendale, PA 08 USA Phone: (7) 77- Fax: (7) 77- Toll Free: (800) -CHICK (800) - www.chickworkholding.com Revised: 0-NOV-0 Document: 800-0-0 Page 7 of
Notes E SERIES END PLATE. 8..... STANDARD QWIKCHANGE FIXTURE JAWS. 8.. 8.. TOTAL SLIDE TRAVEL AVAILABLE STANDARD JAWS WITHOUT CENTER JAW JAW TRAVEL.7 CHICK WORKHOLDING SOLUTIONS, INC 00 Keystone Drive Warrendale, PA 08 USA Phone: (7) 77- Fax: (7) 77- Toll Free: (800) -CHICK (800) - www.chickworkholding.com Revised: 0-NOV-0 Document: 800-0-0 Page 8 of
Notes E SERIES Hydraulic Pressure Clamping Force (LB) (PSI) Average Front Rear 00 0 0 0 00 7 77 70 00 88 0 000 0 70 00 0 0 000 00 00 0 00 880 0 80 000 780 80 70 00 78 700 77 000 8 80 80 00 0 000 000 000 000 000 00 0 0 00 000 000 000 000 000 7000 8000 CLAMPING FORCE (LB) CLAMPING FORCE 000 000 CHICK WORKHOLDING SOLUTIONS, INC 00 Keystone Drive Warrendale, PA 08 USA Phone: (7) 77- Fax: (7) 77- Toll Free: (800) -CHICK (800) - www.chickworkholding.com Revised: 0-NOV-0 Document: 800-0-0 Page of HYDRAULIC PRESSURE (PSI) Note: Maximum Recommended Torque. Actual results may vary.